From e8701195e66f2d27ffe17fb514eae8173795aaf7 Mon Sep 17 00:00:00 2001 From: Georgiy Bondarenko <69736697+nehilo@users.noreply.github.com> Date: Thu, 4 Mar 2021 22:54:23 +0500 Subject: Initial commit --- Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h | 395 ++++++++++++++++++++++++++++++ 1 file changed, 395 insertions(+) create mode 100644 Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h (limited to 'Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h') diff --git a/Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h b/Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h new file mode 100644 index 0000000..b919eca --- /dev/null +++ b/Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h @@ -0,0 +1,395 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * MKS SGEN-L pin assignments + */ + +#if NOT_TARGET(MCU_LPC1768) + #error "Oops! Make sure you have the LPC1768 environment selected in your IDE." +#endif + +#define BOARD_INFO_NAME "MKS SGen-L" +#define BOARD_WEBSITE_URL "github.com/makerbase-mks/MKS-SGEN_L" + +// +// Servos +// +#define SERVO0_PIN P1_23 // SERVO P1.23 +#define SERVO1_PIN P2_00 // SERVO P2.0 + +// +// Trinamic Stallguard pins +// +#define X_DIAG_PIN P1_29 // X- +#define Y_DIAG_PIN P1_27 // Y- +#define Z_DIAG_PIN P1_25 // Z- +#define E0_DIAG_PIN P1_28 // X+ +#define E1_DIAG_PIN P1_26 // Y+ + +// +// Limit Switches +// +#ifdef X_STALL_SENSITIVITY + #define X_STOP_PIN X_DIAG_PIN + #if X_HOME_DIR < 0 + #define X_MAX_PIN P1_28 // X+ + #else + #define X_MIN_PIN P1_28 // X+ + #endif +#else + #define X_MIN_PIN P1_29 // X- + #define X_MAX_PIN P1_28 // X+ +#endif + +#ifdef Y_STALL_SENSITIVITY + #define Y_STOP_PIN Y_DIAG_PIN + #if Y_HOME_DIR < 0 + #define Y_MAX_PIN P1_26 // Y+ + #else + #define Y_MIN_PIN P1_26 // Y+ + #endif +#else + #define Y_MIN_PIN P1_27 // Y- + #define Y_MAX_PIN P1_26 // Y+ +#endif + +#ifdef Z_STALL_SENSITIVITY + #define Z_STOP_PIN Z_DIAG_PIN + #if Z_HOME_DIR < 0 + #define Z_MAX_PIN P1_24 // Z+ + #else + #define Z_MIN_PIN P1_24 // Z+ + #endif +#else + #define Z_MIN_PIN P1_25 // Z- + #define Z_MAX_PIN P1_24 // Z+ +#endif + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN P1_24 +#endif + +// +// Steppers +// +#define X_STEP_PIN P2_02 +#define X_DIR_PIN P2_03 +#define X_ENABLE_PIN P2_01 +#ifndef X_CS_PIN + #define X_CS_PIN P1_01 +#endif + +#define Y_STEP_PIN P0_19 +#define Y_DIR_PIN P0_20 +#define Y_ENABLE_PIN P2_08 +#ifndef Y_CS_PIN + #define Y_CS_PIN P1_08 +#endif + +#define Z_STEP_PIN P0_22 +#define Z_DIR_PIN P2_11 +#define Z_ENABLE_PIN P0_21 +#ifndef Z_CS_PIN + #define Z_CS_PIN P1_10 +#endif + +#define E0_STEP_PIN P2_13 +#define E0_DIR_PIN P0_11 +#define E0_ENABLE_PIN P2_12 +#ifndef E0_CS_PIN + #define E0_CS_PIN P1_15 +#endif + +#define E1_STEP_PIN P0_01 +#define E1_DIR_PIN P0_00 +#define E1_ENABLE_PIN P0_10 +#ifndef E1_CS_PIN + #define E1_CS_PIN P1_17 +#endif + +// +// Software SPI pins for TMC2130 stepper drivers +// +#if