diff options
Diffstat (limited to 'Marlin/src/pins/lpc1769/pins_COHESION3D_REMIX.h')
| -rw-r--r-- | Marlin/src/pins/lpc1769/pins_COHESION3D_REMIX.h | 289 |
1 files changed, 289 insertions, 0 deletions
diff --git a/Marlin/src/pins/lpc1769/pins_COHESION3D_REMIX.h b/Marlin/src/pins/lpc1769/pins_COHESION3D_REMIX.h new file mode 100644 index 0000000..edf13ce --- /dev/null +++ b/Marlin/src/pins/lpc1769/pins_COHESION3D_REMIX.h @@ -0,0 +1,289 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Cohesion3D ReMix pin assignments + */ + +#if NOT_TARGET(MCU_LPC1769) + #error "Oops! Make sure you have the LPC1769 environment selected in your IDE." +#endif + +#define BOARD_INFO_NAME "Cohesion3D ReMix" + +// +// Servos +// +#define SERVO0_PIN P2_04 + +// +// Limit Switches +// +#define X_MIN_PIN P1_24 // 10k pullup to 3.3V +#define X_MAX_PIN P1_25 // 10k pullup to 3.3V +#define Y_MIN_PIN P1_26 // 10k pullup to 3.3V +#define Y_MAX_PIN P1_27 // 10k pullup to 3.3V +#define Z_MIN_PIN P1_28 // 10k pullup to 3.3V +#define Z_MAX_PIN P1_29 // 10k pullup to 3.3V + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN P1_29 +#endif + +// +// Steppers +// +#define X_STEP_PIN P2_00 +#define X_DIR_PIN P0_05 +#define X_ENABLE_PIN P0_04 +#define X_CS_PIN P1_10 // Ethernet Expansion - Pin 9 + +#define Y_STEP_PIN P2_01 +#define Y_DIR_PIN P0_11 +#define Y_ENABLE_PIN P0_10 +#define Y_CS_PIN P1_09 // Ethernet Expansion - Pin 10 + +#define Z_STEP_PIN P2_02 +#define Z_DIR_PIN P0_20 +#define Z_ENABLE_PIN P0_19 +#define Z_CS_PIN P1_00 // Ethernet Expansion - Pin 11 + +#define E0_STEP_PIN P2_03 +#define E0_DIR_PIN P0_22 +#define E0_ENABLE_PIN P0_21 +#define E0_CS_PIN P1_04 // Ethernet Expansion - Pin 12 + +#define E1_STEP_PIN P2_08 +#define E1_DIR_PIN P2_13 +#define E1_ENABLE_PIN P4_29 +#define E1_CS_PIN P1_01 // Ethernet Expansion - Pin 14 + +#define E2_STEP_PIN P1_20 +#define E2_DIR_PIN P1_19 +#define E2_ENABLE_PIN P1_21 +#define E2_CS_PIN P1_18 // FET 6 + +// +// Default pins for TMC software SPI +// +#if ENABLED(TMC_USE_SW_SPI) + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI P1_16 // Ethernet Expansion - Pin 5 + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO P1_17 // Ethernet Expansion - Pin 6 + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK P1_08 // Ethernet Expansion - Pin 7 + #endif +#endif + +// +// Analog Inputs +// 3.3V max when defined as an analog input +// +#define TEMP_0_PIN P0_23_A0 +#define TEMP_BED_PIN P0_24_A1 +#define TEMP_1_PIN P0_25_A2 +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILWIDTH_PIN P0_26_A3 +#else + #define TEMP_2_PIN P0_26_A3 +#endif + +// +// Heaters / Fans +// +#define HEATER_BED_PIN P2_05 +#define HEATER_0_PIN P2_07 // FET 1 +#define HEATER_1_PIN P1_23 // FET 2 +#define HEATER_2_PIN P1_22 // FET 3 +#ifndef FAN_PIN + #define FAN_PIN P2_06 // FET 4 +#endif + +// +// Auto fans +// +#if HOTENDS == 3 + #define AUTO_FAN_PIN P1_18 // FET 6 +#else + #define AUTO_FAN_PIN P1_22 // FET 3 +#endif +#ifndef E0_AUTO_FAN_PIN + #define E0_AUTO_FAN_PIN AUTO_FAN_PIN +#endif +#ifndef E1_AUTO_FAN_PIN + #define E1_AUTO_FAN_PIN AUTO_FAN_PIN +#endif +#ifndef E2_AUTO_FAN_PIN + #define E2_AUTO_FAN_PIN AUTO_FAN_PIN +#endif + +// +// Misc. Functions +// +#define LED_PIN P4_28 // Play LED + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if HAS_CUTTER + #undef HEATER_0_PIN + #undef HEATER_BED_PIN + #undef FAN_PIN + #define SPINDLE_LASER_ENA_PIN P2_07 // FET 1 + #define SPINDLE_LASER_PWM_PIN P2_05 // Bed FET + #define SPINDLE_DIR_PIN P2_06 // FET 4 +#endif + +// +// LCD / Controller +// +// LCD_PINS_D5, D6, and D7 are not present in the EXP1 connector, and will need to be +// defined to use the REPRAP_DISCOUNT_SMART_CONTROLLER. +// +// A remote SD card is currently not supported because the pins routed to the EXP2 +// connector are shared with the onboard SD card, and