diff options
Diffstat (limited to 'Marlin/src/inc/SanityCheck.h')
| -rw-r--r-- | Marlin/src/inc/SanityCheck.h | 3367 |
1 files changed, 3367 insertions, 0 deletions
diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h new file mode 100644 index 0000000..b3beedf --- /dev/null +++ b/Marlin/src/inc/SanityCheck.h @@ -0,0 +1,3367 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * SanityCheck.h + * + * Test configuration values for errors at compile-time. + */ + +/** + * Require gcc 4.7 or newer (first included with Arduino 1.6.8) for C++11 features. + */ +#if __cplusplus < 201103L + #error "Marlin requires C++11 support (gcc >= 4.7, Arduino IDE >= 1.6.8). Please upgrade your toolchain." +#endif + +// Make sure macros aren't borked +#define TEST1 +#define TEST2 1 +#define TEST3 0 +#define TEST4 true +#if ENABLED(TEST0) || !ENABLED(TEST2) || ENABLED(TEST3) + #error "ENABLED is borked!" +#endif +#if BOTH(TEST0, TEST1) + #error "BOTH is borked!" +#endif +#if DISABLED(TEST1) || !DISABLED(TEST3) || DISABLED(TEST4) || DISABLED(TEST0, TEST1, TEST2, TEST4) || !DISABLED(TEST0, TEST3) + #error "DISABLED is borked!" +#endif +#if !ANY(TEST1, TEST2, TEST3, TEST4) || ANY(TEST0, TEST3) + #error "ANY is borked!" +#endif +#if NONE(TEST0, TEST1, TEST2, TEST4) || !NONE(TEST0, TEST3) + #error "NONE is borked!" +#endif +#undef TEST1 +#undef TEST2 +#undef TEST3 +#undef TEST4 + +/** + * We try our best to include sanity checks for all changed configuration + * directives because users have a tendency to use outdated config files with + * the bleeding-edge source code, but sometimes this is not enough. This check + * forces a minimum config file revision. Otherwise Marlin will not build. + */ +#define HEXIFY(H) _CAT(0x,H) +#if !defined(CONFIGURATION_H_VERSION) || HEXIFY(CONFIGURATION_H_VERSION) < HEXIFY(REQUIRED_CONFIGURATION_H_VERSION) + #error "You are using an old Configuration.h file, update it before building Marlin." +#endif + +#if !defined(CONFIGURATION_ADV_H_VERSION) || HEXIFY(CONFIGURATION_ADV_H_VERSION) < HEXIFY(REQUIRED_CONFIGURATION_ADV_H_VERSION) + #error "You are using an old Configuration_adv.h file, update it before building Marlin." +#endif +#undef HEXIFY + +/** + * Warnings for old configurations + */ +#ifndef MOTHERBOARD + #error "MOTHERBOARD is required." +#elif !defined(X_BED_SIZE) || !defined(Y_BED_SIZE) + #error "X_BED_SIZE and Y_BED_SIZE are now required!" +#elif WATCH_TEMP_PERIOD > 500 + #error "WATCH_TEMP_PERIOD now uses seconds instead of milliseconds." +#elif DISABLED(THERMAL_PROTECTION_HOTENDS) && (defined(WATCH_TEMP_PERIOD) || defined(THERMAL_PROTECTION_PERIOD)) + #error "Thermal Runaway Protection for hotends is now enabled with THERMAL_PROTECTION_HOTENDS." +#elif DISABLED(THERMAL_PROTECTION_BED) && defined(THERMAL_PROTECTION_BED_PERIOD) + #error "Thermal Runaway Protection for the bed is now enabled with THERMAL_PROTECTION_BED." +#elif (CORE_IS_XZ || CORE_IS_YZ) && ENABLED(Z_LATE_ENABLE) + #error "Z_LATE_ENABLE can't be used with COREXZ, COREZX, COREYZ, or COREZY." +#elif defined(X_HOME_RETRACT_MM) + #error "[XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM." +#elif defined(SDCARDDETECTINVERTED) + #error "SDCARDDETECTINVERTED is now SD_DETECT_STATE (HIGH)." +#elif defined(SD_DETECT_INVERTED) + #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH)." +#elif defined(BTENABLED) + #error "BTENABLED is now BLUETOOTH." +#elif defined(CUSTOM_MENDEL_NAME) + #error "CUSTOM_MENDEL_NAME is now CUSTOM_MACHINE_NAME." +#elif defined(HAS_AUTOMATIC_VERSIONING) + #error "HAS_AUTOMATIC_VERSIONING is now CUSTOM_VERSION_FILE." +#elif defined(USE_AUTOMATIC_VERSIONING) + #error "USE_AUTOMATIC_VERSIONING is now CUSTOM_VERSION_FILE." +#elif defined(SDSLOW) + #error "SDSLOW deprecated. Set SD_SPI_SPEED to SPI_HALF_SPEED instead." +#elif defined(SDEXTRASLOW) + #error "SDEXTRASLOW deprecated. Set SD_SPI_SPEED to SPI_QUARTER_SPEED instead." +#elif defined(FILAMENT_SENSOR) + #error "FILAMENT_SENSOR is now FILAMENT_WIDTH_SENSOR." +#elif defined(ENDSTOPPULLUP_FIL_RUNOUT) + #error "ENDSTOPPULLUP_FIL_RUNOUT is now FIL_RUNOUT_PULLUP." +#elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS) + #error "DISABLE_MAX_ENDSTOPS and DISABLE_MIN_ENDSTOPS deprecated. Use individual USE_*_PLUG options instead." +#elif defined(LANGUAGE_INCLUDE) + #error "LANGUAGE_INCLUDE has been replaced by LCD_LANGUAGE." +#elif defined(EXTRUDER_OFFSET_X) || defined(EXTRUDER_OFFSET_Y) + #error "EXTRUDER_OFFSET_[XY] is deprecated. Use HOTEND_OFFSET_[XY] instead." +#elif defined(PID_PARAMS_PER_EXTRUDER) + #error "PID_PARAMS_PER_EXTRUDER is deprecated. Use PID_PARAMS_PER_HOTEND instead." +#elif defined(EXTRUDER_WATTS) || defined(BED_WATTS) + #error "EXTRUDER_WATTS and BED_WATTS are deprecated and should be removed." +#elif defined(SERVO_ENDSTOP_ANGLES) + #error "SERVO_ENDSTOP_ANGLES is deprecated. Use Z_SERVO_ANGLES instead." +#elif defined(X_ENDSTOP_SERVO_NR) || defined(Y_ENDSTOP_SERVO_NR) + #error "X_ENDSTOP_SERVO_NR and Y_ENDSTOP_SERVO_NR are deprecated and should be removed." +#elif defined(Z_ENDSTOP_SERVO_NR) + #error "Z_ENDSTOP_SERVO_NR is now Z_PROBE_SERVO_NR." +#elif defined(DEFAULT_XYJERK) + #error "DEFAULT_XYJERK is deprecated. Use DEFAULT_XJERK and DEFAULT_YJERK instead." +#elif defined(XY_TRAVEL_SPEED) + #error "XY_TRAVEL_SPEED is deprecated. Use XY_PROBE_SPEED instead." +#elif defined(PROBE_SERVO_DEACTIVATION_DELAY) + #error "PROBE_SERVO_DEACTIVATION_DELAY is deprecated. Use DEACTIVATE_SERVOS_AFTER_MOVE instead." +#elif defined(SERVO_DEACTIVATION_DELAY) + #error "SERVO_DEACTIVATION_DELAY is now SERVO_DELAY." +#elif ENABLED(FILAMENTCHANGEENABLE) + #error "FILAMENTCHANGEENABLE is now ADVANCED_PAUSE_FEATURE." +#elif ENABLED(FILAMENT_CHANGE_FEATURE) + #error "FILAMENT_CHANGE_FEATURE is now ADVANCED_PAUSE_FEATURE." +#elif defined(FILAMENT_CHANGE_X_POS) || defined(FILAMENT_CHANGE_Y_POS) + #error "FILAMENT_CHANGE_[XY]_POS is now set with NOZZLE_PARK_POINT." +#elif defined(FILAMENT_CHANGE_Z_ADD) + #error "FILAMENT_CHANGE_Z_ADD is now set with NOZZLE_PARK_POINT." +#elif defined(FILAMENT_CHANGE_XY_FEEDRATE) + #error "FILAMENT_CHANGE_XY_FEEDRATE is now NOZZLE_PARK_XY_FEEDRATE." +#elif defined(FILAMENT_CHANGE_Z_FEEDRATE) + #error "FILAMENT_CHANGE_Z_FEEDRATE is now NOZZLE_PARK_Z_FEEDRATE." +#elif defined(PAUSE_PARK_X_POS) || defined(PAUSE_PARK_Y_POS) + #error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT." +#elif defined(PAUSE_PARK_Z_ADD) + #error "PAUSE_PARK_Z_ADD is now set with NOZZLE_PARK_POINT." +#elif defined(PAUSE_PARK_XY_FEEDRATE) + #error "PAUSE_PARK_XY_FEEDRATE is now NOZZLE_PARK_XY_FEEDRATE." +#elif defined(PAUSE_PARK_Z_FEEDRATE) + #error "PAUSE_PARK_Z_FEEDRATE is now NOZZLE_PARK_Z_FEEDRATE." +#elif defined(FILAMENT_CHANGE_RETRACT_FEEDRATE) + #error "FILAMENT_CHANGE_RETRACT_FEEDRATE is now PAUSE_PARK_RETRACT_FEEDRATE." +#elif defined(FILAMENT_CHANGE_RETRACT_LENGTH) + #error "FILAMENT_CHANGE_RETRACT_LENGTH is now PAUSE_PARK_RETRACT_LENGTH." +#elif defined(FILAMENT_CHANGE_EXTRUDE_FEEDRATE) + #error "FILAMENT_CHANGE_EXTRUDE_FEEDRATE is now ADVANCED_PAUSE_PURGE_FEEDRATE." +#elif defined(ADVANCED_PAUSE_EXTRUDE_FEEDRATE) + #error "ADVANCED_PAUSE_EXTRUDE_FEEDRATE is now ADVANCED_PAUSE_PURGE_FEEDRATE." +#elif defined(FILAMENT_CHANGE_EXTRUDE_LENGTH) + #error "FILAMENT_CHANGE_EXTRUDE_LENGTH is now ADVANCED_PAUSE_PURGE_LENGTH." +#elif defined(ADVANCED_PAUSE_EXTRUDE_LENGTH) + #error "ADVANCED_PAUSE_EXTRUDE_LENGTH is now ADVANCED_PAUSE_PURGE_LENGTH." +#elif defined(FILAMENT_CHANGE_NOZZLE_TIMEOUT) + #error "FILAMENT_CHANGE_NOZZLE_TIMEOUT is now PAUSE_PARK_NOZZLE_TIMEOUT." +#elif defined(FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS) + #error "FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS is now FILAMENT_CHANGE_ALERT_BEEPS." +#elif defined(FILAMENT_CHANGE_NO_STEPPER_TIMEOUT) + #error "FILAMENT_CHANGE_NO_STEPPER_TIMEOUT is now PAUSE_PARK_NO_STEPPER_TIMEOUT." +#elif defined(PLA_PREHEAT_HOTEND_TEMP) + #error "PLA_PREHEAT_HOTEND_TEMP is now PREHEAT_1_TEMP_HOTEND." +#elif defined(PLA_PREHEAT_HPB_TEMP) + #error "PLA_PREHEAT_HPB_TEMP is now PREHEAT_1_TEMP_BED." +#elif defined(PLA_PREHEAT_FAN_SPEED) + #error "PLA_PREHEAT_FAN_SPEED is now PREHEAT_1_FAN_SPEED." +#elif defined(ABS_PREHEAT_HOTEND_TEMP) + #error "ABS_PREHEAT_HOTEND_TEMP is now PREHEAT_2_TEMP_HOTEND." +#elif defined(ABS_PREHEAT_HPB_TEMP) + #error "ABS_PREHEAT_HPB_TEMP is now PREHEAT_2_TEMP_BED." +#elif defined(ABS_PREHEAT_FAN_SPEED) + #error "ABS_PREHEAT_FAN_SPEED is now PREHEAT_2_FAN_SPEED." +#elif defined(ENDSTOPS_ONLY_FOR_HOMING) + #error "ENDSTOPS_ONLY_FOR_HOMING is deprecated. Use (disable) ENDSTOPS_ALWAYS_ON_DEFAULT instead." +#elif defined(HOMING_FEEDRATE) + #error "HOMING_FEEDRATE is now set using the HOMING_FEEDRATE_MM_M array instead." +#elif (defined(HOMING_FEEDRATE_XY) || defined(HOMING_FEEDRATE_Z)) && !defined(HOMING_FEEDRATE_MM_M) + #error "HOMING_FEEDRATE_XY and HOMING_FEEDRATE_Z are now set using the HOMING_FEEDRATE_MM_M array instead." +#elif defined(MANUAL_HOME_POSITIONS) + #error "MANUAL_HOME_POSITIONS is deprecated. Set MANUAL_[XYZ]_HOME_POS as-needed instead." +#elif defined(PID_ADD_EXTRUSION_RATE) + #error "PID_ADD_EXTRUSION_RATE is now PID_EXTRUSION_SCALING and is DISABLED by default." +#elif defined(Z_RAISE_BEFORE_HOMING) + #error "Z_RAISE_BEFORE_HOMING is now Z_HOMING_HEIGHT." +#elif defined(MIN_Z_HEIGHT_FOR_HOMING) + #error "MIN_Z_HEIGHT_FOR_HOMING is now Z_HOMING_HEIGHT." +#elif defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING) + #error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_CLEARANCE_DEPLOY_PROBE and Z_AFTER_PROBING instead." +#elif defined(Z_RAISE_PROBE_DEPLOY_STOW) || defined(Z_RAISE_BETWEEN_PROBINGS) + #error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES." +#elif defined(Z_PROBE_DEPLOY_HEIGHT) || defined(Z_PROBE_TRAVEL_HEIGHT) + #error "Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES." +#elif defined(MANUAL_BED_LEVELING) + #error "MANUAL_BED_LEVELING is now LCD_BED_LEVELING." +#elif defined(MESH_HOME_SEARCH_Z) + #error "MESH_HOME_SEARCH_Z is now LCD_PROBE_Z_RANGE." +#elif defined(MANUAL_PROBE_Z_RANGE) + #error "MANUAL_PROBE_Z_RANGE is now LCD_PROBE_Z_RANGE." +#elif !defined(MIN_STEPS_PER_SEGMENT) + #error "Please replace 'const int dropsegments' with '#define MIN_STEPS_PER_SEGMENT' (and increase by 1)." +#elif MIN_STEPS_PER_SEGMENT <= 0 + #error "MIN_STEPS_PER_SEGMENT must be at least 1." +#elif defined(PREVENT_DANGEROUS_EXTRUDE) + #error "PREVENT_DANGEROUS_EXTRUDE is now PREVENT_COLD_EXTRUSION." +#elif defined(SCARA) + #error "SCARA is now MORGAN_SCARA." +#elif defined(ENABLE_AUTO_BED_LEVELING) + #error "ENABLE_AUTO_BED_LEVELING is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT." +#elif defined(AUTO_BED_LEVELING_FEATURE) + #error "AUTO_BED_LEVELING_FEATURE is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT." +#elif defined(ABL_GRID_POINTS) + #error "ABL_GRID_POINTS is now GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y." +#elif defined(ABL_GRID_POINTS_X) || defined(ABL_GRID_POINTS_Y) + #error "ABL_GRID_POINTS_[XY] is now GRID_MAX_POINTS_[XY]." +#elif defined(ABL_GRID_MAX_POINTS_X) || defined(ABL_GRID_MAX_POINTS_Y) + #error "ABL_GRID_MAX_POINTS_[XY] is now GRID_MAX_POINTS_[XY]." +#elif defined(MESH_NUM_X_POINTS) || defined(MESH_NUM_Y_POINTS) + #error "MESH_NUM_[XY]_POINTS is now GRID_MAX_POINTS_[XY]." +#elif defined(UBL_MESH_NUM_X_POINTS) || defined(UBL_MESH_NUM_Y_POINTS) + #error "UBL_MESH_NUM_[XY]_POINTS is now GRID_MAX_POINTS_[XY]." +#elif defined(UBL_G26_MESH_VALIDATION) + #error "UBL_G26_MESH_VALIDATION is now G26_MESH_VALIDATION." +#elif defined(UBL_MESH_EDIT_ENABLED) + #error "UBL_MESH_EDIT_ENABLED is now G26_MESH_VALIDATION." +#elif defined(UBL_MESH_EDITING) + #error "UBL_MESH_EDITING is now G26_MESH_VALIDATION." +#elif defined(BLTOUCH_HEATERS_OFF) + #error "BLTOUCH_HEATERS_OFF is now PROBING_HEATERS_OFF." +#elif defined(BLTOUCH_V3) + #error "BLTOUCH_V3 is obsolete." +#elif defined(BLTOUCH_FORCE_OPEN_DRAIN_MODE) + #error "BLTOUCH_FORCE_OPEN_DRAIN_MODE is obsolete." +#elif defined(BEEPER) + #error "BEEPER is now BEEPER_PIN." +#elif defined(SDCARDDETECT) + #error "SDCARDDETECT is now SD_DETECT_PIN." +#elif defined(STAT_LED_RED) || defined(STAT_LED_BLUE) + #error "STAT_LED_RED/STAT_LED_BLUE are now STAT_LED_RED_PIN/STAT_LED_BLUE_PIN." +#elif defined(LCD_PIN_BL) + #error "LCD_PIN_BL is now LCD_BACKLIGHT_PIN." +#elif defined(LCD_PIN_RESET) + #error "LCD_PIN_RESET is now LCD_RESET_PIN." +#elif defined(EXTRUDER_0_AUTO_FAN_PIN) || defined(EXTRUDER_1_AUTO_FAN_PIN) || defined(EXTRUDER_2_AUTO_FAN_PIN) || defined(EXTRUDER_3_AUTO_FAN_PIN) + #error "EXTRUDER_[0123]_AUTO_FAN_PIN is now E[0123]_AUTO_FAN_PIN." +#elif defined(PID_FAN_SCALING) && !HAS_FAN + #error "PID_FAN_SCALING needs at least one fan enabled." +#elif defined(min_software_endstops) || defined(max_software_endstops) + #error "(min|max)_software_endstops are now (MIN|MAX)_SOFTWARE_ENDSTOPS." +#elif ENABLED(Z_PROBE_SLED) && defined(SLED_PIN) + #error "Replace SLED_PIN with SOL1_PIN (applies to both Z_PROBE_SLED and SOLENOID_PROBE)." +#elif defined(CONTROLLERFAN_PIN) + #error "CONTROLLERFAN_PIN is now CONTROLLER_FAN_PIN, enabled with USE_CONTROLLER_FAN." +#elif defined(CONTROLLERFAN_SPEED) + #error "CONTROLLERFAN_SPEED is now CONTROLLERFAN_SPEED_ACTIVE." +#elif defined(CONTROLLERFAN_SECS) + #error "CONTROLLERFAN_SECS is now CONTROLLERFAN_IDLE_TIME." +#elif defined(MIN_RETRACT) + #error "MIN_RETRACT is now MIN_AUTORETRACT and MAX_AUTORETRACT." +#elif defined(ADVANCE) + #error "ADVANCE is now LIN_ADVANCE." +#elif defined(LIN_ADVANCE_E_D_RATIO) + #error "LIN_ADVANCE (1.5) no longer uses LIN_ADVANCE_E_D_RATIO." +#elif defined(NEOPIXEL_RGBW_LED) + #error "NEOPIXEL_RGBW_LED is now NEOPIXEL_LED." +#elif ENABLED(DELTA) && defined(DELTA_PROBEABLE_RADIUS) + #error "Remove DELTA_PROBEABLE_RADIUS and use PROBING_MARGIN to inset the probe area instead." +#elif ENABLED(DELTA) && defined(DELTA_CALIBRATION_RADIUS) + #error "Remove DELTA_CALIBRATION_RADIUS and use PROBING_MARGIN to inset the probe area instead." +#elif defined(UBL_MESH_INSET) + #error "UBL_MESH_INSET is now just MESH_INSET." +#elif defined(UBL_MESH_MIN_X) || defined(UBL_MESH_MIN_Y) || defined(UBL_MESH_MAX_X) || defined(UBL_MESH_MAX_Y) + #error "UBL_MESH_(MIN|MAX)_[XY] is now just MESH_(MIN|MAX)_[XY]." +#elif defined(ABL_PROBE_PT_1_X) || defined(ABL_PROBE_PT_1_Y) || defined(ABL_PROBE_PT_2_X) || defined(ABL_PROBE_PT_2_Y) || defined(ABL_PROBE_PT_3_X) || defined(ABL_PROBE_PT_3_Y) + #error "ABL_PROBE_PT_[123]_[XY] is no longer required. Please remove it." +#elif defined(UBL_PROBE_PT_1_X) || defined(UBL_PROBE_PT_1_Y) || defined(UBL_PROBE_PT_2_X) || defined(UBL_PROBE_PT_2_Y) || defined(UBL_PROBE_PT_3_X) || defined(UBL_PROBE_PT_3_Y) + #error "UBL_PROBE_PT_[123]_[XY] is no longer required. Please remove it." +#elif defined(MIN_PROBE_EDGE) + #error "MIN_PROBE_EDGE is now called PROBING_MARGIN." +#elif defined(MIN_PROBE_EDGE_LEFT) + #error "MIN_PROBE_EDGE_LEFT is now called PROBING_MARGIN_LEFT." +#elif defined(MIN_PROBE_EDGE_RIGHT) + #error "MIN_PROBE_EDGE_RIGHT is now called PROBING_MARGIN_RIGHT." +#elif defined(MIN_PROBE_EDGE_FRONT) + #error "MIN_PROBE_EDGE_FRONT is now called PROBING_MARGIN_FRONT." +#elif defined(MIN_PROBE_EDGE_BACK) + #error "MIN_PROBE_EDGE_BACK is now called PROBING_MARGIN_BACK." +#elif defined(LEFT_PROBE_BED_POSITION) + #error "LEFT_PROBE_BED_POSITION is obsolete. Set a margin with PROBING_MARGIN or PROBING_MARGIN_LEFT instead." +#elif defined(RIGHT_PROBE_BED_POSITION) + #error "RIGHT_PROBE_BED_POSITION is obsolete. Set a margin with PROBING_MARGIN or PROBING_MARGIN_RIGHT instead." +#elif defined(FRONT_PROBE_BED_POSITION) + #error "FRONT_PROBE_BED_POSITION is obsolete. Set a margin with PROBING_MARGIN or PROBING_MARGIN_FRONT instead." +#elif defined(BACK_PROBE_BED_POSITION) + #error "BACK_PROBE_BED_POSITION is obsolete. Set a margin with PROBING_MARGIN or PROBING_MARGIN_BACK instead." +#elif defined(ENABLE_MESH_EDIT_GFX_OVERLAY) + #error "ENABLE_MESH_EDIT_GFX_OVERLAY is now MESH_EDIT_GFX_OVERLAY." +#elif defined(BABYSTEP_ZPROBE_GFX_REVERSE) + #error "BABYSTEP_ZPROBE_GFX_REVERSE is now set by OVERLAY_GFX_REVERSE." +#elif defined(UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN) + #error "UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN is now SEGMENT_LEVELED_MOVES." +#elif HAS_PID_HEATING && (defined(K1) || !defined(PID_K1)) + #error "K1 is now PID_K1." +#elif defined(PROBE_DOUBLE_TOUCH) + #error "PROBE_DOUBLE_TOUCH is now MULTIPLE_PROBING." +#elif defined(ANET_KEYPAD_LCD) + #error "ANET_KEYPAD_LCD is now ZONESTAR_LCD." +#elif defined(LCD_I2C_SAINSMART_YWROBOT) + #error "LCD_I2C_SAINSMART_YWROBOT is now LCD_SAINSMART_I2C_(1602|2004)." +#elif defined(MEASURED_LOWER_LIMIT) || defined(MEASURED_UPPER_LIMIT) + #error "MEASURED_(UPPER|LOWER)_LIMIT is now FILWIDTH_ERROR_MARGIN." +#elif defined(HAVE_TMCDRIVER) + #error "HAVE_TMCDRIVER is now [AXIS]_DRIVER_TYPE TMC26X." +#elif defined(STEALTHCHOP) + #error "STEALTHCHOP is now STEALTHCHOP_(XY|Z|E)." +#elif defined(HAVE_TMC26X) + #error "HAVE_TMC26X is now [AXIS]_DRIVER_TYPE TMC26X." +#elif defined(HAVE_TMC2130) + #error "HAVE_TMC2130 is now [AXIS]_DRIVER_TYPE TMC2130." +#elif defined(HAVE_TMC2208) + #error "HAVE_TMC2208 is now [AXIS]_DRIVER_TYPE TMC2208." +#elif defined(HAVE_L6470DRIVER) + #error "HAVE_L6470DRIVER is now [AXIS]_DRIVER_TYPE L6470." +#elif defined(X_IS_TMC) || defined(X2_IS_TMC) || defined(Y_IS_TMC) || defined(Y2_IS_TMC) || defined(Z_IS_TMC) || defined(Z2_IS_TMC) || defined(Z3_IS_TMC) \ + || defined(E0_IS_TMC) || defined(E1_IS_TMC) || defined(E2_IS_TMC) || defined(E3_IS_TMC) || defined(E4_IS_TMC) || defined(E5_IS_TMC) || defined(E6_IS_TMC) || defined(E7_IS_TMC) + #error "[AXIS]_IS_TMC is now [AXIS]_DRIVER_TYPE TMC26X." +#elif defined(X_IS_TMC26X) || defined(X2_IS_TMC26X) || defined(Y_IS_TMC26X) || defined(Y2_IS_TMC26X) || defined(Z_IS_TMC26X) || defined(Z2_IS_TMC26X) || defined(Z3_IS_TMC26X) \ + || defined(E0_IS_TMC26X) || defined(E1_IS_TMC26X) || defined(E2_IS_TMC26X) || defined(E3_IS_TMC26X) || defined(E4_IS_TMC26X) || defined(E5_IS_TMC26X) || defined(E6_IS_TMC26X) || defined(E7_IS_TMC26X) + #error "[AXIS]_IS_TMC26X is now [AXIS]_DRIVER_TYPE TMC26X." +#elif defined(X_IS_TMC2130) || defined(X2_IS_TMC2130) || defined(Y_IS_TMC2130) || defined(Y2_IS_TMC2130) || defined(Z_IS_TMC2130) || defined(Z2_IS_TMC2130) || defined(Z3_IS_TMC2130) \ + || defined(E0_IS_TMC2130) || defined(E1_IS_TMC2130) || defined(E2_IS_TMC2130) || defined(E3_IS_TMC2130) || defined(E4_IS_TMC2130) || defined(E5_IS_TMC2130) || defined(E6_IS_TMC2130) || defined(E7_IS_TMC2130) + #error "[AXIS]_IS_TMC2130 is now [AXIS]_DRIVER_TYPE TMC2130." +#elif defined(X_IS_TMC2208) || defined(X2_IS_TMC2208) || defined(Y_IS_TMC2208) || defined(Y2_IS_TMC2208) || defined(Z_IS_TMC2208) || defined(Z2_IS_TMC2208) || defined(Z3_IS_TMC2208) \ + || defined(E0_IS_TMC2208) || defined(E1_IS_TMC2208) || defined(E2_IS_TMC2208) || defined(E3_IS_TMC2208) || defined(E4_IS_TMC2208) || defined(E5_IS_TMC2208) || defined(E6_IS_TMC2208) || defined(E7_IS_TMC2208) + #error "[AXIS]_IS_TMC2208 is now [AXIS]_DRIVER_TYPE TMC2208." +#elif defined(X_IS_L6470) || defined(X2_IS_L6470) || defined(Y_IS_L6470) || defined(Y2_IS_L6470) || defined(Z_IS_L6470) || defined(Z2_IS_L6470) || defined(Z3_IS_L6470) \ + || defined(E0_IS_L6470) || defined(E1_IS_L6470) || defined(E2_IS_L6470) || defined(E3_IS_L6470) || defined(E4_IS_L6470) || defined(E5_IS_L6470) || defined(E6_IS_L6470) || defined(E7_IS_L6470) + #error "[AXIS]_IS_L6470 is now [AXIS]_DRIVER_TYPE L6470." +#elif defined(AUTOMATIC_CURRENT_CONTROL) + #error "AUTOMATIC_CURRENT_CONTROL is now MONITOR_DRIVER_STATUS." +#elif defined(FILAMENT_CHANGE_LOAD_LENGTH) + #error "FILAMENT_CHANGE_LOAD_LENGTH is now FILAMENT_CHANGE_FAST_LOAD_LENGTH." +#elif defined(LEVEL_CORNERS_INSET) + #error "LEVEL_CORNERS_INSET is now LEVEL_CORNERS_INSET_LFRB." +#elif defined(BEZIER_JERK_CONTROL) + #error "BEZIER_JERK_CONTROL is now S_CURVE_ACCELERATION." +#elif HAS_JUNCTION_DEVIATION && defined(JUNCTION_DEVIATION_FACTOR) + #error "JUNCTION_DEVIATION_FACTOR is now JUNCTION_DEVIATION_MM." +#elif defined(JUNCTION_ACCELERATION_FACTOR) + #error "JUNCTION_ACCELERATION_FACTOR is obsolete. Delete it from Configuration_adv.h." +#elif defined(JUNCTION_ACCELERATION) + #error "JUNCTION_ACCELERATION is obsolete. Delete it from Configuration_adv.h." +#elif defined(MAX7219_DEBUG_STEPPER_HEAD) + #error "MAX7219_DEBUG_STEPPER_HEAD is now MAX7219_DEBUG_PLANNER_HEAD." +#elif defined(MAX7219_DEBUG_STEPPER_TAIL) + #error "MAX7219_DEBUG_STEPPER_TAIL is now MAX7219_DEBUG_PLANNER_TAIL." +#elif defined(MAX7219_DEBUG_STEPPER_QUEUE) + #error "MAX7219_DEBUG_STEPPER_QUEUE is now MAX7219_DEBUG_PLANNER_QUEUE." +#elif defined(ENDSTOP_NOISE_FILTER) + #error "ENDSTOP_NOISE_FILTER is now ENDSTOP_NOISE_THRESHOLD [2-7]." +#elif defined(RETRACT_ZLIFT) + #error "RETRACT_ZLIFT is now RETRACT_ZRAISE." +#elif defined(TOOLCHANGE_PARK_ZLIFT) || defined(TOOLCHANGE_UNPARK_ZLIFT) + #error "TOOLCHANGE_PARK_ZLIFT and TOOLCHANGE_UNPARK_ZLIFT are now TOOLCHANGE_ZRAISE." +#elif defined(SINGLENOZZLE_TOOLCHANGE_ZRAISE) + #error "SINGLENOZZLE_TOOLCHANGE_ZRAISE is now TOOLCHANGE_ZRAISE." +#elif defined(SINGLENOZZLE_SWAP_LENGTH) + #error "SINGLENOZZLE_SWAP_LENGTH is now TOOLCHANGE_FIL_SWAP_LENGTH." +#elif defined(SINGLENOZZLE_SWAP_RETRACT_SPEED) + #error "SINGLENOZZLE_SWAP_RETRACT_SPEED is now TOOLCHANGE_FIL_SWAP_RETRACT_SPEED." +#elif defined(SINGLENOZZLE_SWAP_PRIME_SPEED) + #error "SINGLENOZZLE_SWAP_PRIME_SPEED is now TOOLCHANGE_FIL_SWAP_PRIME_SPEED." +#elif defined(SINGLENOZZLE_SWAP_PARK) + #error "SINGLENOZZLE_SWAP_PARK is now TOOLCHANGE_PARK." +#elif defined(SINGLENOZZLE_TOOLCHANGE_XY) + #error "SINGLENOZZLE_TOOLCHANGE_XY is now TOOLCHANGE_PARK_XY." +#elif defined(SINGLENOZZLE_PARK_XY_FEEDRATE) + #error "SINGLENOZZLE_PARK_XY_FEEDRATE is now TOOLCHANGE_PARK_XY_FEEDRATE." +#elif defined(PARKING_EXTRUDER_SECURITY_RAISE) + #error "PARKING_EXTRUDER_SECURITY_RAISE is now TOOLCHANGE_ZRAISE." +#elif defined(SWITCHING_TOOLHEAD_SECURITY_RAISE) + #error "SWITCHING_TOOLHEAD_SECURITY_RAISE is now TOOLCHANGE_ZRAISE." +#elif defined(G0_FEEDRATE) && G0_FEEDRATE == 0 + #error "G0_FEEDRATE is now used to set the G0 feedrate." +#elif defined(MBL_Z_STEP) + #error "MBL_Z_STEP is now MESH_EDIT_Z_STEP." +#elif defined(CHDK) + #error "CHDK is now CHDK_PIN." +#elif defined(MAX6675_SS) || defined(MAX6675_SS2) + #error "MAX6675_SS / MAX6675_SS2 is now MAX6675_SS_PIN / MAX6675_SS2_PIN." +#elif defined(MAX31865_SENSOR_OHMS) + #error "MAX31865_SENSOR_OHMS is now MAX31865_SENSOR_OHMS_0." +#elif defined(MAX31865_CALIBRATION_OHMS) + #error "MAX31865_CALIBRATION_OHMS is now MAX31865_CALIBRATION_OHMS_0." +#elif defined(SPINDLE_LASER_ENABLE) + #error "SPINDLE_LASER_ENABLE is now SPINDLE_FEATURE or LASER_FEATURE." +#elif defined(SPINDLE_LASER_ENABLE_PIN) + #error "SPINDLE_LASER_ENABLE_PIN is now SPINDLE_LASER_ENA_PIN." +#elif defined(SPINDLE_DIR_CHANGE) + #error "SPINDLE_DIR_CHANGE is now SPINDLE_CHANGE_DIR." +#elif defined(SPINDLE_STOP_ON_DIR_CHANGE) + #error "SPINDLE_STOP_ON_DIR_CHANGE is now SPINDLE_CHANGE_DIR_STOP." +#elif defined(SPINDLE_LASER_ACTIVE_HIGH) + #error "SPINDLE_LASER_ACTIVE_HIGH is now SPINDLE_LASER_ACTIVE_STATE." +#elif defined(SPINDLE_LASER_ENABLE_INVERT) + #error "SPINDLE_LASER_ENABLE_INVERT is now SPINDLE_LASER_ACTIVE_STATE." +#elif defined(CUTTER_POWER_DISPLAY) + #error "CUTTER_POWER_DISPLAY is now CUTTER_POWER_UNIT." +#elif defined(CHAMBER_HEATER_PIN) + #error "CHAMBER_HEATER_PIN is now HEATER_CHAMBER_PIN." +#elif defined(TMC_Z_CALIBRATION) + #error "TMC_Z_CALIBRATION has been deprecated in favor of MECHANICAL_GANTRY_CALIBRATION." +#elif defined(Z_MIN_PROBE_ENDSTOP) + #error "Z_MIN_PROBE_ENDSTOP is no longer required. Please remove it." +#elif defined(DUAL_NOZZLE_DUPLICATION_MODE) + #error "DUAL_NOZZLE_DUPLICATION_MODE is now MULTI_NOZZLE_DUPLICATION." +#elif defined(MENU_ITEM_CASE_LIGHT) + #error "MENU_ITEM_CASE_LIGHT is now CASE_LIGHT_MENU." +#elif defined(ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED) + #error "ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED is now SD_ABORT_ON_ENDSTOP_HIT." +#elif defined(LPC_SD_LCD) || defined(LPC_SD_ONBOARD) || defined(LPC_SD_CUSTOM_CABLE) + #error "LPC_SD_(LCD|ONBOARD|CUSTOM_CABLE) are now SDCARD_CONNECTION." +#elif defined(USB_SD_DISABLED) + #error "USB_SD_DISABLED is now NO_SD_HOST_DRIVE." +#elif defined(USB_SD_ONBOARD) + #error "USB_SD_ONBOARD is obsolete. Disable NO_SD_HOST_DRIVE instead." +#elif defined(PSU_ACTIVE_HIGH) + #error "PSU_ACTIVE_HIGH is now PSU_ACTIVE_STATE." +#elif POWER_SUPPLY == 1 + #error "Replace POWER_SUPPLY 1 by enabling PSU_CONTROL and setting PSU_ACTIVE_STATE to 'LOW'." +#elif POWER_SUPPLY == 2 + #error "Replace POWER_SUPPLY 2 by enabling PSU_CONTROL and setting PSU_ACTIVE_STATE to 'HIGH'." +#elif defined(POWER_SUPPLY) + #error "POWER_SUPPLY is now obsolete. Please remove it." +#elif defined(MKS_ROBIN_TFT) + #error "MKS_ROBIN_TFT is now FSMC_GRAPHICAL_TFT." +#elif defined(SDPOWER) + #error "SDPOWER is now SDPOWER_PIN." +#elif defined(STRING_SPLASH_LINE1) || defined(STRING_SPLASH_LINE2) + #error "STRING_SPLASH_LINE[12] are now obsolete. Please remove them." +#elif defined(Z_PROBE_ALLEN_KEY_DEPLOY_1_X) || defined(Z_PROBE_ALLEN_KEY_STOW_1_X) + #error "Z_PROBE_ALLEN_KEY_(DEPLOY|STOW) coordinates are now a single setting." +#elif defined(X_PROBE_OFFSET_FROM_EXTRUDER) || defined(Y_PROBE_OFFSET_FROM_EXTRUDER) || defined(Z_PROBE_OFFSET_FROM_EXTRUDER) + #error "[XYZ]_PROBE_OFFSET_FROM_EXTRUDER is now NOZZLE_TO_PROBE_OFFSET." +#elif defined(MIN_PROBE_X) || defined(MIN_PROBE_Y) || defined(MAX_PROBE_X) || defined(MAX_PROBE_Y) + #error "(MIN|MAX)_PROBE_[XY] are now calculated at runtime. Please remove them." +#elif defined(Z_STEPPER_ALIGN_X) || defined(Z_STEPPER_ALIGN_X) + #error "Z_STEPPER_ALIGN_X and Z_STEPPER_ALIGN_Y are now combined as Z_STEPPER_ALIGN_XY." +#elif defined(JUNCTION_DEVIATION) + #error "JUNCTION_DEVIATION is no longer required. (See CLASSIC_JERK). Please remove it." +#elif defined(BABYSTEP_MULTIPLICATOR) + #error "BABYSTEP_MULTIPLICATOR is now BABYSTEP_MULTIPLICATOR_[XY|Z]." +#elif defined(LULZBOT_TOUCH_UI) + #error "LULZBOT_TOUCH_UI is now TOUCH_UI_FTDI_EVE." +#elif defined(PS_DEFAULT_OFF) + #error "PS_DEFAULT_OFF is now PSU_DEFAULT_OFF." +#elif defined(FILAMENT_UNLOAD_RETRACT_LENGTH) + #error "FILAMENT_UNLOAD_RETRACT_LENGTH is now FILAMENT_UNLOAD_PURGE_RETRACT." +#elif defined(FILAMENT_UNLOAD_DELAY) + #error "FILAMENT_UNLOAD_DELAY is now FILAMENT_UNLOAD_PURGE_DELAY." +#elif defined(HOME_USING_SPREADCYCLE) + #error "HOME_USING_SPREADCYCLE is now obsolete. Please remove it." +#elif defined(DGUS_LCD) + #error "DGUS_LCD is now DGUS_LCD_UI_(ORIGIN|FYSETC|HIPRECY)." +#elif defined(DGUS_SERIAL_PORT) + #error "DGUS_SERIAL_PORT is now LCD_SERIAL_PORT." +#elif defined(DGUS_BAUDRATE) + #error "DGUS_BAUDRATE is now LCD_BAUDRATE." +#elif defined(DGUS_STATS_RX_BUFFER_OVERRUNS) + #error "DGUS_STATS_RX_BUFFER_OVERRUNS is now STATS_RX_BUFFER_OVERRUNS." +#elif defined(ANYCUBIC_LCD_SERIAL_PORT) + #error "ANYCUBIC_LCD_SERIAL_PORT is now LCD_SERIAL_PORT." +#elif defined(INTERNAL_SERIAL_PORT) + #error "INTERNAL_SERIAL_PORT is now MMU2_SERIAL_PORT." +#elif defined(X_DUAL_ENDSTOPS_ADJUSTMENT) || defined(Y_DUAL_ENDSTOPS_ADJUSTMENT) || defined(Z_DUAL_ENDSTOPS_ADJUSTMENT) + #error "[XYZ]_DUAL_ENDSTOPS_ADJUSTMENT is now [XYZ]2_ENDSTOP_ADJUSTMENT." +#elif defined(Z_TRIPLE_ENDSTOPS_ADJUSTMENT2) || defined(Z_TRIPLE_ENDSTOPS_ADJUSTMENT3) + #error "Z_TRIPLE_ENDSTOPS_ADJUSTMENT[23] is now Z[23]_ENDSTOP_ADJUSTMENT." +#elif defined(Z_QUAD_ENDSTOPS_ADJUSTMENT2) || defined(Z_QUAD_ENDSTOPS_ADJUSTMENT3) || defined(Z_QUAD_ENDSTOPS_ADJUSTMENT4) + #error "Z_QUAD_ENDSTOPS_ADJUSTMENT[234] is now Z[234]_ENDSTOP_ADJUSTMENT." +#elif defined(Z_DUAL_STEPPER_DRIVERS) + #error "Z_DUAL_STEPPER_DRIVERS is now NUM_Z_STEPPER_DRIVERS with a value of 2." +#elif defined(Z_TRIPLE_STEPPER_DRIVERS) + #error "Z_TRIPLE_STEPPER_DRIVERS is now NUM_Z_STEPPER_DRIVERS with a value of 3." +#elif defined(Z_QUAD_STEPPER_DRIVERS) + #error "Z_QUAD_STEPPER_DRIVERS is now NUM_Z_STEPPER_DRIVERS with a value of 4." +#elif defined(Z_DUAL_ENDSTOPS) || defined(Z_TRIPLE_ENDSTOPS) || defined(Z_QUAD_ENDSTOPS) + #error "Z_(DUAL|TRIPLE|QUAD)_ENDSTOPS is now Z_MULTI_ENDSTOPS." +#elif defined(DUGS_UI_MOVE_DIS_OPTION) + #error "DUGS_UI_MOVE_DIS_OPTION is spelled DGUS_UI_MOVE_DIS_OPTION." +#elif defined(ORIG_E0_AUTO_FAN_PIN) || defined(ORIG_E1_AUTO_FAN_PIN) || defined(ORIG_E2_AUTO_FAN_PIN) || defined(ORIG_E3_AUTO_FAN_PIN) || defined(ORIG_E4_AUTO_FAN_PIN) || defined(ORIG_E5_AUTO_FAN_PIN) || defined(ORIG_E6_AUTO_FAN_PIN) || defined(ORIG_E7_AUTO_FAN_PIN) + #error "ORIG_Ex_AUTO_FAN_PIN is now just Ex_AUTO_FAN_PIN." +#elif defined(ORIG_CHAMBER_AUTO_FAN_PIN) + #error "ORIG_CHAMBER_AUTO_FAN_PIN is now just CHAMBER_AUTO_FAN_PIN." +#elif defined(HOMING_BACKOFF_MM) + #error "HOMING_BACKOFF_MM is now HOMING_BACKOFF_POST_MM." +#elif defined(X_HOME_BUMP_MM) || defined(Y_HOME_BUMP_MM) || defined(Z_HOME_BUMP_MM) + #error "[XYZ]_HOME_BUMP_MM is now HOMING_BUMP_MM." +#elif defined(DIGIPOT_I2C) + #error "DIGIPOT_I2C is now DIGIPOT_MCP4451 (or DIGIPOT_MCP4018)." +#elif defined(TOUCH_BUTTONS) + #error "TOUCH_BUTTONS is now TOUCH_SCREEN." +#elif defined(LCD_FULL_PIXEL_HEIGHT) || defined(LCD_FULL_PIXEL_WIDTH) + #error "LCD_FULL_PIXEL_(WIDTH|HEIGHT) is deprecated and should be removed." +#elif defined(FSMC_UPSCALE) + #error "FSMC_UPSCALE is now GRAPHICAL_TFT_UPSCALE." +#elif defined(ANYCUBIC_TFT_MODEL) + #error "ANYCUBIC_TFT_MODEL is now ANYCUBIC_LCD_I3MEGA." +#elif defined(EVENT_GCODE_SD_STOP) + #error "EVENT_GCODE_SD_STOP is now EVENT_GCODE_SD_ABORT." +#elif defined(GRAPHICAL_TFT_ROTATE_180) + #error "GRAPHICAL_TFT_ROTATE_180 is now TFT_ROTATION set to TFT_ROTATE_180." +#elif defined(PROBE_OFFSET_START) + #error "PROBE_OFFSET_START is now PROBE_OFFSET_WIZARD_START_Z." +#elif defined(POWER_LOSS_PULL) + #error "POWER_LOSS_PULL is now specifically POWER_LOSS_PULL(UP|DOWN)." +#elif defined(SHORT_MANUAL_Z_MOVE) + #error "SHORT_MANUAL_Z_MOVE is now FINE_MANUAL_MOVE, applying to Z on most printers." +#elif defined(FIL_RUNOUT_INVERTING) + #if FIL_RUNOUT_INVERTING + #error "FIL_RUNOUT_INVERTING true is now FIL_RUNOUT_STATE HIGH." + #else + #error "FIL_RUNOUT_INVERTING false is now FIL_RUNOUT_STATE LOW." + #endif +#elif defined(ASSISTED_TRAMMING_MENU_ITEM) + #error "ASSISTED_TRAMMING_MENU_ITEM is deprecated and should be removed." +#endif + +/** + * Probe temp compensation requirements + */ +#if ENABLED(PROBE_TEMP_COMPENSATION) + #if defined(PTC_PARK_POS_X) || defined(PTC_PARK_POS_Y) || defined(PTC_PARK_POS_Z) + #error "PTC_PARK_POS_[XYZ] is now PTC_PARK_POS (array)." + #elif !defined(PTC_PARK_POS) + #error "PROBE_TEMP_COMPENSATION requires PTC_PARK_POS." + #elif defined(PTC_PROBE_POS_X) || defined(PTC_PROBE_POS_Y) + #error "PTC_PROBE_POS_[XY] is now PTC_PROBE_POS (array)." + #elif !defined(PTC_PROBE_POS) + #error "PROBE_TEMP_COMPENSATION requires PTC_PROBE_POS." + #endif +#endif + +/** + * Marlin release, version and default string + */ +#ifndef SHORT_BUILD_VERSION + #error "SHORT_BUILD_VERSION must be specified." +#elif !defined(DETAILED_BUILD_VERSION) + #error "BUILD_VERSION must be specified." +#elif !defined(STRING_DISTRIBUTION_DATE) + #error "STRING_DISTRIBUTION_DATE must be specified." +#elif !defined(PROTOCOL_VERSION) + #error "PROTOCOL_VERSION must be specified." +#elif !defined(MACHINE_NAME) + #error "MACHINE_NAME must be specified." +#elif !defined(SOURCE_CODE_URL) + #error "SOURCE_CODE_URL must be specified." +#elif !defined(DEFAULT_MACHINE_UUID) + #error "DEFAULT_MACHINE_UUID must be specified." +#elif !defined(WEBSITE_URL) + #error "WEBSITE_URL must be specified." +#endif + +/** + * Serial + */ +#ifndef SERIAL_PORT + #error "SERIAL_PORT must be defined." +#elif defined(SERIAL_PORT_2) && SERIAL_PORT_2 == SERIAL_PORT + #error "SERIAL_PORT_2 cannot be the same as SERIAL_PORT." +#endif +#if !(defined(__AVR__) && defined(USBCON)) + #if ENABLED(SERIAL_XON_XOFF) && RX_BUFFER_SIZE < 1024 + #error "SERIAL_XON_XOFF requires RX_BUFFER_SIZE >= 1024 for reliable transfers without drops." + #elif RX_BUFFER_SIZE && (RX_BUFFER_SIZE < 2 || !IS_POWER_OF_2(RX_BUFFER_SIZE)) + #error "RX_BUFFER_SIZE must be a power of 2 greater than 1." + #elif TX_BUFFER_SIZE && (TX_BUFFER_SIZE < 2 || TX_BUFFER_SIZE > 256 || !IS_POWER_OF_2(TX_BUFFER_SIZE)) + #error "TX_BUFFER_SIZE must be 0 or a power of 2 between 1 and 256." + #endif +#elif ANY(SERIAL_XON_XOFF, SERIAL_STATS_MAX_RX_QUEUED, SERIAL_STATS_DROPPED_RX) + #error "SERIAL_XON_XOFF and SERIAL_STATS_* features not supported on USB-native AVR devices." +#endif + +/** + * Multiple Stepper Drivers Per Axis + */ +#define GOOD_AXIS_PINS(A) (HAS_##A##_ENABLE && HAS_##A##_STEP && HAS_##A##_DIR) +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #if ENABLED(DUAL_X_CARRIAGE) + #error "DUAL_X_CARRIAGE is not compatible with X_DUAL_STEPPER_DRIVERS." + #elif !GOOD_AXIS_PINS(X) + #error "X_DUAL_STEPPER_DRIVERS requires X2 pins to be defined." + #endif +#endif + +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) && !GOOD_AXIS_PINS(Y) + #error "Y_DUAL_STEPPER_DRIVERS requires Y2 pins to be defined." +#elif !WITHIN(NUM_Z_STEPPER_DRIVERS, 1, 4) + #error "NUM_Z_STEPPER_DRIVERS must be an integer from 1 to 4." +#elif NUM_Z_STEPPER_DRIVERS == 2 && !GOOD_AXIS_PINS(Z2) + #error "If NUM_Z_STEPPER_DRIVERS is 2, you must define stepper pins for Z2." +#elif NUM_Z_STEPPER_DRIVERS == 3 && !(GOOD_AXIS_PINS(Z2) && GOOD_AXIS_PINS(Z3)) + #error "If NUM_Z_STEPPER_DRIVERS is 3, you must define stepper pins for Z2 and Z3." +#elif NUM_Z_STEPPER_DRIVERS == 4 && !(GOOD_AXIS_PINS(Z2) && GOOD_AXIS_PINS(Z3) && GOOD_AXIS_PINS(Z4)) + #error "If NUM_Z_STEPPER_DRIVERS is 4, you must define stepper pins for Z2, Z3, and Z4." +#endif + +/** + * Validate that the bed size fits + */ +static_assert(X_MAX_LENGTH >= X_BED_SIZE, "Movement bounds (X_MIN_POS, X_MAX_POS) are too narrow to contain X_BED_SIZE."); +static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS) are too narrow to contain Y_BED_SIZE."); + +/** + * Granular software endstops (Marlin >= 1.1.7) + */ +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) && DISABLED(MIN_SOFTWARE_ENDSTOP_Z) + #if IS_KINEMATIC + #error "MIN_SOFTWARE_ENDSTOPS on DELTA/SCARA also requires MIN_SOFTWARE_ENDSTOP_Z." + #elif NONE(MIN_SOFTWARE_ENDSTOP_X, MIN_SOFTWARE_ENDSTOP_Y) + #error "MIN_SOFTWARE_ENDSTOPS requires at least one of the MIN_SOFTWARE_ENDSTOP_[XYZ] options." + #endif +#endif + +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) && DISABLED(MAX_SOFTWARE_ENDSTOP_Z) + #if IS_KINEMATIC + #error "MAX_SOFTWARE_ENDSTOPS on DELTA/SCARA also requires MAX_SOFTWARE_ENDSTOP_Z." + #elif NONE(MAX_SOFTWARE_ENDSTOP_X, MAX_SOFTWARE_ENDSTOP_Y) + #error "MAX_SOFTWARE_ENDSTOPS requires at least one of the MAX_SOFTWARE_ENDSTOP_[XYZ] options." + #endif +#endif + +#if !defined(TARGET_LPC1768) && ANY( \ + ENDSTOPPULLDOWNS, \ + ENDSTOPPULLDOWN_XMAX, ENDSTOPPULLDOWN_YMAX, \ + ENDSTOPPULLDOWN_ZMAX, ENDSTOPPULLDOWN_XMIN, \ + ENDSTOPPULLDOWN_YMIN, ENDSTOPPULLDOWN_ZMIN \ + ) + #error "PULLDOWN pin mode is not available on the selected board." +#endif + +#if BOTH(ENDSTOPPULLUPS, ENDSTOPPULLDOWNS) + #error "Enable only one of ENDSTOPPULLUPS or ENDSTOPPULLDOWNS." +#elif BOTH(FIL_RUNOUT_PULLUP, FIL_RUNOUT_PULLDOWN) + #error "Enable only one of FIL_RUNOUT_PULLUP or FIL_RUNOUT_PULLDOWN." +#elif BOTH(ENDSTOPPULLUP_XMAX, ENDSTOPPULLDOWN_XMAX) + #error "Enable only one of ENDSTOPPULLUP_X_MAX or ENDSTOPPULLDOWN_X_MAX." +#elif BOTH(ENDSTOPPULLUP_YMAX, ENDSTOPPULLDOWN_YMAX) + #error "Enable only one of ENDSTOPPULLUP_Y_MAX or ENDSTOPPULLDOWN_Y_MAX." +#elif BOTH(ENDSTOPPULLUP_ZMAX, ENDSTOPPULLDOWN_ZMAX) + #error "Enable only one of ENDSTOPPULLUP_Z_MAX or ENDSTOPPULLDOWN_Z_MAX." +#elif BOTH(ENDSTOPPULLUP_XMIN, ENDSTOPPULLDOWN_XMIN) + #error "Enable only one of ENDSTOPPULLUP_X_MIN or ENDSTOPPULLDOWN_X_MIN." +#elif BOTH(ENDSTOPPULLUP_YMIN, ENDSTOPPULLDOWN_YMIN) + #error "Enable only one of ENDSTOPPULLUP_Y_MIN or ENDSTOPPULLDOWN_Y_MIN." +#elif BOTH(ENDSTOPPULLUP_ZMIN, ENDSTOPPULLDOWN_ZMIN) + #error "Enable only one of ENDSTOPPULLUP_Z_MIN or ENDSTOPPULLDOWN_Z_MIN." +#endif + +/** + * LCD Info Screen Style + */ +#if LCD_INFO_SCREEN_STYLE > 0 + #if HAS_MARLINUI_U8GLIB || LCD_WIDTH < 20 || LCD_HEIGHT < 4 + #error "Alternative LCD_INFO_SCREEN_STYLE requires 20x4 Character LCD." + #elif LCD_INFO_SCREEN_STYLE > 1 + #error "LCD_INFO_SCREEN_STYLE only has options 0 and 1 at this time." + #endif +#endif + +/** + * Progress Bar + */ +#if ENABLED(LCD_PROGRESS_BAR) + #if NONE(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) + #error "LCD_PROGRESS_BAR requires SDSUPPORT or LCD_SET_PROGRESS_MANUALLY." + #elif NONE(HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL) + #error "LCD_PROGRESS_BAR only applies to HD44780 character LCD and TFTGLCD_PANEL_(SPI|I2C)." + #elif HAS_MARLINUI_U8GLIB + #error "LCD_PROGRESS_BAR does not apply to graphical displays." + #elif ENABLED(FILAMENT_LCD_DISPLAY) + #error "LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both." + #elif PROGRESS_MSG_EXPIRE < 0 + #error "PROGRESS_MSG_EXPIRE must be greater than or equal to 0." + #endif +#elif ENABLED(LCD_SET_PROGRESS_MANUALLY) + #if