ENABLED(TMC_USE_SW_SPI) + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI P4_28 + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO P0_05 + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK P0_04 + #endif +#endif + +#if HAS_TMC_UART + /** + * TMC2208/TMC2209 stepper drivers + * + * Hardware serial communication ports. + * If undefined software serial is used according to the pins below + */ + //#define X_HARDWARE_SERIAL Serial1 + //#define X2_HARDWARE_SERIAL Serial1 + //#define Y_HARDWARE_SERIAL Serial1 + //#define Y2_HARDWARE_SERIAL Serial1 + //#define Z_HARDWARE_SERIAL Serial1 + //#define Z2_HARDWARE_SERIAL Serial1 + //#define E0_HARDWARE_SERIAL Serial1 + //#define E1_HARDWARE_SERIAL Serial1 + //#define E2_HARDWARE_SERIAL Serial1 + //#define E3_HARDWARE_SERIAL Serial1 + //#define E4_HARDWARE_SERIAL Serial1 + + // + // Software serial + // + + #define X_SERIAL_TX_PIN P1_04 + #define X_SERIAL_RX_PIN P1_01 + + #define Y_SERIAL_TX_PIN P1_09 + #define Y_SERIAL_RX_PIN P1_08 + + #define Z_SERIAL_TX_PIN P1_14 + #define Z_SERIAL_RX_PIN P1_10 + + #define E0_SERIAL_TX_PIN P1_16 + #define E0_SERIAL_RX_PIN P1_15 + + #define E1_SERIAL_TX_PIN P4_29 + #define E1_SERIAL_RX_PIN P1_17 + + #define Z2_SERIAL_TX_PIN P4_29 + #define Z2_SERIAL_RX_PIN P1_17 + + // Reduce baud rate to improve software serial reliability + #define TMC_BAUD_RATE 19200 +#endif // HAS_TMC_UART + +// +// Temperature Sensors +// 3.3V max when defined as an analog input +// +#define TEMP_0_PIN P0_23_A0 // Analog Input A0 (TH1) +#define TEMP_BED_PIN P0_24_A1 // Analog Input A1 (TB) +#define TEMP_1_PIN P0_25_A2 // Analog Input A2 (TH2) + +// +// Heaters / Fans +// +#define HEATER_BED_PIN P2_05 +#define HEATER_0_PIN P2_07 +#if HOTENDS == 1 + #ifndef FAN1_PIN + #define FAN1_PIN P2_06 + #endif +#else + #ifndef HEATER_1_PIN + #define HEATER_1_PIN P2_06 + #endif +#endif +#ifndef FAN_PIN + #define FAN_PIN P2_04 +#endif + +// +// Misc. Functions +// +#define LED_PIN P1_18 // Used as a status indicator +#define LED2_PIN P1_19 +#define LED3_PIN P1_20 +#define LED4_PIN P1_21 + +/** + * _____ _____ + * (BEEPER) 1.31 | · · | 1.30 (BTN_ENC) (MISO) 0.8 | · · | 0.7 (SD_SCK) + * (LCD_EN) 0.18 | · · | 0.16 (LCD_RS) (BTN_EN1) 3.25 | · · | 0.28 (SD_CS2) + * (LCD_D4) 0.15 | · · 0.17 (LCD_D5) (BTN_EN2) 3.26 | · · 0.9 (SD_MOSI) + * (LCD_D6) 1.0 | · · | 1.22 (LCD_D7) (SD_DETECT) 0.27 | · · | RST + * GND | · · | 5V GND | · · | NC + * ----- ----- + * EXP1 EXP2 + */ +#if HAS_WIRED_LCD + + #define BEEPER_PIN P1_31 + #define BTN_ENC P1_30 + + #if ENABLED(CR10_STOCKDISPLAY) + #define LCD_PINS_RS P1_00 + + #define BTN_EN1 P0_18 + #define BTN_EN2 P0_15 + + #define LCD_PINS_ENABLE P1_22 + #define LCD_PINS_D4 P0_17 + + #elif HAS_SPI_TFT // Config for Classic UI (emulated DOGM) and Color UI + #define TFT_CS_PIN P1_00 + #define TFT_A0_PIN P1_22 + #define TFT_DC_PIN P1_22 + #define TFT_MISO_PIN P0_08 + #define TFT_BACKLIGHT_PIN P0_18 + #define