/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
 *
 */
#pragma once

/**
 * Leapfrog Xeed Driver board pin assignments
 *
 * This board is used by other Leapfrog printers in addition to the Xeed,
 * such as the Creatr HS and Bolt. The pin assignments vary wildly between
 * printer models. As such this file is currently specific to the Xeed.
 */

#if NOT_TARGET(__AVR_ATmega2560__)
  #error "Oops! Select 'Mega 2560' in 'Tools > Board.'"
#endif

#define BOARD_INFO_NAME "Leapfrog Xeed 2015"

//
// Limit Switches
//
#define X_STOP_PIN                            47  // 'X Min'
#define Y_STOP_PIN                            48  // 'Y Min'
#define Z_STOP_PIN                            49  // 'Z Min'

//
// Steppers
// The Xeed utilizes three Z-axis motors, which use the X, Y, and Z stepper connectors
// on the board. The X and Y steppers use external drivers, attached to signal-level
// Y-axis and X-axis connectors on the board, which map to distinct CPU pins from
// the on-board X/Y stepper drivers.
//

// X-axis signal-level connector
#define X_STEP_PIN                            65
#define X_DIR_PIN                             64
#define X_ENABLE_PIN                          66  // Not actually used on Xeed, could be repurposed

// Y-axis signal-level connector
#define Y_STEP_PIN                            23
#define Y_DIR_PIN                             22
#define Y_ENABLE_PIN                          24  // Not actually used on Xeed, could be repurposed

// ZMOT connector (Front Right Z Motor)
#define Z_STEP_PIN                            31
#define Z_DIR_PIN                             32
#define Z_ENABLE_PIN                          30

// XMOT connector (Rear Z Motor)
#define Z2_STEP_PIN                           28
#define Z2_DIR_PIN                            63
#define Z2_ENABLE_PIN                         29

// YMOT connector (Front Left Z Motor)
#define Z3_STEP_PIN                           14
#define Z3_DIR_PIN                            15
#define Z3_ENABLE_PIN                         39

// EMOT2 connector
#define E0_STEP_PIN                           37
#define E0_DIR_PIN                            40
#define E0_ENABLE_PIN                         36

// EMOT connector
#define E1_STEP_PIN                           34
#define E1_DIR_PIN                            35
#define E1_ENABLE_PIN                         33

//
// Filament runout
//
#define FIL_RUNOUT_PIN                        42  // ROT2 Connector
#define FIL_RUNOUT2_PIN                       44  // ROT1 Connector

//
// Temperature Sensors
//
#define TEMP_0_PIN                            15  // T3 Connector
#define TEMP_1_PIN                            13  // T1 Connector
#define TEMP_BED_PIN                          14  // BED Connector (Between T1 and T3)

//
// Heaters / Fans
//
#define HEATER_0_PIN                           8  // Misc Connector, pins 3 and 4 (Out2)
#define HEATER_1_PIN                           9  // Misc Connector, pins 5 and 6 (Out3)
#define HEATER_BED_PIN                         6  // Misc Connector, pins 9(-) and 10(+) (OutA)

#define FAN_PIN                               10  // Misc Connector, pins 7(-) and 8 (+) (Out4)

#define LED_PIN                               13

#define SOL1_PIN                               7  // Misc Connector, pins 1(-) and 2(+) (Out1)

// Door Closed Sensor
//#define DOOR_PIN                            45  // HM1 Connector