Initial commit

1 files changed, 260 insertions, 0 deletions

diff --git a/Marlin/src/pins/sam/pins_RURAMPS4D_13.h b/Marlin/src/pins/sam/pins_RURAMPS4D_13.h
new file mode 100644
index 0000000..6ec10f6
--- /dev/null
+++ b/Marlin/src/pins/sam/pins_RURAMPS4D_13.h
@@ -0,0 +1,260 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ * Ported sys0724 & Vynt
+ */
+
+/**
+ * Arduino Mega? or Due with RuRAMPS4DUE pin assignments
+ *
+ * Applies to the following boards:
+ *  RURAMPS4DUE      (Hotend0, Hotend1, Hotend2, Fan0, Fan1, Bed)
+ *
+ *  Differences between
+ *     RADDS | RuRAMPS4DUE
+ *           |
+ */
+
+#if NOT_TARGET(__SAM3X8E__)
+  #error "Oops! Select 'Arduino Due' in 'Tools > Board.'"
+#endif
+
+#define BOARD_INFO_NAME "RuRAMPS4Due v1.3"
+
+//
+// Servos
+//
+#define SERVO0_PIN                             5
+#define SERVO1_PIN                             3
+
+//
+// Limit Switches
+//
+#define X_MIN_PIN                             45
+#define X_MAX_PIN                             39
+#define Y_MIN_PIN                             46
+#define Y_MAX_PIN                             41
+#define Z_MIN_PIN                             47
+#define Z_MAX_PIN                             43
+
+//
+// Z Probe (when not Z_MIN_PIN)
+//
+#ifndef Z_MIN_PROBE_PIN
+  #define Z_MIN_PROBE_PIN                     49
+#endif
+
+//
+// Steppers
+//
+#define X_STEP_PIN                            37  // Support Extension Board
+#define X_DIR_PIN                             36
+#define X_ENABLE_PIN                          31
+#ifndef X_CS_PIN
+  #define X_CS_PIN                            38
+#endif
+
+#define Y_STEP_PIN                            32  // Support Extension Board
+#define Y_DIR_PIN                             35
+#define Y_ENABLE_PIN                          31
+#ifndef Y_CS_PIN
+  #define Y_CS_PIN                            34
+#endif
+
+#define Z_STEP_PIN                            30  // Support Extension Board
+#define Z_DIR_PIN                              2
+#define Z_ENABLE_PIN                          31
+#ifndef Z_CS_PIN
+  #define Z_CS_PIN                            10
+#endif
+
+#define E0_STEP_PIN                           29
+#define E0_DIR_PIN                            28
+#define E0_ENABLE_PIN                         33
+#ifndef E0_CS_PIN
+  #define E0_CS_PIN                           14
+#endif
+
+#define E1_STEP_PIN                           22
+#define E1_DIR_PIN                            24
+#define E1_ENABLE_PIN                         26
+#ifndef E1_CS_PIN
+  #define E1_CS_PIN                           15
+#endif
+
+#define E2_STEP_PIN                           25
+#define E2_DIR_PIN                            23
+#define E2_ENABLE_PIN                         27
+#ifndef E2_CS_PIN
+  #define E2_CS_PIN                           61
+#endif
+
+#if HAS_CUSTOM_PROBE_PIN
+  #define Z_MIN_PROBE_PIN                     49
+#endif
+
+#if HAS_FILAMENT_SENSOR
+  #ifndef FIL_RUNOUT_PIN
+    #define FIL_RUNOUT_PIN             Y_MIN_PIN
+  #endif
+#endif
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN                          13
+#define HEATER_1_PIN                          12
+#define HEATER_2_PIN                          11
+#define HEATER_BED_PIN                         7  // BED H1
+
+#define FAN_PIN                                9
+#define FAN1_PIN                               8
+#define CONTROLLER_FAN_PIN                    -1
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN                             0  // ANALOG A0
+#define TEMP_1_PIN                             1  // ANALOG A1
+#define TEMP_2_PIN                             2  // ANALOG A2
+#define TEMP_3_PIN                             3  // ANALOG A3
+#define TEMP_BED_PIN                           4  // ANALOG A4
+
+// The thermocouple uses Analog pins
+#if ENABLED(VER_WITH_THERMOCOUPLE)                // Defined in Configuration.h
+  #define TEMP_4_PIN                           5  // A5
+  #define TEMP_5_PIN                           6  // A6 (Marlin 2.0 not support)
+#endif
+
+// SPI for Max6675 or Max31855 Thermocouple
+/*
+#if DISABLED(SDSUPPORT)
+  #define MAX6675_SS_PIN                      53
+#else
+  #define MAX6675_SS_PIN                      49
+#endif
+*/
+
+//
+// Misc. Functions
+//
+#define SDSS                                   4  // 4,10,52 if using HW SPI.
