From e8701195e66f2d27ffe17fb514eae8173795aaf7 Mon Sep 17 00:00:00 2001 From: Georgiy Bondarenko <69736697+nehilo@users.noreply.github.com> Date: Thu, 4 Mar 2021 22:54:23 +0500 Subject: Initial commit --- Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h | 318 +++++++++++++++++++++++++++ 1 file changed, 318 insertions(+) create mode 100644 Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h (limited to 'Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h') diff --git a/Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h b/Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h new file mode 100644 index 0000000..c49c31e --- /dev/null +++ b/Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h @@ -0,0 +1,318 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * FLSUN HiSpeed V1 (STM32F103VET6) board pin assignments + * FLSun Hispeed (clone MKS_Robin_miniV2) board. + * + * MKS Robin Mini USB uses UART3 (PB10-TX, PB11-RX) + * #define SERIAL_PORT_2 3 + */ + +#if NOT_TARGET(__STM32F1__, STM32F1xx) + #error "Oops! Select an STM32F1 board in 'Tools > Board.'" +#elif HOTENDS > 1 || E_STEPPERS > 1 + #error "FLSUN HiSpeedV1 only supports one hotend / E-stepper. Comment out this line to continue." +#endif + +#define BOARD_INFO_NAME "FLSun HiSpeedV1" +#define BOARD_WEBSITE_URL "github.com/Foxies-CSTL" + +#define BOARD_NO_NATIVE_USB + +// Avoid conflict with TIMER_SERVO when using the STM32 HAL +#define TEMP_TIMER 5 + +// +// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role +// +#define DISABLE_DEBUG + +// +// EEPROM +// +#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION) + #define FLASH_EEPROM_EMULATION + #define EEPROM_PAGE_SIZE (0x800U) // 2KB + #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL) + #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE // 2KB +#endif + +// +// SPI +// Note: FLSun Hispeed (clone MKS_Robin_miniV2) board is using SPI2 interface. +// +#define SD_SCK_PIN PB13 // SPI2 +#define SD_MISO_PIN PB14 // SPI2 +#define SD_MOSI_PIN PB15 // SPI2 +#define SPI_DEVICE 2 + +// SPI Flash +#define HAS_SPI_FLASH 1 +#define SPI_FLASH_SIZE 0x1000000 // 16MB + +#if HAS_SPI_FLASH + // SPI 2 + #define W25QXX_CS_PIN PB12 // SPI2_NSS / Flash chip-select + #define W25QXX_MOSI_PIN PB15 + #define W25QXX_MISO_PIN PB14 + #define W25QXX_SCK_PIN PB13 +#endif + +// +// Servos +// +//#define SERVO0_PIN PA8 // use IO0 to enable BLTOUCH support/remove Mks_Wifi + +// +// Limit Switches +// +#define X_STOP_PIN PA15 // -X +#define Y_STOP_PIN PA12 // -Y +#define Z_MIN_PIN PA11 // -Z +#define Z_MAX_PIN PC4 // +Z + +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN MT_DET_1_PIN +#endif + +// +// Steppers +// +#define X_ENABLE_PIN PE4 // X_EN +#define X_STEP_PIN PE3 // X_STEP +#define X_DIR_PIN PE2 // X_DIR + +#define Y_ENABLE_PIN PE1 // Y_EN +#define Y_STEP_PIN PE0 // Y_STEP +#define Y_DIR_PIN PB9 // Y_DIR + +#define Z_ENABLE_PIN PB8 // Z_EN +#define Z_STEP_PIN PB5 // Z_STEP +#define Z_DIR_PIN PB4 // Z_DIR + +#define E0_ENABLE_PIN PB3 // E0_EN +#define E0_STEP_PIN PD6 // E0_STEP +#define E0_DIR_PIN PD3 // E0_DIR + +/** + * FLSUN Hi-Speed has no hard-wired UART pins for TMC drivers. + * Several wiring options are provided below, defaulting to + * to the most compatible. + */ +#if HAS_TMC_UART + // SoftwareSerial with one pin per driver + // Compatible with TMC2208 and TMC2209 drivers + #define X_SERIAL_TX_PIN PA10 // RXD1 + #define X_SERIAL_RX_PIN PA10 // RXD1 + #define Y_SERIAL_TX_PIN PA9 // TXD1 + #define Y_SERIAL_RX_PIN PA9 // TXD1 + #define Z_SERIAL_TX_PIN PC7 // IO1 + #define Z_SERIAL_RX_PIN PC7 // IO1 + #define TMC_BAUD_RATE 19200 +#else + // Motor current PWM pins + #define MOTOR_CURRENT_PWM_XY_PIN PA6 // VREF2/3 CONTROL XY + #define MOTOR_CURRENT_PWM_Z_PIN PA7 // VREF4 CONTROL Z + #define MOTOR_CURRENT_PWM_RANGE 1500 // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp + #ifndef DEFAULT_PWM_MOTOR_CURRENT + #define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 } + #endif + + /** + * MKS Robin_Wifi or another ESP8266 module + * + * __ESP(M1)__ -J1- + * GND| 15 | | 08 |+3v3 (22) RXD1 (PA10) + * | 16 | | 07 |MOSI (21) TXD1 (PA9) Active LOW, probably OK to leave floating + * IO2| 17 | | 06 |MISO (19) IO1 (PC7) Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating) + * IO0| 18 | | 05 |CLK (18) IO0 (PA8) Must be HIGH (ESP3D software configures this with a pullup so OK to leave as floating) + * IO1| 19 | | 03 |EN (03) WIFI_EN Must be HIGH for module to run + * | nc | | nc | (01) WIFI_CTRL (PA5) + * RX| 21 | | nc | + * TX| 22 | | 01 |RST + * ￣￣ AE￣￣ + */ + // Module ESP-WIFI + #define ESP_WIFI_MODULE_COM 2 // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this + #define ESP_WIFI_MODULE_BAUDRATE BAUDRATE // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2 + #define ESP_WIFI_MODULE_RESET_PIN PA5 // WIFI CTRL/RST + #define ESP_WIFI_MODULE_ENABLE_PIN -1 + #define ESP_WIFI_MODULE_TXD_PIN PA9 // MKS or ESP WIFI RX PIN + #define ESP_WIFI_MODULE_RXD_PIN PA10 // MKS or ESP WIFI TX PIN +#endif + +// +// EXTRUDER +// +#if AXIS_DRIVER_TYPE_E0(TMC2208) || AXIS_DRIVER_TYPE_E0(TMC2209) + #define E0_SERIAL_TX_PIN PA8 // IO0 + #define E0_SERIAL_RX_PIN PA8 // IO0 + #define TMC_BAUD_RATE 19200 +#else + // Motor current PWM pins + #define MOTOR_CURRENT_PWM_E_PIN PB0 // VREF1 CONTROL E + #define MOTOR_CURRENT_PWM_RANGE 1500 // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp + #ifndef DEFAULT_PWM_MOTOR_CURRENT + #define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 } + #endif +#endif + +// +// Temperature Sensors (THM) +// +#define TEMP_0_PIN PC1 // TEMP_E0 +#define TEMP_BED_PIN PC0 // TEMP_BED + +// +// Heaters / Fans +// +#define HEATER_0_PIN PC3 // HEATER_E0 +#define HEATER_BED_PIN PA0 // HEATER_BED-WKUP + +#define FAN_PIN PB1 // E_FAN + +// +// Misc. Functions +// +//#define POWER_LOSS_PIN PA1 // PW_SO +#if ENABLED(BACKUP_POWER_SUPPLY) + #define POWER_LOSS_PIN PA2 // PW_DET (UPS) MKSPWC +#endif + +/** + * Connector