diff options
Diffstat (limited to 'Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h')
| -rw-r--r-- | Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h | 182 |
1 files changed, 182 insertions, 0 deletions
diff --git a/Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h b/Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h new file mode 100644 index 0000000..5ac119f --- /dev/null +++ b/Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h @@ -0,0 +1,182 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * BIQU BQ111-A4 + * + * Applies to the following boards: + * + * BOARD_BIQU_BQ111_A4 (Hotend, Fan, Bed) + */ + +#if NOT_TARGET(MCU_LPC1768) + #error "Oops! Make sure you have the LPC1768 environment selected in your IDE." +#endif + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "BIQU Thunder B300 V1.0" +#endif + +// +// Limit Switches +// +#define X_MIN_PIN P1_24 // 10k pullup to 3.3V, 1K series +#define X_MAX_PIN P1_25 // 10k pullup to 3.3V, 1K series +#define Y_MIN_PIN P1_26 // 10k pullup to 3.3V, 1K series +#define Y_MAX_PIN P1_27 // 10k pullup to 3.3V, 1K series +#define Z_MIN_PIN P1_28 // 10k pullup to 3.3V, 1K series +#define Z_MAX_PIN P1_29 // 10k pullup to 3.3V, 1K series + +// +// Steppers +// +#define X_STEP_PIN P2_00 +#define X_DIR_PIN P0_05 +#define X_ENABLE_PIN P0_04 +#ifndef X_CS_PIN + #define X_CS_PIN P1_15 // ETH +#endif + +#define Y_STEP_PIN P2_01 +#define Y_DIR_PIN P0_11 +#define Y_ENABLE_PIN P0_10 +#ifndef Y_CS_PIN + #define Y_CS_PIN P1_14 // ETH +#endif + +#define Z_STEP_PIN P2_02 +#define Z_DIR_PIN P0_20 +#define Z_ENABLE_PIN P0_19 +#ifndef Z_CS_PIN + #define Z_CS_PIN P1_16 // ETH +#endif + +#define E0_STEP_PIN P2_03 +#define E0_DIR_PIN P0_22 +#define E0_ENABLE_PIN P0_21 +#ifndef E0_CS_PIN + #define E0_CS_PIN P1_17 // ETH +#endif + +// +// Software SPI pins for TMC2130 stepper drivers +// +#if ENABLED(TMC_USE_SW_SPI) + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI P0_18 // ETH + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO P0_17 // ETH + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK P0_15 // ETH + #endif +#endif + +// +// Temperature Sensors +// 3.3V max when defined as an analog input +// +#define TEMP_0_PIN P0_24_A1 // A0 (T0) +#define TEMP_BED_PIN P0_23_A0 // A1 (T1) + +// +// Heaters / Fans +// +#define HEATER_0_PIN P2_07 +#define HEATER_BED_PIN P2_05 +#ifndef FAN_PIN + #define FAN_PIN P2_04 +#endif + +// +// Unused +// +//#define PIN_P2_10 P2_10 // IBOOT-1 +//#define PIN_P0_27 P0_27 // Onboard SD Detect + +/** + * LCD / Controller + * + * REPRAP_DISCOUNT_SMART_CONTROLLER is not supported due to the lack of LCD_PINS_D5, + * LCD_PINS_D6 or LCD_PINS_D7 in the EXP1 connector. + * + * A remote SD card is not supported as the pins routed to EXP2 are the same as used + * for the onboard SD card, and a chip select signal is not provided for the remote + * SD card. + */ +#if HAS_WIRED_LCD + + #define BEEPER_PIN P1_31 // EXP1-1 + + #define BTN_EN1 P3_26 // EXP2-3 + #define BTN_EN2 P3_25 // EXP2-5 + #define BTN_ENC P1_30 // EXP1-2 + + #define SD_DETECT_PIN P0_27 // EXP2-7 + #define LCD_PINS_RS P0_16 // EXP1-4 + #define LCD_PINS_ENABLE P0_18 // (MOSI) EXP1-3 + #define LCD_PINS_D4 P0_15 // (SCK) EXP1-5 + + #if BOTH(HAS_MARLINUI_HD44780, IS_RRD_SC) + #error "REPRAP_DISCOUNT_SMART_CONTROLLER displays aren't supported by the BIQU B300 v1.0" + #endif + + #if ENABLED(SDSUPPORT) + #error "SDSUPPORT is not supported by the BIQU B300 v1.0 when an LCD controller is used" + #endif + +#endif // HAS_WIRED_LCD + +/** + * SD Card Reader + * + * Software SPI is used to interface with a stand-alone SD card reader connected to EXP1. + * Hardware SPI can't be used because P0_17 (MISO) is not brought out on this board. + */ +#if ENABLED(SDSUPPORT) + #define SD_SCK_PIN P0_15 // EXP1-5 + #define SD_MISO_PIN P0_16 // EXP1-4 + #define SD_MOSI_PIN P0_18 // EXP1-3 + #define SD_SS_PIN P1_30 // EXP1-2 + #define SDSS SD_SS_PIN +#endif + +/** + * PWMS + * + * There are 6 PWMS. Each PWM can be assigned to one of two pins. + * + * PWM1.1 P0_18 LCD_PINS_ENABLE + * PWM1.1 P2_0 X_STEP_PIN + * PWM1.2 P1_20 <none> + * PWM1.2 P2_1 Y_STEP_PIN + * PWM1.3 P1_21 <none> + * PWM1.3 P2_2 Z_STEP_PIN + * PWM1.4 P1_23 <none> + * PWM1.4 P2_3 E0_STEP_PIN + * PWM1.5 P1_24 X_MIN_PIN + * PWM1.5 P2_4 FAN_PIN + * PWM1.6 P1_26 Y_MIN_PIN + * PWM1.6 P2_5 HEATER_BED_PIN + */ |