+#define LED_PIN                               -1  // 13 - HEATER_0_PIN
+#define PS_ON_PIN                             -1  // 65
+
+// MKS TFT / Nextion Use internal USART-1
+#define TFT_LCD_MODULE_COM                     1
+#define TFT_LCD_MODULE_BAUDRATE              115200
+
+// ESP WiFi Use internal USART-2
+#define ESP_WIFI_MODULE_COM                    2
+#define ESP_WIFI_MODULE_BAUDRATE             115200
+#define ESP_WIFI_MODULE_RESET_PIN             -1
+#define PIGGY_GPIO_PIN                        -1
+
+//
+// EEPROM
+//
+#define MARLIN_EEPROM_SIZE                0x8000  // 32Kb (24lc256)
+#define I2C_EEPROM                                // EEPROM on I2C-0
+//#define EEPROM_SD                               // EEPROM on SDCARD
+//#define SPI_EEPROM                              // EEPROM on SPI-0
+//#define SPI_CHAN_EEPROM1        ?
+//#define SPI_EEPROM1_CS          ?
+// 2K EEPROM
+//#define SPI_EEPROM2_CS          ?
+// 32Mb FLASH
+//#define SPI_FLASH_CS            ?
+
+//
+// LCD / Controller
+//
+#if HAS_WIRED_LCD
+
+  #if ANY(RADDS_DISPLAY, IS_RRD_SC, IS_RRD_FG_SC)
+    #define BEEPER_PIN                        62
+    #define LCD_PINS_D4                       48
+    #define LCD_PINS_D5                       50
+    #define LCD_PINS_D6                       52
+    #define LCD_PINS_D7                       53
+    #define SD_DETECT_PIN                     51
+  #endif
+
+  #if EITHER(RADDS_DISPLAY, IS_RRD_SC)
+
+    #define LCD_PINS_RS                       63
+    #define LCD_PINS_ENABLE                   64
+
+  #elif IS_RRD_FG_SC
+
+    #define LCD_PINS_RS                       52
+    #define LCD_PINS_ENABLE                   53
+
+  #elif HAS_U8GLIB_I2C_OLED
+
+    #define BEEPER_PIN                        62
+    #define LCD_SDSS                          10
+    #define SD_DETECT_PIN                     51
+
+  #elif ENABLED(FYSETC_MINI_12864)
+
+    #define BEEPER_PIN                        62
+    #define DOGLCD_CS                         64
+    #define DOGLCD_A0                         63
+
+    //#define FORCE_SOFT_SPI                      // Use this if default of hardware SPI causes display problems
+                                                  //   results in LCD soft SPI mode 3, SD soft SPI mode 0
+
+    #define LCD_RESET_PIN                     48  // Must be high or open for LCD to operate normally.
+
+    #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
+      #ifndef RGB_LED_R_PIN
+        #define RGB_LED_R_PIN                 50  // D5
+      #endif
+      #ifndef RGB_LED_G_PIN
+        #define RGB_LED_G_PIN                 52  // D6
+      #endif
+      #ifndef RGB_LED_B_PIN
+        #define RGB_LED_B_PIN                 53  // D7
+      #endif
+    #elif ENABLED(FYSETC_MINI_12864_2_1)
+      #define NEOPIXEL_PIN                    50  // D5
+    #endif
+
+  #elif ENABLED(MKS_MINI_12864)
+
+    #define DOGLCD_A0                         52
+    #define DOGLCD_CS                         50
+
+    #define SD_DETECT_PIN                     51
+
+  #endif
+
+  #if IS_NEWPANEL
+    #define BTN_EN1                           44
+    #define BTN_EN2                           42
+    #define BTN_ENC                           40
+  #endif
+
+  #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
+    #define BTN_ENC_EN               LCD_PINS_D7  // Detect the presence of the encoder
+  #endif
+
+#endif // HAS_WIRED_LCD