diff options
Diffstat (limited to 'Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h')
| -rw-r--r-- | Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h | 219 |
1 files changed, 219 insertions, 0 deletions
diff --git a/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h b/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h new file mode 100644 index 0000000..fdd6487 --- /dev/null +++ b/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h @@ -0,0 +1,219 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Azteeg X5 MINI pin assignments + */ + +#if NOT_TARGET(MCU_LPC1769) + #error "Oops! Make sure you have the LPC1769 environment selected in your IDE." +#endif + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "Azteeg X5 MINI" +#endif +#define BOARD_WEBSITE_URL "tiny.cc/x5_mini" + +// +// LED +// +#define LED_PIN P1_18 +#define LED2_PIN P1_20 +#define LED3_PIN P1_19 +#define LED4_PIN P1_21 + +// +// Servos +// +#define SERVO0_PIN P1_29 + +// +// Limit Switches +// +#define X_STOP_PIN P1_24 +#define Y_STOP_PIN P1_26 +#define Z_STOP_PIN P1_28 + +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN P2_04 +#endif + +#ifndef FILWIDTH_PIN + #define FILWIDTH_PIN P0_25_A2 // Analog Input (P0_25) +#endif + +// +// Steppers +// +#define X_STEP_PIN P2_01 +#define X_DIR_PIN P0_11 +#define X_ENABLE_PIN P0_10 + +#define Y_STEP_PIN P2_02 +#define Y_DIR_PIN P0_20 +#define Y_ENABLE_PIN P0_19 + +#define Z_STEP_PIN P2_03 +#define Z_DIR_PIN P0_22 +#define Z_ENABLE_PIN P0_21 + +#define E0_STEP_PIN P2_00 +#define E0_DIR_PIN P0_05 +#define E0_ENABLE_PIN P0_04 + +// +// DIGIPOT slave addresses (7-bit unshifted) +// +#ifndef DIGIPOT_I2C_ADDRESS_A + #define DIGIPOT_I2C_ADDRESS_A 0x2C +#endif +#ifndef DIGIPOT_I2C_ADDRESS_B + #define DIGIPOT_I2C_ADDRESS_B 0x2E +#endif + +// +// Temperature Sensors +// 3.3V max when defined as an analog input +// +#define TEMP_BED_PIN P0_23_A0 // A0 (TH1) +#define TEMP_0_PIN P0_24_A1 // A1 (TH2) + +// +// Heaters / Fans +// +#define HEATER_BED_PIN P2_07 +#define HEATER_0_PIN P2_05 +#ifndef FAN_PIN + #define FAN_PIN P0_26 +#endif +#define FAN1_PIN P1_25 + +// +// Display +// +#if HAS_WIRED_LCD + + #if ENABLED(CR10_STOCKDISPLAY) + + // Re-Arm can support Creality stock display without SD card reader and single cable on EXP3. + // Re-Arm J3 pins 1 (p1.31) & 2 (P3.26) are not used. Stock cable will need to have one + // 10-pin IDC connector trimmed or replaced with a 12-pin IDC connector to fit J3. + // Requires REVERSE_ENCODER_DIRECTION in Configuration.h + + #define BEEPER_PIN P2_11 // J3-3 & AUX-4 + + #define BTN_EN1 P0_16 // J3-7 & AUX-4 + #define BTN_EN2 P1_23 // J3-5 & AUX-4 + #define BTN_ENC P3_25 // J3-4 & AUX-4 + + #define LCD_PINS_RS P0_15 // J3-9 & AUX-4 (CS) + #define LCD_PINS_ENABLE P0_18 // J3-10 & AUX-3 (SID, MOSI) + #define LCD_PINS_D4 P2_06 // J3-8 & AUX-3 (SCK, CLK) + + #else + + #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4 + #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 + #define BTN_ENC P2_11 // (35) J3-3 & AUX-4 + + #define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3 + #define KILL_PIN P1_22 // (41) J5-4 & AUX-4 + #define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4 + #define LCD_SDSS P0_16 // (16) J3-7 & AUX-4 + #define LCD_BACKLIGHT_PIN P0_16 // (16) J3-7 & AUX-4 - only used on DOGLCD controllers + #define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3 + #define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3 + + #define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2 + + #if IS_RRW_KEYPAD + #define SHIFT_OUT_PIN P0_18 // (51) (MOSI) J3-10 & AUX-3 + #define SHIFT_CLK_PIN P0_15 // (52) (SCK) J3-9 & AUX-3 + #define SHIFT_LD_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3 + #elif !IS_NEWPANEL + //#define SHIFT_OUT_PIN P2_11 // (35) J3-3 & AUX-4 + //#define SHIFT_CLK_PIN P3_26 // (31) J3-2 & AUX-4 + //#define SHIFT_LD_PIN P3_25 // (33) J3-4 & AUX-4 + //#define SHIFT_EN_PIN P1_22 // (41) J5-4 & AUX-4 + #endif + + #if ANY(VIKI2, miniVIKI) + //#define LCD_SCREEN_ROT_180 + + #define BEEPER_PIN P1_30 // (37) may change if cable changes + #define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2 + #define DOGLCD_SCK SD_SCK_PIN + #define DOGLCD_MOSI SD_MOSI_PIN + + #define STAT_LED_BLUE_PIN P0_26 // (63) may change if cable changes + #define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes + #else + #if IS_ULTIPANEL + #define LCD_PINS_D5 P1_17 // (71) ENET_MDIO + #define LCD_PINS_D6 P1_14 // (73) ENET_RX_ER + #define LCD_PINS_D7 P1_10 // (75) ENET_RXD1 + #endif + #define BEEPER_PIN P1_30 // (37) not 5V tolerant + #define DOGLCD_CS P0_16 // (16) + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + + #endif + + #if ENABLED(MINIPANEL) + // GLCD features + // Uncomment screen orientation + //#define LCD_SCREEN_ROT_90 + //#define LCD_SCREEN_ROT_180 + //#define LCD_SCREEN_ROT_270 + #endif + + #endif + +#endif // HAS_WIRED_LCD + +// +// SD Support +// +#ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION ONBOARD +#endif + +#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card + +#if SD_CONNECTION_IS(LCD) + #define SD_SCK_PIN P0_15 + #define SD_MISO_PIN P0_17 + #define SD_MOSI_PIN P0_18 + #define SD_SS_PIN P1_23 +#elif SD_CONNECTION_IS(ONBOARD) + #undef SD_DETECT_PIN + #define SD_SCK_PIN P0_07 + #define SD_MISO_PIN P0_08 + #define SD_MOSI_PIN P0_09 + #define SD_SS_PIN ONBOARD_SD_CS_PIN +#elif SD_CONNECTION_IS(CUSTOM_CABLE) + #error "No custom SD drive cable defined for this board." +#endif |