diff options
Diffstat (limited to 'Marlin/src/pins/mega/pins_GT2560_V3.h')
| -rw-r--r-- | Marlin/src/pins/mega/pins_GT2560_V3.h | 185 |
1 files changed, 185 insertions, 0 deletions
diff --git a/Marlin/src/pins/mega/pins_GT2560_V3.h b/Marlin/src/pins/mega/pins_GT2560_V3.h new file mode 100644 index 0000000..606debd --- /dev/null +++ b/Marlin/src/pins/mega/pins_GT2560_V3.h @@ -0,0 +1,185 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * GT2560 RevB + GT2560 V3.0 + GT2560 V3.1 + GT2560 V4.0 pin assignment + */ + +#if NOT_TARGET(__AVR_ATmega1280__, __AVR_ATmega2560__) + #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#endif + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "GT2560 V3.0" +#endif + +// +// Servos +// +#define SERVO0_PIN 11 //13 untested 3Dtouch + +// +// Limit Switches +// +#ifndef X_STOP_PIN + #ifndef X_MIN_PIN + #define X_MIN_PIN 24 + #endif + #ifndef X_MAX_PIN + #define X_MAX_PIN 22 + #endif +#endif +#ifndef Y_STOP_PIN + #ifndef Y_MIN_PIN + #define Y_MIN_PIN 28 + #endif + #ifndef Y_MAX_PIN + #define Y_MAX_PIN 26 + #endif +#endif +#ifndef Z_STOP_PIN + #ifndef Z_MIN_PIN + #define Z_MIN_PIN 30 + #endif + #ifndef Z_MAX_PIN + #define Z_MAX_PIN 32 + #endif +#endif + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 32 +#endif + +// +// Runout Sensor +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN 66 +#endif +#ifndef FIL_RUNOUT2_PIN + #define FIL_RUNOUT2_PIN 67 +#endif + +// +// Power Recovery +// +#define POWER_LOSS_PIN 69 // Pin to detect power loss +#define POWER_LOSS_STATE LOW + +// +// Steppers +// +#define X_STEP_PIN 37 +#define X_DIR_PIN 39 +#define X_ENABLE_PIN 35 + +#define Y_STEP_PIN 31 +#define Y_DIR_PIN 33 +#define Y_ENABLE_PIN 29 + +#define Z_STEP_PIN 25 +#define Z_DIR_PIN 23 +#define Z_ENABLE_PIN 27 + +#define E0_STEP_PIN 46 +#define E0_DIR_PIN 44 +#define E0_ENABLE_PIN 12 + +#define E1_STEP_PIN 49 +#define E1_DIR_PIN 47 +#define E1_ENABLE_PIN 48 + +#define E2_STEP_PIN 43 +#define E2_DIR_PIN 45 +#define E2_ENABLE_PIN 41 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 11 // Analog Input +#define TEMP_1_PIN 9 // Analog Input +#define TEMP_2_PIN 8 // Analog Input +#define TEMP_BED_PIN 10 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 10 +#define HEATER_1_PIN 3 +#define HEATER_2_PIN 2 +#define HEATER_BED_PIN 4 +#define FAN_PIN 9 +#define FAN1_PIN 8 +#define FAN2_PIN 7 + +// +// Misc. Functions +// +#define SD_DETECT_PIN 38 +#define SDSS 53 +#define LED_PIN 13 // Use 6 (case light) for external LED. 13 is internal (yellow) LED. +#define PS_ON_PIN 12 +#define SUICIDE_PIN 54 // This pin must be enabled at boot to keep power flowing + +#ifndef CASE_LIGHT_PIN + #define CASE_LIGHT_PIN 6 // 21 +#endif + +// +// LCD Controller +// +#define BEEPER_PIN 18 + +#ifndef LCD_PINS_RS + #define LCD_PINS_RS 20 +#endif +#ifndef LCD_PINS_ENABLE + #define LCD_PINS_ENABLE 17 +#endif +#ifndef LCD_PINS_D4 + #define LCD_PINS_D4 16 +#endif +#ifndef LCD_PINS_D5 + #define LCD_PINS_D5 21 +#endif +#ifndef LCD_PINS_D6 + #define LCD_PINS_D6 5 +#endif +#ifndef LCD_PINS_D7 + #define LCD_PINS_D7 36 +#endif + +#if IS_NEWPANEL + #ifndef BTN_EN1 + #define BTN_EN1 42 + #endif + #ifndef BTN_EN2 + #define BTN_EN2 40 + #endif + #ifndef BTN_ENC + #define BTN_ENC 19 + #endif +#endif |