1 files changed, 61 insertions, 0 deletions
diff --git a/Marlin/src/HAL/DUE/inc/SanityCheck.h b/Marlin/src/HAL/DUE/inc/SanityCheck.h
new file mode 100644
index 0000000..26fb44f
--- /dev/null
+++ b/Marlin/src/HAL/DUE/inc/SanityCheck.h
@@ -0,0 +1,61 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+/**
+ * Test Arduino Due specific configuration values for errors at compile-time.
+ */
+
+/**
+ * HARDWARE VS. SOFTWARE SPI COMPATIBILITY
+ *
+ * DUE selects hardware vs. software SPI depending on whether one of the hardware-controllable SDSS pins is in use.
+ *
+ * The hardware SPI controller doesn't allow software SPIs to control any shared pins.
+ *
+ * When DUE software SPI is used then Trinamic drivers must use the TMC softSPI.
+ *
+ * When DUE hardware SPI is used then a Trinamic driver can use either its hardware SPI or, if there are no shared
+ * pins, its software SPI.
+ *
+ * Usually the hardware SPI pins are only available to the LCD. This makes the DUE hard SPI used at the same time
+ * as the TMC2130 soft SPI the most common setup.
+ */
+#define _IS_HW_SPI(P) (defined(TMC_SW_##P) && (TMC_SW_##P == SD_MOSI_PIN || TMC_SW_##P == SD_MISO_PIN || TMC_SW_##P == SD_SCK_PIN))
+
+#if ENABLED(SDSUPPORT) && HAS_DRIVER(TMC2130)
+  #if ENABLED(TMC_USE_SW_SPI)
+    #if DISABLED(DUE_SOFTWARE_SPI) && (_IS_HW_SPI(MOSI) || _IS_HW_SPI(MISO) || _IS_HW_SPI(SCK))
+      #error "DUE hardware SPI is required but is incompatible with TMC2130 software SPI. Either disable TMC_USE_SW_SPI or use separate pins for the two SPIs."
+    #endif
+  #elif ENABLED(DUE_SOFTWARE_SPI)
+    #error "DUE software SPI is required but is incompatible with TMC2130 hardware SPI. Enable TMC_USE_SW_SPI to fix."
+  #endif
+#endif
+
+#if ENABLED(FAST_PWM_FAN) || SPINDLE_LASER_FREQUENCY
+  #error "Features requiring Hardware PWM (FAST_PWM_FAN, SPINDLE_LASER_FREQUENCY) are not yet supported on DUE."
+#endif
+
+#if HAS_TMC_SW_SERIAL
+  #error "TMC220x Software Serial is not supported on this platform."
+#endif