From e8701195e66f2d27ffe17fb514eae8173795aaf7 Mon Sep 17 00:00:00 2001
From: Georgiy Bondarenko <69736697+nehilo@users.noreply.github.com>
Date: Thu, 4 Mar 2021 22:54:23 +0500
Subject: Initial commit
---
Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h | 182 ++++++++++++++++++++++++++
1 file changed, 182 insertions(+)
create mode 100644 Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h
(limited to 'Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h')
diff --git a/Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h b/Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h
new file mode 100644
index 0000000..5ac119f
--- /dev/null
+++ b/Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h
@@ -0,0 +1,182 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+#pragma once
+
+/**
+ * BIQU BQ111-A4
+ *
+ * Applies to the following boards:
+ *
+ * BOARD_BIQU_BQ111_A4 (Hotend, Fan, Bed)
+ */
+
+#if NOT_TARGET(MCU_LPC1768)
+ #error "Oops! Make sure you have the LPC1768 environment selected in your IDE."
+#endif
+
+#ifndef BOARD_INFO_NAME
+ #define BOARD_INFO_NAME "BIQU Thunder B300 V1.0"
+#endif
+
+//
+// Limit Switches
+//
+#define X_MIN_PIN P1_24 // 10k pullup to 3.3V, 1K series
+#define X_MAX_PIN P1_25 // 10k pullup to 3.3V, 1K series
+#define Y_MIN_PIN P1_26 // 10k pullup to 3.3V, 1K series
+#define Y_MAX_PIN P1_27 // 10k pullup to 3.3V, 1K series
+#define Z_MIN_PIN P1_28 // 10k pullup to 3.3V, 1K series
+#define Z_MAX_PIN P1_29 // 10k pullup to 3.3V, 1K series
+
+//
+// Steppers
+//
+#define X_STEP_PIN P2_00
+#define X_DIR_PIN P0_05
+#define X_ENABLE_PIN P0_04
+#ifndef X_CS_PIN
+ #define X_CS_PIN P1_15 // ETH
+#endif
+
+#define Y_STEP_PIN P2_01
+#define Y_DIR_PIN P0_11
+#define Y_ENABLE_PIN P0_10
+#ifndef Y_CS_PIN
+ #define Y_CS_PIN P1_14 // ETH
+#endif
+
+#define Z_STEP_PIN P2_02
+#define Z_DIR_PIN P0_20
+#define Z_ENABLE_PIN P0_19
+#ifndef Z_CS_PIN
+ #define Z_CS_PIN P1_16 // ETH
+#endif
+
+#define E0_STEP_PIN P2_03
+#define E0_DIR_PIN P0_22
+#define E0_ENABLE_PIN P0_21
+#ifndef E0_CS_PIN
+ #define E0_CS_PIN P1_17 // ETH
+#endif
+
+//
+// Software SPI pins for TMC2130 stepper drivers
+//
+#if ENABLED(TMC_USE_SW_SPI)
+ #ifndef TMC_SW_MOSI
+ #define TMC_SW_MOSI P0_18 // ETH
+ #endif
+ #ifndef TMC_SW_MISO
+ #define TMC_SW_MISO P0_17 // ETH
+ #endif
+ #ifndef TMC_SW_SCK
+ #define TMC_SW_SCK P0_15 // ETH
+ #endif
+#endif
+
+//
+// Temperature Sensors
+// 3.3V max when defined as an analog input
+//
+#define TEMP_0_PIN P0_24_A1 // A0 (T0)
+#define TEMP_BED_PIN P0_23_A0 // A1 (T1)
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN P2_07
+#define HEATER_BED_PIN P2_05
+#ifndef FAN_PIN
+ #define FAN_PIN P2_04
+#endif
+
+//
+// Unused
+//
+//#define PIN_P2_10 P2_10 // IBOOT-1
+//#define PIN_P0_27 P0_27 // Onboard SD Detect
+
+/**
+ * LCD / Controller
+ *
+ * REPRAP_DISCOUNT_SMART_CONTROLLER is not supported due to the lack of LCD_PINS_D5,
+ * LCD_PINS_D6 or LCD_PINS_D7 in the EXP1 connector.
+ *
+ * A remote SD card is not supported as the pins routed to EXP2 are the same as used
+ * for the onboard SD card, and a chip select signal is not provided for the remote
+ * SD card.
+ */
+#if HAS_WIRED_LCD
+
+ #define BEEPER_PIN P1_31 // EXP1-1
+
+ #define BTN_EN1 P3_26 // EXP2-3
+ #define BTN_EN2 P3_25 // EXP2-5
+ #define BTN_ENC P1_30 // EXP1-2
+
+ #define SD_DETECT_PIN P0_27 // EXP2-7
+ #define LCD_PINS_RS P0_16 // EXP1-4
+ #define LCD_PINS_ENABLE P0_18 // (MOSI) EXP1-3
+ #define LCD_PINS_D4 P0_15 // (SCK) EXP1-5
+
+ #if BOTH(HAS_MARLINUI_HD44780, IS_RRD_SC)
+ #error "REPRAP_DISCOUNT_SMART_CONTROLLER displays aren't supported by the BIQU B300 v1.0"
+ #endif
+
+ #if ENABLED(SDSUPPORT)
+ #error "SDSUPPORT is not supported by the BIQU B300 v1.0 when an LCD controller is used"
+ #endif
+
+#endif // HAS_WIRED_LCD
+
+/**
+ * SD Card Reader
+ *
+ * Software SPI is used to interface with a stand-alone SD card reader connected to EXP1.
+ * Hardware SPI can't be used because P0_17 (MISO) is not brought out on this board.
+ */
+#if ENABLED(SDSUPPORT)
+ #define SD_SCK_PIN P0_15 // EXP1-5
+ #define SD_MISO_PIN P0_16 // EXP1-4
+ #define SD_MOSI_PIN P0_18 // EXP1-3
+ #define SD_SS_PIN P1_30 // EXP1-2
+ #define SDSS SD_SS_PIN
+#endif
+
+/**
+ * PWMS
+ *
+ * There are 6 PWMS. Each PWM can be assigned to one of two pins.
+ *
+ * PWM1.1 P0_18 LCD_PINS_ENABLE
+ * PWM1.1 P2_0 X_STEP_PIN
+ * PWM1.2 P1_20
+ * PWM1.2 P2_1 Y_STEP_PIN
+ * PWM1.3 P1_21
+ * PWM1.3 P2_2 Z_STEP_PIN
+ * PWM1.4 P1_23
+ * PWM1.4 P2_3 E0_STEP_PIN
+ * PWM1.5 P1_24 X_MIN_PIN
+ * PWM1.5 P2_4 FAN_PIN
+ * PWM1.6 P1_26 Y_MIN_PIN
+ * PWM1.6 P2_5 HEATER_BED_PIN
+ */
--
cgit v1.2.3