/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ /** * lcd/extui/lib/chiron_defs.h * * Extensible_UI implementation for Anycubic Chiron * Written By Nick Wells, 2020 [https://github.com/SwiftNick] * (not affiliated with Anycubic, Ltd.) */ #pragma once #include "../../../../inc/MarlinConfigPre.h" //#define ACDEBUGLEVEL 255 #if ACDEBUGLEVEL // Bit-masks for selective debug: enum ACDebugMask : uint8_t { AC_INFO = 1, AC_ACTION = 2, AC_FILE = 4, AC_PANEL = 8, AC_MARLIN = 16, AC_SOME = 32, AC_ALL = 64 }; #define ACDEBUG(mask) ( ((mask) & ACDEBUGLEVEL) == mask ) // Debug flag macro #else #define ACDEBUG(mask) false #endif #define TFTSer LCD_SERIAL // Serial interface for TFT panel now uses marlinserial #define MAX_FOLDER_DEPTH 4 // Limit folder depth TFT has a limit for the file path #define MAX_CMND_LEN 16 * MAX_FOLDER_DEPTH // Maximum Length for a Panel command #define MAX_PATH_LEN 16 * MAX_FOLDER_DEPTH // Maximum number of characters in a SD file path #define AC_HEATER_FAULT_VALIDATION_TIME 5 // number of 1/2 second loops before signalling a heater fault #define AC_LOWEST_MESHPOINT_VAL Z_PROBE_LOW_POINT // The lowest value you can set for a single mesh point offset // TFT panel commands #define AC_msg_sd_card_inserted PSTR("J00") #define AC_msg_sd_card_removed PSTR("J01") #define AC_msg_no_sd_card PSTR("J02") #define AC_msg_usb_connected PSTR("J03") #define AC_msg_print_from_sd_card PSTR("J04") #define AC_msg_pause PSTR("J05") #define AC_msg_nozzle_heating PSTR("J06") #define AC_msg_nozzle_heating_done PSTR("J07") #define AC_msg_bed_heating PSTR("J08") #define AC_msg_bed_heating_done PSTR("J09") #define AC_msg_nozzle_temp_abnormal PSTR("J10") #define AC_msg_kill_lcd PSTR("J11") #define AC_msg_ready PSTR("J12") #define AC_msg_low_nozzle_temp PSTR("J13") #define AC_msg_print_complete PSTR("J14") #define AC_msg_filament_out_alert PSTR("J15") #define AC_msg_stop PSTR("J16") #define AC_msg_main_board_has_reset PSTR("J17") #define AC_msg_paused PSTR("J18") #define AC_msg_j19_unknown PSTR("J19") #define AC_msg_sd_file_open_success PSTR("J20") #define AC_msg_sd_file_open_failed PSTR("J21") #define AC_msg_level_monitor_finished PSTR("J22") #define AC_msg_filament_out_block PSTR("J23") #define AC_msg_probing_not_allowed PSTR("J24") #define AC_msg_probing_complete PSTR("J25") #define AC_msg_start_probing PSTR("J26") #define AC_msg_version PSTR("J27") #define MARLIN_msg_start_probing PSTR("Probing Point 1/25") #define MARLIN_msg_probing_failed PSTR("Probing Failed") #define MARLIN_msg_ready PSTR(" Ready.") #define MARLIN_msg_print_paused PSTR("Print Paused") #define MARLIN_msg_print_aborted PSTR("Print Aborted") #define MARLIN_msg_extruder_heating PSTR("E Heating...") #define MARLIN_msg_bed_heating PSTR("Bed Heating...") #define MARLIN_msg_nozzle_parked PSTR("Nozzle Parked") #define MARLIN_msg_heater_timeout PSTR("Heater Timeout") #define MARLIN_msg_reheating PSTR("Reheating...") #define MARLIN_msg_reheat_done PSTR("Reheat finished.") #define MARLIN_msg_filament_purging PSTR("Filament Purging...") #define MARLIN_msg_special_pause PSTR("PB") #define AC_cmnd_auto_unload_filament PSTR("M701") // Use Marlin unload routine #define AC_cmnd_auto_load_filament PSTR("M702 M0 PB") // Use Marlin load routing then pause for user to clean nozzle #define AC_cmnd_manual_load_filament PSTR("M83\nG1 E50 F700\nM82") // replace the manual panel commands with something a little faster #define AC_cmnd_manual_unload_filament PSTR("M83\nG1 E-50 F1200\nM82") #define AC_cmnd_enable_leveling PSTR("M420SV") #define AC_cmnd_power_loss_recovery PSTR("G28XYR5\nG28Z") // Lift, home X and Y then home Z when in 'safe' position namespace Anycubic { enum heater_state_t : uint8_t { AC_heater_off, AC_heater_temp_set, AC_heater_temp_reached }; enum paused_state_t : uint8_t { AC_paused_heater_timed_out, AC_paused_purging_filament, AC_paused_idle }; enum printer_state_t : uint8_t { AC_printer_idle, AC_printer_probing, AC_printer_printing, AC_printer_pausing, AC_printer_paused, AC_printer_stopping, AC_printer_resuming_from_power_outage }; enum timer_event_t : uint8_t { AC_timer_started, AC_timer_paused, AC_timer_stopped }; enum media_event_t : uint8_t { AC_media_inserted, AC_media_removed, AC_media_error }; enum file_menu_t : uint8_t { AC_menu_file, AC_menu_command, AC_menu_change_to_file, AC_menu_change_to_command }; }