diff options
Diffstat (limited to 'Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h')
| -rw-r--r-- | Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h | 182 |
1 files changed, 182 insertions, 0 deletions
diff --git a/Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h b/Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h new file mode 100644 index 0000000..d4f3e5b --- /dev/null +++ b/Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h @@ -0,0 +1,182 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * TH3D EZBoard pin assignments + */ + +#if NOT_TARGET(MCU_LPC1769) + #error "Oops! Make sure you have the LPC1769 environment selected in your IDE." +#endif + +#define BOARD_INFO_NAME "TH3D EZBoard" +#define BOARD_WEBSITE_URL "th3dstudio.com" + +// +// Servos +// +#define SERVO0_PIN P2_04 + +// +// Limit Switches +// +#define X_STOP_PIN P1_24 +#define Y_STOP_PIN P1_25 +#define Z_STOP_PIN P1_26 + +// +// Filament Runout Sensor +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN P1_27 +#endif + +// +// Steppers +// +#define X_STEP_PIN P2_00 +#define X_DIR_PIN P1_16 +#define X_ENABLE_PIN P1_17 + +#define Y_STEP_PIN P2_01 +#define Y_DIR_PIN P1_10 +#define Y_ENABLE_PIN P1_09 + +#define Z_STEP_PIN P2_02 +#define Z_DIR_PIN P1_15 +#define Z_ENABLE_PIN P1_14 + +#define E0_STEP_PIN P2_03 +#define E0_DIR_PIN P1_04 +#define E0_ENABLE_PIN P1_08 + +#define E1_STEP_PIN P2_08 +#define E1_DIR_PIN P2_13 +#define E1_ENABLE_PIN P4_29 + +#if HAS_TMC_UART + // + // TMC220x stepper drivers + // Software serial + // + #define X_SERIAL_TX_PIN P0_04 + #define X_SERIAL_RX_PIN P0_05 + #define Y_SERIAL_TX_PIN P0_10 + #define Y_SERIAL_RX_PIN P0_11 + #define Z_SERIAL_TX_PIN P0_19 + #define Z_SERIAL_RX_PIN P0_20 + #define E0_SERIAL_TX_PIN P0_22 + #define E0_SERIAL_RX_PIN P0_21 + + // Reduce baud rate to improve software serial reliability + #define TMC_BAUD_RATE 19200 +#endif + +// +// Temp Sensors +// 3.3V max when defined as an Analog Input! +// +#if TEMP_SENSOR_0 == 20 // PT100 Adapter + #define TEMP_0_PIN P0_02_A7 // Analog Input +#else + #define TEMP_0_PIN P0_23_A0 // Analog Input P0_23 +#endif + +#define TEMP_BED_PIN P0_24_A1 // Analog Input P0_24 +#define TEMP_1_PIN P0_25_A2 // Analog Input P0_25 + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILWIDTH_PIN P0_26_A3 // Analog Input P0_26 +#else + #define TEMP_2_PIN P0_26_A3 // Analog Input P0_26 +#endif + +// +// Heaters / Fans +// +#define HEATER_BED_PIN P2_05 +#define HEATER_0_PIN P2_07 +#ifndef FAN_PIN + #define FAN_PIN P2_06 +#endif +#define FAN1_PIN P1_22 + +// +// Auto fans +// +#define AUTO_FAN_PIN P1_22 // FET 3 +#ifndef E0_AUTO_FAN_PIN + #define E0_AUTO_FAN_PIN AUTO_FAN_PIN +#endif +#ifndef E1_AUTO_FAN_PIN + #define E1_AUTO_FAN_PIN AUTO_FAN_PIN +#endif +#ifndef E2_AUTO_FAN_PIN + #define E2_AUTO_FAN_PIN AUTO_FAN_PIN +#endif + +// +// SD Card +// + +#define SDCARD_CONNECTION ONBOARD + +#define SD_SCK_PIN P0_07 +#define SD_MISO_PIN P0_08 +#define SD_MOSI_PIN P0_09 +#define ONBOARD_SD_CS_PIN P0_06 +#define SD_SS_PIN ONBOARD_SD_CS_PIN + +// +// LCD / Controller +// + +/** + * _____ + * 5V | · · | GND + * (LCD_EN) P0_18 | · · | P0_16 (LCD_RS) + * (LCD_D4) P0_15 | · · P3_25 (BTN_EN2) + * (RESET) P2_11 | · · | P3_26 (BTN_EN1) + * (BTN_ENC) P1_30 | · · | P1_31 (BEEPER) + * ----- + * EXP1 + * + * LCD_PINS_D5, D6, and D7 are not present in the EXP1 connector, and will need to be + * defined to use the REPRAP_DISCOUNT_SMART_CONTROLLER. + * + * A remote SD card is currently not supported because the pins routed to the EXP2 + * connector are shared with the onboard SD card. + */ + +#if ENABLED(CR10_STOCKDISPLAY) + #define BEEPER_PIN P1_31 + #define BTN_EN1 P3_26 + #define BTN_EN2 P3_25 + #define BTN_ENC P1_30 + #define LCD_PINS_RS P0_16 + #define LCD_PINS_ENABLE P0_18 + #define LCD_PINS_D4 P0_15 + #define KILL_PIN P2_11 +#elif HAS_WIRED_LCD + #error "Only the CR10_STOCKDISPLAY is supported with TH3D EZBoard." +#endif |