/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once // // FYSETC F6 1.3 (and 1.4) pin assignments // #if NOT_TARGET(__AVR_ATmega2560__) #error "Oops! Select 'FYSETC F6' in 'Tools > Board.'" #endif #ifndef BOARD_INFO_NAME #define BOARD_INFO_NAME "FYSETC F6 1.3" #endif #define RESET_PIN 30 #define SPI_FLASH_CS 83 // // Servos // #define SERVO0_PIN 13 #define SERVO1_PIN 11 // (PS_ON_PIN) #define SERVO2_PIN 10 // (FIL_RUNOUT_PIN) #define SERVO3_PIN 4 // (RGB_LED_G_PIN) // // Limit Switches // #define X_MIN_PIN 63 #define X_MAX_PIN 64 #define Y_MIN_PIN 14 #define Y_MAX_PIN 15 #define Z_MIN_PIN 12 #ifndef Z_MAX_PIN #define Z_MAX_PIN 9 #endif #ifndef FIL_RUNOUT_PIN #define FIL_RUNOUT_PIN SERVO2_PIN #endif // // Z Probe (when not Z_MIN_PIN) // #ifndef Z_MIN_PROBE_PIN #define Z_MIN_PROBE_PIN 9 // Servos pin #endif // // Steppers // #define X_STEP_PIN 54 #define X_DIR_PIN 55 #define X_ENABLE_PIN 38 #ifndef X_CS_PIN #define X_CS_PIN 70 #endif #define Y_STEP_PIN 60 #define Y_DIR_PIN 61 #define Y_ENABLE_PIN 56 #ifndef Y_CS_PIN #define Y_CS_PIN 39 #endif #define Z_STEP_PIN 43 #define Z_DIR_PIN 48 #define Z_ENABLE_PIN 58 #ifndef Z_CS_PIN #define Z_CS_PIN 74 #endif #define E0_STEP_PIN 26 #define E0_DIR_PIN 28 #define E0_ENABLE_PIN 24 #ifndef E0_CS_PIN #define E0_CS_PIN 47 #endif #define E1_STEP_PIN 36 #define E1_DIR_PIN 34 #define E1_ENABLE_PIN 30 #ifndef E1_CS_PIN #define E1_CS_PIN 32 #endif #define E2_STEP_PIN 59 #define E2_DIR_PIN 57 #define E2_ENABLE_PIN 40 #ifndef E2_CS_PIN #define E2_CS_PIN 42 #endif // // Sensorless homing DIAG pin is not directly connected to the MCU. Close // the jumper next to the limit switch socket when using sensorless homing. // #if HAS_TMC_UART /** * TMC2208/TMC2209 stepper drivers * * Software serial communication pins. * At the moment, F6 rx pins are not pc interrupt pins */ #ifndef X_SERIAL_RX_PIN #define X_SERIAL_RX_PIN -1 // 71 #endif #ifndef X_SERIAL_TX_PIN #define X_SERIAL_TX_PIN 72 #endif #ifndef Y_SERIAL_RX_PIN #define Y_SERIAL_RX_PIN -1 // 73 #endif #ifndef Y_SERIAL_TX_PIN #define Y_SERIAL_TX_PIN 75 #endif #ifndef Z_SERIAL_RX_PIN #define Z_SERIAL_RX_PIN -1 // 78 #endif #ifndef Z_SERIAL_TX_PIN #define Z_SERIAL_TX_PIN 79 #endif #ifndef E0_SERIAL_RX_PIN #define E0_SERIAL_RX_PIN -1 // 76 #endif #ifndef E0_SERIAL_TX_PIN #define E0_SERIAL_TX_PIN 77 #endif #ifndef E1_SERIAL_RX_PIN #define E1_SERIAL_RX_PIN -1 // 80 #endif #ifndef E1_SERIAL_TX_PIN #define E1_SERIAL_TX_PIN 81 #endif #ifndef E2_SERIAL_RX_PIN #define E2_SERIAL_RX_PIN -1 // 22 #endif #ifndef E2_SERIAL_TX_PIN #define E2_SERIAL_TX_PIN 82 #endif #endif // // Temperature Sensors // #define TEMP_0_PIN 12 // Analog Input #define TEMP_1_PIN 13 // Analog Input #define TEMP_2_PIN 14 // Analog Input #define TEMP_BED_PIN 15 // Analog Input #ifndef FILWIDTH_PIN #define FILWIDTH_PIN 9 // Analog Input on X+ endstop #endif // // Heaters / Fans // #define HEATER_0_PIN 5 #define HEATER_1_PIN 6 #define HEATER_2_PIN 7 #define HEATER_BED_PIN 8 #define FAN_PIN 44 #define FAN1_PIN 45 #define FAN2_PIN 46 // // Misc. Functions // #define SDSS 53 #define LED_PIN 13 #define KILL_PIN 41 #ifndef PS_ON_PIN #define PS_ON_PIN SERVO1_PIN #endif /** * ----- ----- * 5V/D41 | · · | GND 5V | · · | GND * RESET | · · | D49 (SD_DETECT) (LCD_D7) D29 | · · | D27 (LCD_D6) * (MOSI) D51 | · · D33 (BTN_EN2) (LCD_D5) D25 | · · D23 (LCD_D4) * (SD_SS) D53 | · · | D31 (BTN_EN1) (LCD_RS) D16 | · · | D17 (LCD_EN) * (SCK) D52 | · · | D50 (MISO) (BTN_ENC) D35 | · · | D37 (BEEPER) * ----- ----- * EXP2 EXP1 */ // // LCDs and Controllers // #define SD_DETECT_PIN 49 #if ENABLED(FYSETC_242_OLED_12864) #define BTN_EN1 37 #define BTN_EN2 29 #define BTN_ENC 35 #define BEEPER_PIN 31 #define LCD_PINS_DC 25 #define LCD_PINS_RS 33 #define DOGLCD_CS 16 #define DOGLCD_MOSI 23 #define DOGLCD_SCK 17 #define DOGLCD_A0 LCD_PINS_DC #undef KILL_PIN #define NEOPIXEL_PIN 27 #else #define BEEPER_PIN 37 #if ENABLED(FYSETC_MINI_12864) // // See https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8 // #define DOGLCD_A0 16 #define DOGLCD_CS 17 #if ENABLED(FYSETC_GENERIC_12864_1_1) #define LCD_BACKLIGHT_PIN 27 #endif #define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally. // Seems to work best if left open. #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) #ifndef RGB_LED_R_PIN #define RGB_LED_R_PIN 25 #endif #ifndef RGB_LED_G_PIN #define RGB_LED_G_PIN 27 #endif #ifndef RGB_LED_B_PIN #define RGB_LED_B_PIN 29 #endif #elif ENABLED(FYSETC_MINI_12864_2_1) #define NEOPIXEL_PIN 25 #endif #elif HAS_MARLINUI_U8GLIB || HAS_MARLINUI_HD44780 #define LCD_PINS_RS 16 #define LCD_PINS_ENABLE 17 #define LCD_PINS_D4 23 #define LCD_PINS_D5 25 #define LCD_PINS_D6 27 #define LCD_PINS_D7 29 #if ENABLED(MKS_MINI_12864) #define DOGLCD_CS 25 #define DOGLCD_A0 27 #endif #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder #endif #endif #if IS_NEWPANEL #define BTN_EN1 31 #define BTN_EN2 33 #define BTN_ENC 35 #endif #endif #ifndef RGB_LED_R_PIN #define RGB_LED_R_PIN 3 #endif #ifndef RGB_LED_G_PIN #define RGB_LED_G_PIN 4 #endif #ifndef RGB_LED_B_PIN #define RGB_LED_B_PIN 9 #endif #ifndef RGB_LED_W_PIN #define RGB_LED_W_PIN -1 #endif