From e8701195e66f2d27ffe17fb514eae8173795aaf7 Mon Sep 17 00:00:00 2001 From: Georgiy Bondarenko <69736697+nehilo@users.noreply.github.com> Date: Thu, 4 Mar 2021 22:54:23 +0500 Subject: Initial commit --- Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h | 344 ++++++++++++++++++++++++ 1 file changed, 344 insertions(+) create mode 100644 Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h (limited to 'Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h') diff --git a/Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h b/Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h new file mode 100644 index 0000000..af27159 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h @@ -0,0 +1,344 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Sanguinololu board pin assignments + */ + +/** + * Rev B 26 DEC 2016 + * + * 1) added pointer to a current Arduino IDE extension + * 2) added support for M3, M4 & M5 spindle control commands + * 3) added case light pin definition + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega1284P__) + #error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644P' or 'ATmega1284P' in 'Tools > Processor.'" +#endif + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "Sanguinololu <1.2" +#endif + +// +// Limit Switches +// +#define X_STOP_PIN 18 +#define Y_STOP_PIN 19 +#define Z_STOP_PIN 20 + +// +// Steppers +// +#define X_STEP_PIN 15 +#define X_DIR_PIN 21 + +#define Y_STEP_PIN 22 +#define Y_DIR_PIN 23 + +#define Z_STEP_PIN 3 +#define Z_DIR_PIN 2 + +#define E0_STEP_PIN 1 +#define E0_DIR_PIN 0 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 7 // Analog Input (pin 33 extruder) +#define TEMP_BED_PIN 6 // Analog Input (pin 34 bed) + +// +// Heaters / Fans +// +#define HEATER_0_PIN 13 // (extruder) + +#if ENABLED(SANGUINOLOLU_V_1_2) + + #define HEATER_BED_PIN 12 // (bed) + #define X_ENABLE_PIN 14 + #define Y_ENABLE_PIN 14 + #define Z_ENABLE_PIN 26 + #define E0_ENABLE_PIN 14 + + #if !defined(FAN_PIN) && ENABLED(LCD_I2C_PANELOLU2) + #define FAN_PIN 4 // Uses Transistor1 (PWM) on Panelolu2's Sanguino Adapter Board to drive the fan + #endif + +#else + + #define HEATER_BED_PIN 14 // (bed) + #define X_ENABLE_PIN 4 + #define Y_ENABLE_PIN 4 + #define Z_ENABLE_PIN 4 + #define E0_ENABLE_PIN 4 + +#endif + +#if !defined(FAN_PIN) && (MB(AZTEEG_X1, STB_11) || IS_MELZI) + #define FAN_PIN 4 // Works for Panelolu2 too +#endif + +// +// Misc. Functions +// + +/** + * In some versions of the Sanguino libraries the pin + * definitions are wrong, with SDSS = 24 and LED_PIN = 28 (Melzi). + * If you encounter issues with these pins, upgrade your + * Sanguino libraries! See #368. + */ +//#define SDSS 24 +#define SDSS 31 + +#if IS_MELZI + #define LED_PIN 27 +#elif MB(STB_11) + #define LCD_BACKLIGHT_PIN 17 // LCD backlight LED +#endif + +#if NONE(SPINDLE_FEATURE, LASER_FEATURE) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // try to use IO Header + #define CASE_LIGHT_PIN 4 // Hardware PWM - see if IO Header is available +#endif + +/** + * Sanguinololu 1.4 AUX pins: + * + * PWM TX1 RX1 SDA SCL + * 12V 5V D12 D11 D10 D17 D16 + * GND GND D31 D30 D29 D28 D27 + * A4 A3 A2 A1 A0 + */ + +// +// LCD / Controller +// +#if HAS_WIRED_LCD + + #define SD_DETECT_PIN -1 + + #if HAS_MARLINUI_U8GLIB + + #if ENABLED(LCD_FOR_MELZI) + + #define LCD_PINS_RS 17 + #define LCD_PINS_ENABLE 16 + #define LCD_PINS_D4 11 + #define KILL_PIN 10 + #define BEEPER_PIN 27 + + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 DELAY_NS(0) + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 DELAY_NS(188) + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 DELAY_NS(0) + #endif + + #elif ENABLED(U8GLIB_ST7920) // SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0 + + #if IS_MELZI + #define