NONE(HAS_MARLINUI_U8GLIB, HAS_GRAPHICAL_TFT, HAS_MARLINUI_HD44780, EXTENSIBLE_UI) + #error "LCD_SET_PROGRESS_MANUALLY requires LCD_PROGRESS_BAR, Character LCD, Graphical LCD, TFT, or EXTENSIBLE_UI." + #endif +#endif + +#if ENABLED(USE_M73_REMAINING_TIME) && DISABLED(LCD_SET_PROGRESS_MANUALLY) + #error "USE_M73_REMAINING_TIME requires LCD_SET_PROGRESS_MANUALLY" +#endif + +#if !HAS_LCD_MENU && ENABLED(SD_REPRINT_LAST_SELECTED_FILE) + #error "SD_REPRINT_LAST_SELECTED_FILE currently requires a Marlin-native LCD menu." +#endif + +/** + * Custom Boot and Status screens + */ +#if ENABLED(SHOW_CUSTOM_BOOTSCREEN) && NONE(HAS_MARLINUI_U8GLIB, TOUCH_UI_FTDI_EVE) + #error "SHOW_CUSTOM_BOOTSCREEN requires Graphical LCD or TOUCH_UI_FTDI_EVE." +#elif ENABLED(CUSTOM_STATUS_SCREEN_IMAGE) && !HAS_MARLINUI_U8GLIB + #error "CUSTOM_STATUS_SCREEN_IMAGE requires a 128x64 DOGM B/W Graphical LCD." +#endif + +/** + * LCD Lightweight Screen Style + */ +#if ENABLED(LIGHTWEIGHT_UI) && DISABLED(U8GLIB_ST7920) + #error "LIGHTWEIGHT_UI requires a U8GLIB_ST7920-based display." +#endif + +/** + * SD File Sorting + */ +#if ENABLED(SDCARD_SORT_ALPHA) + #if SDSORT_LIMIT > 256 + #error "SDSORT_LIMIT must be 256 or smaller." + #elif SDSORT_LIMIT < 10 + #error "SDSORT_LIMIT should be greater than 9 to be useful." + #elif DISABLED(SDSORT_USES_RAM) + #if ENABLED(SDSORT_DYNAMIC_RAM) + #error "SDSORT_DYNAMIC_RAM requires SDSORT_USES_RAM (which reads the directory into RAM)." + #elif ENABLED(SDSORT_CACHE_NAMES) + #error "SDSORT_CACHE_NAMES requires SDSORT_USES_RAM (which reads the directory into RAM)." + #endif + #endif + + #if ENABLED(SDSORT_CACHE_NAMES) && DISABLED(SDSORT_DYNAMIC_RAM) + #if SDSORT_CACHE_VFATS < 2 + #error "SDSORT_CACHE_VFATS must be 2 or greater!" + #elif SDSORT_CACHE_VFATS > MAX_VFAT_ENTRIES + #undef SDSORT_CACHE_VFATS + #define SDSORT_CACHE_VFATS MAX_VFAT_ENTRIES + #warning "SDSORT_CACHE_VFATS was reduced to MAX_VFAT_ENTRIES!" + #endif + #endif +#endif + +#if defined(EVENT_GCODE_SD_ABORT) && DISABLED(NOZZLE_PARK_FEATURE) + static_assert(nullptr == strstr(EVENT_GCODE_SD_ABORT, "G27"), "NOZZLE_PARK_FEATURE is required to use G27 in EVENT_GCODE_SD_ABORT."); +#endif + +/** + * I2C Position Encoders + */ +#if ENABLED(I2C_POSITION_ENCODERS) + #if !BOTH(BABYSTEPPING, BABYSTEP_XY) + #error "I2C_POSITION_ENCODERS requires BABYSTEPPING and BABYSTEP_XY." + #elif !WITHIN(I2CPE_ENCODER_CNT, 1, 5) + #error "I2CPE_ENCODER_CNT must be between 1 and 5." + #endif +#endif + +/** + * Babystepping + */ +#if ENABLED(BABYSTEPPING) + #if ENABLED(SCARA) + #error "BABYSTEPPING is not implemented for SCARA yet." + #elif BOTH(MARKFORGED_XY, BABYSTEP_XY) + #error "BABYSTEPPING only implemented for Z axis on MarkForged." + #elif BOTH(DELTA, BABYSTEP_XY) + #error "BABYSTEPPING only implemented for Z axis on deltabots." + #elif BOTH(BABYSTEP_ZPROBE_OFFSET, MESH_BED_LEVELING) + #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination" + #elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && !HAS_BED_PROBE + #error "BABYSTEP_ZPROBE_OFFSET requires a probe." + #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && !HAS_MARLINUI_U8GLIB + #error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a Graphical LCD." + #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && DISABLED(BABYSTEP_ZPROBE_OFFSET) + #error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a BABYSTEP_ZPROBE_OFFSET." + #elif ENABLED(BABYSTEP_HOTEND_Z_OFFSET) && !HAS_HOTEND_OFFSET + #error "BABYSTEP_HOTEND_Z_OFFSET requires 2 or more HOTENDS." + #elif BOTH(BABYSTEP_ALWAYS_AVAILABLE, MOVE_Z_WHEN_IDLE) + #error "BABYSTEP_ALWAYS_AVAILABLE and MOVE_Z_WHEN_IDLE are incompatible." + #elif !defined(BABYSTEP_MULTIPLICATOR_Z) + #error "BABYSTEPPING requires BABYSTEP_MULTIPLICATOR_Z." + #elif ENABLED(BABYSTEP_XY) && !defined(BABYSTEP_MULTIPLICATOR_XY) + #error "BABYSTEP_XY requires BABYSTEP_MULTIPLICATOR_XY." + #elif ENABLED(BABYSTEP_MILLIMETER_UNITS) + static_assert(BABYSTEP_MULTIPLICATOR_Z <= 0.1f, "BABYSTEP_MULTIPLICATOR_Z must be less or equal to 0.1mm."); + #if ENABLED(BABYSTEP_XY) + static_assert(BABYSTEP_MULTIPLICATOR_XY <= 0.25f, "BABYSTEP_MULTIPLICATOR_XY must be less than or equal to 0.25mm."); + #endif + #endif +#endif + +/** + * Filament Runout needs one or more pins and either SD Support or Auto print start detection + */ +#if HAS_FILAMENT_SENSOR + #if !PIN_EXISTS(FIL_RUNOUT) + #error "FILAMENT_RUNOUT_SENSOR requires FIL_RUNOUT_PIN." + #elif NUM_RUNOUT_SENSORS > E_STEPPERS + #if HAS_PRUSA_MMU2 + #error "NUM_RUNOUT_SENSORS must be 1 with MMU2 / MMU2S." + #else + #error "NUM_RUNOUT_SENSORS cannot exceed the number of E steppers." + #endif + #elif NUM_RUNOUT_SENSORS >= 2 && !PIN_EXISTS(FIL_RUNOUT2) + #error "FIL_RUNOUT2_PIN is required with NUM_RUNOUT_SENSORS >= 2." + #elif NUM_RUNOUT_SENSORS >= 3 && !PIN_EXISTS(FIL_RUNOUT3) + #error "FIL_RUNOUT3_PIN is required with NUM_RUNOUT_SENSORS >= 3." + #elif NUM_RUNOUT_SENSORS >= 4 && !PIN_EXISTS(FIL_RUNOUT4) + #error "FIL_RUNOUT4_PIN is required with NUM_RUNOUT_SENSORS >= 4." + #elif NUM_RUNOUT_SENSORS >= 5 && !PIN_EXISTS(FIL_RUNOUT5) + #error "FIL_RUNOUT5_PIN is required with NUM_RUNOUT_SENSORS >= 5." + #elif NUM_RUNOUT_SENSORS >= 6 && !PIN_EXISTS(FIL_RUNOUT6) + #error "FIL_RUNOUT6_PIN is required with NUM_RUNOUT_SENSORS >= 6." + #elif NUM_RUNOUT_SENSORS >= 7 && !PIN_EXISTS(FIL_RUNOUT7) + #error "FIL_RUNOUT7_PIN is required with NUM_RUNOUT_SENSORS >= 7." + #elif NUM_RUNOUT_SENSORS >= 8 && !PIN_EXISTS(FIL_RUNOUT8) + #error "FIL_RUNOUT8_PIN is required with NUM_RUNOUT_SENSORS >= 8." + #elif BOTH(FIL_RUNOUT1_PULLUP, FIL_RUNOUT1_PULLDOWN) + #error "You can't enable FIL_RUNOUT1_PULLUP and FIL_RUNOUT1_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT2_PULLUP, FIL_RUNOUT2_PULLDOWN) + #error "You can't enable FIL_RUNOUT2_PULLUP and FIL_RUNOUT2_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT3_PULLUP, FIL_RUNOUT3_PULLDOWN) + #error "You can't enable FIL_RUNOUT3_PULLUP and FIL_RUNOUT3_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT4_PULLUP, FIL_RUNOUT4_PULLDOWN) + #error "You can't enable FIL_RUNOUT4_PULLUP and FIL_RUNOUT4_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT5_PULLUP, FIL_RUNOUT5_PULLDOWN) + #error "You can't enable FIL_RUNOUT5_PULLUP and FIL_RUNOUT5_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT6_PULLUP, FIL_RUNOUT6_PULLDOWN) + #error "You can't enable FIL_RUNOUT6_PULLUP and FIL_RUNOUT6_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT7_PULLUP, FIL_RUNOUT7_PULLDOWN) + #error "You can't enable FIL_RUNOUT7_PULLUP and FIL_RUNOUT7_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT8_PULLUP, FIL_RUNOUT8_PULLDOWN) + #error "You can't enable FIL_RUNOUT8_PULLUP and FIL_RUNOUT8_PULLDOWN at the same time." + #elif FILAMENT_RUNOUT_DISTANCE_MM < 0 + #error "FILAMENT_RUNOUT_DISTANCE_MM must be greater than or equal to zero." + #elif DISABLED(ADVANCED_PAUSE_FEATURE) + static_assert(nullptr == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR."); + #endif +#endif + +/** + * Advanced Pause + */ +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #if !HAS_RESUME_CONTINUE + #error "ADVANCED_PAUSE_FEATURE requires a supported LCD controller (or EMERGENCY_PARSER)." + #elif DISABLED(NOZZLE_PARK_FEATURE) + #error "ADVANCED_PAUSE_FEATURE requires NOZZLE_PARK_FEATURE." + #elif !defined(FILAMENT_UNLOAD_PURGE_FEEDRATE) + #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE." + #elif ENABLED(EXTRUDER_RUNOUT_PREVENT) + #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE." + #elif ENABLED(PARK_HEAD_ON_PAUSE) && NONE(SDSUPPORT, IS_NEWPANEL, EMERGENCY_PARSER) + #error "PARK_HEAD_ON_PAUSE requires SDSUPPORT, EMERGENCY_PARSER, or an LCD controller." + #elif ENABLED(HOME_BEFORE_FILAMENT_CHANGE) && DISABLED(PAUSE_PARK_NO_STEPPER_TIMEOUT) + #error "HOME_BEFORE_FILAMENT_CHANGE requires PAUSE_PARK_NO_STEPPER_TIMEOUT." + #elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_UNLOAD_LENGTH > EXTRUDE_MAXLENGTH + #error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH." + #elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_SLOW_LOAD_LENGTH > EXTRUDE_MAXLENGTH + #error "FILAMENT_CHANGE_SLOW_LOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH." + #elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_FAST_LOAD_LENGTH > EXTRUDE_MAXLENGTH + #error "FILAMENT_CHANGE_FAST_LOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH." + #endif +#endif + +#if ENABLED(NOZZLE_PARK_FEATURE) + constexpr float npp[] = NOZZLE_PARK_POINT; + static_assert(COUNT(npp) == XYZ, "NOZZLE_PARK_POINT requires X, Y, and Z values."); + constexpr xyz_pos_t npp_xyz = NOZZLE_PARK_POINT; + static_assert(WITHIN(npp_xyz.x, X_MIN_POS, X_MAX_POS), "NOZZLE_PARK_POINT.X is out of bounds (X_MIN_POS, X_MAX_POS)."); + static_assert(WITHIN(npp_xyz.y, Y_MIN_POS, Y_MAX_POS), "NOZZLE_PARK_POINT.Y is out of bounds (Y_MIN_POS, Y_MAX_POS)."); + static_assert(WITHIN(npp_xyz.z, Z_MIN_POS, Z_MAX_POS), "NOZZLE_PARK_POINT.Z is out of bounds (Z_MIN_POS, Z_MAX_POS)."); +#endif + +/** + * Individual axis homing is useless for DELTAS + */ +#if BOTH(INDIVIDUAL_AXIS_HOMING_MENU, DELTA) + #error "INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics." +#endif + +/** + * Sanity checking for all Průša MMU + */ +#ifdef SNMM + #error "SNMM is obsolete. Define MMU_MODEL as PRUSA_MMU1 instead." +#elif ENABLED(MK2_MULTIPLEXER) + #error "MK2_MULTIPLEXER is obsolete. Define MMU_MODEL as PRUSA_MMU1 instead." +#elif ENABLED(PRUSA_MMU2) + #error "PRUSA_MMU2 is obsolete. Define MMU_MODEL as PRUSA_MMU2 instead." +#elif ENABLED(PRUSA_MMU2_S_MODE) + #error "PRUSA_MMU2_S_MODE is obsolete. Define MMU_MODEL as PRUSA_MMU2S instead." +#endif + +/** + * Multi-Material-Unit 2 / SMUFF requirements + */ +#if HAS_PRUSA_MMU2 + #if EXTRUDERS != 5 + #undef SINGLENOZZLE + #error "PRUSA_MMU2(S) requires exactly 5 EXTRUDERS. Please update your Configuration." + #elif DISABLED(NOZZLE_PARK_FEATURE) + #error "PRUSA_MMU2(S) requires NOZZLE_PARK_FEATURE. Enable it to continue." + #elif HAS_PRUSA_MMU2S && DISABLED(FILAMENT_RUNOUT_SENSOR) + #error "PRUSA_MMU2S requires FILAMENT_RUNOUT_SENSOR. Enable it to continue." + #elif ENABLED(MMU_EXTRUDER_SENSOR) && DISABLED(FILAMENT_RUNOUT_SENSOR) + #error "MMU_EXTRUDER_SENSOR requires FILAMENT_RUNOUT_SENSOR. Enable it to continue." + #elif ENABLED(MMU_EXTRUDER_SENSOR) && !HAS_LCD_MENU + #error "MMU_EXTRUDER_SENSOR requires an LCD supporting MarlinUI to be enabled." + #elif DISABLED(ADVANCED_PAUSE_FEATURE) + static_assert(nullptr == strstr(MMU2_FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with PRUSA_MMU2(S) / SMUFF_EMU_MMU2(S)."); + #endif +#endif +#if HAS_SMUFF && EXTRUDERS > 12 + #error "Too many extruders for SMUFF_EMU_MMU2(S). (12 maximum)." +#endif + +/** + * Options only for EXTRUDERS > 1 + */ +#if HAS_MULTI_EXTRUDER + + #if EXTRUDERS > 8 + #error "Marlin supports a maximum of 8 EXTRUDERS." + #endif + + #if ENABLED(HEATERS_PARALLEL) + #error "EXTRUDERS must be 1 with HEATERS_PARALLEL." + #endif + + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #ifndef TOOLCHANGE_FS_LENGTH + #error "TOOLCHANGE_FILAMENT_SWAP requires TOOLCHANGE_FS_LENGTH." + #elif !defined(TOOLCHANGE_FS_RETRACT_SPEED) + #error "TOOLCHANGE_FILAMENT_SWAP requires TOOLCHANGE_FS_RETRACT_SPEED." + #elif !defined(TOOLCHANGE_FS_PRIME_SPEED) + #error "TOOLCHANGE_FILAMENT_SWAP requires TOOLCHANGE_FS_PRIME_SPEED." + #endif + #endif + + #if ENABLED(TOOLCHANGE_PARK) + #ifndef TOOLCHANGE_PARK_XY + #error "TOOLCHANGE_PARK requires TOOLCHANGE_PARK_XY." + #elif !defined(TOOLCHANGE_PARK_XY_FEEDRATE) + #error "TOOLCHANGE_PARK requires TOOLCHANGE_PARK_XY_FEEDRATE." + #endif + #endif + + #ifndef TOOLCHANGE_ZRAISE + #error "TOOLCHANGE_ZRAISE required for EXTRUDERS > 1." + #endif + +#elif HAS_PRUSA_MMU1 || HAS_SMUFF + + #error "Multi-Material-Unit requires 2 or more EXTRUDERS." + +#elif ENABLED(SINGLENOZZLE) + + #error "SINGLENOZZLE requires 2 or more EXTRUDERS." + +#endif + +/** + * A Dual Nozzle carriage with switching servo + */ +#if ENABLED(SWITCHING_NOZZLE) + #if ENABLED(DUAL_X_CARRIAGE) + #error "SWITCHING_NOZZLE and DUAL_X_CARRIAGE are incompatible." + #elif ENABLED(SINGLENOZZLE) + #error "SWITCHING_NOZZLE and SINGLENOZZLE are incompatible." + #elif EXTRUDERS != 2 + #error "SWITCHING_NOZZLE requires exactly 2 EXTRUDERS." + #elif NUM_SERVOS < 1 + #error "SWITCHING_NOZZLE requires NUM_SERVOS >= 1." + #endif + + #ifndef SWITCHING_NOZZLE_SERVO_NR + #error "SWITCHING_NOZZLE requires SWITCHING_NOZZLE_SERVO_NR." + #elif SWITCHING_NOZZLE_SERVO_NR == 0 && !PIN_EXISTS(SERVO0) + #error "SERVO0_PIN must be defined for your SWITCHING_NOZZLE." + #elif SWITCHING_NOZZLE_SERVO_NR == 1 && !PIN_EXISTS(SERVO1) + #error "SERVO1_PIN must be defined for your SWITCHING_NOZZLE." + #elif SWITCHING_NOZZLE_SERVO_NR == 2 && !PIN_EXISTS(SERVO2) + #error "SERVO2_PIN must be defined for your SWITCHING_NOZZLE." + #elif SWITCHING_NOZZLE_SERVO_NR == 3 && !PIN_EXISTS(SERVO3) + #error "SERVO3_PIN must be defined for your SWITCHING_NOZZLE." + #endif + + #ifdef SWITCHING_NOZZLE_E1_SERVO_NR + #if SWITCHING_NOZZLE_E1_SERVO_NR == SWITCHING_NOZZLE_SERVO_NR + #error "SWITCHING_NOZZLE_E1_SERVO_NR must be different from SWITCHING_NOZZLE_SERVO_NR." + #elif SWITCHING_NOZZLE_E1_SERVO_NR == 0 && !PIN_EXISTS(SERVO0) + #error "SERVO0_PIN must be defined for your SWITCHING_NOZZLE." + #elif SWITCHING_NOZZLE_E1_SERVO_NR == 1 && !PIN_EXISTS(SERVO1) + #error "SERVO1_PIN must be defined for your SWITCHING_NOZZLE." + #elif SWITCHING_NOZZLE_E1_SERVO_NR == 2 && !PIN_EXISTS(SERVO2) + #error "SERVO2_PIN must be defined for your SWITCHING_NOZZLE." + #elif SWITCHING_NOZZLE_E1_SERVO_NR == 3 && !PIN_EXISTS(SERVO3) + #error "SERVO3_PIN must be defined for your SWITCHING_NOZZLE." + #endif + #endif +#endif + +/** + * Single Stepper Dual Extruder with switching servo + */ +#if ENABLED(SWITCHING_EXTRUDER) + #if NUM_SERVOS < 1 + #error "SWITCHING_EXTRUDER requires NUM_SERVOS >= 1." + #elif SWITCHING_EXTRUDER_SERVO_NR == 0 && !PIN_EXISTS(SERVO0) + #error "SERVO0_PIN must be defined for your SWITCHING_EXTRUDER." + #elif SWITCHING_EXTRUDER_SERVO_NR == 1 && !PIN_EXISTS(SERVO1) + #error "SERVO1_PIN must be defined for your SWITCHING_EXTRUDER." + #elif SWITCHING_EXTRUDER_SERVO_NR == 2 && !PIN_EXISTS(SERVO2) + #error "SERVO2_PIN must be defined for your SWITCHING_EXTRUDER." + #elif SWITCHING_EXTRUDER_SERVO_NR == 3 && !PIN_EXISTS(SERVO3) + #error "SERVO3_PIN must be defined for your SWITCHING_EXTRUDER." + #endif + #if EXTRUDERS > 3 + #if NUM_SERVOS < 2 + #error "SWITCHING_EXTRUDER with 4 extruders requires NUM_SERVOS >= 2." + #elif SWITCHING_EXTRUDER_E23_SERVO_NR == 0 && !PIN_EXISTS(SERVO0) + #error "SERVO0_PIN must be defined for your SWITCHING_EXTRUDER." + #elif SWITCHING_EXTRUDER_E23_SERVO_NR == 1 && !PIN_EXISTS(SERVO1) + #error "SERVO1_PIN must be defined for your SWITCHING_EXTRUDER." + #elif SWITCHING_EXTRUDER_E23_SERVO_NR == 2 && !PIN_EXISTS(SERVO2) + #error "SERVO2_PIN must be defined for your SWITCHING_EXTRUDER." + #elif SWITCHING_EXTRUDER_E23_SERVO_NR == 3 && !PIN_EXISTS(SERVO3) + #error "SERVO3_PIN must be defined for your SWITCHING_EXTRUDER." + #elif SWITCHING_EXTRUDER_E23_SERVO_NR == SWITCHING_EXTRUDER_SERVO_NR + #error "SWITCHING_EXTRUDER_E23_SERVO_NR should be a different extruder from SWITCHING_EXTRUDER_SERVO_NR." + #endif + #endif +#endif + +/** + * Mixing Extruder requirements + */ +#if ENABLED(MIXING_EXTRUDER) + #if HAS_MULTI_EXTRUDER + #error "For MIXING_EXTRUDER set MIXING_STEPPERS > 1 instead of EXTRUDERS > 1." + #elif MIXING_STEPPERS < 2 + #error "You must set MIXING_STEPPERS >= 2 for a mixing extruder." + #elif ENABLED(FILAMENT_SENSOR) + #error "MIXING_EXTRUDER is incompatible with FILAMENT_SENSOR. Comment out this line to use it anyway." + #elif ENABLED(SWITCHING_EXTRUDER) + #error "Please select either MIXING_EXTRUDER or SWITCHING_EXTRUDER, not both." + #elif ENABLED(SINGLENOZZLE) + #error "MIXING_EXTRUDER is incompatible with SINGLENOZZLE." + #endif +#endif + +/** + * Linear Advance 1.5 - Check K value range + */ +#if ENABLED(LIN_ADVANCE) + static_assert( + WITHIN(LIN_ADVANCE_K, 0, 10), + "LIN_ADVANCE_K must be a value from 0 to 10 (Changed in LIN_ADVANCE v1.5, Marlin 1.1.9)." + ); + #if ENABLED(S_CURVE_ACCELERATION) && DISABLED(EXPERIMENTAL_SCURVE) + #error "LIN_ADVANCE and S_CURVE_ACCELERATION may not play well together! Enable EXPERIMENTAL_SCURVE to continue." + #endif +#endif + +/** + * Special tool-changing options + */ +#if MANY(SINGLENOZZLE, DUAL_X_CARRIAGE, PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER, SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #error "Please select only one of SINGLENOZZLE, DUAL_X_CARRIAGE, PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER, SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, or ELECTROMAGNETIC_SWITCHING_TOOLHEAD." +#endif + +/** + * (Magnetic) Parking Extruder requirements + */ +#if ANY(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) + #if ENABLED(EXT_SOLENOID) + #error "(MAGNETIC_)PARKING_EXTRUDER and EXT_SOLENOID are incompatible. (Pins are used twice.)" + #elif EXTRUDERS != 2 + #error "(MAGNETIC_)PARKING_EXTRUDER requires exactly 2 EXTRUDERS." + #elif !defined(PARKING_EXTRUDER_PARKING_X) + #error "(MAGNETIC_)PARKING_EXTRUDER requires PARKING_EXTRUDER_PARKING_X." + #elif !defined(TOOLCHANGE_ZRAISE) + #error "(MAGNETIC_)PARKING_EXTRUDER requires TOOLCHANGE_ZRAISE." + #elif TOOLCHANGE_ZRAISE < 0 + #error "TOOLCHANGE_ZRAISE must be 0 or higher." + #elif ENABLED(PARKING_EXTRUDER) + #if !PINS_EXIST(SOL0, SOL1) + #error "PARKING_EXTRUDER requires SOL0_PIN and SOL1_PIN." + #elif !defined(PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE) || !WITHIN(PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE, LOW, HIGH) + #error "PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE must be defined as HIGH or LOW." + #elif !defined(PARKING_EXTRUDER_SOLENOIDS_DELAY) || !WITHIN(PARKING_EXTRUDER_SOLENOIDS_DELAY, 0, 2000) + #error "PARKING_EXTRUDER_SOLENOIDS_DELAY must be between 0 and 2000 (ms)." + #endif + #endif +#endif + +/** + * Switching Toolhead requirements + */ +#if ENABLED(SWITCHING_TOOLHEAD) + #ifndef SWITCHING_TOOLHEAD_SERVO_NR + #error "SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_SERVO_NR." + #elif EXTRUDERS < 2 + #error "SWITCHING_TOOLHEAD requires at least 2 EXTRUDERS." + #elif NUM_SERVOS < (SWITCHING_TOOLHEAD_SERVO_NR - 1) + #if SWITCHING_TOOLHEAD_SERVO_NR == 0 + #error "A SWITCHING_TOOLHEAD_SERVO_NR of 0 requires NUM_SERVOS >= 1." + #elif SWITCHING_TOOLHEAD_SERVO_NR == 1 + #error "A SWITCHING_TOOLHEAD_SERVO_NR of 1 requires NUM_SERVOS >= 2." + #elif SWITCHING_TOOLHEAD_SERVO_NR == 2 + #error "A SWITCHING_TOOLHEAD_SERVO_NR of 2 requires