/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
 *
 */
#pragma once

/**
 * 3DRAG (and K8200 / K8400) Arduino Mega with RAMPS v1.4 pin assignments
 */

#ifndef BOARD_INFO_NAME
  #define BOARD_INFO_NAME "3Drag"
#endif

#ifndef DEFAULT_MACHINE_NAME
  #define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
#endif

#ifndef DEFAULT_SOURCE_CODE_URL
  #define DEFAULT_SOURCE_CODE_URL "3dprint.elettronicain.it"
#endif

//
// Heaters / Fans
//
#define RAMPS_D8_PIN                           9
#define RAMPS_D9_PIN                           8
#define MOSFET_D_PIN                          12

#ifndef CASE_LIGHT_PIN
  #define CASE_LIGHT_PIN                      -1  // Hardware PWM but one is not available on expansion header
#endif

#include "pins_RAMPS.h"

//
// Limit Switches
//
#undef Z_MAX_PIN

//
// Steppers
//
#undef Z_ENABLE_PIN
#define Z_ENABLE_PIN                          63

//
// Heaters / Fans
//
#define HEATER_2_PIN                           6

//
// Misc. Functions
//
#undef SDSS
#define SDSS                                  25

#undef SD_DETECT_PIN
#define SD_DETECT_PIN                         53

//
// LCD / Controller
//
#if IS_ULTRA_LCD && IS_NEWPANEL
  #undef BEEPER_PIN

  #undef LCD_PINS_RS
  #undef LCD_PINS_ENABLE
  #undef LCD_PINS_D4
  #undef LCD_PINS_D5
  #undef LCD_PINS_D6
  #undef LCD_PINS_D7
  #define LCD_PINS_RS                         27
  #define LCD_PINS_ENABLE                     29
  #define LCD_PINS_D4                         37
  #define LCD_PINS_D5                         35
  #define LCD_PINS_D6                         33
  #define LCD_PINS_D7                         31

  // Buttons
  #undef BTN_EN1
  #undef BTN_EN2
  #undef BTN_ENC
  #define BTN_EN1                             16
  #define BTN_EN2                             17
  #define BTN_ENC                             23

#else

  #define BEEPER_PIN                          33

#endif // IS_ULTRA_LCD && IS_NEWPANEL

/**
 *  M3/M4/M5 - Spindle/Laser Control
 *
 *  If you want to control the speed of your spindle then you'll have
 *  have to sacrifce the Extruder and pull some signals off the Z stepper
 *  driver socket.
 *
 *  The following assumes:
 *   - the Z stepper driver socket is empty
 *   - the extruder driver socket has a driver board plugged into it
 *   - the Z stepper wires are attached the the extruder connector
 *
 *  If you want to keep the extruder AND don't have a LCD display then
 *  you can still control the power on/off and spindle direction.
 *
 *  Where to get spindle signals
 *
 *      stepper signal           socket name       socket name
 *                                          -------
 *       SPINDLE_LASER_ENA_PIN    /ENABLE  O|     |O  VMOT
 *                                    MS1  O|     |O  GND
 *                                    MS2  O|     |O  2B
 *                                    MS3  O|     |O  2A
 *                                 /RESET  O|     |O  1A
 *                                 /SLEEP  O|     |O  1B
 *          SPINDLE_LASER_PWM_PIN    STEP  O|     |O  VDD
 *                SPINDLE_DIR_PIN     DIR  O|     |O  GND
 *                                          -------
 *
 *  Note: Socket names vary from vendor to vendor
 */
#undef SPINDLE_LASER_PWM_PIN                      // Definitions in pins_RAMPS.h are not good with 3DRAG
#undef SPINDLE_LASER_ENA_PIN
#undef SPINDLE_DIR_PIN

#if HAS_CUTTER
  #if !EXTRUDERS
    #undef E0_DIR_PIN
    #undef E0_ENABLE_PIN
    #undef E0_STEP_PIN
    #undef Z_DIR_PIN
    #undef Z_ENABLE_PIN
    #undef Z_STEP_PIN
    #define Z_DIR_PIN                         28
    #define Z_ENABLE_PIN                      24
    #define Z_STEP_PIN                        26
    #define SPINDLE_LASER_PWM_PIN             46  // Hardware PWM
    #define SPINDLE_LASER_ENA_PIN             62  // Pullup!
    #define SPINDLE_DIR_PIN                   48
  #elif !BOTH(IS_ULTRA_LCD, IS_NEWPANEL)          // Use expansion header if no LCD in use
    #define SPINDLE_LASER_ENA_PIN             16  // Pullup or pulldown!
    #define SPINDLE_DIR_PIN                   17
  #endif
#endif