J2 + * ------- + * DIO O|1 2|O 3v3 + * CSK O|3 5|O GND + * RST O|5 6|O GND + * ------- + */ +//#define SW_DIO PA13 +//#define SW_CLK PA14 +//#define SW_RST NRST // (14) + +// +// Power Supply Control +// +#if ENABLED(PSU_CONTROL) + #define KILL_PIN PA2 // PW_DET + #define KILL_PIN_INVERTING true + //#define PS_ON_PIN PA3 // PW_CN /PW_OFF +#endif + +#define MT_DET_1_PIN PA4 // MT_DET +#define MT_DET_2_PIN PE6 // FALA_CRTL +#define MT_DET_PIN_INVERTING false + +// +// LED / NEOPixel +// +//#define LED_PIN PB2 // BOOT1 + +#if ENABLED(NEOPIXEL_LED) + #define LED_PWM PC7 // IO1 + #ifndef NEOPIXEL_PIN + #define NEOPIXEL_PIN LED_PWM // USED WIFI IO0/IO1 PIN + #endif +#endif + +// +// SD Card +// +#ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION ONBOARD +#endif + +// Use the on-board card socket labeled SD_Extender +#if SD_CONNECTION_IS(CUSTOM_CABLE) + #define SD_SCK_PIN PC12 + #define SD_MISO_PIN PC8 + #define SD_MOSI_PIN PD2 + #define SD_SS_PIN -1 + #define SD_DETECT_PIN PD12 // SD_CD (if -1 no detection) +#else + #define SDIO_SUPPORT + #define SDIO_CLOCK 4500000 // 4.5 MHz + #define SDIO_READ_RETRIES 16 + #define ONBOARD_SPI_DEVICE 1 // SPI1 + #define ONBOARD_SD_CS_PIN PC11 + #define SD_DETECT_PIN -1 // SD_CD (-1 active refresh) +#endif + +// +// LCD / Controller +// +#ifndef BEEPER_PIN + #define BEEPER_PIN PC5 +#endif + +#if ENABLED(SPEAKER) && BEEPER_PIN == PC5 + #error "FLSun HiSpeed default BEEPER_PIN is not a SPEAKER." +#endif + +#if HAS_FSMC_TFT || HAS_GRAPHICAL_TFT + #define TFT_CS_PIN PD7 // NE4 + #define TFT_RS_PIN PD11 // A0 +#endif + +#if HAS_FSMC_TFT + /** + * Note: MKS Robin TFT screens use various TFT controllers + * Supported screens are based on the ILI9341, ST7789V and ILI9328 (320x240) + * ILI9488 is not supported + * Define init sequences for other screens in u8g_dev_tft_320x240_upscale_from_128x64.cpp + * + * If the screen stays white, disable 'LCD_RESET_PIN' + * to let the bootloader init the screen. + * + * Setting an 'LCD_RESET_PIN' may cause a flicker when entering the LCD menu + * because Marlin uses the reset as a failsafe to revive a glitchy LCD. + */ + //#define TFT_RESET_PIN PC6 // FSMC_RST + #define TFT_BACKLIGHT_PIN PD13 + #define FSMC_CS_PIN TFT_CS_PIN // NE4 + #define FSMC_RS_PIN TFT_RS_PIN // A0 + + #define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT + #define FSMC_DMA_DEV DMA2 + #define FSMC_DMA_CHANNEL DMA_CH5 + #ifdef TFT_CLASSIC_UI + #define TFT_MARLINBG_COLOR 0x3186 // Grey + #define TFT_MARLINUI_COLOR 0xC7B6 // Green + #define TFT_BTARROWS_COLOR 0xDEE6 // Yellow + #define TFT_BTOKMENU_COLOR 0x145F // Cyan + #endif + #define TFT_BUFFER_SIZE 14400 +#elif HAS_GRAPHICAL_TFT + #define TFT_RESET_PIN PC6 + #define TFT_BACKLIGHT_PIN PD13 +#endif + +#if NEED_TOUCH_PINS + #define TOUCH_CS_PIN PC2 // SPI2_NSS + #define TOUCH_SCK_PIN PB13 // SPI2_SCK + #define TOUCH_MISO_PIN PB14 // SPI2_MISO + #define TOUCH_MOSI_PIN PB15 // SPI2_MOSI + #define TOUCH_INT_PIN -1 +#endif -- cgit v1.2.3