NUM_SERVOS >= 3." + #elif SWITCHING_TOOLHEAD_SERVO_NR == 3 + #error "A SWITCHING_TOOLHEAD_SERVO_NR of 3 requires NUM_SERVOS >= 4." + #endif + #elif !defined(TOOLCHANGE_ZRAISE) + #error "SWITCHING_TOOLHEAD requires TOOLCHANGE_ZRAISE." + #elif TOOLCHANGE_ZRAISE < 0 + #error "TOOLCHANGE_ZRAISE must be 0 or higher." + #endif +#endif + +/** + * (Electro)magnetic Switching Toolhead requirements + */ +#if EITHER(MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #ifndef SWITCHING_TOOLHEAD_Y_POS + #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Y_POS" + #elif !defined(SWITCHING_TOOLHEAD_X_POS) + #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_X_POS" + #elif !defined(SWITCHING_TOOLHEAD_Z_HOP) + #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Z_HOP." + #elif !defined(SWITCHING_TOOLHEAD_Y_CLEAR) + #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Y_CLEAR." + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #if ENABLED(EXT_SOLENOID) + #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD and EXT_SOLENOID are incompatible. (Pins are used twice.)" + #elif !PIN_EXISTS(SOL0) + #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SOL0_PIN." + #endif + #endif +#endif + +/** + * Part-Cooling Fan Multiplexer requirements + */ +#if PIN_EXISTS(FANMUX1) + #if !HAS_FANMUX + #error "FANMUX0_PIN must be set before FANMUX1_PIN can be set." + #endif +#elif PIN_EXISTS(FANMUX2) + #error "FANMUX0_PIN and FANMUX1_PIN must be set before FANMUX2_PIN can be set." +#endif + +/** + * Limited user-controlled fans + */ +#if NUM_M106_FANS > FAN_COUNT + #error "The selected board doesn't support enough user-controlled fans. Reduce NUM_M106_FANS." +#endif + +/** + * Limited number of servos + */ +#if NUM_SERVOS > NUM_SERVO_PLUGS + #error "The selected board doesn't support enough servos for your configuration. Reduce NUM_SERVOS." +#endif + +/** + * Servo deactivation depends on servo endstops, switching nozzle, or switching extruder + */ +#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) && !HAS_Z_SERVO_PROBE && !defined(SWITCHING_NOZZLE_SERVO_NR) && !defined(SWITCHING_EXTRUDER_SERVO_NR) && !defined(SWITCHING_TOOLHEAD_SERVO_NR) + #error "Z_PROBE_SERVO_NR, switching nozzle, switching toolhead or switching extruder is required for DEACTIVATE_SERVOS_AFTER_MOVE." +#endif + +/** + * Required LCD language + */ +#if HAS_MARLINUI_HD44780 && !defined(DISPLAY_CHARSET_HD44780) + #error "You must set DISPLAY_CHARSET_HD44780 to JAPANESE, WESTERN or CYRILLIC for your LCD controller." +#endif + +/** + * Bed Heating Options - PID vs Limit Switching + */ +#if BOTH(PIDTEMPBED, BED_LIMIT_SWITCHING) + #error "To use BED_LIMIT_SWITCHING you must disable PIDTEMPBED." +#endif + +/** + * Kinematics + */ + +/** + * Allow only one kinematic type to be defined + */ +#if MANY(DELTA, MORGAN_SCARA, COREXY, COREXZ, COREYZ, COREYX, COREZX, COREZY, MARKFORGED_XY) + #error "Please enable only one of DELTA, MORGAN_SCARA, COREXY, COREYX, COREXZ, COREZX, COREYZ, COREZY, or MARKFORGED_XY." +#endif + +/** + * Delta requirements + */ +#if ENABLED(DELTA) + #if NONE(USE_XMAX_PLUG, USE_YMAX_PLUG, USE_ZMAX_PLUG) + #error "You probably want to use Max Endstops for DELTA!" + #elif ENABLED(ENABLE_LEVELING_FADE_HEIGHT) && DISABLED(AUTO_BED_LEVELING_BILINEAR) && !UBL_SEGMENTED + #error "ENABLE_LEVELING_FADE_HEIGHT on DELTA requires AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL." + #elif ENABLED(DELTA_AUTO_CALIBRATION) && !(HAS_BED_PROBE || HAS_LCD_MENU) + #error "DELTA_AUTO_CALIBRATION requires a probe or LCD Controller." + #elif ENABLED(DELTA_CALIBRATION_MENU) && !HAS_LCD_MENU + #error "DELTA_CALIBRATION_MENU requires an LCD Controller." + #elif ABL_GRID + #if (GRID_MAX_POINTS_X & 1) == 0 || (GRID_MAX_POINTS_Y & 1) == 0 + #error "DELTA requires GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y to be odd numbers." + #elif GRID_MAX_POINTS_X < 3 + #error "DELTA requires GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y to be 3 or higher." + #endif + #endif +#endif + +/** + * Junction deviation is incompatible with kinematic systems. + */ +#if HAS_JUNCTION_DEVIATION && IS_KINEMATIC + #error "CLASSIC_JERK is required for DELTA and SCARA." +#endif + +/** + * Probes + */ + +/** + * Allow only one probe option to be defined + */ +#if 1 < 0 \ + + (DISABLED(BLTOUCH) && HAS_Z_SERVO_PROBE) \ + + COUNT_ENABLED(PROBE_MANUALLY, BLTOUCH, FIX_MOUNTED_PROBE, NOZZLE_AS_PROBE, TOUCH_MI_PROBE, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, RACK_AND_PINION_PROBE, SENSORLESS_PROBING) + #error "Please enable only one probe option: PROBE_MANUALLY, SENSORLESS_PROBING, BLTOUCH, FIX_MOUNTED_PROBE, NOZZLE_AS_PROBE, TOUCH_MI_PROBE, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or Z Servo." +#endif + +#if HAS_BED_PROBE + + /** + * Z_PROBE_SLED is incompatible with DELTA + */ + #if BOTH(Z_PROBE_SLED, DELTA) + #error "You cannot use Z_PROBE_SLED with DELTA." + #endif + + /** + * SOLENOID_PROBE requirements + */ + #if ENABLED(SOLENOID_PROBE) + #if ENABLED(EXT_SOLENOID) + #error "SOLENOID_PROBE is incompatible with EXT_SOLENOID." + #elif !HAS_SOLENOID_1 + #error "SOLENOID_PROBE requires SOL1_PIN." + #endif + #endif + + /** + * NUM_SERVOS is required for a Z servo probe + */ + #if HAS_Z_SERVO_PROBE + #if !NUM_SERVOS + #error "NUM_SERVOS is required for a Z servo probe (Z_PROBE_SERVO_NR)." + #elif Z_PROBE_SERVO_NR >= NUM_SERVOS + #error "Z_PROBE_SERVO_NR must be smaller than NUM_SERVOS." + #elif Z_PROBE_SERVO_NR == 0 && !PIN_EXISTS(SERVO0) + #error "SERVO0_PIN must be defined for your servo or BLTOUCH probe." + #elif Z_PROBE_SERVO_NR == 1 && !PIN_EXISTS(SERVO1) + #error "SERVO1_PIN must be defined for your servo or BLTOUCH probe." + #elif Z_PROBE_SERVO_NR == 2 && !PIN_EXISTS(SERVO2) + #error "SERVO2_PIN must be defined for your servo or BLTOUCH probe." + #elif Z_PROBE_SERVO_NR == 3 && !PIN_EXISTS(SERVO3) + #error "SERVO3_PIN must be defined for your servo or BLTOUCH probe." + #endif + #endif + + #if ENABLED(BLTOUCH) + #if BLTOUCH_DELAY < 200 + #error "BLTOUCH_DELAY less than 200 is unsafe and is not supported." + #elif DISABLED(BLTOUCH_SET_5V_MODE) && NONE(ONBOARD_ENDSTOPPULLUPS, ENDSTOPPULLUPS, ENDSTOPPULLUP_ZMIN, ENDSTOPPULLUP_ZMIN_PROBE) + #error "BLTOUCH without BLTOUCH_SET_5V_MODE requires ENDSTOPPULLUPS, ENDSTOPPULLUP_ZMIN or ENDSTOPPULLUP_ZMIN_PROBE." + #endif + #endif + + #if ENABLED(RACK_AND_PINION_PROBE) && !(defined(Z_PROBE_DEPLOY_X) && defined(Z_PROBE_RETRACT_X)) + #error "RACK_AND_PINION_PROBE requires Z_PROBE_DEPLOY_X and Z_PROBE_RETRACT_X." + #endif + + /** + * Touch-MI probe requirements + */ + #if ENABLED(TOUCH_MI_PROBE) + #if DISABLED(Z_SAFE_HOMING) + #error "TOUCH_MI_PROBE requires Z_SAFE_HOMING." + #elif !defined(TOUCH_MI_RETRACT_Z) + #error "TOUCH_MI_PROBE requires TOUCH_MI_RETRACT_Z." + #elif defined(Z_AFTER_PROBING) + #error "TOUCH_MI_PROBE requires Z_AFTER_PROBING to be disabled." + #elif Z_HOMING_HEIGHT < 10 + #error "TOUCH_MI_PROBE requires Z_HOMING_HEIGHT >= 10." + #elif Z_MIN_PROBE_ENDSTOP_INVERTING + #error "TOUCH_MI_PROBE requires Z_MIN_PROBE_ENDSTOP_INVERTING to be set to false." + #elif DISABLED(BABYSTEP_ZPROBE_OFFSET) + #error "TOUCH_MI_PROBE requires BABYSTEPPING with BABYSTEP_ZPROBE_OFFSET." + #elif !HAS_RESUME_CONTINUE + #error "TOUCH_MI_PROBE currently requires an LCD controller or EMERGENCY_PARSER." + #endif + #endif + + /** + * Require pin options and pins to be defined + */ + #if ENABLED(SENSORLESS_PROBING) + #if ENABLED(DELTA) && !(AXIS_HAS_STALLGUARD(X) && AXIS_HAS_STALLGUARD(Y) && AXIS_HAS_STALLGUARD(Z)) + #error "SENSORLESS_PROBING requires TMC2130/2160/2209/5130/5160 drivers on X, Y, and Z." + #elif !AXIS_HAS_STALLGUARD(Z) + #error "SENSORLESS_PROBING requires a TMC2130/2160/2209/5130/5160 driver on Z." + #endif + #elif ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) + #if DISABLED(USE_ZMIN_PLUG) + #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires USE_ZMIN_PLUG to be enabled." + #elif !HAS_Z_MIN + #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires the Z_MIN_PIN to be defined." + #elif Z_MIN_PROBE_ENDSTOP_INVERTING != Z_MIN_ENDSTOP_INVERTING + #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires Z_MIN_ENDSTOP_INVERTING to match Z_MIN_PROBE_ENDSTOP_INVERTING." + #endif + #elif !HAS_Z_MIN_PROBE_PIN + #error "Z_MIN_PROBE_PIN must be defined if Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN is not enabled." + #endif + + /** + * Check for improper NOZZLE_TO_PROBE_OFFSET + */ + constexpr xyz_pos_t sanity_nozzle_to_probe_offset = NOZZLE_TO_PROBE_OFFSET; + #if ENABLED(NOZZLE_AS_PROBE) + static_assert(sanity_nozzle_to_probe_offset.x == 0 && sanity_nozzle_to_probe_offset.y == 0, + "NOZZLE_AS_PROBE requires the XY offsets in NOZZLE_TO_PROBE_OFFSET to both be 0."); + #else + static_assert(PROBING_MARGIN >= 0, "PROBING_MARGIN must be >= 0."); + static_assert(PROBING_MARGIN_BACK >= 0, "PROBING_MARGIN_BACK must be >= 0."); + static_assert(PROBING_MARGIN_FRONT >= 0, "PROBING_MARGIN_FRONT must be >= 0."); + static_assert(PROBING_MARGIN_LEFT >= 0, "PROBING_MARGIN_LEFT must be >= 0."); + static_assert(PROBING_MARGIN_RIGHT >= 0, "PROBING_MARGIN_RIGHT must be >= 0."); + #endif + + #define _MARGIN(A) TERN(IS_SCARA, SCARA_PRINTABLE_RADIUS, TERN(DELTA, DELTA_PRINTABLE_RADIUS, ((A##_BED_SIZE) / 2))) + static_assert(PROBING_MARGIN < _MARGIN(X), "PROBING_MARGIN is too large."); + static_assert(PROBING_MARGIN_BACK < _MARGIN(Y), "PROBING_MARGIN_BACK is too large."); + static_assert(PROBING_MARGIN_FRONT < _MARGIN(Y), "PROBING_MARGIN_FRONT is too large."); + static_assert(PROBING_MARGIN_LEFT < _MARGIN(X), "PROBING_MARGIN_LEFT is too large."); + static_assert(PROBING_MARGIN_RIGHT < _MARGIN(X), "PROBING_MARGIN_RIGHT is too large."); + #undef _MARGIN + + /** + * Make sure Z raise values are set + */ + #ifndef Z_CLEARANCE_DEPLOY_PROBE + #error "You must define Z_CLEARANCE_DEPLOY_PROBE in your configuration." + #elif !defined(Z_CLEARANCE_BETWEEN_PROBES) + #error "You must define Z_CLEARANCE_BETWEEN_PROBES in your configuration." + #elif Z_CLEARANCE_DEPLOY_PROBE < 0 + #error "Probes need Z_CLEARANCE_DEPLOY_PROBE >= 0." + #elif Z_CLEARANCE_BETWEEN_PROBES < 0 + #error "Probes need Z_CLEARANCE_BETWEEN_PROBES >= 0." + #elif Z_AFTER_PROBING < 0 + #error "Probes need Z_AFTER_PROBING >= 0." + #endif + + #if MULTIPLE_PROBING > 0 || EXTRA_PROBING > 0 + #if MULTIPLE_PROBING == 0 + #error "EXTRA_PROBING requires MULTIPLE_PROBING." + #elif MULTIPLE_PROBING < 2 + #error "MULTIPLE_PROBING must be 2 or more." + #elif MULTIPLE_PROBING <= EXTRA_PROBING + #error "EXTRA_PROBING must be less than MULTIPLE_PROBING." + #endif + #endif + + #if Z_PROBE_LOW_POINT > 0 + #error "Z_PROBE_LOW_POINT must be less than or equal to 0." + #endif + + #if HOMING_Z_WITH_PROBE && IS_CARTESIAN && DISABLED(Z_SAFE_HOMING) + #error "Z_SAFE_HOMING is recommended when homing with a probe. Enable it or comment out this line to continue." + #endif + + #if ENABLED(PROBE_ACTIVATION_SWITCH) + #ifndef PROBE_ACTIVATION_SWITCH_STATE + #error "PROBE_ACTIVATION_SWITCH_STATE is required for PROBE_ACTIVATION_SWITCH." + #elif !PIN_EXISTS(PROBE_ACTIVATION_SWITCH) + #error "A PROBE_ACTIVATION_SWITCH_PIN is required for PROBE_ACTIVATION_SWITCH." + #endif + #endif + +#else + + /** + * Require some kind of probe for bed leveling and probe testing + */ + #if HAS_ABL_NOT_UBL && !PROBE_SELECTED + #error "Auto Bed Leveling requires one of these: PROBE_MANUALLY, SENSORLESS_PROBING, BLTOUCH, FIX_MOUNTED_PROBE, NOZZLE_AS_PROBE, TOUCH_MI_PROBE, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or a Z Servo." + #endif + + #if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST) + #error "Z_MIN_PROBE_REPEATABILITY_TEST requires a probe: FIX_MOUNTED_PROBE, NOZZLE_AS_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or Z Servo." + #endif + +#endif + +#if ENABLED(LEVEL_BED_CORNERS) + #ifndef LEVEL_CORNERS_INSET_LFRB + #error "LEVEL_BED_CORNERS requires LEVEL_CORNERS_INSET_LFRB values." + #elif ENABLED(LEVEL_CORNERS_USE_PROBE) + #if !HAS_BED_PROBE + #error "LEVEL_CORNERS_USE_PROBE requires a real probe." + #elif ENABLED(SENSORLESS_PROBING) + #error "LEVEL_CORNERS_USE_PROBE is incompatible with SENSORLESS_PROBING." + #endif + #endif +#endif + +/** + * Allow only one bed leveling option to be defined + */ +#if MANY(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL, MESH_BED_LEVELING) + #error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL." +#endif + +/** + * Bed Leveling Requirements + */ + +#if ENABLED(AUTO_BED_LEVELING_UBL) + + /** + * Unified Bed Leveling + */ + + #if IS_SCARA + #error "AUTO_BED_LEVELING_UBL does not yet support SCARA printers." + #elif DISABLED(EEPROM_SETTINGS) + #error "AUTO_BED_LEVELING_UBL requires EEPROM_SETTINGS." + #elif !WITHIN(GRID_MAX_POINTS_X, 3, 15) || !WITHIN(GRID_MAX_POINTS_Y, 3, 15) + #error "GRID_MAX_POINTS_[XY] must be a whole number between 3 and 15." + #endif + +#elif HAS_ABL_NOT_UBL + + /** + * Auto Bed Leveling + */ + + /** + * Delta and SCARA have limited bed leveling options + */ + #if IS_SCARA && DISABLED(AUTO_BED_LEVELING_BILINEAR) + #error "SCARA machines can only use the AUTO_BED_LEVELING_BILINEAR leveling option." + #endif + +#elif ENABLED(MESH_BED_LEVELING) + + // Mesh Bed Leveling + #if ENABLED(DELTA) + #error "MESH_BED_LEVELING is not compatible with DELTA printers." + #elif GRID_MAX_POINTS_X > 9 || GRID_MAX_POINTS_Y > 9 + #error "GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y must be less than 10 for MBL." + #endif + +#endif + +#if ALL(HAS_LEVELING, RESTORE_LEVELING_AFTER_G28, ENABLE_LEVELING_AFTER_G28) + #error "Only enable RESTORE_LEVELING_AFTER_G28 or ENABLE_LEVELING_AFTER_G28, but not both." +#endif + +#if HAS_MESH && HAS_CLASSIC_JERK + static_assert(DEFAULT_ZJERK > 0.1, "Low DEFAULT_ZJERK values are incompatible with mesh-based leveling."); +#endif + +#if ENABLED(G26_MESH_VALIDATION) + #if !EXTRUDERS + #error "G26_MESH_VALIDATION requires at least one extruder." + #elif !HAS_MESH + #error "G26_MESH_VALIDATION requires MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_UBL." + #endif +#endif + +#if ENABLED(MESH_EDIT_GFX_OVERLAY) && !BOTH(AUTO_BED_LEVELING_UBL, HAS_MARLINUI_U8GLIB) + #error "MESH_EDIT_GFX_OVERLAY requires AUTO_BED_LEVELING_UBL and a Graphical LCD." +#endif + +#if ENABLED(G29_RETRY_AND_RECOVER) + #if ENABLED(AUTO_BED_LEVELING_UBL) + #error "G29_RETRY_AND_RECOVER is not compatible with UBL." + #elif ENABLED(MESH_BED_LEVELING) + #error "G29_RETRY_AND_RECOVER is not compatible with MESH_BED_LEVELING." + #endif +#endif + +/** + * LCD_BED_LEVELING requirements + */ +#if ENABLED(LCD_BED_LEVELING) + #if !HAS_LCD_MENU + #error "LCD_BED_LEVELING requires a programmable LCD controller." + #elif !(ENABLED(MESH_BED_LEVELING) || HAS_ABL_NOT_UBL) + #error "LCD_BED_LEVELING requires MESH_BED_LEVELING or AUTO_BED_LEVELING." + #endif +#endif + +#if BOTH(PREHEAT_BEFORE_PROBING, PREHEAT_BEFORE_LEVELING) + #error "Disable PREHEAT_BEFORE_LEVELING when using PREHEAT_BEFORE_PROBING." +#endif + +/** + * Homing + */ +constexpr float hbm[] = HOMING_BUMP_MM; +static_assert(COUNT(hbm) == XYZ, "HOMING_BUMP_MM requires X, Y, and Z elements."); +static_assert(hbm[X_AXIS] >= 0, "HOMING_BUMP_MM.X must be greater than or equal to 0."); +static_assert(hbm[Y_AXIS] >= 0, "HOMING_BUMP_MM.Y must be greater than or equal to 0."); +static_assert(hbm[Z_AXIS] >= 0, "HOMING_BUMP_MM.Z must be greater than or equal to 0."); + +#if ENABLED(CODEPENDENT_XY_HOMING) + #if ENABLED(QUICK_HOME) + #error "QUICK_HOME is incompatible with CODEPENDENT_XY_HOMING." + #elif IS_KINEMATIC + #error "CODEPENDENT_XY_HOMING requires a Cartesian setup." + #endif +#endif + +/** + * Make sure Z_SAFE_HOMING point is reachable + */ +#if ENABLED(Z_SAFE_HOMING) + static_assert(WITHIN(Z_SAFE_HOMING_X_POINT, X_MIN_POS, X_MAX_POS), "Z_SAFE_HOMING_X_POINT can't be reached by the nozzle."); + static_assert(WITHIN(Z_SAFE_HOMING_Y_POINT, Y_MIN_POS, Y_MAX_POS), "Z_SAFE_HOMING_Y_POINT can't be reached by the nozzle."); +#endif + +/** + * Make sure DISABLE_[XYZ] compatible with selected homing options + */ +#if ANY(DISABLE_X, DISABLE_Y, DISABLE_Z) + #if EITHER(HOME_AFTER_DEACTIVATE, Z_SAFE_HOMING) + #error "DISABLE_[XYZ] is not compatible with HOME_AFTER_DEACTIVATE or Z_SAFE_HOMING." + #endif +#endif + +/** + * Filament Width Sensor + */ +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #if !HAS_FILAMENT_WIDTH_SENSOR + #error "FILAMENT_WIDTH_SENSOR requires a FILWIDTH_PIN to be defined." + #elif ENABLED(NO_VOLUMETRICS) + #error "FILAMENT_WIDTH_SENSOR requires NO_VOLUMETRICS to be disabled." + #endif +#endif + +/** + * System Power Sensor + */ +#if ENABLED(POWER_MONITOR_CURRENT) && !PIN_EXISTS(POWER_MONITOR_CURRENT) + #error "POWER_MONITOR_CURRENT requires a valid POWER_MONITOR_CURRENT_PIN." +#elif ENABLED(POWER_MONITOR_VOLTAGE) && !PIN_EXISTS(POWER_MONITOR_VOLTAGE) + #error "POWER_MONITOR_VOLTAGE requires POWER_MONITOR_VOLTAGE_PIN to be defined." +#elif BOTH(POWER_MONITOR_CURRENT, POWER_MONITOR_VOLTAGE) && POWER_MONITOR_CURRENT_PIN == POWER_MONITOR_VOLTAGE_PIN + #error "POWER_MONITOR_CURRENT_PIN and POWER_MONITOR_VOLTAGE_PIN must be different." +#endif + +/** + * Volumetric Extruder Limit + */ +#if ENABLED(VOLUMETRIC_EXTRUDER_LIMIT) + #if ENABLED(NO_VOLUMETRICS) + #error "VOLUMETRIC_EXTRUDER_LIMIT requires NO_VOLUMETRICS to be disabled." + #elif MIN_STEPS_PER_SEGMENT > 1 + #error "VOLUMETRIC_EXTRUDER_LIMIT is not compatible with MIN_STEPS_PER_SEGMENT greater than 1." + #endif +#endif + +/** + * ULTIPANEL encoder + */ +#if IS_ULTIPANEL && NONE(IS_NEWPANEL, SR_LCD_2W_NL) && !PIN_EXISTS(SHIFT_CLK) + #error "ULTIPANEL controllers require some kind of encoder." +#endif + +#if ENCODER_PULSES_PER_STEP < 0 + #error "ENCODER_PULSES_PER_STEP should not be negative, use REVERSE_MENU_DIRECTION instead." +#endif + +/** + * SAV_3DGLCD display options + */ +#if ENABLED(SAV_3DGLCD) + #if NONE(U8GLIB_SSD1306, U8GLIB_SH1106) + #error "Enable a SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106." + #elif BOTH(U8GLIB_SSD1306, U8GLIB_SH1106) + #error "Only enable one SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106." + #endif +#endif + +/** + * Allen Key + * Deploying the Allen Key probe uses big moves in z direction. Too dangerous for an unhomed z-axis. + */ +#if BOTH(Z_PROBE_ALLEN_KEY, Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) && (Z_HOME_DIR < 0) + #error "You can't home to a Z min endstop with a Z_PROBE_ALLEN_KEY." +#endif + +/** + * Dual X Carriage requirements + */ +#if ENABLED(DUAL_X_CARRIAGE) + #if EXTRUDERS < 2 + #error "DUAL_X_CARRIAGE requires 2 (or more) extruders." + #elif ANY(CORE_IS_XY, CORE_IS_XZ, MARKFORGED_XY) + #error "DUAL_X_CARRIAGE cannot be used with COREXY, COREYX, COREXZ, COREZX, or MARKFORGED_XY." + #elif !GOOD_AXIS_PINS(X2) + #error "DUAL_X_CARRIAGE requires X2 stepper pins to be defined." + #elif !HAS_X_MAX + #error "DUAL_X_CARRIAGE requires USE_XMAX_PLUG and an X Max Endstop." + #elif !defined(X2_HOME_POS) || !defined(X2_MIN_POS) || !defined(X2_MAX_POS) + #error "DUAL_X_CARRIAGE requires X2_HOME_POS, X2_MIN_POS, and X2_MAX_POS." + #elif X_HOME_DIR != -1 || X2_HOME_DIR != 1 + #error "DUAL_X_CARRIAGE requires X_HOME_DIR -1 and X2_HOME_DIR 1." + #endif +#endif + +#undef GOOD_AXIS_PINS + +/** + * Make sure auto fan pins don't conflict with the fan pin + */ +#if HAS_AUTO_FAN + #if HAS_FAN0 + #if E0_AUTO_FAN_PIN == FAN_PIN + #error "You cannot set E0_AUTO_FAN_PIN equal to FAN_PIN." + #elif E1_AUTO_FAN_PIN == FAN_PIN + #error "You cannot set E1_AUTO_FAN_PIN equal to FAN_PIN." + #elif E2_AUTO_FAN_PIN == FAN_PIN + #error "You cannot set E2_AUTO_FAN_PIN equal to FAN_PIN." + #elif E3_AUTO_FAN_PIN == FAN_PIN + #error "You cannot set E3_AUTO_FAN_PIN equal to FAN_PIN." + #endif + #endif +#endif + +#if HAS_FAN0 && CONTROLLER_FAN_PIN == FAN_PIN + #error "You cannot set CONTROLLER_FAN_PIN equal to FAN_PIN." +#endif + +#if ENABLED(USE_CONTROLLER_FAN) + #if !HAS_CONTROLLER_FAN + #error "USE_CONTROLLER_FAN requires a CONTROLLER_FAN_PIN. Define in Configuration_adv.h." + #elif E0_AUTO_FAN_PIN == CONTROLLER_FAN_PIN + #error "You cannot set E0_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN." + #elif E1_AUTO_FAN_PIN == CONTROLLER_FAN_PIN + #error "You cannot set E1_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN." + #elif E2_AUTO_FAN_PIN == CONTROLLER_FAN_PIN + #error "You cannot set E2_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN." + #elif E3_AUTO_FAN_PIN == CONTROLLER_FAN_PIN + #error "You cannot set E3_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN." + #endif +#endif + +/** + * Case Light requirements + */ +#if ENABLED(CASE_LIGHT_ENABLE) + #if !PIN_EXISTS(CASE_LIGHT) + #error "CASE_LIGHT_ENABLE requires CASE_LIGHT_PIN to be defined." + #elif CASE_LIGHT_PIN == FAN_PIN + #error "CASE_LIGHT_PIN conflicts with FAN_PIN. Resolve before continuing." + #endif +#endif + +/** + * Required custom thermistor settings + */ +#if HEATER_0_USER_THERMISTOR && !