diff options
Diffstat (limited to 'Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h')
| -rw-r--r-- | Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h | 168 |
1 files changed, 168 insertions, 0 deletions
diff --git a/Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h b/Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h new file mode 100644 index 0000000..1970c0c --- /dev/null +++ b/Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h @@ -0,0 +1,168 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +#if NOT_TARGET(MCU_LPC1768) + #error "Oops! Make sure you have the LPC1768 environment selected in your IDE." +#endif + +#define BOARD_INFO_NAME "GMARSH X6 REV1" + +// Ignore temp readings during develpment. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 + +// +// Enable 12MHz clock output on P1.27 pin to sync TMC2208 chip clocks +// +#define LPC1768_ENABLE_CLKOUT_12M + +// +// Servos +// +#define SERVO0_PIN P1_26 // PWM1[6] +#define SERVO1_PIN P1_18 // PWM1[1] + +// +// Limit Switches +// +#define X_MIN_PIN P0_00 +#define X_MAX_PIN P0_01 +#define Y_MIN_PIN P0_10 +#define Y_MAX_PIN P0_21 +#define Z_MIN_PIN P2_13 +#define Z_MAX_PIN P2_22 + +// +// Steppers +// + +#define X_STEP_PIN P1_01 +#define X_DIR_PIN P1_04 +#define X_ENABLE_PIN P0_26 + +#define Y_STEP_PIN P1_10 +#define Y_DIR_PIN P1_14 +#define Y_ENABLE_PIN P1_08 + +#define Z_STEP_PIN P1_17 +#define Z_DIR_PIN P4_29 +#define Z_ENABLE_PIN P1_15 + +#define E0_STEP_PIN P0_05 +#define E0_DIR_PIN P2_00 +#define E0_ENABLE_PIN P4_28 + +#define E1_STEP_PIN P2_03 +#define E1_DIR_PIN P2_04 +#define E1_ENABLE_PIN P2_01 + +#define E2_STEP_PIN P2_07 +#define E2_DIR_PIN P2_08 +#define E2_ENABLE_PIN P2_05 + +// +// TMC2208 UART pins +// +#if HAS_TMC_UART + #define X_SERIAL_TX_PIN P1_00 + #define X_SERIAL_RX_PIN P1_00 + #define Y_SERIAL_TX_PIN P1_09 + #define Y_SERIAL_RX_PIN P1_09 + #define Z_SERIAL_TX_PIN P1_16 + #define Z_SERIAL_RX_PIN P1_16 + #define E0_SERIAL_TX_PIN P0_04 + #define E0_SERIAL_RX_PIN P0_04 + #define E1_SERIAL_TX_PIN P2_02 + #define E1_SERIAL_RX_PIN P2_02 + #define E2_SERIAL_TX_PIN P2_06 + #define E2_SERIAL_RX_PIN P2_06 + + // Reduce baud rate to improve software serial reliability + #define TMC_BAUD_RATE 19200 +#else + #error "TMC2208 UART configuration is required for GMarsh X6." +#endif + +// +// Temperature Sensors +// 3.3V max when defined as an analog input +// +#define TEMP_0_PIN P0_24_A1 // AD0[0] on P0_23 +#define TEMP_BED_PIN P0_23_A0 // AD0[1] on P0_24 + +// +// Heaters / Fans +// +#define HEATER_BED_PIN P1_19 // Not a PWM pin, software PWM required +#define HEATER_0_PIN P3_26 // PWM1[3] +#define FAN_PIN P3_25 // Part cooling fan - connected to PWM1[2] +#define E0_AUTO_FAN_PIN P0_27 // Extruder cooling fan + +// +// Misc. Functions +// +#define LED_PIN P1_31 + +// +// LCD +// +#if IS_RRD_SC + #define BEEPER_PIN P0_19 + #define BTN_EN1 P1_23 + #define BTN_EN2 P1_24 + #define BTN_ENC P1_25 + #define LCD_PINS_RS P0_20 + #define LCD_PINS_ENABLE P0_21 + #define LCD_PINS_D4 P2_11 + #define LCD_PINS_D5 P0_22 + #define LCD_PINS_D6 P1_29 + #define LCD_PINS_D7 P1_28 + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + +#endif + +// +// SD Support +// + +#ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION LCD +#endif + +#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card + +#if SD_CONNECTION_IS(LCD) + #define SD_SCK_PIN P0_15 + #define SD_MISO_PIN P0_17 + #define SD_MOSI_PIN P0_18 + #define SD_SS_PIN P0_16 +#elif SD_CONNECTION_IS(ONBOARD) + #undef SD_DETECT_PIN + #define SD_DETECT_PIN P0_27 + #define SD_SCK_PIN P0_07 + #define SD_MISO_PIN P0_08 + #define SD_MOSI_PIN P0_09 + #define SD_SS_PIN ONBOARD_SD_CS_PIN +#endif |