diff options
| author | Georgiy Bondarenko <69736697+nehilo@users.noreply.github.com> | 2021-03-04 20:54:23 +0300 |
|---|---|---|
| committer | Georgiy Bondarenko <69736697+nehilo@users.noreply.github.com> | 2021-03-04 20:54:23 +0300 |
| commit | e8701195e66f2d27ffe17fb514eae8173795aaf7 (patch) | |
| tree | 9f519c4abf6556b9ae7190a6210d87ead1dfadde /config/MKS Robin nano v3.0/Config example for suport usb-disk/Config example for Ender3(4988)/Configuration.h | |
| download | kp3s-lgvl-e8701195e66f2d27ffe17fb514eae8173795aaf7.tar.xz kp3s-lgvl-e8701195e66f2d27ffe17fb514eae8173795aaf7.zip | |
Initial commit
Diffstat (limited to 'config/MKS Robin nano v3.0/Config example for suport usb-disk/Config example for Ender3(4988)/Configuration.h')
| -rw-r--r-- | config/MKS Robin nano v3.0/Config example for suport usb-disk/Config example for Ender3(4988)/Configuration.h | 2611 |
1 files changed, 2611 insertions, 0 deletions
diff --git a/config/MKS Robin nano v3.0/Config example for suport usb-disk/Config example for Ender3(4988)/Configuration.h b/config/MKS Robin nano v3.0/Config example for suport usb-disk/Config example for Ender3(4988)/Configuration.h new file mode 100644 index 0000000..616aefe --- /dev/null +++ b/config/MKS Robin nano v3.0/Config example for suport usb-disk/Config example for Ender3(4988)/Configuration.h @@ -0,0 +1,2611 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + */ +#define CONFIGURATION_H_VERSION 020008 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * https://reprap.org/wiki/Calibration + * https://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * https://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * https://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * https://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer, start with one of the configuration files in the config/examples/delta directory +// from https://github.com/MarlinFirmware/Configurations/branches/all and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer, start with one of the configuration files in the config/examples/SCARA directory +// from https://github.com/MarlinFirmware/Configurations/branches/all and customize for your machine. +// + +// @section info + +// Author info of this build printed to the host during boot and M115 +#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. +//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes) + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respectfully request that you retain the unmodified Marlin boot screen. + */ + +// Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION ** +#define SHOW_BOOTSCREEN + +// Show the bitmap in Marlin/_Bootscreen.h on startup. +//#define SHOW_CUSTOM_BOOTSCREEN + +// Show the bitmap in Marlin/_Statusscreen.h on the status screen. +//#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT -1 + +/** + * Select a secondary serial port on the board to use for communication with the host. + * Currently Ethernet (-2) is only supported on Teensy 4.1 boards. + * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +//#define SERIAL_PORT_2 -1 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 250000 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// Choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_MKS_ROBIN_NANO_V3 +#endif + +// Name displayed in the LCD "Ready" message and Info menu +//#define CUSTOM_MACHINE_NAME "3D Printer" + +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like https://www.uuidgenerator.net/version4 +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[0, 1, 2, 3, 4, 5, 6, 7, 8] +#define EXTRUDERS 1 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +// Save and restore temperature and fan speed on tool-change. +// Set standby for the unselected tool with M104/106/109 T... +#if ENABLED(SINGLENOZZLE) + //#define SINGLENOZZLE_STANDBY_TEMP + //#define SINGLENOZZLE_STANDBY_FAN +#endif + +/** + * Multi-Material Unit + * Set to one of these predefined models: + * + * PRUSA_MMU1 : Průša MMU1 (The "multiplexer" version) + * PRUSA_MMU2 : Průša MMU2 + * PRUSA_MMU2S : Průša MMU2S (Requires MK3S extruder with motion sensor, EXTRUDERS = 5) + * SMUFF_EMU_MMU2 : Technik Gegg SMUFF (Průša MMU2 emulation mode) + * SMUFF_EMU_MMU2S : Technik Gegg SMUFF (Průša MMU2S emulation mode) + * + * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails. + * See additional options in Configuration_adv.h. + */ +//#define MMU_MODEL PRUSA_MMU2 + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism using movements and no solenoid + * + * project : https://www.thingiverse.com/thing:3080893 + * movements : https://youtu.be/0xCEiG9VS3k + * https://youtu.be/Bqbcs0CU2FE + */ +//#define MAGNETIC_PARKING_EXTRUDER + +#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #if ENABLED(PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined. + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define MPE_FAST_SPEED 9000 // (mm/min) Speed for travel before last distance point + #define MPE_SLOW_SPEED 4500 // (mm/min) Speed for last distance travel to park and couple + #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point + #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling + + #endif + +#endif + +/** + * Switching Toolhead + * + * Support for swappable and dockable toolheads, such as + * the E3D Tool Changer. Toolheads are locked with a servo. + */ +//#define SWITCHING_TOOLHEAD + +/** + * Magnetic Switching Toolhead + * + * Support swappable and dockable toolheads with a magnetic + * docking mechanism using movement and no servo. + */ +//#define MAGNETIC_SWITCHING_TOOLHEAD + +/** + * Electromagnetic Switching Toolhead + * + * Parking for CoreXY / HBot kinematics. + * Toolheads are parked at one edge and held with an electromagnet. + * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 + */ +//#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD + +#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock + #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis + #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders + #if ENABLED(SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector + #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock + #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/min) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/min) Extruder retract feedrate + #endif + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching + #endif +#endif + +/** + * "Mixing Extruder" + * - Adds G-codes M163 and M164 to set and "commit" the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools. + * - This implementation supports up to two mixing extruders. + * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands + //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD + #if ENABLED(GRADIENT_MIX) + //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias + #endif +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle + +// @section machine + +/** + * Power Supply Control + * + * Enable and connect the power supply to the PS_ON_PIN. + * Specify whether the power supply is active HIGH or active LOW. + */ +//#define PSU_CONTROL +//#define PSU_NAME "Power Supply" + +#if ENABLED(PSU_CONTROL) + #define PSU_ACTIVE_STATE LOW // Set 'LOW' for ATX, 'HIGH' for X-Box + + //#define PSU_DEFAULT_OFF // Keep power off until enabled directly with M80 + //#define PSU_POWERUP_DELAY 250 // (ms) Delay for the PSU to warm up to full power + + //#define PSU_POWERUP_GCODE "M355 S1" // G-code to run after power-on (e.g., case light on) + //#define PSU_POWEROFF_GCODE "M355 S0" // G-code to run before power-off (e.g., case light off) + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define AUTO_POWER_CHAMBER_FAN + //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU if any extruder is over this temperature + //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU if the chamber is over this temperature + #define POWER_TIMEOUT 30 // (s) Turn off power if the machine is idle for this duration + //#define POWER_OFF_DELAY 60 // (s) Delay of poweroff after M81 command. Useful to let fans run for extra time. + #endif +#endif + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== +// @section temperature + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1) + * -3 : thermocouple with MAX31855 (only for sensors 0-1) + * -2 : thermocouple with MAX6675 (only for sensors 0-1) + * -4 : thermocouple with AD8495 + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table for MEGA) + * 332 : (3.3V scaled thermistor 1 table for DUE) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup) + * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327 + * 20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage. + * NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21. + * 21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply. + * NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C. + * 22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB) + * 23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB) + * 30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup) + * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 67 : 450C thermistor from SliceEngineering + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * 99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines) + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup (E3D) + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * 1000 : Custom - Specify parameters in Configuration_adv.h + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + */ +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_5 0 +#define TEMP_SENSOR_6 0 +#define TEMP_SENSOR_7 0 +#define TEMP_SENSOR_BED 1 +#define TEMP_SENSOR_PROBE 0 +#define TEMP_SENSOR_CHAMBER 0 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Resistor values when using MAX31865 sensors (-5) on TEMP_SENSOR_0 / 1 +//#define MAX31865_SENSOR_OHMS_0 100 // (Ω) Typically 100 or 1000 (PT100 or PT1000) +//#define MAX31865_CALIBRATION_OHMS_0 430 // (Ω) Typically 430 for AdaFruit PT100; 4300 for AdaFruit PT1000 +//#define MAX31865_SENSOR_OHMS_1 100 +//#define MAX31865_CALIBRATION_OHMS_1 430 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +#define TEMP_RESIDENCY_TIME 4 // (seconds) Time to wait for hotend to "settle" in M109 +#define TEMP_WINDOW 4 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_HYSTERESIS 4 // (°C) Temperature proximity considered "close enough" to the target + +#define TEMP_BED_RESIDENCY_TIME 4 // (seconds) Time to wait for bed to "settle" in M190 +#define TEMP_BED_WINDOW 4 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_BED_HYSTERESIS 4 // (°C) Temperature proximity considered "close enough" to the target + +// Below this temperature the heater will be switched off +// because it probably indicates a broken thermistor wire. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define HEATER_5_MINTEMP 5 +#define HEATER_6_MINTEMP 5 +#define HEATER_7_MINTEMP 5 +#define BED_MINTEMP 5 + +// Above this temperature the heater will be switched off. +// This can protect components from overheating, but NOT from shorts and failures. +// (Use MINTEMP for thermistor short/failure protection.) +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define HEATER_5_MAXTEMP 275 +#define HEATER_6_MAXTEMP 275 +#define HEATER_7_MAXTEMP 275 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop + +#if ENABLED(PIDTEMP) + //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + + #if ENABLED(PID_PARAMS_PER_HOTEND) + // Specify between 1 and HOTENDS values per array. + // If fewer than EXTRUDER values are provided, the last element will be repeated. + #define DEFAULT_Kp_LIST { 22.20, 22.20 } + #define DEFAULT_Ki_LIST { 1.08, 1.08 } + #define DEFAULT_Kd_LIST { 114.00, 114.00 } + #else + #define DEFAULT_Kp 22.20 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114.00 + #endif +#endif // PIDTEMP + +//=========================================================================== +//====================== PID > Bed Temperature Control ====================== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + //#define MIN_BED_POWER 0 + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +#if EITHER(PIDTEMP, PIDTEMPBED) + //#define PID_DEBUG // Sends debug data to the serial port. Use 'M303 D' to toggle activation. + //#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. +#endif + +// @section extruder + +/** + * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. + * Add M302 to set the minimum extrusion temperature and/or turn + * cold extrusion prevention on and off. + * + * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** + */ +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +/** + * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. + * Note: For Bowden Extruders make this large enough to allow load/unload. + */ +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 600 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed +#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Enable one of the options below for CoreXY, CoreXZ, or CoreYZ kinematics, +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY +//#define MARKFORGED_XY // MarkForged. See https://reprap.org/forum/read.php?152,504042 + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe. + +/** + * Stepper Drivers + * + * These settings allow Marlin to tune stepper driver timing and enable advanced options for + * stepper drivers that support them. You may also override timing options in Configuration_adv.h. + * + * A4988 is assumed for unspecified drivers. + * + * Use TMC2208/TMC2208_STANDALONE for TMC2225 drivers and TMC2209/TMC2209_STANDALONE for TMC2226 drivers. + * + * Options: A4988, A5984, DRV8825, LV8729, L6470, L6474, POWERSTEP01, + * TB6560, TB6600, TMC2100, + * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE, + * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE, + * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, + * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE + * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] + */ +#define X_DRIVER_TYPE A4988 +#define Y_DRIVER_TYPE A4988 +#define Z_DRIVER_TYPE A4988 +//#define X2_DRIVER_TYPE A4988 +//#define Y2_DRIVER_TYPE A4988 +//#define Z2_DRIVER_TYPE A4988 +//#define Z3_DRIVER_TYPE A4988 +//#define Z4_DRIVER_TYPE A4988 +#define E0_DRIVER_TYPE A4988 +//#define E1_DRIVER_TYPE A4988 +//#define E2_DRIVER_TYPE A4988 +//#define E3_DRIVER_TYPE A4988 +//#define E4_DRIVER_TYPE A4988 +//#define E5_DRIVER_TYPE A4988 +//#define E6_DRIVER_TYPE A4988 +//#define E7_DRIVER_TYPE A4988 + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +/** + * Endstop Noise Threshold + * + * Enable if your probe or endstops falsely trigger due to noise. + * + * - Higher values may affect repeatability or accuracy of some bed probes. + * - To fix noise install a 100nF ceramic capacitor in parallel with the switch. + * - This feature is not required for common micro-switches mounted on PCBs + * based on the Makerbot design, which already have the 100nF capacitor. + * + * :[2,3,4,5,6,7] + */ +//#define ENDSTOP_NOISE_THRESHOLD 2 + +// Check for stuck or disconnected endstops during homing moves. +//#define DETECT_BROKEN_ENDSTOP + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2...]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 133 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2...]] + */ +#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } + +//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2 +#if ENABLED(LIMITED_MAX_FR_EDITING) + #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits +#endif + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2...]] + */ +#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 } + +//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2 +#if ENABLED(LIMITED_MAX_ACCEL_EDITING) + #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits +#endif + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Default Jerk limits (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +//#define CLASSIC_JERK +#if ENABLED(CLASSIC_JERK) + #define DEFAULT_XJERK 10.0 + #define DEFAULT_YJERK 10.0 + #define DEFAULT_ZJERK 0.3 + + //#define TRAVEL_EXTRA_XYJERK 0.0 // Additional jerk allowance for all travel moves + + //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2 + #if ENABLED(LIMITED_JERK_EDITING) + #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits + #endif +#endif + +#define DEFAULT_EJERK 5.0 // May be used by Linear Advance + +/** + * Junction Deviation Factor + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * https://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ +#if DISABLED(CLASSIC_JERK) + #define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge + #define JD_HANDLE_SMALL_SEGMENTS // Use curvature estimation instead of just the junction angle + // for small segments (< 1mm) with large junction angles (> 135°). +#endif + +/** + * S-Curve Acceleration + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +//#define S_CURVE_ACCELERATION + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See https://marlinfw.org/docs/configuration/probes.html +// + +/** + * Enable this option for a probe connected to the Z-MIN pin. + * The probe replaces the Z-MIN endstop and is used for Z homing. + * (Automatically enables USE_PROBE_FOR_Z_HOMING.) + */ +//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// Force the use of the probe for Z-axis homing +//#define USE_PROBE_FOR_Z_HOMING + +/** + * Z_MIN_PROBE_PIN + * + * Define this pin if the probe is not connected to Z_MIN_PIN. + * If not defined the default pin for the selected MOTHERBOARD + * will be used. Most of the time the default is what you want. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + */ +//#define Z_MIN_PROBE_PIN PC4 // Pin 32 is the RAMPS default + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY +//#define MANUAL_PROBE_START_Z 0.2 + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Use the nozzle as the probe, as with a conductive + * nozzle system or a piezo-electric smart effector. + */ +//#define NOZZLE_AS_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH + +/** + * Touch-MI Probe by hotends.fr + * + * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed. + * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is + * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. + * + * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, + * and a minimum Z_HOMING_HEIGHT of 10. + */ +//#define TOUCH_MI_PROBE +#if ENABLED(TOUCH_MI_PROBE) + #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts + //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed + //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu) +#endif + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. +//#define RACK_AND_PINION_PROBE +#if ENABLED(RACK_AND_PINION_PROBE) + #define Z_PROBE_DEPLOY_X X_MIN_POS + #define Z_PROBE_RETRACT_X X_MAX_POS +#endif + +// Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J +// When the pin is defined you can use M672 to set/reset the probe sensivity. +//#define DUET_SMART_EFFECTOR +#if ENABLED(DUET_SMART_EFFECTOR) + #define SMART_EFFECTOR_MOD_PIN -1 // Connect a GPIO pin to the Smart Effector MOD pin +#endif + +/** + * Use StallGuard2 to probe the bed with the nozzle. + * Requires stallGuard-capable Trinamic stepper drivers. + * CAUTION: This can damage machines with Z lead screws. + * Take extreme care when setting up this feature. + */ +//#define SENSORLESS_PROBING + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Nozzle-to-Probe offsets { X, Y, Z } + * + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of + * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset + * - For the Z offset use your best known value and adjust at runtime. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. + * + * Assuming the typical work area orientation: + * - Probe to RIGHT of the Nozzle has a Positive X offset + * - Probe to LEFT of the Nozzle has a Negative X offset + * - Probe in BACK of the Nozzle has a Positive Y offset + * - Probe in FRONT of the Nozzle has a Negative Y offset + * + * Some examples: + * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, -1 } // Example "1" + * #define NOZZLE_TO_PROBE_OFFSET {-10, 5, -1 } // Example "2" + * #define NOZZLE_TO_PROBE_OFFSET { 5, -5, -1 } // Example "3" + * #define NOZZLE_TO_PROBE_OFFSET {-15,-10, -1 } // Example "4" + * + * +-- BACK ---+ + * | [+] | + * L | 1 | R <-- Example "1" (right+, back+) + * E | 2 | I <-- Example "2" ( left-, back+) + * F |[-] N [+]| G <-- Nozzle + * T | 3 | H <-- Example "3" (right+, front-) + * | 4 | T <-- Example "4" ( left-, front-) + * | [-] | + * O-- FRONT --+ + */ +#define NOZZLE_TO_PROBE_OFFSET { -40, -14, -2 } + +// Most probes should stay away from the edges of the bed, but +// with NOZZLE_AS_PROBE this can be negative for a wider probing area. +#define PROBING_MARGIN 30 + +// X and Y axis travel speed (mm/min) between probes +#define XY_PROBE_SPEED (133*60) + +// Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST (4*60) + +// Feedrate (mm/min) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +/** + * Probe Activation Switch + * A switch indicating proper deployment, or an optical + * switch triggered when the carriage is near the bed. + */ +//#define PROBE_ACTIVATION_SWITCH +#if ENABLED(PROBE_ACTIVATION_SWITCH) + #define PROBE_ACTIVATION_SWITCH_STATE LOW // State indicating probe is active + //#define PROBE_ACTIVATION_SWITCH_PIN PC6 // Override default pin +#endif + +/** + * Tare Probe (determine zero-point) prior to each probe. + * Useful for a strain gauge or piezo sensor that needs to factor out + * elements such as cables pulling on the carriage. + */ +//#define PROBE_TARE +#if ENABLED(PROBE_TARE) + #define PROBE_TARE_TIME 200 // (ms) Time to hold tare pin + #define PROBE_TARE_DELAY 200 // (ms) Delay after tare before + #define PROBE_TARE_STATE HIGH // State to write pin for tare + //#define PROBE_TARE_PIN PA5 // Override default pin + #if ENABLED(PROBE_ACTIVATION_SWITCH) + //#define PROBE_TARE_ONLY_WHILE_INACTIVE // Fail to tare/probe if PROBE_ACTIVATION_SWITCH is active + #endif +#endif + +/** + * Multiple Probing + * + * You may get improved results by probing 2 or more times. + * With EXTRA_PROBING the more atypical reading(s) will be disregarded. + * + * A total of 2 does fast/slow probes with a weighted average. + * A total of 3 or more adds more slow probes, taking the average. + */ +//#define MULTIPLE_PROBING 2 +//#define EXTRA_PROBING 1 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +//#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// Before deploy/stow pause for user confirmation +//#define PAUSE_BEFORE_DEPLOY_STOW +#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW) + //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe +#endif + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disable axis steppers immediately when they're not being stepped. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// Turn off the display blinking that warns about possible accuracy reduction +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // Disable the extruder when not stepping +#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR false +#define INVERT_Y_DIR false +#define INVERT_Z_DIR true + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR false +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false +#define INVERT_E5_DIR false +#define INVERT_E6_DIR false +#define INVERT_E7_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed. Also enable HOME_AFTER_DEACTIVATE for extra safety. +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated. Also enable NO_MOTION_BEFORE_HOMING for extra safety. +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding. + +//#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 220 +#define Y_BED_SIZE 220 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 250 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * IMPORTANT: Runout will only trigger if Marlin is aware that a print job is running. + * Marlin knows a print job is running when: + * 1. Running a print job from media started with M24. + * 2. The Print Job Timer has been started with M75. + * 3. The heaters were turned on and PRINTJOB_TIMER_AUTOSTART is enabled. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500. + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + + #define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + + // Override individually if the runout sensors vary + //#define FIL_RUNOUT1_STATE LOW + //#define FIL_RUNOUT1_PULLUP + //#define FIL_RUNOUT1_PULLDOWN + + //#define FIL_RUNOUT2_STATE LOW + //#define FIL_RUNOUT2_PULLUP + //#define FIL_RUNOUT2_PULLDOWN + + //#define FIL_RUNOUT3_STATE LOW + //#define FIL_RUNOUT3_PULLUP + //#define FIL_RUNOUT3_PULLDOWN + + //#define FIL_RUNOUT4_STATE LOW + //#define FIL_RUNOUT4_PULLUP + //#define FIL_RUNOUT4_PULLDOWN + + //#define FIL_RUNOUT5_STATE LOW + //#define FIL_RUNOUT5_PULLUP + //#define FIL_RUNOUT5_PULLDOWN + + //#define FIL_RUNOUT6_STATE LOW + //#define FIL_RUNOUT6_PULLUP + //#define FIL_RUNOUT6_PULLDOWN + + //#define FIL_RUNOUT7_STATE LOW + //#define FIL_RUNOUT7_PULLUP + //#define FIL_RUNOUT7_PULLDOWN + + //#define FIL_RUNOUT8_STATE LOW + //#define FIL_RUNOUT8_PULLUP + //#define FIL_RUNOUT8_PULLDOWN + + // Set one or more commands to execute on filament runout. + // (After 'M412 H' Marlin will ask the host to handle the process.) + #define FILAMENT_RUNOUT_SCRIPT "M600" + + // After a runout is detected, continue printing this length of filament + // before executing the runout script. Useful for a sensor at the end of + // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. + //#define FILAMENT_RUNOUT_DISTANCE_MM 25 + + #ifdef FILAMENT_RUNOUT_DISTANCE_MM + // Enable this option to use an encoder disc that toggles the runout pin + // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM + // large enough to avoid false positives.) + //#define FILAMENT_MOTION_SENSOR + #endif +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +//#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable one of + * these options to restore the prior leveling state or to always enable + * leveling immediately after G28. + */ +//#define RESTORE_LEVELING_AFTER_G28 +//#define ENABLE_LEVELING_AFTER_G28 + +/** + * Auto-leveling needs preheating + */ +//#define PREHEAT_BEFORE_LEVELING +#if ENABLED(PREHEAT_BEFORE_LEVELING) + #define LEVELING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define LEVELING_BED_TEMP 50 +#endif + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z<height> + #define ENABLE_LEVELING_FADE_HEIGHT + #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT) + #define DEFAULT_LEVELING_FADE_HEIGHT 10.0 // (mm) Default fade height. + #endif + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + //#define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for G26. + #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for G26. + #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for G26. + #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for G26 XY moves. + #define G26_XY_FEEDRATE_TRAVEL 100 // (mm/s) Feedrate for G26 XY travel moves. + #define G26_RETRACT_MULTIPLIER 1.0 // G26 Q (retraction) used by default between mesh test elements. + #endif + +#endif + +#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Add a bed leveling sub-menu for ABL or MBL. + * Include a guided procedure if manual probing is enabled. + */ +//#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment + //#define MESH_EDIT_MENU // Add a menu to edit mesh points +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +//#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner + //#define LEVEL_CORNERS_USE_PROBE + #if ENABLED(LEVEL_CORNERS_USE_PROBE) + #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 + #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define LEVEL_CORNERS_AUDIO_FEEDBACK + #endif + + /** + * Corner Leveling Order + * + * Set 2 or 4 points. When 2 points are given, the 3rd is the center of the opposite edge. + * + * LF Left-Front RF Right-Front + * LB Left-Back RB Right-Back + * + * Examples: + * + * Default {LF,RB,LB,RF} {LF,RF} {LB,LF} + * LB --------- RB LB --------- RB LB --------- RB LB --------- RB + * | 4 3 | | 3 2 | | <3> | | 1 | + * | | | | | | | <3>| + * | 1 2 | | 1 4 | | 1 2 | | 2 | + * LF --------- RF LF --------- RF LF --------- RF LF --------- RF + */ + #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing. +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing + #define Z_SAFE_HOMING_Y_POINT Y_CENTER // Y point for Z homing +#endif + +// Homing speeds (mm/min) +#define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (4*60) } + +// Validate that endstops are triggered on homing moves +#define VALIDATE_HOMING_ENDSTOPS + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +/** + * EEPROM + * + * Persistent storage to preserve configurable settings across reboots. + * + * M500 - Store settings to EEPROM. + * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) + * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) + */ +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. +//#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load +#if ENABLED(EEPROM_SETTINGS) + #define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. +#endif + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_LABEL "PLA" +#define PREHEAT_1_TEMP_HOTEND 180 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 + +#define PREHEAT_2_LABEL "ABS" +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 110 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +//#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z_raise } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + //#define NOZZLE_PARK_X_ONLY // X move only is required to park + //#define NOZZLE_PARK_Y_ONLY // Y move only is required to park + #define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance + #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + */ +//#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions for each tool as { { X, Y, Z }, { X, Y, Z } } + // Dual hotend system may use { { -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }, { 420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }} + #define NOZZLE_CLEAN_START_POINT { { 30, 30, (Z_MIN_POS + 1) } } + #define NOZZLE_CLEAN_END_POINT { { 100, 60, (Z_MIN_POS + 1) } } + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Move the nozzle to the initial position after cleaning + #define NOZZLE_CLEAN_GOBACK + + // For a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z + + // For a purge/clean station mounted on the X axis + //#define NOZZLE_CLEAN_NO_Y + + // Require a minimum hotend temperature for cleaning + #define NOZZLE_CLEAN_MIN_TEMP 170 + //#define NOZZLE_CLEAN_HEATUP // Heat up the nozzle instead of skipping wipe + + // Explicit wipe G-code script applies to a G12 with no arguments. + //#define WIPE_SEQUENCE_COMMANDS "G1 X-17 Y25 Z10 F4000\nG1 Z1\nM114\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 Z15\nM400\nG0 X-10.0 Y-9.0" + +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +//#define PRINTCOUNTER +#if ENABLED(PRINTCOUNTER) + #define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print +#endif + +/** + * Password + * + * Set a numerical password for the printer which can be requested: + * + * - When the printer boots up + * - Upon opening the 'Print from Media' Menu + * - When SD printing is completed or aborted + * + * The following G-codes can be used: + * + * M510 - Lock Printer. Blocks all commands except M511. + * M511 - Unlock Printer. + * M512 - Set, Change and Remove Password. + * + * If you forget the password and get locked out you'll need to re-flash + * the firmware with the feature disabled, reset EEPROM, and (optionally) + * re-flash the firmware again with this feature enabled. + */ +//#define PASSWORD_FEATURE +#if ENABLED(PASSWORD_FEATURE) + #define PASSWORD_LENGTH 4 // (#) Number of digits (1-9). 3 or 4 is recommended + #define PASSWORD_ON_STARTUP + #define PASSWORD_UNLOCK_GCODE // Unlock with the M511 P<password> command. Disable to prevent brute-force attack. + #define PASSWORD_CHANGE_GCODE // Change the password with M512 P<old> S<new>. + //#define PASSWORD_ON_SD_PRINT_MENU // This does not prevent gcodes from running + //#define PASSWORD_AFTER_SD_PRINT_END + //#define PASSWORD_AFTER_SD_PRINT_ABORT + //#include "Configuration_Secure.h" // External file with PASSWORD_DEFAULT_VALUE +#endif + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cz, da, de, el, el_gr, es, eu, fi, fr, gl, hr, hu, it, + * jp_kana, ko_KR, nl, pl, pt, pt_br, ro, ru, sk, sv, tr, uk, vi, zh_CN, zh_TW + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el_gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'hu':'Hungarian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ro':'Romanian', 'ru':'Russian', 'sk':'Slovak', 'sv':'Swedish', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See https://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 JAPANESE + +/** + * Info Screen Style (0:Classic, 1:Průša) + * + * :[0:'Classic', 1:'Průša'] + */ +#define LCD_INFO_SCREEN_STYLE 0 + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + */ +#define SDSUPPORT + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +//#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +//#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +//#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S<frequency Hz> P<duration ms> +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +//#define LCD_FEEDBACK_FREQUENCY_HZ 5000 + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//======================== (Character-based LCDs) ========================= +//============================================================================= + +// +// RepRapDiscount