(defined(HOTEND0_PULLUP_RESISTOR_OHMS) && defined(HOTEND0_RESISTANCE_25C_OHMS) && defined(HOTEND0_BETA)) + #error "TEMP_SENSOR_0 1000 requires HOTEND0_PULLUP_RESISTOR_OHMS, HOTEND0_RESISTANCE_25C_OHMS and HOTEND0_BETA in Configuration_adv.h." +#elif HEATER_1_USER_THERMISTOR && !(defined(HOTEND1_PULLUP_RESISTOR_OHMS) && defined(HOTEND1_RESISTANCE_25C_OHMS) && defined(HOTEND1_BETA)) + #error "TEMP_SENSOR_1 1000 requires HOTEND1_PULLUP_RESISTOR_OHMS, HOTEND1_RESISTANCE_25C_OHMS and HOTEND1_BETA in Configuration_adv.h." +#elif HEATER_2_USER_THERMISTOR && !(defined(HOTEND2_PULLUP_RESISTOR_OHMS) && defined(HOTEND2_RESISTANCE_25C_OHMS) && defined(HOTEND2_BETA)) + #error "TEMP_SENSOR_2 1000 requires HOTEND2_PULLUP_RESISTOR_OHMS, HOTEND2_RESISTANCE_25C_OHMS and HOTEND2_BETA in Configuration_adv.h." +#elif HEATER_3_USER_THERMISTOR && !(defined(HOTEND3_PULLUP_RESISTOR_OHMS) && defined(HOTEND3_RESISTANCE_25C_OHMS) && defined(HOTEND3_BETA)) + #error "TEMP_SENSOR_3 1000 requires HOTEND3_PULLUP_RESISTOR_OHMS, HOTEND3_RESISTANCE_25C_OHMS and HOTEND3_BETA in Configuration_adv.h." +#elif HEATER_4_USER_THERMISTOR && !(defined(HOTEND4_PULLUP_RESISTOR_OHMS) && defined(HOTEND4_RESISTANCE_25C_OHMS) && defined(HOTEND4_BETA)) + #error "TEMP_SENSOR_4 1000 requires HOTEND4_PULLUP_RESISTOR_OHMS, HOTEND4_RESISTANCE_25C_OHMS and HOTEND4_BETA in Configuration_adv.h." +#elif HEATER_5_USER_THERMISTOR && !(defined(HOTEND5_PULLUP_RESISTOR_OHMS) && defined(HOTEND5_RESISTANCE_25C_OHMS) && defined(HOTEND5_BETA)) + #error "TEMP_SENSOR_5 1000 requires HOTEND5_PULLUP_RESISTOR_OHMS, HOTEND5_RESISTANCE_25C_OHMS and HOTEND5_BETA in Configuration_adv.h." +#elif HEATER_6_USER_THERMISTOR && !(defined(HOTEND6_PULLUP_RESISTOR_OHMS) && defined(HOTEND6_RESISTANCE_25C_OHMS) && defined(HOTEND6_BETA)) + #error "TEMP_SENSOR_6 1000 requires HOTEND6_PULLUP_RESISTOR_OHMS, HOTEND6_RESISTANCE_25C_OHMS and HOTEND6_BETA in Configuration_adv.h." +#elif HEATER_7_USER_THERMISTOR && !(defined(HOTEND7_PULLUP_RESISTOR_OHMS) && defined(HOTEND7_RESISTANCE_25C_OHMS) && defined(HOTEND7_BETA)) + #error "TEMP_SENSOR_7 1000 requires HOTEND7_PULLUP_RESISTOR_OHMS, HOTEND7_RESISTANCE_25C_OHMS and HOTEND7_BETA in Configuration_adv.h." +#elif HEATER_BED_USER_THERMISTOR && !(defined(BED_PULLUP_RESISTOR_OHMS) && defined(BED_RESISTANCE_25C_OHMS) && defined(BED_BETA)) + #error "TEMP_SENSOR_BED 1000 requires BED_PULLUP_RESISTOR_OHMS, BED_RESISTANCE_25C_OHMS and BED_BETA in Configuration_adv.h." +#elif HEATER_CHAMBER_USER_THERMISTOR && !(defined(CHAMBER_PULLUP_RESISTOR_OHMS) && defined(CHAMBER_RESISTANCE_25C_OHMS) && defined(CHAMBER_BETA)) + #error "TEMP_SENSOR_CHAMBER 1000 requires CHAMBER_PULLUP_RESISTOR_OHMS, CHAMBER_RESISTANCE_25C_OHMS and CHAMBER_BETA in Configuration_adv.h." +#endif + +/** + * Pins and Sensor IDs must be set for each heater + */ +#if HEATER_0_USES_MAX6675 && !PIN_EXISTS(MAX6675_SS) + #error "MAX6675_SS_PIN (required for TEMP_SENSOR_0) not defined for this board." +#elif HAS_HOTEND && !HAS_TEMP_HOTEND && !HEATER_0_DUMMY_THERMISTOR + #error "TEMP_0_PIN (required for TEMP_SENSOR_0) not defined for this board." +#elif EITHER(HAS_MULTI_HOTEND, HEATERS_PARALLEL) && !HAS_HEATER_1 + #error "HEATER_1_PIN is not defined. TEMP_SENSOR_1 might not be set, or the board (not EEB / EEF?) doesn't define a pin." +#endif + +#if HAS_MULTI_HOTEND + #if HEATER_1_USES_MAX6675 && !PIN_EXISTS(MAX6675_SS2) + #error "MAX6675_SS2_PIN (required for TEMP_SENSOR_1) not defined for this board." + #elif TEMP_SENSOR_1 == 0 + #error "TEMP_SENSOR_1 is required with 2 or more HOTENDS." + #elif !ANY_PIN(TEMP_1, MAX6675_SS2) && !HEATER_1_DUMMY_THERMISTOR + #error "TEMP_1_PIN not defined for this board." + #elif ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) + #error "HOTENDS must be 1 with TEMP_SENSOR_1_AS_REDUNDANT." + #endif + #if HOTENDS > 2 + #if TEMP_SENSOR_2 == 0 + #error "TEMP_SENSOR_2 is required with 3 or more HOTENDS." + #elif !HAS_HEATER_2 + #error "HEATER_2_PIN not defined for this board." + #elif !PIN_EXISTS(TEMP_2) && !HEATER_2_DUMMY_THERMISTOR + #error "TEMP_2_PIN not defined for this board." + #endif + #if HOTENDS > 3 + #if TEMP_SENSOR_3 == 0 + #error "TEMP_SENSOR_3 is required with 4 or more HOTENDS." + #elif !HAS_HEATER_3 + #error "HEATER_3_PIN not defined for this board." + #elif !PIN_EXISTS(TEMP_3) && !HEATER_3_DUMMY_THERMISTOR + #error "TEMP_3_PIN not defined for this board." + #endif + #if HOTENDS > 4 + #if TEMP_SENSOR_4 == 0 + #error "TEMP_SENSOR_4 is required with 5 or more HOTENDS." + #elif !HAS_HEATER_4 + #error "HEATER_4_PIN not defined for this board." + #elif !PIN_EXISTS(TEMP_4) && !HEATER_4_DUMMY_THERMISTOR + #error "TEMP_4_PIN not defined for this board." + #endif + #if HOTENDS > 5 + #if TEMP_SENSOR_5 == 0 + #error "TEMP_SENSOR_5 is required with 6 HOTENDS." + #elif !HAS_HEATER_5 + #error "HEATER_5_PIN not defined for this board." + #elif !PIN_EXISTS(TEMP_5) && !HEATER_5_DUMMY_THERMISTOR + #error "TEMP_5_PIN not defined for this board." + #endif + #if HOTENDS > 6 + #if TEMP_SENSOR_6 == 0 + #error "TEMP_SENSOR_6 is required with 6 HOTENDS." + #elif !HAS_HEATER_6 + #error "HEATER_6_PIN not defined for this board." + #elif !PIN_EXISTS(TEMP_6) && !HEATER_6_DUMMY_THERMISTOR + #error "TEMP_6_PIN not defined for this board." + #endif + #if HOTENDS > 7 + #if TEMP_SENSOR_7 == 0 + #error "TEMP_SENSOR_7 is required with 7 HOTENDS." + #elif !HAS_HEATER_7 + #error "HEATER_7_PIN not defined for this board." + #elif !PIN_EXISTS(TEMP_7) && !HEATER_7_DUMMY_THERMISTOR + #error "TEMP_7_PIN not defined for this board." + #endif + #elif TEMP_SENSOR_7 != 0 + #error "TEMP_SENSOR_7 shouldn't be set with only 7 HOTENDS." + #endif + #elif TEMP_SENSOR_6 != 0 + #error "TEMP_SENSOR_6 shouldn't be set with only 6 HOTENDS." + #elif TEMP_SENSOR_7 != 0 + #error "TEMP_SENSOR_7 shouldn't be set with only 6 HOTENDS." + #endif + #elif TEMP_SENSOR_5 != 0 + #error "TEMP_SENSOR_5 shouldn't be set with only 5 HOTENDS." + #elif TEMP_SENSOR_6 != 0 + #error "TEMP_SENSOR_6 shouldn't be set with only 5 HOTENDS." + #elif TEMP_SENSOR_7 != 0 + #error "TEMP_SENSOR_7 shouldn't be set with only 5 HOTENDS." + #endif + #elif TEMP_SENSOR_4 != 0 + #error "TEMP_SENSOR_4 shouldn't be set with only 4 HOTENDS." + #elif TEMP_SENSOR_5 != 0 + #error "TEMP_SENSOR_5 shouldn't be set with only 4 HOTENDS." + #elif TEMP_SENSOR_6 != 0 + #error "TEMP_SENSOR_6 shouldn't be set with only 4 HOTENDS." + #elif TEMP_SENSOR_7 != 0 + #error "TEMP_SENSOR_7 shouldn't be set with only 4 HOTENDS." + #endif + #elif TEMP_SENSOR_3 != 0 + #error "TEMP_SENSOR_3 shouldn't be set with only 3 HOTENDS." + #elif TEMP_SENSOR_4 != 0 + #error "TEMP_SENSOR_4 shouldn't be set with only 3 HOTENDS." + #elif TEMP_SENSOR_5 != 0 + #error "TEMP_SENSOR_5 shouldn't be set with only 3 HOTENDS." + #elif TEMP_SENSOR_6 != 0 + #error "TEMP_SENSOR_6 shouldn't be set with only 3 HOTENDS." + #elif TEMP_SENSOR_7 != 0 + #error "TEMP_SENSOR_7 shouldn't be set with only 3 HOTENDS." + #endif + #elif TEMP_SENSOR_2 != 0 + #error "TEMP_SENSOR_2 shouldn't be set with only 2 HOTENDS." + #elif TEMP_SENSOR_3 != 0 + #error "TEMP_SENSOR_3 shouldn't be set with only 2 HOTENDS." + #elif TEMP_SENSOR_4 != 0 + #error "TEMP_SENSOR_4 shouldn't be set with only 2 HOTENDS." + #elif TEMP_SENSOR_5 != 0 + #error "TEMP_SENSOR_5 shouldn't be set with only 2 HOTENDS." + #elif TEMP_SENSOR_6 != 0 + #error "TEMP_SENSOR_6 shouldn't be set with only 2 HOTENDS." + #elif TEMP_SENSOR_7 != 0 + #error "TEMP_SENSOR_7 shouldn't be set with only 2 HOTENDS." + #endif +#elif TEMP_SENSOR_1 != 0 && DISABLED(TEMP_SENSOR_1_AS_REDUNDANT) + #error "TEMP_SENSOR_1 shouldn't be set with only 1 HOTEND." +#elif TEMP_SENSOR_2 != 0 + #error "TEMP_SENSOR_2 shouldn't be set with only 1 HOTEND." +#elif TEMP_SENSOR_3 != 0 + #error "TEMP_SENSOR_3 shouldn't be set with only 1 HOTEND." +#elif TEMP_SENSOR_4 != 0 + #error "TEMP_SENSOR_4 shouldn't be set with only 1 HOTEND." +#elif TEMP_SENSOR_5 != 0 + #error "TEMP_SENSOR_5 shouldn't be set with only 1 HOTEND." +#elif TEMP_SENSOR_6 != 0 + #error "TEMP_SENSOR_6 shouldn't be set with only 1 HOTEND." +#elif TEMP_SENSOR_7 != 0 + #error "TEMP_SENSOR_7 shouldn't be set with only 1 HOTEND." +#endif + +#if TEMP_SENSOR_CHAMBER && !PIN_EXISTS(TEMP_CHAMBER) + #error "TEMP_SENSOR_CHAMBER requires TEMP_CHAMBER_PIN." +#endif + +#if ENABLED(CHAMBER_FAN) && !(defined(CHAMBER_FAN_MODE) && WITHIN(CHAMBER_FAN_MODE, 0, 2)) + #error "CHAMBER_FAN_MODE must be between 0 and 2." +#endif + +#if ENABLED(CHAMBER_VENT) + #ifndef CHAMBER_VENT_SERVO_NR + #error "CHAMBER_VENT_SERVO_NR is required for CHAMBER SERVO." + #elif !NUM_SERVOS + #error "NUM_SERVOS is required for a Heated Chamber vent servo (CHAMBER_VENT_SERVO_NR)." + #elif CHAMBER_VENT_SERVO_NR >= NUM_SERVOS + #error "CHAMBER_VENT_SERVO_NR must be smaller than NUM_SERVOS." + #elif HAS_Z_SERVO_PROBE && CHAMBER_VENT_SERVO_NR == Z_PROBE_SERVO_NR + #error "CHAMBER SERVO is already used by BLTOUCH." + #elif CHAMBER_VENT_SERVO_NR == 0 && !PIN_EXISTS(SERVO0) + #error "SERVO0_PIN must be defined for your Heated Chamber vent servo." + #elif CHAMBER_VENT_SERVO_NR == 1 && !PIN_EXISTS(SERVO1) + #error "SERVO1_PIN must be defined for your Heated Chamber vent servo." + #elif CHAMBER_VENT_SERVO_NR == 2 && !PIN_EXISTS(SERVO2) + #error "SERVO2_PIN must be defined for your Heated Chamber vent servo." + #elif CHAMBER_VENT_SERVO_NR == 3 && !PIN_EXISTS(SERVO3) + #error "SERVO3_PIN must be defined for your Heated Chamber vent servo." + #endif +#endif + +#if TEMP_SENSOR_PROBE + #if !PIN_EXISTS(TEMP_PROBE) + #error "TEMP_SENSOR_PROBE requires TEMP_PROBE_PIN." + #elif !HAS_TEMP_ADC_PROBE + #error "TEMP_PROBE_PIN must be an ADC pin." + #elif DISABLED(FIX_MOUNTED_PROBE) + #error "TEMP_SENSOR_PROBE shouldn't be set without FIX_MOUNTED_PROBE." + #endif +#endif + +#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) && TEMP_SENSOR_1 == 0 + #error "TEMP_SENSOR_1 is required with TEMP_SENSOR_1_AS_REDUNDANT." +#endif + +#if MAX6675_0_IS_MAX31865 && !(defined(MAX31865_SENSOR_OHMS_0) && defined(MAX31865_CALIBRATION_OHMS_0)) + #error "MAX31865_SENSOR_OHMS_0 and MAX31865_CALIBRATION_OHMS_0 must be set if TEMP_SENSOR_0 is MAX31865." +#elif MAX6675_1_IS_MAX31865 && !(defined(MAX31865_SENSOR_OHMS_1) && defined(MAX31865_CALIBRATION_OHMS_1)) + #error "MAX31865_SENSOR_OHMS_1 and MAX31865_CALIBRATION_OHMS_1 must be set if TEMP_SENSOR_1 is MAX31865." +#endif + +/** + * Test Heater, Temp Sensor, and Extruder Pins + */ +#if !HAS_HEATER_0 && EXTRUDERS + #error "HEATER_0_PIN not defined for this board." +#elif !ANY_PIN(TEMP_0, MAX6675_SS) + #error "TEMP_0_PIN not defined for this board." +#elif ((defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)) && !PINS_EXIST(E0_STEP, E0_DIR)) + #error "E0_STEP_PIN or E0_DIR_PIN not defined for this board." +#elif ( !(defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)) && (!PINS_EXIST(E0_STEP, E0_DIR) || !HAS_E0_ENABLE)) + #error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board." +#elif EXTRUDERS && TEMP_SENSOR_0 == 0 + #error "TEMP_SENSOR_0 is required if there are any extruders." +#endif + +/** + * Temperature status LEDs + */ +#if ENABLED(TEMP_STAT_LEDS) && !ANY_PIN(STAT_LED_RED, STAT_LED_BLUE) + #error "TEMP_STAT_LEDS requires STAT_LED_RED_PIN or STAT_LED_BLUE_PIN, preferably both." +#endif + +/** + * LED Control Menu + */ +#if ENABLED(LED_CONTROL_MENU) && !HAS_COLOR_LEDS + #error "LED_CONTROL_MENU requires BLINKM, RGB_LED, RGBW_LED, PCA9533, PCA9632, or NEOPIXEL_LED." +#endif + +/** + * LED Backlight Timeout + */ +#if defined(LED_BACKLIGHT_TIMEOUT) && !(ENABLED(PSU_CONTROL) && ANY(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1, FYSETC_242_OLED_12864)) + #error "LED_BACKLIGHT_TIMEOUT requires a FYSETC Mini Panel and a Power Switch." +#endif + +/** + * Basic multi hotend duplication mode + */ +#if ENABLED(MULTI_NOZZLE_DUPLICATION) + #if ENABLED(SINGLENOZZLE) + #error "MULTI_NOZZLE_DUPLICATION is incompatible with SINGLENOZZLE." + #elif ENABLED(DUAL_X_CARRIAGE) + #error "MULTI_NOZZLE_DUPLICATION is incompatible with DUAL_X_CARRIAGE." + #elif ENABLED(MIXING_EXTRUDER) + #error "MULTI_NOZZLE_DUPLICATION is incompatible with MIXING_EXTRUDER." + #elif ENABLED(SWITCHING_EXTRUDER) + #error "MULTI_NOZZLE_DUPLICATION is incompatible with SWITCHING_EXTRUDER." + #elif HOTENDS < 2 + #error "MULTI_NOZZLE_DUPLICATION requires 2 or more hotends." + #endif +#endif + +/** + * Test Extruder Stepper Pins + */ +#if E_STEPPERS + #if !(PINS_EXIST(E0_STEP, E0_DIR) && HAS_E0_ENABLE) + #error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board." + #endif + #if E_STEPPERS > 1 + #if !(PINS_EXIST(E1_STEP, E1_DIR) && HAS_E1_ENABLE) + #error "E1_STEP_PIN, E1_DIR_PIN, or E1_ENABLE_PIN not defined for this board." + #endif + #if E_STEPPERS > 2 + #if !(PINS_EXIST(E2_STEP, E2_DIR) && HAS_E2_ENABLE) + #error "E2_STEP_PIN, E2_DIR_PIN, or E2_ENABLE_PIN not defined for this board." + #endif + #if E_STEPPERS > 3 + #if !(PINS_EXIST(E3_STEP, E3_DIR) && HAS_E3_ENABLE) + #error "E3_STEP_PIN, E3_DIR_PIN, or E3_ENABLE_PIN not defined for this board." + #endif + #if E_STEPPERS > 4 + #if !(PINS_EXIST(E4_STEP, E4_DIR) && HAS_E4_ENABLE) + #error "E4_STEP_PIN, E4_DIR_PIN, or E4_ENABLE_PIN not defined for this board." + #endif + #if E_STEPPERS > 5 + #if !(PINS_EXIST(E5_STEP, E5_DIR) && HAS_E5_ENABLE) + #error "E5_STEP_PIN, E5_DIR_PIN, or E5_ENABLE_PIN not defined for this board." + #endif + #if E_STEPPERS > 6 + #if !(PINS_EXIST(E6_STEP, E6_DIR) && HAS_E6_ENABLE) + #error "E6_STEP_PIN, E6_DIR_PIN, or E6_ENABLE_PIN not defined for this board." + #endif + #if E_STEPPERS > 7 + #if !(PINS_EXIST(E7_STEP, E7_DIR) && HAS_E7_ENABLE) + #error "E7_STEP_PIN, E7_DIR_PIN, or E7_ENABLE_PIN not defined for this board." + #endif + #endif // E_STEPPERS > 7 + #endif // E_STEPPERS > 6 + #endif // E_STEPPERS > 5 + #endif // E_STEPPERS > 4 + #endif // E_STEPPERS > 3 + #endif // E_STEPPERS > 2 + #endif // E_STEPPERS > 1 +#endif // E_STEPPERS + +/** + * Endstop Tests + */ + +#define _PLUG_UNUSED_TEST(A,P) (DISABLED(USE_##P##MIN_PLUG, USE_##P##MAX_PLUG) \ + && !(ENABLED(A##_DUAL_ENDSTOPS) && WITHIN(A##2_USE_ENDSTOP, _##P##MAX_, _##P##MIN_)) \ + && !