Marlin does not support that +// hardware configuration. +// + +#if ENABLED(FYSETC_MINI_12864) + + #define FORCE_SOFT_SPI // REQUIRED - results in LCD soft SPI mode 3 + + #define BEEPER_PIN P1_31 // EXP1-1 + #define BTN_ENC P1_30 // EXP1-2 + #define DOGLCD_CS P0_18 // EXP1-3 + #define DOGLCD_A0 P0_16 // EXP1-4 + #define LCD_RESET_PIN P0_15 // EXP1-5 + + // A custom cable is REQUIRED for EXP2 cable because the SCK & MOSI on the card's EXP2 are dedicated + // to the onboard SD card. All required EXP2 signals come from the Ethernet connector. Pin 1 of this + // connector is the one nearest the motor power connector. + #define DOGLCD_SCK P1_17 // EXP2-2 => Ethernet pin 5 (bottom, 3 from left) + #define BTN_EN2 P1_09 // EXP2-3 => Ethernet pin 9 (bottom, 5 from left) + #define BTN_EN1 P1_04 // EXP2-5 => Ethernet pin 11 (bottom, 6 from left) + #define DOGLCD_MOSI P1_01 // EXP2-6 => Ethernet pin 13 (bottom, 7 from left) + + // A custom EXP1 cable is required colored LEDs. Pins 1-5, 9, 10 of the cable go to pins 1-5, 9, 10 + // on the board's EXP1 connector. Pins 6, 7, and 8 of the EXP1 cable go to the Ethernet connector. + // Rev 1.2 displays do NOT require the RGB LEDs. 2.0 and 2.1 displays do require RGB. + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN P1_16 // EXP1-6 => Ethernet pin 6 (top row, 3 from left) + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN P1_10 // EXP1-7 => Ethernet pin 10 (top row, 5 from left) + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN P1_00 // EXP1-8 => Ethernet pin 12 (top row, 6 from left) + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #define NEOPIXEL_PIN P1_16 // EXP1-6 => Ethernet pin 6 (top row, 3 from left) + #endif + +#elif HAS_WIRED_LCD + + #define BEEPER_PIN P1_31 // EXP1-1 + //#define SD_DETECT_PIN P0_27 // EXP2-7 + + #define BTN_EN1 P3_26 // EXP2-5 + #define BTN_EN2 P3_25 // EXP2-3 + #define BTN_ENC P1_30 // EXP1-2 + + #define LCD_PINS_RS P0_16 // EXP1-4 + #define LCD_SDSS P0_28 // EXP2-4 + #define LCD_PINS_ENABLE P0_18 // EXP1-3 + #define LCD_PINS_D4 P0_15 // EXP1-5 + + #define KILL_PIN P2_11 // EXP2-10 + +#endif // HAS_WIRED_LCD + +// +// SD Support +// +#ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION ONBOARD +#endif + +#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card + +#if SD_CONNECTION_IS(LCD) || SD_CONNECTION_IS(ONBOARD) + #define SD_SCK_PIN P0_07 // (52) system defined J3-9 & AUX-3 + #define SD_MISO_PIN P0_08 // (50) system defined J3-10 & AUX-3 + #define SD_MOSI_PIN P0_09 // (51) system defined J3-10 & AUX-3 + #if SD_CONNECTION_IS(LCD) + #define SD_SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS) - CS used by Marlin + #else + #undef SD_DETECT_PIN + #define SD_SS_PIN ONBOARD_SD_CS_PIN + #endif +#elif SD_CONNECTION_IS(CUSTOM_CABLE) + #error "No custom SD drive cable defined for this board." +#endif + +// +// Ethernet pins +// +//#define ENET_MDIO P1_17 // Ethernet pin 5 (bottom, 3 from left) +//#define ENET_RX_ER P1_14 +//#define ENET_RXD1 P1_10 // Ethernet pin 10 (top row, 5 from left) +//#define ENET_MOC P1_16 // Ethernet pin 6 (top row, 3 from left) +//#define REF_CLK P1_15 +//#define ENET_RXD0 P1_09 // Ethernet pin 9 (bottom, 5 from left) +//#define ENET_CRS P1_08 // Ethernet pin 8 (top row, 4 from left) - INPUT ONLY +//#define ENET_TX_EN P1_04 // Ethernet pin 11 (bottom, 6 from left) +//#define ENET_TXD0 P1_00 // Ethernet pin 12 (top row, 6 from left) +//#define ENET_TXD1 P1_01 // Ethernet pin 13 (bottom, 7 from left) + +/** + * EXP1 pins + * 1 - P1_31 + * 2 - P1_30 + * 3 - P0_18 + * 4 - P0_16 + * 5 - P0_15 + * 6 - N/C + * 7 - N/C + * 8 - P0_27 (also on EXP2-7) + * 9 - GND + * 10 - +5V + * + * + * EXP2 pins + * 1 - P0_08 + * 2 - P0_07 + * 3 - P3_26 + * 4 - P0_28 + * 5 - P3_25 + * 6 - P0_09 + * 7 - P0_27 (also on EXP1_8) + * 8 - P2_11 + * 9 - GND + * 10 - N/C + */ |