Smart Controller. +// https://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// https://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// GADGETS3D G3D LCD/SD Controller +// https://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// ANET and Tronxy 20x4 Controller +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +// +// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. +// +//#define ULTRA_LCD + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//===================== (I2C and Shift-Register LCDs) ===================== +//============================================================================= + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// CONTROLLER TYPE: Shift register panels +// + +// +// 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: https://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// 3-wire SR LCD with strobe using 74HC4094 +// https://github.com/mikeshub/SailfishLCD +// Uses the code directly from Sailfish +// +//#define FF_INTERFACEBOARD + +// +// TFT GLCD Panel with Marlin UI +// Panel connected to main board by SPI or I2C interface. +// See https://github.com/Serhiy-K/TFTGLCDAdapter +// +//#define TFTGLCD_PANEL_SPI +//#define TFTGLCD_PANEL_I2C + +//============================================================================= +//======================= LCD / Controller Selection ======================= +//========================= (Graphical LCDs) ======================== +//============================================================================= + +// +// CONTROLLER TYPE: Graphical 128x64 (DOGM) +// +// IMPORTANT: The U8glib library is required for Graphical Display! +// https://github.com/olikraus/U8glib_Arduino +// +// NOTE: If the LCD is unresponsive you may need to reverse the plugs. +// + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// https://www.panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// MakerLab Mini Panel with graphic +// controller and SD support - https://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// https://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// MKS MINI12864 with graphic controller and SD support +// https://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// MKS LCD12864A/B with graphic controller and SD support. Follows MKS_MINI_12864 pinout. +// https://www.aliexpress.com/item/33018110072.html +// +//#define MKS_LCD12864 + +// +// FYSETC variant of the MINI12864 graphic controller with SD support +// https://wiki.fysetc.com/Mini12864_Panel/ +// +//#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default +//#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) +//#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight +//#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// Ender-2 OEM display, a variant of the MKS_MINI_12864 +// +//#define ENDER2_STOCKDISPLAY + +// +// ANET and Tronxy Graphical Controller +// +// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 +// A clone of the RepRapDiscount full graphics display but with +// different pins/wiring (see pins_ANET_10.h). Enable one of these. +// +//#define ANET_FULL_GRAPHICS_LCD +//#define ANET_FULL_GRAPHICS_LCD_ALT_WIRING + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/item/32837222770.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// https://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128×64 FULL GRAPHICS CONTROLLER +// https://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Zonestar OLED 128×64 FULL GRAPHICS CONTROLLER +// +//#define ZONESTAR_12864LCD // Graphical (DOGM) with ST7920 controller +//#define ZONESTAR_12864OLED // 1.3" OLED with SH1106 controller (default) +//#define ZONESTAR_12864OLED_SSD1306 // 0.96" OLED with SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + +// +// FYSETC OLED 2.42" 128×64 FULL GRAPHICS CONTROLLER with WS2812 RGB +// Where to find : https://www.aliexpress.com/item/4000345255731.html +//#define FYSETC_242_OLED_12864 // Uses the SSD1309 controller + +//============================================================================= +//========================== Extensible UI Displays =========================== +//============================================================================= + +// +// DGUS Touch Display with DWIN OS. (Choose one.) +// ORIGIN : https://www.aliexpress.com/item/32993409517.html +// FYSETC : https://www.aliexpress.com/item/32961471929.html +// +//#define DGUS_LCD_UI_ORIGIN +//#define DGUS_LCD_UI_FYSETC +//#define DGUS_LCD_UI_HIPRECY + +// +// Touch-screen LCD for Malyan M200/M300 printers +// +//#define MALYAN_LCD +#if ENABLED(MALYAN_LCD) + #define LCD_SERIAL_PORT 1 // Default is 1 for Malyan M200 +#endif + +// +// Touch UI for FTDI EVE (FT800/FT810) displays +// See Configuration_adv.h for all configuration options. +// +//#define TOUCH_UI_FTDI_EVE + +// +// Touch-screen LCD for Anycubic printers +// +//#define ANYCUBIC_LCD_I3MEGA +//#define ANYCUBIC_LCD_CHIRON +#if EITHER(ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON) + #define LCD_SERIAL_PORT 3 // Default is 3 for Anycubic + //#define ANYCUBIC_LCD_DEBUG +#endif + +// +// Third-party or vendor-customized controller interfaces. +// Sources should be installed in 'src/lcd/extui'. +// +//#define EXTENSIBLE_UI + +#if ENABLED(EXTENSIBLE_UI) + //#define EXTUI_LOCAL_BEEPER // Enables use of local Beeper pin with external display +#endif + +//============================================================================= +//=============================== Graphical TFTs ============================== +//============================================================================= + +/** + * Specific