LCD_PINS_RS 30 // CS chip select /SS chip slave select + #define LCD_PINS_ENABLE 29 // SID (MOSI) + #define LCD_PINS_D4 17 // SCK (CLK) clock + // Pin 27 is taken by LED_PIN, but Melzi LED does nothing with + // Marlin so this can be used for BEEPER_PIN. You can use this pin + // with M42 instead of BEEPER_PIN. + #define BEEPER_PIN 27 + + #if IS_RRD_FG_SC + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 DELAY_NS(0) + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 DELAY_NS(188) + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 DELAY_NS(0) + #endif + #endif + + #else // Sanguinololu >=1.3 + #define LCD_PINS_RS 4 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 30 + #define LCD_PINS_D5 29 + #define LCD_PINS_D6 28 + #define LCD_PINS_D7 27 + #endif + + #else + + #define DOGLCD_A0 30 + + #if ENABLED(MAKRPANEL) + + #define BEEPER_PIN 29 + #define DOGLCD_CS 17 + #define LCD_BACKLIGHT_PIN 28 // PA3 + + #elif IS_MELZI + + #define BEEPER_PIN 27 + #define DOGLCD_CS 28 + + #else // !MAKRPANEL + + #define DOGLCD_CS 29 + + #endif + + #endif + + // Uncomment screen orientation + //#define LCD_SCREEN_ROT_0 + //#define LCD_SCREEN_ROT_90 + //#define LCD_SCREEN_ROT_180 + //#define LCD_SCREEN_ROT_270 + + #elif ENABLED(ZONESTAR_LCD) // For the Tronxy Melzi boards + + #define LCD_PINS_RS 28 + #define LCD_PINS_ENABLE 29 + #define LCD_PINS_D4 10 + #define LCD_PINS_D5 11 + #define LCD_PINS_D6 16 + #define LCD_PINS_D7 17 + + #else + + #define LCD_PINS_RS 4 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 30 + #define LCD_PINS_D5 29 + #define LCD_PINS_D6 28 + #define LCD_PINS_D7 27 + + #endif + + #if ENABLED(LCD_FOR_MELZI) + + #define BTN_ENC 28 + #define BTN_EN1 29 + #define BTN_EN2 30 + + #elif ENABLED(ZONESTAR_LCD) // For the Tronxy Melzi boards + + #define ADC_KEYPAD_PIN 1 + #define BTN_EN1 -1 + #define BTN_EN2 -1 + + #elif ENABLED(LCD_I2C_PANELOLU2) + + #if IS_MELZI + #define BTN_ENC 29 + #define LCD_SDSS 30 // Panelolu2 SD card reader rather than the Melzi + #else + #define BTN_ENC 30 + #endif + + #else // !LCD_FOR_MELZI && !ZONESTAR_LCD && !LCD_I2C_PANELOLU2 + + #define BTN_ENC 16 + #define LCD_SDSS 28 // Smart Controller SD card reader rather than the Melzi + + #endif + + #if IS_NEWPANEL && !defined(BTN_EN1) + #define BTN_EN1 11 + #define BTN_EN2 10 + #endif + +#endif // HAS_WIRED_LCD + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if HAS_CUTTER + #if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // try to use IO Header + + #define SPINDLE_LASER_ENA_PIN 10 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 4 // Hardware PWM + #define SPINDLE_DIR_PIN 11 + + #elif !MB(MELZI) // use X stepper motor socket + + /** + * To control the spindle speed and have an LCD you must sacrifice + * the Extruder and pull some signals off the X stepper driver socket. + * + * The following assumes: + * - The X stepper driver socket is empty + * - The extruder driver socket has a driver board plugged into it + * - The X stepper wires are attached the the extruder connector + */ + + /** + * Where to get the spindle signals + * + * spindle signal socket name socket name + * ------- + * /ENABLE O| |O VMOT + * MS1 O| |O GND + * MS2 O| |O 2B + * MS3 O| |O 2A + * /RESET O| |O 1A + * /SLEEP O| |O 1B + * SPINDLE_LASER_PWM_PIN STEP O| |O VDD + * SPINDLE_LASER_ENA_PIN DIR O| |O GND + * ------- + * + * Note: Socket names vary from vendor to vendor. + */ + #undef X_DIR_PIN + #undef X_ENABLE_PIN + #undef X_STEP_PIN + #define X_DIR_PIN 0 + #define X_ENABLE_PIN 14 + #define X_STEP_PIN 1 + #define SPINDLE_LASER_PWM_PIN 15 // Hardware PWM + #define SPINDLE_LASER_ENA_PIN 21 // Pullup! + #define SPINDLE_DIR_PIN -1 // No pin available on the socket for the direction pin + #endif +#endif -- cgit v1.2.3