(ENABLED(A##_MULTI_ENDSTOPS) && WITHIN(A##2_USE_ENDSTOP, _##P##MAX_, _##P##MIN_)) ) +#define _AXIS_PLUG_UNUSED_TEST(A) (_PLUG_UNUSED_TEST(A,X) && _PLUG_UNUSED_TEST(A,Y) && _PLUG_UNUSED_TEST(A,Z)) + +// At least 3 endstop plugs must be used +#if _AXIS_PLUG_UNUSED_TEST(X) + #error "You must enable USE_XMIN_PLUG or USE_XMAX_PLUG." +#endif +#if _AXIS_PLUG_UNUSED_TEST(Y) + #error "You must enable USE_YMIN_PLUG or USE_YMAX_PLUG." +#endif +#if _AXIS_PLUG_UNUSED_TEST(Z) + #error "You must enable USE_ZMIN_PLUG or USE_ZMAX_PLUG." +#endif + +// Delta and Cartesian use 3 homing endstops +#if NONE(IS_SCARA, SPI_ENDSTOPS) + #if X_HOME_DIR < 0 && DISABLED(USE_XMIN_PLUG) + #error "Enable USE_XMIN_PLUG when homing X to MIN." + #elif X_HOME_DIR > 0 && DISABLED(USE_XMAX_PLUG) + #error "Enable USE_XMAX_PLUG when homing X to MAX." + #elif Y_HOME_DIR < 0 && DISABLED(USE_YMIN_PLUG) + #error "Enable USE_YMIN_PLUG when homing Y to MIN." + #elif Y_HOME_DIR > 0 && DISABLED(USE_YMAX_PLUG) + #error "Enable USE_YMAX_PLUG when homing Y to MAX." + #endif +#endif + +// Z homing direction and plug usage flags +#if Z_HOME_DIR < 0 && NONE(USE_ZMIN_PLUG, HOMING_Z_WITH_PROBE) + #error "Enable USE_ZMIN_PLUG when homing Z to MIN." +#elif Z_HOME_DIR > 0 && ENABLED(USE_PROBE_FOR_Z_HOMING) + #error "Z_HOME_DIR must be -1 when homing Z with the probe." +#elif BOTH(HOMING_Z_WITH_PROBE, Z_MULTI_ENDSTOPS) + #error "Z_MULTI_ENDSTOPS is incompatible with USE_PROBE_FOR_Z_HOMING." +#elif Z_HOME_DIR > 0 && DISABLED(USE_ZMAX_PLUG) + #error "Enable USE_ZMAX_PLUG when homing Z to MAX." +#endif + +#if BOTH(HOME_Z_FIRST, USE_PROBE_FOR_Z_HOMING) + #error "HOME_Z_FIRST can't be used when homing Z with a probe." +#endif + +// Dual/multiple endstops requirements +#if ENABLED(X_DUAL_ENDSTOPS) + #if !X2_USE_ENDSTOP + #error "You must set X2_USE_ENDSTOP with X_DUAL_ENDSTOPS." + #elif X2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG) + #error "USE_XMIN_PLUG is required when X2_USE_ENDSTOP is _XMIN_." + #elif X2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG) + #error "USE_XMAX_PLUG is required when X2_USE_ENDSTOP is _XMAX_." + #elif X2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG) + #error "USE_YMIN_PLUG is required when X2_USE_ENDSTOP is _YMIN_." + #elif X2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG) + #error "USE_YMAX_PLUG is required when X2_USE_ENDSTOP is _YMAX_." + #elif X2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG) + #error "USE_ZMIN_PLUG is required when X2_USE_ENDSTOP is _ZMIN_." + #elif X2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG) + #error "USE_ZMAX_PLUG is required when X2_USE_ENDSTOP is _ZMAX_." + #elif !HAS_X2_MIN && !HAS_X2_MAX + #error "X2_USE_ENDSTOP has been assigned to a nonexistent endstop!" + #elif ENABLED(DELTA) + #error "X_DUAL_ENDSTOPS is not compatible with DELTA." + #endif +#endif +#if ENABLED(Y_DUAL_ENDSTOPS) + #if !Y2_USE_ENDSTOP + #error "You must set Y2_USE_ENDSTOP with Y_DUAL_ENDSTOPS." + #elif Y2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG) + #error "USE_XMIN_PLUG is required when Y2_USE_ENDSTOP is _XMIN_." + #elif Y2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG) + #error "USE_XMAX_PLUG is required when Y2_USE_ENDSTOP is _XMAX_." + #elif Y2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG) + #error "USE_YMIN_PLUG is required when Y2_USE_ENDSTOP is _YMIN_." + #elif Y2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG) + #error "USE_YMAX_PLUG is required when Y2_USE_ENDSTOP is _YMAX_." + #elif Y2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG) + #error "USE_ZMIN_PLUG is required when Y2_USE_ENDSTOP is _ZMIN_." + #elif Y2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG) + #error "USE_ZMAX_PLUG is required when Y2_USE_ENDSTOP is _ZMAX_." + #elif !HAS_Y2_MIN && !HAS_Y2_MAX + #error "Y2_USE_ENDSTOP has been assigned to a nonexistent endstop!" + #elif ENABLED(DELTA) + #error "Y_DUAL_ENDSTOPS is not compatible with DELTA." + #endif +#endif + +#if ENABLED(Z_MULTI_ENDSTOPS) + #if !Z2_USE_ENDSTOP + #error "You must set Z2_USE_ENDSTOP with Z_MULTI_ENDSTOPS when NUM_Z_STEPPER_DRIVERS >= 2." + #elif Z2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG) + #error "USE_XMIN_PLUG is required when Z2_USE_ENDSTOP is _XMIN_." + #elif Z2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG) + #error "USE_XMAX_PLUG is required when Z2_USE_ENDSTOP is _XMAX_." + #elif Z2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG) + #error "USE_YMIN_PLUG is required when Z2_USE_ENDSTOP is _YMIN_." + #elif Z2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG) + #error "USE_YMAX_PLUG is required when Z2_USE_ENDSTOP is _YMAX_." + #elif Z2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG) + #error "USE_ZMIN_PLUG is required when Z2_USE_ENDSTOP is _ZMIN_." + #elif Z2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG) + #error "USE_ZMAX_PLUG is required when Z2_USE_ENDSTOP is _ZMAX_." + #elif !HAS_Z2_MIN && !HAS_Z2_MAX + #error "Z2_USE_ENDSTOP has been assigned to a nonexistent endstop!" + #elif ENABLED(DELTA) + #error "Z_MULTI_ENDSTOPS is not compatible with DELTA." + #endif + #if NUM_Z_STEPPER_DRIVERS >= 3 + #if !Z3_USE_ENDSTOP + #error "You must set Z3_USE_ENDSTOP with Z_MULTI_ENDSTOPS when NUM_Z_STEPPER_DRIVERS >= 3." + #elif Z3_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG) + #error "USE_XMIN_PLUG is required when Z3_USE_ENDSTOP is _XMIN_." + #elif Z3_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG) + #error "USE_XMAX_PLUG is required when Z3_USE_ENDSTOP is _XMAX_." + #elif Z3_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG) + #error "USE_YMIN_PLUG is required when Z3_USE_ENDSTOP is _YMIN_." + #elif Z3_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG) + #error "USE_YMAX_PLUG is required when Z3_USE_ENDSTOP is _YMAX_." + #elif Z3_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG) + #error "USE_ZMIN_PLUG is required when Z3_USE_ENDSTOP is _ZMIN_." + #elif Z3_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG) + #error "USE_ZMAX_PLUG is required when Z3_USE_ENDSTOP is _ZMAX_." + #elif !HAS_Z3_MIN && !HAS_Z3_MAX + #error "Z3_USE_ENDSTOP has been assigned to a nonexistent endstop!" + #endif + #endif + #if NUM_Z_STEPPER_DRIVERS >= 4 + #if !Z4_USE_ENDSTOP + #error "You must set Z4_USE_ENDSTOP with Z_MULTI_ENDSTOPS when NUM_Z_STEPPER_DRIVERS >= 4." + #elif Z4_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG) + #error "USE_XMIN_PLUG is required when Z4_USE_ENDSTOP is _XMIN_." + #elif Z4_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG) + #error "USE_XMAX_PLUG is required when Z4_USE_ENDSTOP is _XMAX_." + #elif Z4_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG) + #error "USE_YMIN_PLUG is required when Z4_USE_ENDSTOP is _YMIN_." + #elif Z4_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG) + #error "USE_YMAX_PLUG is required when Z4_USE_ENDSTOP is _YMAX_." + #elif Z4_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG) + #error "USE_ZMIN_PLUG is required when Z4_USE_ENDSTOP is _ZMIN_." + #elif Z4_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG) + #error "USE_ZMAX_PLUG is required when Z4_USE_ENDSTOP is _ZMAX_." + #elif !HAS_Z4_MIN && !HAS_Z4_MAX + #error "Z4_USE_ENDSTOP has been assigned to a nonexistent endstop!" + #endif + #endif +#endif + +#if defined(ENDSTOP_NOISE_THRESHOLD) && !WITHIN(ENDSTOP_NOISE_THRESHOLD, 2, 7) + #error "ENDSTOP_NOISE_THRESHOLD must be an integer from 2 to 7." +#endif + +/** + * emergency-command parser + */ +#if ENABLED(EMERGENCY_PARSER) && defined(__AVR__) && defined(USBCON) + #error "EMERGENCY_PARSER does not work on boards with AT90USB processors (USBCON)." +#endif + +/** + * I2C bus + */ +#if ENABLED(EXPERIMENTAL_I2CBUS) && I2C_SLAVE_ADDRESS > 0 + #if I2C_SLAVE_ADDRESS < 8 + #error "I2C_SLAVE_ADDRESS can't be less than 8. (Addresses 0 - 7 are reserved.)" + #elif I2C_SLAVE_ADDRESS > 127 + #error "I2C_SLAVE_ADDRESS can't be over 127. (Only 7 bits allowed.)" + #endif +#endif + +/** + * G35 Assisted Tramming + */ +#if ENABLED(ASSISTED_TRAMMING) && !HAS_BED_PROBE + #error "ASSISTED_TRAMMING requires a bed probe." +#endif + +/** + * G38 Probe Target + */ +#if ENABLED(G38_PROBE_TARGET) + #if !HAS_BED_PROBE + #error "G38_PROBE_TARGET requires a bed probe." + #elif !IS_CARTESIAN + #error "G38_PROBE_TARGET requires a Cartesian machine." + #endif +#endif + +/** + * RGB_LED Requirements + */ +#define _RGB_TEST (PINS_EXIST(RGB_LED_R, RGB_LED_G, RGB_LED_B)) +#if ENABLED(PRINTER_EVENT_LEDS) && !HAS_COLOR_LEDS + #error "PRINTER_EVENT_LEDS requires BLINKM, PCA9533, PCA9632, RGB_LED, RGBW_LED or NEOPIXEL_LED." +#elif ENABLED(RGB_LED) + #if !_RGB_TEST + #error "RGB_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, and RGB_LED_B_PIN." + #elif ENABLED(RGBW_LED) + #error "Please enable only one of RGB_LED and RGBW_LED." + #endif +#elif ENABLED(RGBW_LED) + #if !(_RGB_TEST && PIN_EXISTS(RGB_LED_W)) + #error "RGBW_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, RGB_LED_B_PIN, and RGB_LED_W_PIN." + #endif +#endif +#undef _RGB_TEST + +// NeoPixel requirements +#if ENABLED(NEOPIXEL_LED) + #if !PIN_EXISTS(NEOPIXEL) || NEOPIXEL_PIXELS == 0 + #error "NEOPIXEL_LED requires NEOPIXEL_PIN and NEOPIXEL_PIXELS." + #elif ENABLED(NEOPIXEL2_SEPARATE) && !(defined(NEOPIXEL2_TYPE) && PIN_EXISTS(NEOPIXEL2) && NEOPIXEL2_PIXELS > 0) + #error "NEOPIXEL2_SEPARATE requires NEOPIXEL2_TYPE, NEOPIXEL2_PIN and NEOPIXEL2_PIXELS." + #elif ENABLED(NEO2_COLOR_PRESETS) && DISABLED(NEOPIXEL2_SEPARATE) + #error "NEO2_COLOR_PRESETS requires NEOPIXEL2_SEPARATE to be enabled." + #endif +#endif + +#if DISABLED(NO_COMPILE_TIME_PWM) + #define _TEST_PWM(P) PWM_PIN(P) +#else + #define _TEST_PWM(P) 1 // pass +#endif + +/** + * Auto Fan check for PWM pins + */ +#if HAS_AUTO_FAN && EXTRUDER_AUTO_FAN_SPEED != 255 + #define AF_ERR_SUFF "_AUTO_FAN_PIN is not a PWM pin. Set EXTRUDER_AUTO_FAN_SPEED to 255." + #if HAS_AUTO_FAN_0 + static_assert(_TEST_PWM(E0_AUTO_FAN_PIN), "E0" AF_ERR_SUFF); + #elif HAS_AUTO_FAN_1 + static_assert(_TEST_PWM(E1_AUTO_FAN_PIN), "E1" AF_ERR_SUFF); + #elif HAS_AUTO_FAN_2 + static_assert(_TEST_PWM(E2_AUTO_FAN_PIN), "E2" AF_ERR_SUFF); + #elif HAS_AUTO_FAN_3 + static_assert(_TEST_PWM(E3_AUTO_FAN_PIN), "E3" AF_ERR_SUFF); + #elif HAS_AUTO_FAN_4 + static_assert(_TEST_PWM(E4_AUTO_FAN_PIN), "E4" AF_ERR_SUFF); + #elif HAS_AUTO_FAN_5 + static_assert(_TEST_PWM(E5_AUTO_FAN_PIN), "E5" AF_ERR_SUFF); + #elif HAS_AUTO_FAN_6 + static_assert(_TEST_PWM(E6_AUTO_FAN_PIN), "E6" AF_ERR_SUFF); + #elif HAS_AUTO_FAN_7 + static_assert(_TEST_PWM(E7_AUTO_FAN_PIN), "E7" AF_ERR_SUFF); + #endif +#endif + +/** + * Make sure only one EEPROM type is enabled + */ +#if ENABLED(EEPROM_SETTINGS) + #if 1 < 0 \ + + ENABLED(I2C_EEPROM) \ + + ENABLED(SPI_EEPROM) \ + + ENABLED(QSPI_EEPROM) \ + + ENABLED(SDCARD_EEPROM_EMULATION) \ + + ENABLED(FLASH_EEPROM_EMULATION) \ + + ENABLED(SRAM_EEPROM_EMULATION) \ + + ENABLED(IIC_BL24CXX_EEPROM) + #error "Please select only one method of EEPROM Persistent Storage." + #endif +#endif + +/** + * Make sure features that need to write to the SD card can + */ +#if ENABLED(SDCARD_READONLY) && ANY(POWER_LOSS_RECOVERY, BINARY_FILE_TRANSFER, SDCARD_EEPROM_EMULATION) + #undef SDCARD_READONLY + #if ENABLED(POWER_LOSS_RECOVERY) + #warning "Either disable SDCARD_READONLY or disable POWER_LOSS_RECOVERY." + #elif ENABLED(BINARY_FILE_TRANSFER) + #warning "Either disable SDCARD_READONLY or disable BINARY_FILE_TRANSFER." + #elif ENABLED(SDCARD_EEPROM_EMULATION) + #warning "Either disable SDCARD_READONLY or disable SDCARD_EEPROM_EMULATION." + #endif +#endif + +#if ENABLED(SD_IGNORE_AT_STARTUP) + #if ENABLED(POWER_LOSS_RECOVERY) + #error "SD_IGNORE_AT_STARTUP is incompatible with POWER_LOSS_RECOVERY." + #elif ENABLED(SDCARD_EEPROM_EMULATION) + #error "SD_IGNORE_AT_STARTUP is incompatible with SDCARD_EEPROM_EMULATION." + #endif +#endif + +/** + * Make sure only one display is enabled + */ +#if 1 < 0 \ + + ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) \ + + ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) \ + + ENABLED(ULTIPANEL) \ + + ENABLED(ULTRA_LCD) \ + + (ENABLED(U8GLIB_SSD1306) && DISABLED(IS_U8GLIB_SSD1306)) \ + + (ENABLED(MINIPANEL) && NONE(MKS_MINI_12864, ENDER2_STOCKDISPLAY)) \ + + (ENABLED(MKS_MINI_12864) && DISABLED(MKS_LCD12864)) \ + + (ENABLED(EXTENSIBLE_UI) && DISABLED(IS_EXTUI)) \ + + (DISABLED(IS_LEGACY_TFT) && ENABLED(TFT_GENERIC)) \ + + (ENABLED(IS_LEGACY_TFT) && COUNT_ENABLED(TFT_320x240, TFT_320x240_SPI, TFT_480x320, TFT_480x320_SPI)) \ + + COUNT_ENABLED(ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON, ANYCUBIC_TFT35) \ + + COUNT_ENABLED(DGUS_LCD_UI_ORIGIN, DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_HIPRECY) \ + + COUNT_ENABLED(ENDER2_STOCKDISPLAY, CR10_STOCKDISPLAY, DWIN_CREALITY_LCD) \ + + COUNT_ENABLED(FYSETC_MINI_12864_X_X, FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1, FYSETC_GENERIC_12864_1_1) \ + + COUNT_ENABLED(LCD_SAINSMART_I2C_1602, LCD_SAINSMART_I2C_2004) \ + + COUNT_ENABLED(MKS_12864OLED, MKS_12864OLED_SSD1306) \ + + COUNT_ENABLED(MKS_TS35_V2_0, MKS_ROBIN_TFT24, MKS_ROBIN_TFT28, MKS_ROBIN_TFT32, MKS_ROBIN_TFT35, MKS_ROBIN_TFT43, MKS_ROBIN_TFT_V1_1R, ANET_ET4_TFT28, ANET_ET5_TFT35) \ + + COUNT_ENABLED(TFTGLCD_PANEL_SPI, TFTGLCD_PANEL_I2C) \ + + COUNT_ENABLED(VIKI2, miniVIKI) \ + + COUNT_ENABLED(ZONESTAR_12864LCD, ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306) \ + + COUNT_ENABLED(ANET_FULL_GRAPHICS_LCD, ANET_FULL_GRAPHICS_LCD_ALT_WIRING) \ + + ENABLED(AZSMZ_12864) \ + + ENABLED(BQ_LCD_SMART_CONTROLLER) \ + + ENABLED(CARTESIO_UI) \ + + ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) \ + + ENABLED(FF_INTERFACEBOARD) \ + + ENABLED(FYSETC_242_OLED_12864) \ + + ENABLED(G3D_PANEL) \ + + ENABLED(LCD_FOR_MELZI) \ + + ENABLED(LCD_I2C_PANELOLU2) \ + + ENABLED(LCD_I2C_VIKI) \ + + ENABLED(LCM1602) \ + + ENABLED(LONGER_LK_TFT28) \ + + ENABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602) \ + + ENABLED(MAKRPANEL) \ + + ENABLED(MALYAN_LCD) \ + + ENABLED(MKS_LCD12864) \ + + ENABLED(OLED_PANEL_TINYBOY2) \ + + ENABLED(OVERLORD_OLED) \ + + ENABLED(PANEL_ONE) \ + + ENABLED(RA_CONTROL_PANEL) \ + + ENABLED(RADDS_DISPLAY) \ + + ENABLED(REPRAPWORLD_GRAPHICAL_LCD) \ + + ENABLED(RIGIDBOT_PANEL) \ + + ENABLED(SAV_3DGLCD) \ + + ENABLED(SAV_3DLCD) \ + + ENABLED(SILVER_GATE_GLCD_CONTROLLER) \ + + ENABLED(TFT_TRONXY_X5SA) \ + + ENABLED(TOUCH_UI_FTDI_EVE) \ + + ENABLED(U8GLIB_SH1106_EINSTART) \ + + ENABLED(ULTI_CONTROLLER) \ + + ENABLED(ULTIMAKERCONTROLLER) \ + + ENABLED(ZONESTAR_LCD) + #error "Please select only one LCD controller option." +#endif + +#undef IS_U8GLIB_SSD1306 +#undef IS_EXTUI +#undef IS_LEGACY_TFT + +#if ANY(TFT_GENERIC, MKS_TS35_V2_0, MKS_ROBIN_TFT24, MKS_ROBIN_TFT28, MKS_ROBIN_TFT32, MKS_ROBIN_TFT35, MKS_ROBIN_TFT43, MKS_ROBIN_TFT_V1_1R, TFT_TRONXY_X5SA, ANYCUBIC_TFT35, ANYCUBIC_TFT35, LONGER_LK_TFT28, ANET_ET4_TFT28, ANET_ET5_TFT35) + #if NONE(TFT_COLOR_UI, TFT_CLASSIC_UI, TFT_LVGL_UI) + #error "TFT_COLOR_UI, TFT_CLASSIC_UI, TFT_LVGL_UI is required for your TFT. Please enable one." + #elif 1 < ENABLED(TFT_COLOR_UI) + ENABLED(TFT_CLASSIC_UI) + ENABLED(TFT_LVGL_UI) + #error "Please select only one of TFT_COLOR_UI, TFT_CLASSIC_UI, or TFT_LVGL_UI." + #endif +#elif ANY(TFT_COLOR_UI, TFT_CLASSIC_UI, TFT_LVGL_UI) + #error "TFT_(COLOR|CLASSIC|LVGL)_UI requires a TFT display to be enabled." +#endif + +#if ENABLED(TFT_GENERIC) && NONE(TFT_INTERFACE_FSMC, TFT_INTERFACE_SPI) + #error "TFT_GENERIC requires either TFT_INTERFACE_FSMC or TFT_INTERFACE_SPI interface." +#endif + +#if BOTH(TFT_INTERFACE_FSMC, TFT_INTERFACE_SPI) + #error "Please enable only one of TFT_INTERFACE_SPI or TFT_INTERFACE_SPI." +#endif + +#if MANY(LCD_SCREEN_ROT_0, LCD_SCREEN_ROT_90, LCD_SCREEN_ROT_180, LCD_SCREEN_ROT_270) + #error "Please enable only one LCD_SCREEN_ROT_* option: 0, 90, 180, or 270." +#endif + +#if MANY(TFT_RES_320x240, TFT_RES_480x272, TFT_RES_480x320) + #error "Please select only one of TFT_RES_480x320, TFT_RES_480x320, or TFT_RES_480x272." +#endif + +#if HAS_TFT_LVGL_UI && DISABLED(TFT_RES_480x320) + #error "(FMSC|SPI)TFT_LVGL_UI requires TFT_RES_480x320." +#endif + +#if defined(GRAPHICAL_TFT_UPSCALE) && !WITHIN(GRAPHICAL_TFT_UPSCALE, 2, 3) + #error "GRAPHICAL_TFT_UPSCALE must be set to 2 or 3." +#endif + +/** + * Some boards forbid the use of -1 Native USB + */ +#if ENABLED(BOARD_NO_NATIVE_USB) + #undef BOARD_NO_NATIVE_USB + #if SERIAL_PORT == -1 + #error "SERIAL_PORT is set to -1, but the MOTHERBOARD has no native USB support. Set SERIAL_PORT to a valid value for your board." + #elif SERIAL_PORT_2 == -1 + #error "SERIAL_PORT_2 is set to -1, but the MOTHERBOARD has no native USB support. Set SERIAL_PORT_2 to a valid value for your board." + #elif MMU2_SERIAL_PORT == -1 + #error "MMU2_SERIAL_PORT is set to -1, but the MOTHERBOARD has no native USB support. Set MMU2_SERIAL_PORT to a valid value for your board." + #elif LCD_SERIAL_PORT == -1 + #error "LCD_SERIAL_PORT is set to -1, but the MOTHERBOARD has no native USB support. Set LCD_SERIAL_PORT to a valid value for your board." + #endif +#endif + +/** + * MMU2 require a dedicated serial port + */ +#ifdef MMU2_SERIAL_PORT + #if MMU2_SERIAL_PORT == SERIAL_PORT + #error "MMU2_SERIAL_PORT cannot be the same as SERIAL_PORT." + #elif defined(SERIAL_PORT_2) && MMU2_SERIAL_PORT == SERIAL_PORT_2 + #error "MMU2_SERIAL_PORT cannot be the same as SERIAL_PORT_2." + #elif defined(LCD_SERIAL_PORT) && MMU2_SERIAL_PORT == LCD_SERIAL_PORT + #error "MMU2_SERIAL_PORT cannot be the same as LCD_SERIAL_PORT." + #endif +#endif + +/** + * Serial displays require a dedicated serial port + */ +#ifdef LCD_SERIAL_PORT + #if LCD_SERIAL_PORT == SERIAL_PORT + #error "LCD_SERIAL_PORT cannot be the same as SERIAL_PORT." + #elif defined(SERIAL_PORT_2) && LCD_SERIAL_PORT == SERIAL_PORT_2 + #error "LCD_SERIAL_PORT cannot be the same as SERIAL_PORT_2." + #endif +#else + #if HAS_DGUS_LCD + #error "The DGUS LCD requires LCD_SERIAL_PORT to be defined." + #elif EITHER(ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON) + #error "The ANYCUBIC LCD requires LCD_SERIAL_PORT to be defined." + #elif ENABLED(MALYAN_LCD) + #error "MALYAN_LCD requires LCD_SERIAL_PORT to be defined." + #endif +#endif + +/** + * FYSETC Mini 12864 RGB backlighting required + */ +#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) && DISABLED(RGB_LED) + #error "RGB_LED is required for FYSETC_MINI_12864 1.2 and 2.0." +#elif EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1) && DISABLED(LED_USER_PRESET_STARTUP) + #error "LED_USER_PRESET_STARTUP is required for FYSETC_MINI_12864 2.x displays." +#endif + +/** + * Check existing CS pins against enabled TMC SPI drivers. + */ +#define INVALID_TMC_SPI(ST) (AXIS_HAS_SPI(ST) && !PIN_EXISTS(ST##_CS)) +#if INVALID_TMC_SPI(X) + #error "An SPI driven TMC driver on X requires X_CS_PIN." +#elif INVALID_TMC_SPI(X2) + #error "An SPI driven TMC driver on X2 requires X2_CS_PIN." +#elif INVALID_TMC_SPI(Y) + #error "An SPI driven TMC driver on Y requires Y_CS_PIN." +#elif INVALID_TMC_SPI(Y2) + #error "An SPI driven TMC driver on Y2 requires Y2_CS_PIN." +#elif INVALID_TMC_SPI(Z) + #error "An SPI driven TMC driver on Z requires Z_CS_PIN." +#elif INVALID_TMC_SPI(Z2) + #error "An SPI driven TMC driver on Z2 requires Z2_CS_PIN." +#elif INVALID_TMC_SPI(Z3) + #error "An SPI driven TMC driver on Z3 requires Z3_CS_PIN." +#elif INVALID_TMC_SPI(Z4) + #error "An SPI driven TMC driver on Z4 requires Z4_CS_PIN." +#elif INVALID_TMC_SPI(E0) + #error "An SPI driven TMC driver on E0 requires E0_CS_PIN." +#elif INVALID_TMC_SPI(E1) + #error "An SPI driven TMC driver on E1 requires E1_CS_PIN." +#elif INVALID_TMC_SPI(E2) + #error "An SPI driven TMC driver on E2 requires E2_CS_PIN." +#elif INVALID_TMC_SPI(E3) + #error "An SPI driven TMC driver on E3 requires E3_CS_PIN." +#elif INVALID_TMC_SPI(E4) + #error "An SPI driven TMC driver on E4 requires E4_CS_PIN." +#elif INVALID_TMC_SPI(E5) + #error "An SPI driven TMC driver on E5 requires E5_CS_PIN." +#elif INVALID_TMC_SPI(E6) + #error "An SPI driven TMC driver on E6 requires E6_CS_PIN." +#elif INVALID_TMC_SPI(E7) + #error "An SPI driven TMC driver on E7 requires E7_CS_PIN." +#endif +#undef INVALID_TMC_SPI + +/** + * Check existing RX/TX pins against enable TMC UART drivers. + */ +#define INVALID_TMC_UART(ST) (AXIS_HAS_UART(ST) && !