TFT_RESET_PIN P0_16 + + #define LCD_USE_DMA_SPI + + #define TOUCH_INT_PIN P0_17 + #define TOUCH_CS_PIN P0_15 + #define TOUCH_BUTTONS_HW_SPI + #define TOUCH_BUTTONS_HW_SPI_DEVICE 2 + + // Disable any LCD related PINs config + #define LCD_PINS_ENABLE -1 + #define LCD_PINS_RS -1 + + #ifndef TFT_BUFFER_SIZE + #define TFT_BUFFER_SIZE 1200 + #endif + #ifndef TFT_QUEUE_SIZE + #define TFT_QUEUE_SIZE 6144 + #endif + + #define BTN_EN1 P3_25 + #define BTN_EN2 P3_26 + + #elif IS_TFTGLCD_PANEL + + #undef BEEPER_PIN + #undef BTN_ENC + + #if ENABLED(TFTGLCD_PANEL_SPI) + #define TFTGLCD_CS P3_25 + #endif + + #else + + #define BTN_EN1 P3_25 + #define BTN_EN2 P3_26 + + #define LCD_SDSS P0_28 + + #if ENABLED(MKS_12864OLED_SSD1306) + + #define LCD_PINS_DC P0_17 + #define DOGLCD_CS P0_16 + #define DOGLCD_A0 LCD_PINS_DC + #define DOGLCD_SCK P0_15 + #define DOGLCD_MOSI P0_18 + + #define LCD_PINS_RS P1_00 + #define LCD_PINS_D7 P1_22 + #define KILL_PIN -1 // NC + + #else // !MKS_12864OLED_SSD1306 + + #define LCD_PINS_RS P0_16 + + #define LCD_PINS_ENABLE P0_18 + #define LCD_PINS_D4 P0_15 + + #if ENABLED(FYSETC_MINI_12864) + + #define DOGLCD_CS P0_18 + #define DOGLCD_A0 P0_16 + #define DOGLCD_SCK P0_07 + #define DOGLCD_MOSI P0_09 + + #define LCD_BACKLIGHT_PIN -1 + + #define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems + // results in LCD soft SPI mode 3, SD soft SPI mode 0 + + #define LCD_RESET_PIN P0_15 // Must be high or open for LCD to operate normally. + + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN P0_17 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN P1_00 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN P1_22 + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #define NEOPIXEL_PIN P0_17 + #endif + + #else // !FYSETC_MINI_12864 + + #if ENABLED(MKS_MINI_12864) + #define DOGLCD_CS P0_17 + #define DOGLCD_A0 P1_00 + #endif + + #if IS_ULTIPANEL + #define LCD_PINS_D5 P0_17 + #define LCD_PINS_D6 P1_00 + #define LCD_PINS_D7 P1_22 + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + + #endif + + #endif // !FYSETC_MINI_12864 + + #endif // !MKS_12864OLED_SSD1306 + + #endif // !CR10_STOCKDISPLAY + +#endif // HAS_WIRED_LCD + +#ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION ONBOARD +#endif + +#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card + +#if SD_CONNECTION_IS(LCD) || SD_CONNECTION_IS(ONBOARD) + #define SD_DETECT_PIN P0_27 + #define SD_SCK_PIN P0_07 + #define SD_MISO_PIN P0_08 + #define SD_MOSI_PIN P0_09 + #if SD_CONNECTION_IS(ONBOARD) + #define SD_SS_PIN ONBOARD_SD_CS_PIN + #else + #define SD_SS_PIN P0_28 + #endif +#elif SD_CONNECTION_IS(CUSTOM_CABLE) + #error "No custom SD drive cable defined for this board." +#endif + +// +// Other Pins +// +//#define PIN_P0_02 P0_02 // AUX1 (Interrupt Capable/ADC/Serial Port 0) +//#define PIN_P0_03 P0_03 // AUX1 (Interrupt Capable/ADC/Serial Port 0) +//#define PS_ON_PIN P1_23 // SERVO P1.23 -- cgit v1.2.3