TFT Model Presets. Enable one of the following options + * or enable TFT_GENERIC and set sub-options. + */ + +// +// 480x320, 3.5", SPI Display From MKS +// Normally used in MKS Robin Nano V2 +// +#define MKS_TS35_V2_0 + +// +// 320x240, 2.4", FSMC Display From MKS +// Normally used in MKS Robin Nano V1.2 +// +//#define MKS_ROBIN_TFT24 + +// +// 320x240, 2.8", FSMC Display From MKS +// Normally used in MKS Robin Nano V1.2 +// +//#define MKS_ROBIN_TFT28 + +// +// 320x240, 3.2", FSMC Display From MKS +// Normally used in MKS Robin Nano V1.2 +// +//#define MKS_ROBIN_TFT32 + +// +// 480x320, 3.5", FSMC Display From MKS +// Normally used in MKS Robin Nano V1.2 +// +//#define MKS_ROBIN_TFT35 + +// +// 480x272, 4.3", FSMC Display From MKS +// +//#define MKS_ROBIN_TFT43 + +// +// 320x240, 3.2", FSMC Display From MKS +// Normally used in MKS Robin +// +//#define MKS_ROBIN_TFT_V1_1R + +// +// 480x320, 3.5", FSMC Stock Display from TronxXY +// +//#define TFT_TRONXY_X5SA + +// +// 480x320, 3.5", FSMC Stock Display from AnyCubic +// +//#define ANYCUBIC_TFT35 + +// +// 320x240, 2.8", FSMC Stock Display from Longer/Alfawise +// +//#define LONGER_LK_TFT28 + +// +// 320x240, 2.8", FSMC Stock Display from ET4 +// +//#define ANET_ET4_TFT28 + +// +// 480x320, 3.5", FSMC Stock Display from ET5 +// +//#define ANET_ET5_TFT35 + +// +// Generic TFT with detailed options +// +//#define TFT_GENERIC +#if ENABLED(TFT_GENERIC) + // :[ 'AUTO', 'ST7735', 'ST7789', 'ST7796', 'R61505', 'ILI9328', 'ILI9341', 'ILI9488' ] + #define TFT_DRIVER AUTO + + // Interface. Enable one of the following options: + //#define TFT_INTERFACE_FSMC + //#define TFT_INTERFACE_SPI + + // TFT Resolution. Enable one of the following options: + //#define TFT_RES_320x240 + //#define TFT_RES_480x272 + //#define TFT_RES_480x320 +#endif + +/** + * TFT UI - User Interface Selection. Enable one of the following options: + * + * TFT_CLASSIC_UI - Emulated DOGM - 128x64 Upscaled + * TFT_COLOR_UI - Marlin Default Menus, Touch Friendly, using full TFT capabilities + * TFT_LVGL_UI - A Modern UI using LVGL + * + * For LVGL_UI also copy the 'assets' folder from the build directory to the + * root of your SD card, together with the compiled firmware. + */ +//#define TFT_CLASSIC_UI +//#define TFT_COLOR_UI +#define TFT_LVGL_UI + +#if ENABLED(TFT_LVGL_UI) + #define MKS_WIFI_MODULE // MKS WiFi module +#endif + +/** + * TFT Rotation. Set to one of the following values: + * + * TFT_ROTATE_90, TFT_ROTATE_90_MIRROR_X, TFT_ROTATE_90_MIRROR_Y, + * TFT_ROTATE_180, TFT_ROTATE_180_MIRROR_X, TFT_ROTATE_180_MIRROR_Y, + * TFT_ROTATE_270, TFT_ROTATE_270_MIRROR_X, TFT_ROTATE_270_MIRROR_Y, + * TFT_MIRROR_X, TFT_MIRROR_Y, TFT_NO_ROTATION + */ +//#define TFT_ROTATION TFT_NO_ROTATION + +//============================================================================= +//============================ Other Controllers ============================ +//============================================================================= + +// +// Ender-3 v2 OEM display. A DWIN display with Rotary Encoder. +// +//#define DWIN_CREALITY_LCD + +// +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 +// +#define TOUCH_SCREEN +#if ENABLED(TOUCH_SCREEN) + #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens + #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus + + #define TOUCH_SCREEN_CALIBRATION + + //#define TOUCH_CALIBRATION_X 12316 + //#define TOUCH_CALIBRATION_Y -8981 + //#define TOUCH_OFFSET_X -43 + //#define TOUCH_OFFSET_Y 257 + //#define TOUCH_ORIENTATION TOUCH_LANDSCAPE + + #if ENABLED(TFT_COLOR_UI) + //#define SINGLE_TOUCH_NAVIGATION + #endif +#endif + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// https://reprapworld.com/products/electronics/ramps/keypad_v1_0_fully_assembled/ +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Set number of user-controlled fans. Disable to use all board-defined fans. +// :[1,2,3,4,5,6,7,8] +//#define NUM_M106_FANS 1 + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +// Support for PCA9533 PWM LED driver +//#define PCA9533 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For NeoPixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOSFET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + */ +//#define RGB_LED +//#define RGBW_LED + +#if EITHER(RGB_LED, RGBW_LED) + //#define RGB_LED_R_PIN 34 + //#define RGB_LED_G_PIN 43 + //#define RGB_LED_B_PIN 35 + //#define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit NeoPixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.) + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + + // Support for second Adafruit NeoPixel LED driver controlled with M150 S1 ... + //#define NEOPIXEL2_SEPARATE + #if ENABLED(NEOPIXEL2_SEPARATE) + #define NEOPIXEL2_PIXELS 15 // Number of LEDs in the second strip + #define NEOPIXEL2_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL2_STARTUP_TEST // Cycle through colors at startup + #else + //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel + #endif + + // Use a single NeoPixel LED for static (background) lighting + //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use + //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Set to 0 to turn off servo support. + */ +#define NUM_SERVOS 1 // Servo index starts with 0 for M280 command + +// (ms) Delay before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Only power servos during movement, otherwise leave off to prevent jitter +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +// Edit servo angles with M281 and save to EEPROM with M500 +//#define EDITABLE_SERVO_ANGLES |