(defined(ST##_HARDWARE_SERIAL) || (PINS_EXIST(ST##_SERIAL_RX, ST##_SERIAL_TX)))) +#if INVALID_TMC_UART(X) + #error "TMC2208 or TMC2209 on X requires X_HARDWARE_SERIAL or X_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(X2) + #error "TMC2208 or TMC2209 on X2 requires X2_HARDWARE_SERIAL or X2_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(Y) + #error "TMC2208 or TMC2209 on Y requires Y_HARDWARE_SERIAL or Y_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(Y2) + #error "TMC2208 or TMC2209 on Y2 requires Y2_HARDWARE_SERIAL or Y2_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(Z) + #error "TMC2208 or TMC2209 on Z requires Z_HARDWARE_SERIAL or Z_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(Z2) + #error "TMC2208 or TMC2209 on Z2 requires Z2_HARDWARE_SERIAL or Z2_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(Z3) + #error "TMC2208 or TMC2209 on Z3 requires Z3_HARDWARE_SERIAL or Z3_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(Z4) + #error "TMC2208 or TMC2209 on Z4 requires Z4_HARDWARE_SERIAL or Z4_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(E0) + #error "TMC2208 or TMC2209 on E0 requires E0_HARDWARE_SERIAL or E0_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(E1) + #error "TMC2208 or TMC2209 on E1 requires E1_HARDWARE_SERIAL or E1_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(E2) + #error "TMC2208 or TMC2209 on E2 requires E2_HARDWARE_SERIAL or E2_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(E3) + #error "TMC2208 or TMC2209 on E3 requires E3_HARDWARE_SERIAL or E3_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(E4) + #error "TMC2208 or TMC2209 on E4 requires E4_HARDWARE_SERIAL or E4_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(E5) + #error "TMC2208 or TMC2209 on E5 requires E5_HARDWARE_SERIAL or E5_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(E6) + #error "TMC2208 or TMC2209 on E6 requires E6_HARDWARE_SERIAL or E6_SERIAL_(RX|TX)_PIN." +#elif INVALID_TMC_UART(E7) + #error "TMC2208 or TMC2209 on E7 requires E7_HARDWARE_SERIAL or E7_SERIAL_(RX|TX)_PIN." +#endif +#undef INVALID_TMC_UART + +/** + * TMC2209 slave address values + */ +#define INVALID_TMC_ADDRESS(ST) static_assert(0 <= ST##_SLAVE_ADDRESS && ST##_SLAVE_ADDRESS <= 3, "TMC2209 slave address must be 0, 1, 2 or 3") +#if AXIS_DRIVER_TYPE_X(TMC2209) + INVALID_TMC_ADDRESS(X); +#elif AXIS_DRIVER_TYPE_X2(TMC2209) + INVALID_TMC_ADDRESS(X2); +#elif AXIS_DRIVER_TYPE_Y(TMC2209) + INVALID_TMC_ADDRESS(Y); +#elif AXIS_DRIVER_TYPE_Y2(TMC2209) + INVALID_TMC_ADDRESS(Y2); +#elif AXIS_DRIVER_TYPE_Z(TMC2209) + INVALID_TMC_ADDRESS(Z); +#elif AXIS_DRIVER_TYPE_Z2(TMC2209) + INVALID_TMC_ADDRESS(Z2); +#elif AXIS_DRIVER_TYPE_Z3(TMC2209) + INVALID_TMC_ADDRESS(Z3); +#elif AXIS_DRIVER_TYPE_Z4(TMC2209) + INVALID_TMC_ADDRESS(Z4); +#elif AXIS_DRIVER_TYPE_E0(TMC2209) + INVALID_TMC_ADDRESS(E0); +#elif AXIS_DRIVER_TYPE_E1(TMC2209) + INVALID_TMC_ADDRESS(E1); +#elif AXIS_DRIVER_TYPE_E2(TMC2209) + INVALID_TMC_ADDRESS(E2); +#elif AXIS_DRIVER_TYPE_E3(TMC2209) + INVALID_TMC_ADDRESS(E3); +#elif AXIS_DRIVER_TYPE_E4(TMC2209) + INVALID_TMC_ADDRESS(E4); +#elif AXIS_DRIVER_TYPE_E5(TMC2209) + INVALID_TMC_ADDRESS(E5); +#elif AXIS_DRIVER_TYPE_E6(TMC2209) + INVALID_TMC_ADDRESS(E6); +#elif AXIS_DRIVER_TYPE_E7(TMC2209) + INVALID_TMC_ADDRESS(E7); +#endif +#undef INVALID_TMC_ADDRESS + +#define _TMC_MICROSTEP_IS_VALID(MS) (MS == 0 || MS == 2 || MS == 4 || MS == 8 || MS == 16 || MS == 32 || MS == 64 || MS == 128 || MS == 256) +#define TMC_MICROSTEP_IS_VALID(M) (!AXIS_IS_TMC(M) || _TMC_MICROSTEP_IS_VALID(M##_MICROSTEPS)) +#define INVALID_TMC_MS(ST) static_assert(0, "Invalid " STRINGIFY(ST) "_MICROSTEPS. Valid values are 0, 2, 4, 8, 16, 32, 64, 128, and 256.") + +#if !TMC_MICROSTEP_IS_VALID(X) + INVALID_TMC_MS(X); +#elif !TMC_MICROSTEP_IS_VALID(Y) + INVALID_TMC_MS(Y) +#elif !TMC_MICROSTEP_IS_VALID(Z) + INVALID_TMC_MS(Z) +#elif !TMC_MICROSTEP_IS_VALID(X2) + INVALID_TMC_MS(X2); +#elif !TMC_MICROSTEP_IS_VALID(Y2) + INVALID_TMC_MS(Y2) +#elif !TMC_MICROSTEP_IS_VALID(Z2) + INVALID_TMC_MS(Z2) +#elif !TMC_MICROSTEP_IS_VALID(Z3) + INVALID_TMC_MS(Z3) +#elif !TMC_MICROSTEP_IS_VALID(Z4) + INVALID_TMC_MS(Z4) +#elif !TMC_MICROSTEP_IS_VALID(E0) + INVALID_TMC_MS(E0) +#elif !TMC_MICROSTEP_IS_VALID(E1) + INVALID_TMC_MS(E1) +#elif !TMC_MICROSTEP_IS_VALID(E2) + INVALID_TMC_MS(E2) +#elif !TMC_MICROSTEP_IS_VALID(E3) + INVALID_TMC_MS(E3) +#elif !TMC_MICROSTEP_IS_VALID(E4) + INVALID_TMC_MS(E4) +#elif !TMC_MICROSTEP_IS_VALID(E5) + INVALID_TMC_MS(E5) +#elif !TMC_MICROSTEP_IS_VALID(E6) + INVALID_TMC_MS(E6) +#elif !TMC_MICROSTEP_IS_VALID(E7) + INVALID_TMC_MS(E7) +#endif +#undef INVALID_TMC_MS +#undef TMC_MICROSTEP_IS_VALID +#undef _TMC_MICROSTEP_IS_VALID + +#if ENABLED(DELTA) && (ENABLED(STEALTHCHOP_XY) != ENABLED(STEALTHCHOP_Z)) + #error "STEALTHCHOP_XY and STEALTHCHOP_Z must be the same on DELTA." +#endif + +#if ENABLED(SENSORLESS_HOMING) + // Require STEALTHCHOP for SENSORLESS_HOMING on DELTA as the transition from spreadCycle to stealthChop + // is necessary in order to reset the stallGuard indication between the initial movement of all three + // towers to +Z and the individual homing of each tower. This restriction can be removed once a means of + // clearing the stallGuard activated status is found. + + // Stall detection DIAG = HIGH : TMC2209 + // Stall detection DIAG = LOW : TMC2130/TMC2160/TMC2660/TMC5130/TMC5160 + #define X_ENDSTOP_INVERTING !AXIS_DRIVER_TYPE(X,TMC2209) + #define Y_ENDSTOP_INVERTING !AXIS_DRIVER_TYPE(Y,TMC2209) + #define Z_ENDSTOP_INVERTING !AXIS_DRIVER_TYPE(Z,TMC2209) + + #if NONE(SPI_ENDSTOPS, ONBOARD_ENDSTOPPULLUPS, ENDSTOPPULLUPS) + #if X_SENSORLESS && X_HOME_DIR < 0 && DISABLED(ENDSTOPPULLUP_XMIN) + #error "SENSORLESS_HOMING requires ENDSTOPPULLUP_XMIN (or ENDSTOPPULLUPS) when homing to X_MIN." + #elif X_SENSORLESS && X_HOME_DIR > 0 && DISABLED(ENDSTOPPULLUP_XMAX) + #error "SENSORLESS_HOMING requires ENDSTOPPULLUP_XMAX (or ENDSTOPPULLUPS) when homing to X_MAX." + #elif Y_SENSORLESS && Y_HOME_DIR < 0 && DISABLED(ENDSTOPPULLUP_YMIN) + #error "SENSORLESS_HOMING requires ENDSTOPPULLUP_YMIN (or ENDSTOPPULLUPS) when homing to Y_MIN." + #elif Y_SENSORLESS && Y_HOME_DIR > 0 && DISABLED(ENDSTOPPULLUP_YMAX) + #error "SENSORLESS_HOMING requires ENDSTOPPULLUP_YMAX (or ENDSTOPPULLUPS) when homing to Y_MAX." + #elif Z_SENSORLESS && Z_HOME_DIR < 0 && DISABLED(ENDSTOPPULLUP_ZMIN) + #error "SENSORLESS_HOMING requires ENDSTOPPULLUP_ZMIN (or ENDSTOPPULLUPS) when homing to Z_MIN." + #elif Z_SENSORLESS && Z_HOME_DIR > 0 && DISABLED(ENDSTOPPULLUP_ZMAX) + #error "SENSORLESS_HOMING requires ENDSTOPPULLUP_ZMAX (or ENDSTOPPULLUPS) when homing to Z_MAX." + #endif + #endif + + #if ENABLED(SPI_ENDSTOPS) + #if ENABLED(QUICK_HOME) + #warning "SPI_ENDSTOPS may be unreliable with QUICK_HOME. Adjust back-offs for better results." + #endif + #else + #if X_SENSORLESS && X_HOME_DIR < 0 && X_MIN_ENDSTOP_INVERTING != X_ENDSTOP_INVERTING + #if X_ENDSTOP_INVERTING + #error "SENSORLESS_HOMING requires X_MIN_ENDSTOP_INVERTING = true when homing to X_MIN." + #else + #error "SENSORLESS_HOMING requires X_MIN_ENDSTOP_INVERTING = false when homing TMC2209 to X_MIN." + #endif + #elif X_SENSORLESS && X_HOME_DIR > 0 && X_MAX_ENDSTOP_INVERTING != X_ENDSTOP_INVERTING + #if X_ENDSTOP_INVERTING + #error "SENSORLESS_HOMING requires X_MAX_ENDSTOP_INVERTING = true when homing to X_MAX." + #else + #error "SENSORLESS_HOMING requires X_MAX_ENDSTOP_INVERTING = false when homing TMC2209 to X_MAX." + #endif + #elif Y_SENSORLESS && Y_HOME_DIR < 0 && Y_MIN_ENDSTOP_INVERTING != Y_ENDSTOP_INVERTING + #if Y_ENDSTOP_INVERTING + #error "SENSORLESS_HOMING requires Y_MIN_ENDSTOP_INVERTING = true when homing to Y_MIN." + #else + #error "SENSORLESS_HOMING requires Y_MIN_ENDSTOP_INVERTING = false when homing TMC2209 to Y_MIN." + #endif + #elif Y_SENSORLESS && Y_HOME_DIR > 0 && Y_MAX_ENDSTOP_INVERTING != Y_ENDSTOP_INVERTING + #if Y_ENDSTOP_INVERTING + #error "SENSORLESS_HOMING requires Y_MAX_ENDSTOP_INVERTING = true when homing to Y_MAX." + #else + #error "SENSORLESS_HOMING requires Y_MAX_ENDSTOP_INVERTING = false when homing TMC2209 to Y_MAX." + #endif + #elif Z_SENSORLESS && Z_HOME_DIR < 0 && Z_MIN_ENDSTOP_INVERTING != Z_ENDSTOP_INVERTING + #if Z_ENDSTOP_INVERTING + #error "SENSORLESS_HOMING requires Z_MIN_ENDSTOP_INVERTING = true when homing to Z_MIN." + #else + #error "SENSORLESS_HOMING requires Z_MIN_ENDSTOP_INVERTING = false when homing TMC2209 to Z_MIN." + #endif + #elif Z_SENSORLESS && Z_HOME_DIR > 0 && Z_MAX_ENDSTOP_INVERTING != Z_ENDSTOP_INVERTING + #if Z_ENDSTOP_INVERTING + #error "SENSORLESS_HOMING requires Z_MAX_ENDSTOP_INVERTING = true when homing to Z_MAX." + #else + #error "SENSORLESS_HOMING requires Z_MAX_ENDSTOP_INVERTING = false when homing TMC2209 to Z_MAX." + #endif + #endif + #endif + + #if ENABLED(DELTA) && !BOTH(STEALTHCHOP_XY, STEALTHCHOP_Z) + #error "SENSORLESS_HOMING on DELTA currently requires STEALTHCHOP_XY and STEALTHCHOP_Z." + #elif ENDSTOP_NOISE_THRESHOLD + #error "SENSORLESS_HOMING is incompatible with ENDSTOP_NOISE_THRESHOLD." + #elif !(X_SENSORLESS || Y_SENSORLESS || Z_SENSORLESS) + #error "SENSORLESS_HOMING requires a TMC stepper driver with StallGuard on X, Y, or Z axes." + #endif + + #undef X_ENDSTOP_INVERTING + #undef Y_ENDSTOP_INVERTING + #undef Z_ENDSTOP_INVERTING +#endif + +// Sensorless probing requirements +#if ENABLED(SENSORLESS_PROBING) + #if ENABLED(DELTA) && !(X_SENSORLESS && Y_SENSORLESS && Z_SENSORLESS) + #error "SENSORLESS_PROBING for DELTA requires TMC stepper drivers with StallGuard on X, Y, and Z axes." + #elif ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) + #error "SENSORLESS_PROBING cannot be used with Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN." + #elif ENABLED(USE_PROBE_FOR_Z_HOMING) + #error "SENSORLESS_PROBING cannot be used with USE_PROBE_FOR_Z_HOMING." + #elif !Z_SENSORLESS + #error "SENSORLESS_PROBING requires a TMC stepper driver with StallGuard on Z." + #endif +#endif + +// Sensorless homing is required for both combined steppers in an H-bot +#if CORE_IS_XY && X_SENSORLESS != Y_SENSORLESS + #error "CoreXY requires both X and Y to use sensorless homing if either one does." +#elif CORE_IS_XZ && X_SENSORLESS != Z_SENSORLESS && !HOMING_Z_WITH_PROBE + #error "CoreXZ requires both X and Z to use sensorless homing if either one does." +#elif CORE_IS_YZ && Y_SENSORLESS != Z_SENSORLESS && !HOMING_Z_WITH_PROBE + #error "CoreYZ requires both Y and Z to use sensorless homing if either one does." +#elif ENABLED(MARKFORGED_XY) && X_SENSORLESS != Y_SENSORLESS + #error "MARKFORGED_XY requires both X and Y to use sensorless homing if either one does." +#endif + +// Other TMC feature requirements +#if ENABLED(HYBRID_THRESHOLD) && !STEALTHCHOP_ENABLED + #error "Enable STEALTHCHOP_(XY|Z|E) to use HYBRID_THRESHOLD." +#elif ENABLED(SENSORLESS_HOMING) && !HAS_STALLGUARD + #error "SENSORLESS_HOMING requires TMC2130, TMC2160, TMC2209, TMC2660, or TMC5160 stepper drivers." +#elif ENABLED(SENSORLESS_PROBING) && !HAS_STALLGUARD + #error "SENSORLESS_PROBING requires TMC2130, TMC2160, TMC2209, TMC2660, or TMC5160 stepper drivers." +#elif STEALTHCHOP_ENABLED && !HAS_STEALTHCHOP + #error "STEALTHCHOP requires TMC2130, TMC2160, TMC2208, TMC2209, or TMC5160 stepper drivers." +#endif + +/** + * TMC SPI Chaining + */ +#define IN_CHAIN(A) ((A##_CHAIN_POS > 0) && !HAS_L64XX) +#if IN_CHAIN(X ) || IN_CHAIN(Y ) || IN_CHAIN(Z ) || IN_CHAIN(X2) || IN_CHAIN(Y2) || IN_CHAIN(Z2) || IN_CHAIN(Z3) || IN_CHAIN(Z4) \ + || IN_CHAIN(E0) || IN_CHAIN(E1) || IN_CHAIN(E2) || IN_CHAIN(E3) || IN_CHAIN(E4) || IN_CHAIN(E5) || IN_CHAIN(E6) || IN_CHAIN(E7) + #define BAD_CHAIN(A) (IN_CHAIN(A) && !PIN_EXISTS(A##_CS)) + #if BAD_CHAIN(X ) || BAD_CHAIN(Y ) || BAD_CHAIN(Z ) || BAD_CHAIN(X2) || BAD_CHAIN(Y2) || BAD_CHAIN(Z2) || BAD_CHAIN(Z3) || BAD_CHAIN(Z4) \ + || BAD_CHAIN(E0) || BAD_CHAIN(E1) || BAD_CHAIN(E2) || BAD_CHAIN(E3) || BAD_CHAIN(E4) || BAD_CHAIN(E5) || BAD_CHAIN(E6) || BAD_CHAIN(E7) + #error "All chained TMC drivers need a CS pin." + #else + #if IN_CHAIN(X) + #define CS_COMPARE X_CS_PIN + #elif IN_CHAIN(Y) + #define CS_COMPARE Y_CS_PIN + #elif IN_CHAIN(Z) + #define CS_COMPARE Z_CS_PIN + #elif IN_CHAIN(X2) + #define CS_COMPARE X2_CS_PIN + #elif IN_CHAIN(Y2) + #define CS_COMPARE Y2_CS_PIN + #elif IN_CHAIN(Z2) + #define CS_COMPARE Z2_CS_PIN + #elif IN_CHAIN(Z3) + #define CS_COMPARE Z3_CS_PIN + #elif IN_CHAIN(E0) + #define CS_COMPARE E0_CS_PIN + #elif IN_CHAIN(E1) + #define CS_COMPARE E1_CS_PIN + #elif IN_CHAIN(E2) + #define CS_COMPARE E2_CS_PIN + #elif IN_CHAIN(E3) + #define CS_COMPARE E3_CS_PIN + #elif IN_CHAIN(E4) + #define CS_COMPARE E4_CS_PIN + #elif IN_CHAIN(E5) + #define CS_COMPARE E5_CS_PIN + #elif IN_CHAIN(E6) + #define CS_COMPARE E6_CS_PIN + #elif IN_CHAIN(E7) + #define CS_COMPARE E7_CS_PIN + #endif + #define BAD_CS_PIN(A) (IN_CHAIN(A) && A##_CS_PIN != CS_COMPARE) + #if BAD_CS_PIN(X ) || BAD_CS_PIN(Y ) || BAD_CS_PIN(Z ) || BAD_CS_PIN(X2) || BAD_CS_PIN(Y2) || BAD_CS_PIN(Z2) || BAD_CS_PIN(Z3) || BAD_CS_PIN(Z4) \ + || BAD_CS_PIN(E0) || BAD_CS_PIN(E1) || BAD_CS_PIN(E2) || BAD_CS_PIN(E3) || BAD_CS_PIN(E4) || BAD_CS_PIN(E5) || BAD_CS_PIN(E6) || BAD_CS_PIN(E7) + #error "All chained TMC drivers must use the same CS pin." + #endif + #undef BAD_CS_PIN + #undef CS_COMPARE + #endif + #undef BAD_CHAIN +#endif +#undef IN_CHAIN + +/** + * Digipot requirement + */ +#if HAS_MOTOR_CURRENT_I2C + #if BOTH(DIGIPOT_MCP4018, DIGIPOT_MCP4451) + #error "Enable only one of DIGIPOT_MCP4018 or DIGIPOT_MCP4451." + #elif !MB(MKS_SBASE) \ + && (!defined(DIGIPOTS_I2C_SDA_X) || !defined(DIGIPOTS_I2C_SDA_Y) || !defined(DIGIPOTS_I2C_SDA_Z) || !defined(DIGIPOTS_I2C_SDA_E0) || !defined(DIGIPOTS_I2C_SDA_E1)) + #error "DIGIPOT_MCP4018/4451 requires DIGIPOTS_I2C_SDA_* pins to be defined." + #endif +#endif + +/** + * Check per-axis initializers for errors + */ +constexpr float sanity_arr_1[] = DEFAULT_AXIS_STEPS_PER_UNIT, + sanity_arr_2[] = DEFAULT_MAX_FEEDRATE, + sanity_arr_3[] = DEFAULT_MAX_ACCELERATION; + +#define _ARR_TEST(N,I) (sanity_arr_##N[_MIN(I,int(COUNT(sanity_arr_##N))-1)] > 0) + +static_assert(COUNT(sanity_arr_1) >= XYZE, "DEFAULT_AXIS_STEPS_PER_UNIT requires X, Y, Z and E elements."); +static_assert(COUNT(sanity_arr_1) <= XYZE_N, "DEFAULT_AXIS_STEPS_PER_UNIT has too many elements. (Did you forget to enable DISTINCT_E_FACTORS?)"); +static_assert( _ARR_TEST(1,0) && _ARR_TEST(1,1) && _ARR_TEST(1,2) + && _ARR_TEST(1,3) && _ARR_TEST(1,4) && _ARR_TEST(1,5) + && _ARR_TEST(1,6) && _ARR_TEST(1,7) && _ARR_TEST(1,8), + "DEFAULT_AXIS_STEPS_PER_UNIT values must be positive."); + +static_assert(COUNT(sanity_arr_2) >= XYZE, "DEFAULT_MAX_FEEDRATE requires X, Y, Z and E elements."); +static_assert(COUNT(sanity_arr_2) <= XYZE_N, "DEFAULT_MAX_FEEDRATE has too many elements. (Did you forget to enable DISTINCT_E_FACTORS?)"); +static_assert( _ARR_TEST(2,0) && _ARR_TEST(2,1) && _ARR_TEST(2,2) + && _ARR_TEST(2,3) && _ARR_TEST(2,4) && _ARR_TEST(2,5) + && _ARR_TEST(2,6) && _ARR_TEST(2,7) && _ARR_TEST(2,8), + "DEFAULT_MAX_FEEDRATE values must be positive."); + +static_assert(COUNT(sanity_arr_3) >= XYZE, "DEFAULT_MAX_ACCELERATION requires X, Y, Z and E elements."); +static_assert(COUNT(sanity_arr_3) <= XYZE_N, "DEFAULT_MAX_ACCELERATION has too many elements. (Did you forget to enable DISTINCT_E_FACTORS?)"); +static_assert( _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2) + && _ARR_TEST(3,3) && _ARR_TEST(3,4) && _ARR_TEST(3,5) + && _ARR_TEST(3,6) && _ARR_TEST(3,7) && _ARR_TEST(3,8), + "DEFAULT_MAX_ACCELERATION values must be positive."); + +#if ENABLED(LIMITED_MAX_ACCEL_EDITING) + #ifdef MAX_ACCEL_EDIT_VALUES + constexpr float sanity_arr_4[] = MAX_ACCEL_EDIT_VALUES; + static_assert(COUNT(sanity_arr_4) >= XYZE, "MAX_ACCEL_EDIT_VALUES requires X, Y, Z and E elements."); + static_assert(COUNT(sanity_arr_4) <= XYZE, "MAX_ACCEL_EDIT_VALUES has too many elements. X, Y, Z and E elements only."); + static_assert( _ARR_TEST(4,0) && _ARR_TEST(4,1) && _ARR_TEST(4,2) + && _ARR_TEST(4,3) && _ARR_TEST(4,4) && _ARR_TEST(4,5) + && _ARR_TEST(4,6) && _ARR_TEST(4,7) && _ARR_TEST(4,8), + "MAX_ACCEL_EDIT_VALUES values must be positive."); + #endif +#endif + +#if ENABLED(LIMITED_MAX_FR_EDITING) + #ifdef MAX_FEEDRATE_EDIT_VALUES + constexpr float sanity_arr_5[] = MAX_FEEDRATE_EDIT_VALUES; + static_assert(COUNT(sanity_arr_5) >= XYZE, "MAX_FEEDRATE_EDIT_VALUES requires X, Y, Z and E elements."); + static_assert(COUNT(sanity_arr_5) <= XYZE, "MAX_FEEDRATE_EDIT_VALUES has too many elements. X, Y, Z and E elements only."); + static_assert( _ARR_TEST(5,0) && _ARR_TEST(5,1) && _ARR_TEST(5,2) + && _ARR_TEST(5,3) && _ARR_TEST(5,4) && _ARR_TEST(5,5) + && _ARR_TEST(5,6) && _ARR_TEST(5,7) && _ARR_TEST(5,8), + "MAX_FEEDRATE_EDIT_VALUES values must be positive."); + #endif +#endif + +#if ENABLED(LIMITED_JERK_EDITING) + #ifdef MAX_JERK_EDIT_VALUES + constexpr float sanity_arr_6[] = MAX_JERK_EDIT_VALUES; + static_assert(COUNT(sanity_arr_6) >= XYZE, "MAX_JERK_EDIT_VALUES requires X, Y, Z and E elements."); + static_assert(COUNT(sanity_arr_6) <= XYZE, "MAX_JERK_EDIT_VALUES has too many elements. X, Y, Z and E elements only."); + static_assert( _ARR_TEST(6,0) && _ARR_TEST(6,1) && _ARR_TEST(6,2) + && _ARR_TEST(6,3) && _ARR_TEST(6,4) && _ARR_TEST(6,5) + && _ARR_TEST(6,6) && _ARR_TEST(6,7) && _ARR_TEST(6,8), + "MAX_JERK_EDIT_VALUES values must be positive."); + #endif +#endif + +#undef _ARR_TEST + +#if BOTH(CNC_COORDINATE_SYSTEMS, NO_WORKSPACE_OFFSETS) + #error "CNC_COORDINATE_SYSTEMS is incompatible with NO_WORKSPACE_OFFSETS." +#endif + +#if !BLOCK_BUFFER_SIZE || !IS_POWER_OF_2(BLOCK_BUFFER_SIZE) + #error "BLOCK_BUFFER_SIZE must be a power of 2." +#elif BLOCK_BUFFER_SIZE > 64 + #error "A very large BLOCK_BUFFER_SIZE is not needed and takes longer to drain the buffer on pause / cancel." +#endif + +#if ENABLED(LED_CONTROL_MENU) && !IS_ULTIPANEL + #error "LED_CONTROL_MENU requires an LCD controller." +#endif + +#if ENABLED(CASE_LIGHT_USE_NEOPIXEL) && DISABLED(NEOPIXEL_LED) + #error "CASE_LIGHT_USE_NEOPIXEL requires NEOPIXEL_LED." +#endif + +#if ENABLED(SKEW_CORRECTION) + #if !defined(XY_SKEW_FACTOR) && !(defined(XY_DIAG_AC) && defined(XY_DIAG_BD) && defined(XY_SIDE_AD)) + #error "SKEW_CORRECTION requires XY_SKEW_FACTOR or XY_DIAG_AC, XY_DIAG_BD, XY_SIDE_AD." + #endif + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #if !defined(XZ_SKEW_FACTOR) && !(defined(XZ_DIAG_AC) && defined(XZ_DIAG_BD) && defined(XZ_SIDE_AD)) + #error "SKEW_CORRECTION requires XZ_SKEW_FACTOR or XZ_DIAG_AC, XZ_DIAG_BD, XZ_SIDE_AD." + #endif + #if !defined(YZ_SKEW_FACTOR) && !