From e8701195e66f2d27ffe17fb514eae8173795aaf7 Mon Sep 17 00:00:00 2001 From: Georgiy Bondarenko <69736697+nehilo@users.noreply.github.com> Date: Thu, 4 Mar 2021 22:54:23 +0500 Subject: Initial commit --- Marlin/src/pins/ramps/pins_3DRAG.h | 164 +++++++++++++++++++++++++++++++++++++ 1 file changed, 164 insertions(+) create mode 100644 Marlin/src/pins/ramps/pins_3DRAG.h (limited to 'Marlin/src/pins/ramps/pins_3DRAG.h') diff --git a/Marlin/src/pins/ramps/pins_3DRAG.h b/Marlin/src/pins/ramps/pins_3DRAG.h new file mode 100644 index 0000000..6c7f7f4 --- /dev/null +++ b/Marlin/src/pins/ramps/pins_3DRAG.h @@ -0,0 +1,164 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * 3DRAG (and K8200 / K8400) Arduino Mega with RAMPS v1.4 pin assignments + */ + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "3Drag" +#endif + +#ifndef DEFAULT_MACHINE_NAME + #define DEFAULT_MACHINE_NAME BOARD_INFO_NAME +#endif + +#ifndef DEFAULT_SOURCE_CODE_URL + #define DEFAULT_SOURCE_CODE_URL "3dprint.elettronicain.it" +#endif + +// +// Heaters / Fans +// +#define RAMPS_D8_PIN 9 +#define RAMPS_D9_PIN 8 +#define MOSFET_D_PIN 12 + +#ifndef CASE_LIGHT_PIN + #define CASE_LIGHT_PIN -1 // Hardware PWM but one is not available on expansion header +#endif + +#include "pins_RAMPS.h" + +// +// Limit Switches +// +#undef Z_MAX_PIN + +// +// Steppers +// +#undef Z_ENABLE_PIN +#define Z_ENABLE_PIN 63 + +// +// Heaters / Fans +// +#define HEATER_2_PIN 6 + +// +// Misc. Functions +// +#undef SDSS +#define SDSS 25 + +#undef SD_DETECT_PIN +#define SD_DETECT_PIN 53 + +// +// LCD / Controller +// +#if IS_ULTRA_LCD && IS_NEWPANEL + #undef BEEPER_PIN + + #undef LCD_PINS_RS + #undef LCD_PINS_ENABLE + #undef LCD_PINS_D4 + #undef LCD_PINS_D5 + #undef LCD_PINS_D6 + #undef LCD_PINS_D7 + #define LCD_PINS_RS 27 + #define LCD_PINS_ENABLE 29 + #define LCD_PINS_D4 37 + #define LCD_PINS_D5 35 + #define LCD_PINS_D6 33 + #define LCD_PINS_D7 31 + + // Buttons + #undef BTN_EN1 + #undef BTN_EN2 + #undef BTN_ENC + #define BTN_EN1 16 + #define BTN_EN2 17 + #define BTN_ENC 23 + +#else + + #define BEEPER_PIN 33 + +#endif // IS_ULTRA_LCD && IS_NEWPANEL + +/** + * M3/M4/M5 - Spindle/Laser Control + * + * If you want to control the speed of your spindle then you'll have + * have to sacrifce the Extruder and pull some signals off the Z stepper + * driver socket. + * + * The following assumes: + * - the Z stepper driver socket is empty + * - the extruder driver socket has a driver board plugged into it + * - the Z stepper wires are attached the the extruder connector + * + * If you want to keep the extruder AND don't have a LCD display then + * you can still control the power on/off and spindle direction. + * + * Where to get spindle signals + * + * stepper signal socket name socket name + * ------- + * SPINDLE_LASER_ENA_PIN /ENABLE O| |O VMOT + * MS1 O| |O GND + * MS2 O| |O 2B + * MS3 O| |O 2A + * /RESET O| |O 1A + * /SLEEP O| |O 1B + * SPINDLE_LASER_PWM_PIN STEP O| |O VDD + * SPINDLE_DIR_PIN DIR O| |O GND + * ------- + * + * Note: Socket names vary from vendor to vendor + */ +#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are not good with 3DRAG +#undef SPINDLE_LASER_ENA_PIN +#undef SPINDLE_DIR_PIN + +#if HAS_CUTTER + #if !EXTRUDERS + #undef E0_DIR_PIN + #undef E0_ENABLE_PIN + #undef E0_STEP_PIN + #undef Z_DIR_PIN + #undef Z_ENABLE_PIN + #undef Z_STEP_PIN + #define Z_DIR_PIN 28 + #define Z_ENABLE_PIN 24 + #define Z_STEP_PIN 26 + #define SPINDLE_LASER_PWM_PIN 46 // Hardware PWM + #define SPINDLE_LASER_ENA_PIN 62 // Pullup! + #define SPINDLE_DIR_PIN 48 + #elif !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // Use expansion header if no LCD in use + #define SPINDLE_LASER_ENA_PIN 16 // Pullup or pulldown! + #define SPINDLE_DIR_PIN 17 + #endif +#endif -- cgit v1.2.3