(defined(YZ_DIAG_AC) && defined(YZ_DIAG_BD) && defined(YZ_SIDE_AD)) + #error "SKEW_CORRECTION requires YZ_SKEW_FACTOR or YZ_DIAG_AC, YZ_DIAG_BD, YZ_SIDE_AD." + #endif + #endif +#endif + +#if ENABLED(BACKUP_POWER_SUPPLY) && !PIN_EXISTS(POWER_LOSS) + #error "BACKUP_POWER_SUPPLY requires a POWER_LOSS_PIN." +#endif + +#if BOTH(POWER_LOSS_PULLUP, POWER_LOSS_PULLDOWN) + #error "You can't enable POWER_LOSS_PULLUP and POWER_LOSS_PULLDOWN at the same time." +#endif + +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + #if NUM_Z_STEPPER_DRIVERS <= 1 + #error "Z_STEPPER_AUTO_ALIGN requires NUM_Z_STEPPER_DRIVERS greater than 1." + #elif !HAS_BED_PROBE + #error "Z_STEPPER_AUTO_ALIGN requires a Z-bed probe." + #elif ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS) + static_assert(WITHIN(Z_STEPPER_ALIGN_AMP, 0.5, 2.0), "Z_STEPPER_ALIGN_AMP must be between 0.5 and 2.0."); + #if NUM_Z_STEPPER_DRIVERS < 3 + #error "Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS requires NUM_Z_STEPPER_DRIVERS to be 3 or 4." + #endif + #endif +#endif + +#if ENABLED(MECHANICAL_GANTRY_CALIBRATION) + #if NONE(HAS_MOTOR_CURRENT_DAC, HAS_MOTOR_CURRENT_SPI, HAS_MOTOR_CURRENT_DAC, HAS_TRINAMIC_CONFIG, HAS_MOTOR_CURRENT_PWM) + #error "It is highly recommended to have adjustable current drivers to prevent damage. Disable this line to continue anyway." + #elif !defined(GANTRY_CALIBRATION_CURRENT) + #error "MECHANICAL_GANTRY_CALIBRATION Requires GANTRY_CALIBRATION_CURRENT to be set." + #elif !defined(GANTRY_CALIBRATION_EXTRA_HEIGHT) + #error "MECHANICAL_GANTRY_CALIBRATION Requires GANTRY_CALIBRATION_EXTRA_HEIGHT to be set." + #elif !defined(GANTRY_CALIBRATION_FEEDRATE) + #error "MECHANICAL_GANTRY_CALIBRATION Requires GANTRY_CALIBRATION_FEEDRATE to be set." + #endif + #if defined(GANTRY_CALIBRATION_SAFE_POSITION) && !defined(GANTRY_CALIBRATION_XY_PARK_FEEDRATE) + #error "GANTRY_CALIBRATION_SAFE_POSITION Requires GANTRY_CALIBRATION_XY_PARK_FEEDRATE to be set." + #endif +#endif + +#if BOTH(Z_STEPPER_AUTO_ALIGN, MECHANICAL_GANTRY_CALIBRATION) + #error "You cannot use Z_STEPPER_AUTO_ALIGN and MECHANICAL_GANTRY_CALIBRATION at the same time." +#endif + +#if ENABLED(PRINTCOUNTER) && DISABLED(EEPROM_SETTINGS) + #error "PRINTCOUNTER requires EEPROM_SETTINGS." +#endif + +#if ENABLED(USB_FLASH_DRIVE_SUPPORT) && !PINS_EXIST(USB_CS, USB_INTR) && DISABLED(USE_OTG_USB_HOST) + #error "USB_CS_PIN and USB_INTR_PIN are required for USB_FLASH_DRIVE_SUPPORT." +#endif + +#if ENABLED(USE_OTG_USB_HOST) && !defined(HAS_OTG_USB_HOST_SUPPORT) + #error "The current board does not support USE_OTG_USB_HOST." +#endif + +#if ENABLED(SD_FIRMWARE_UPDATE) && !defined(__AVR_ATmega2560__) + #error "SD_FIRMWARE_UPDATE requires an ATmega2560-based (Arduino Mega) board." +#endif + +#if ENABLED(GCODE_MACROS) && !WITHIN(GCODE_MACROS_SLOTS, 1, 10) + #error "GCODE_MACROS_SLOTS must be a number from 1 to 10." +#endif + +#if ENABLED(CUSTOM_USER_MENUS) + #ifdef USER_GCODE_1 + constexpr char _chr1 = USER_GCODE_1[strlen(USER_GCODE_1) - 1]; + static_assert(_chr1 != '\n' && _chr1 != '\r', "USER_GCODE_1 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_2 + constexpr char _chr2 = USER_GCODE_2[strlen(USER_GCODE_2) - 1]; + static_assert(_chr2 != '\n' && _chr2 != '\r', "USER_GCODE_2 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_3 + constexpr char _chr3 = USER_GCODE_3[strlen(USER_GCODE_3) - 1]; + static_assert(_chr3 != '\n' && _chr3 != '\r', "USER_GCODE_3 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_4 + constexpr char _chr4 = USER_GCODE_4[strlen(USER_GCODE_4) - 1]; + static_assert(_chr4 != '\n' && _chr4 != '\r', "USER_GCODE_4 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_5 + constexpr char _chr5 = USER_GCODE_5[strlen(USER_GCODE_5) - 1]; + static_assert(_chr5 != '\n' && _chr5 != '\r', "USER_GCODE_5 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_6 + constexpr char _chr6 = USER_GCODE_6[strlen(USER_GCODE_6) - 1]; + static_assert(_chr6 != '\n' && _chr6 != '\r', "USER_GCODE_6 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_7 + constexpr char _chr7 = USER_GCODE_7[strlen(USER_GCODE_7) - 1]; + static_assert(_chr7 != '\n' && _chr7 != '\r', "USER_GCODE_7 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_8 + constexpr char _chr8 = USER_GCODE_8[strlen(USER_GCODE_8) - 1]; + static_assert(_chr8 != '\n' && _chr8 != '\r', "USER_GCODE_8 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_9 + constexpr char _chr9 = USER_GCODE_9[strlen(USER_GCODE_9) - 1]; + static_assert(_chr9 != '\n' && _chr9 != '\r', "USER_GCODE_9 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_10 + constexpr char _chr10 = USER_GCODE_10[strlen(USER_GCODE_10) - 1]; + static_assert(_chr10 != '\n' && _chr10 != '\r', "USER_GCODE_10 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_11 + constexpr char _chr11 = USER_GCODE_11[strlen(USER_GCODE_11) - 1]; + static_assert(_chr11 != '\n' && _chr11 != '\r', "USER_GCODE_11 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_12 + constexpr char _chr12 = USER_GCODE_12[strlen(USER_GCODE_12) - 1]; + static_assert(_chr12 != '\n' && _chr12 != '\r', "USER_GCODE_12 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_13 + constexpr char _chr13 = USER_GCODE_13[strlen(USER_GCODE_13) - 1]; + static_assert(_chr13 != '\n' && _chr13 != '\r', "USER_GCODE_13 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_14 + constexpr char _chr14 = USER_GCODE_14[strlen(USER_GCODE_14) - 1]; + static_assert(_chr14 != '\n' && _chr14 != '\r', "USER_GCODE_14 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_15 + constexpr char _chr15 = USER_GCODE_15[strlen(USER_GCODE_15) - 1]; + static_assert(_chr15 != '\n' && _chr15 != '\r', "USER_GCODE_15 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_16 + constexpr char _chr16 = USER_GCODE_16[strlen(USER_GCODE_16) - 1]; + static_assert(_chr16 != '\n' && _chr16 != '\r', "USER_GCODE_16 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_17 + constexpr char _chr17 = USER_GCODE_17[strlen(USER_GCODE_17) - 1]; + static_assert(_chr17 != '\n' && _chr17 != '\r', "USER_GCODE_17 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_18 + constexpr char _chr18 = USER_GCODE_18[strlen(USER_GCODE_18) - 1]; + static_assert(_chr18 != '\n' && _chr18 != '\r', "USER_GCODE_18 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_19 + constexpr char _chr19 = USER_GCODE_19[strlen(USER_GCODE_19) - 1]; + static_assert(_chr19 != '\n' && _chr19 != '\r', "USER_GCODE_19 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_20 + constexpr char _chr20 = USER_GCODE_20[strlen(USER_GCODE_20) - 1]; + static_assert(_chr20 != '\n' && _chr20 != '\r', "USER_GCODE_20 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_21 + constexpr char _chr21 = USER_GCODE_21[strlen(USER_GCODE_21) - 1]; + static_assert(_chr21 != '\n' && _chr21 != '\r', "USER_GCODE_21 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_22 + constexpr char _chr22 = USER_GCODE_22[strlen(USER_GCODE_22) - 1]; + static_assert(_chr22 != '\n' && _chr22 != '\r', "USER_GCODE_22 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_23 + constexpr char _chr23 = USER_GCODE_23[strlen(USER_GCODE_23) - 1]; + static_assert(_chr23 != '\n' && _chr23 != '\r', "USER_GCODE_23 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_24 + constexpr char _chr24 = USER_GCODE_24[strlen(USER_GCODE_24) - 1]; + static_assert(_chr24 != '\n' && _chr24 != '\r', "USER_GCODE_24 cannot have a newline at the end. Please remove it."); + #endif + #ifdef USER_GCODE_25 + constexpr char _chr25 = USER_GCODE_25[strlen(USER_GCODE_25) - 1]; + static_assert(_chr25 != '\n' && _chr25 != '\r', "USER_GCODE_25 cannot have a newline at the end. Please remove it."); + #endif +#endif + +#if ENABLED(BACKLASH_COMPENSATION) + #ifndef BACKLASH_DISTANCE_MM + #error "BACKLASH_COMPENSATION requires BACKLASH_DISTANCE_MM." + #elif !defined(BACKLASH_CORRECTION) + #error "BACKLASH_COMPENSATION requires BACKLASH_CORRECTION." + #elif ENABLED(MARKFORGED_XY) + constexpr float backlash_arr[] = BACKLASH_DISTANCE_MM; + static_assert(!backlash_arr[CORE_AXIS_1] && !backlash_arr[CORE_AXIS_2], + "BACKLASH_COMPENSATION can only apply to " STRINGIFY(NORMAL_AXIS) " on a MarkForged system."); + #elif IS_CORE + constexpr float backlash_arr[] = BACKLASH_DISTANCE_MM; + static_assert(!backlash_arr[CORE_AXIS_1] && !backlash_arr[CORE_AXIS_2], + "BACKLASH_COMPENSATION can only apply to " STRINGIFY(NORMAL_AXIS) " with your CORE system."); + #endif +#endif + +#if ENABLED(GRADIENT_MIX) && MIXING_VIRTUAL_TOOLS < 2 + #error "GRADIENT_MIX requires 2 or more MIXING_VIRTUAL_TOOLS." +#endif + +/** + * Photo G-code requirements + */ +#if ENABLED(PHOTO_GCODE) + #if (PIN_EXISTS(CHDK) + PIN_EXISTS(PHOTOGRAPH) + defined(PHOTO_SWITCH_POSITION)) > 1 + #error "Please define only one of CHDK_PIN, PHOTOGRAPH_PIN, or PHOTO_SWITCH_POSITION." + #elif defined(PHOTO_SWITCH_POSITION) && !defined(PHOTO_POSITION) + #error "PHOTO_SWITCH_POSITION requires PHOTO_POSITION." + #elif PIN_EXISTS(CHDK) && defined(CHDK_DELAY) + #error "CHDK_DELAY has been replaced by PHOTO_SWITCH_MS." + #elif PIN_EXISTS(CHDK) && !defined(PHOTO_SWITCH_MS) + #error "PHOTO_SWITCH_MS is required with CHDK_PIN." + #elif defined(PHOTO_RETRACT_MM) + static_assert(PHOTO_RETRACT_MM + 0 >= 0, "PHOTO_RETRACT_MM must be >= 0."); + #endif +#endif + +/** + * Advanced PRINTCOUNTER settings + */ +#if ENABLED(PRINTCOUNTER) + #if defined(SERVICE_INTERVAL_1) != defined(SERVICE_NAME_1) + #error "Both SERVICE_NAME_1 and SERVICE_INTERVAL_1 are required." + #elif defined(SERVICE_INTERVAL_2) != defined(SERVICE_NAME_2) + #error "Both SERVICE_NAME_2 and SERVICE_INTERVAL_2 are required." + #elif defined(SERVICE_INTERVAL_3) != defined(SERVICE_NAME_3) + #error "Both SERVICE_NAME_3 and SERVICE_INTERVAL_3 are required." + #endif +#endif + +/** + * Require soft endstops for certain setups + */ +#if !BOTH(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) + #if ENABLED(DUAL_X_CARRIAGE) + #error "DUAL_X_CARRIAGE requires both MIN_ and MAX_SOFTWARE_ENDSTOPS." + #elif HAS_HOTEND_OFFSET + #error "MIN_ and MAX_SOFTWARE_ENDSTOPS are both required with offset hotends." + #endif +#endif + +/** + * Ensure this option is set intentionally + */ +#if ENABLED(PSU_CONTROL) + #ifndef PSU_ACTIVE_STATE + #error "PSU_CONTROL requires PSU_ACTIVE_STATE to be defined as 'HIGH' or 'LOW'." + #elif !PIN_EXISTS(PS_ON) + #error "PSU_CONTROL requires PS_ON_PIN." + #elif POWER_OFF_DELAY < 0 + #error "POWER_OFF_DELAY must be a positive value." + #endif +#endif + +#if HAS_CUTTER + #ifndef CUTTER_POWER_UNIT + #error "CUTTER_POWER_UNIT is required with a spindle or laser." + #elif !CUTTER_UNIT_IS(PWM255) && !CUTTER_UNIT_IS(PERCENT) && !CUTTER_UNIT_IS(RPM) && !CUTTER_UNIT_IS(SERVO) + #error "CUTTER_POWER_UNIT must be PWM255, PERCENT, RPM, or SERVO." + #endif + + #if ENABLED(LASER_POWER_INLINE) + #if ENABLED(SPINDLE_CHANGE_DIR) + #error "SPINDLE_CHANGE_DIR and LASER_POWER_INLINE are incompatible." + #elif ENABLED(LASER_MOVE_G0_OFF) && DISABLED(LASER_MOVE_POWER) + #error "LASER_MOVE_G0_OFF requires LASER_MOVE_POWER." + #endif + #if ENABLED(LASER_POWER_INLINE_TRAPEZOID) + #if DISABLED(SPINDLE_LASER_PWM) + #error "LASER_POWER_INLINE_TRAPEZOID requires SPINDLE_LASER_PWM to function." + #elif ENABLED(S_CURVE_ACCELERATION) + //#ifndef LASER_POWER_INLINE_S_CURVE_ACCELERATION_WARN + // #define LASER_POWER_INLINE_S_CURVE_ACCELERATION_WARN + // #warning "Combining LASER_POWER_INLINE_TRAPEZOID with S_CURVE_ACCELERATION may result in unintended behavior." + //#endif + #endif + #endif + #if ENABLED(LASER_POWER_INLINE_INVERT) + //#ifndef LASER_POWER_INLINE_INVERT_WARN + // #define LASER_POWER_INLINE_INVERT_WARN + // #warning "Enabling LASER_POWER_INLINE_INVERT means that `M5` won't kill the laser immediately; use `M5 I` instead." + //#endif + #endif + #else + #if SPINDLE_LASER_POWERUP_DELAY < 1 + #error "SPINDLE_LASER_POWERUP_DELAY must be greater than 0." + #elif SPINDLE_LASER_POWERDOWN_DELAY < 1 + #error "SPINDLE_LASER_POWERDOWN_DELAY must be greater than 0." + #elif ENABLED(LASER_MOVE_POWER) + #error "LASER_MOVE_POWER requires LASER_POWER_INLINE." + #elif ANY(LASER_POWER_INLINE_TRAPEZOID, LASER_POWER_INLINE_INVERT, LASER_MOVE_G0_OFF, LASER_MOVE_POWER) + #error "Enabled an inline laser feature without inline laser power being enabled." + #endif + #endif + #define _PIN_CONFLICT(P) (PIN_EXISTS(P) && P##_PIN == SPINDLE_LASER_PWM_PIN) + #if BOTH(SPINDLE_FEATURE, LASER_FEATURE) + #error "Enable only one of SPINDLE_FEATURE or LASER_FEATURE." + #elif !PIN_EXISTS(SPINDLE_LASER_ENA) && DISABLED(SPINDLE_SERVO) + #error "(SPINDLE|LASER)_FEATURE requires SPINDLE_LASER_ENA_PIN or SPINDLE_SERVO to control the power." + #elif ENABLED(SPINDLE_CHANGE_DIR) && !PIN_EXISTS(SPINDLE_DIR) + #error "SPINDLE_DIR_PIN is required for SPINDLE_CHANGE_DIR." + #elif ENABLED(SPINDLE_LASER_PWM) + #if !defined(SPINDLE_LASER_PWM_PIN) || SPINDLE_LASER_PWM_PIN < 0 + #error "SPINDLE_LASER_PWM_PIN is required for SPINDLE_LASER_PWM." + #elif !_TEST_PWM(SPINDLE_LASER_PWM_PIN) + #error "SPINDLE_LASER_PWM_PIN not assigned to a PWM pin." + #elif !defined(SPINDLE_LASER_PWM_INVERT) + #error "SPINDLE_LASER_PWM_INVERT is required for (SPINDLE|LASER)_FEATURE." + #elif !(defined(SPEED_POWER_INTERCEPT) && defined(SPEED_POWER_MIN) && defined(SPEED_POWER_MAX) && defined(SPEED_POWER_STARTUP)) + #error "SPINDLE_LASER_PWM equation constant(s) missing." + #elif _PIN_CONFLICT(X_MIN) + #error "SPINDLE_LASER_PWM pin conflicts with X_MIN_PIN." + #elif _PIN_CONFLICT(X_MAX) + #error "SPINDLE_LASER_PWM pin conflicts with X_MAX_PIN." + #elif _PIN_CONFLICT(Z_STEP) + #error "SPINDLE_LASER_PWM pin conflicts with Z_STEP_PIN." + #elif _PIN_CONFLICT(CASE_LIGHT) + #error "SPINDLE_LASER_PWM_PIN conflicts with CASE_LIGHT_PIN." + #elif _PIN_CONFLICT(E0_AUTO_FAN) + #error "SPINDLE_LASER_PWM_PIN conflicts with E0_AUTO_FAN_PIN." + #elif _PIN_CONFLICT(E1_AUTO_FAN) + #error "SPINDLE_LASER_PWM_PIN conflicts with E1_AUTO_FAN_PIN." + #elif _PIN_CONFLICT(E2_AUTO_FAN) + #error "SPINDLE_LASER_PWM_PIN conflicts with E2_AUTO_FAN_PIN." + #elif _PIN_CONFLICT(E3_AUTO_FAN) + #error "SPINDLE_LASER_PWM_PIN conflicts with E3_AUTO_FAN_PIN." + #elif _PIN_CONFLICT(E4_AUTO_FAN) + #error "SPINDLE_LASER_PWM_PIN conflicts with E4_AUTO_FAN_PIN." + #elif _PIN_CONFLICT(E5_AUTO_FAN) + #error "SPINDLE_LASER_PWM_PIN conflicts with E5_AUTO_FAN_PIN." + #elif _PIN_CONFLICT(E6_AUTO_FAN) + #error "SPINDLE_LASER_PWM_PIN conflicts with E6_AUTO_FAN_PIN." + #elif _PIN_CONFLICT(E7_AUTO_FAN) + #error "SPINDLE_LASER_PWM_PIN conflicts with E7_AUTO_FAN_PIN." + #elif _PIN_CONFLICT(FAN) + #error "SPINDLE_LASER_PWM_PIN conflicts with FAN_PIN." + #elif _PIN_CONFLICT(FAN1) + #error "SPINDLE_LASER_PWM_PIN conflicts with FAN1_PIN." + #elif _PIN_CONFLICT(FAN2) + #error "SPINDLE_LASER_PWM_PIN conflicts with FAN2_PIN." + #elif _PIN_CONFLICT(FAN3) + #error "SPINDLE_LASER_PWM_PIN conflicts with FAN3_PIN." + #elif _PIN_CONFLICT(FAN4) + #error "SPINDLE_LASER_PWM_PIN conflicts with FAN4_PIN." + #elif _PIN_CONFLICT(FAN5) + #error "SPINDLE_LASER_PWM_PIN conflicts with FAN5_PIN." + #elif _PIN_CONFLICT(FAN6) + #error "SPINDLE_LASER_PWM_PIN conflicts with FAN6_PIN." + #elif _PIN_CONFLICT(FAN7) + #error "SPINDLE_LASER_PWM_PIN conflicts with FAN7_PIN." + #elif _PIN_CONFLICT(CONTROLLERFAN) + #error "SPINDLE_LASER_PWM_PIN conflicts with CONTROLLERFAN_PIN." + #elif _PIN_CONFLICT(MOTOR_CURRENT_PWM_XY) + #error "SPINDLE_LASER_PWM_PIN conflicts with MOTOR_CURRENT_PWM_XY." + #elif _PIN_CONFLICT(MOTOR_CURRENT_PWM_Z) + #error "SPINDLE_LASER_PWM_PIN conflicts with MOTOR_CURRENT_PWM_Z." + #elif _PIN_CONFLICT(MOTOR_CURRENT_PWM_E) + #error "SPINDLE_LASER_PWM_PIN conflicts with MOTOR_CURRENT_PWM_E." + #endif + #endif + #undef _PIN_CONFLICT +#endif + +#if NONE(HAS_MARLINUI_U8GLIB, EXTENSIBLE_UI) && ENABLED(PRINT_PROGRESS_SHOW_DECIMALS) + #error "PRINT_PROGRESS_SHOW_DECIMALS currently requires a Graphical LCD." +#endif + +#if HAS_ADC_BUTTONS && defined(ADC_BUTTON_DEBOUNCE_DELAY) && ADC_BUTTON_DEBOUNCE_DELAY < 16 + #error "ADC_BUTTON_DEBOUNCE_DELAY must be greater than 16." +#endif + +/** + * Check to make sure MONITOR_DRIVER_STATUS isn't enabled + * on boards where TMC drivers share the SPI bus with SD. + */ +#if HAS_TMC_SPI && ALL(MONITOR_DRIVER_STATUS, SDSUPPORT, USES_SHARED_SPI) + #error "MONITOR_DRIVER_STATUS and SDSUPPORT cannot be used together on boards with shared SPI." +#endif + +// G60/G61 Position Save +#if SAVED_POSITIONS > 256 + #error "SAVED_POSITIONS must be an integer from 0 to 256." +#endif + +/** + * Stepper Chunk support + */ +#if BOTH(DIRECT_STEPPING, LIN_ADVANCE) + #error "DIRECT_STEPPING is incompatible with LIN_ADVANCE. Enable in external planner if possible." +#endif + +/** + * Touch Buttons + */ +#if ENABLED(TOUCH_SCREEN) && DISABLED(TOUCH_SCREEN_CALIBRATION) + #ifndef TOUCH_CALIBRATION_X + #error "TOUCH_CALIBRATION_X must be defined with TOUCH_SCREEN." + #endif + #ifndef TOUCH_CALIBRATION_Y + #error "TOUCH_CALIBRATION_Y must be defined with TOUCH_SCREEN." + #endif + #ifndef TOUCH_OFFSET_X + #error "TOUCH_OFFSET_X must be defined with TOUCH_SCREEN." + #endif + #ifndef TOUCH_OFFSET_Y + #error "TOUCH_OFFSET_Y must be defined with TOUCH_SCREEN." + #endif +#endif + +/** + * Sanity check for WIFI + */ +#if EITHER(ESP3D_WIFISUPPORT, WIFISUPPORT) && DISABLED(ARDUINO_ARCH_ESP32) + #error "ESP3D_WIFISUPPORT or WIFISUPPORT requires an ESP32 MOTHERBOARD." +#endif + +/** + * Sanity Check for Password Feature + */ +#if ENABLED(PASSWORD_FEATURE) + #if NONE(HAS_LCD_MENU, PASSWORD_UNLOCK_GCODE, PASSWORD_CHANGE_GCODE) + #error "Without PASSWORD_UNLOCK_GCODE, PASSWORD_CHANGE_GCODE, or a supported LCD there's no way to unlock the printer or set a password." + #elif DISABLED(EEPROM_SETTINGS) + #warning "PASSWORD_FEATURE settings will be lost on power-off without EEPROM_SETTINGS." + #endif +#endif + + +/** + * Sanity Check for MEATPACK and BINARY_FILE_TRANSFER Features + */ +#if BOTH(MEATPACK, BINARY_FILE_TRANSFER) + #error "Either enable MEATPACK or enable BINARY_FILE_TRANSFER." +#endif + +/** + * Sanity check for valid stepper driver types + */ +#define _BAD_DRIVER(A) (defined(A##_DRIVER_TYPE) && !_DRIVER_ID(A##_DRIVER_TYPE)) +#if _BAD_DRIVER(X) + #error "X_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(Y) + #error "Y_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(Z) + #error "Z_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(X2) + #error "X2_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(Y2) + #error "Y2_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(Z2) + #error "Z2_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(Z3) + #error "Z3_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(Z4) + #error "Z4_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(E0) + #error "E0_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(E1) + #error "E1_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(E2) + #error "E2_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(E3) + #error "E3_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(E4) + #error "E4_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(E5) + #error "E5_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(E6) + #error "E6_DRIVER_TYPE is not recognized." +#endif +#if _BAD_DRIVER(E7) + #error "E7_DRIVER_TYPE is not recognized." +#endif +#undef _BAD_DRIVER + +// Misc. Cleanup +#undef _TEST_PWM |