diff options
Diffstat (limited to 'Marlin/src/pins/mega/pins_PICA.h')
| -rw-r--r-- | Marlin/src/pins/mega/pins_PICA.h | 153 |
1 files changed, 153 insertions, 0 deletions
diff --git a/Marlin/src/pins/mega/pins_PICA.h b/Marlin/src/pins/mega/pins_PICA.h new file mode 100644 index 0000000..ff4d3e8 --- /dev/null +++ b/Marlin/src/pins/mega/pins_PICA.h @@ -0,0 +1,153 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ + +/** + * Arduino Mega with PICA pin assignments + * + * PICA is Power, Interface, and Control Adapter and is open source hardware. + * See https://github.com/mjrice/PICA for schematics etc. + * + * Applies to PICA, PICA_REVB + */ + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "PICA" +#endif + +/* +// Note that these are the "pins" that correspond to the analog inputs on the arduino mega. +// These are not the same as the physical pin numbers + AD0 = 54; AD1 = 55; AD2 = 56; AD3 = 57; + AD4 = 58; AD5 = 59; AD6 = 60; AD7 = 61; + AD8 = 62; AD9 = 63; AD10 = 64; AD11 = 65; + AD12 = 66; AD13 = 67; AD14 = 68; AD15 = 69; +*/ + +#if NOT_TARGET(__AVR_ATmega1280__, __AVR_ATmega2560__) + #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." +#endif + +// +// Servos +// +#define SERVO0_PIN 3 +#define SERVO1_PIN 4 +#define SERVO2_PIN 5 +// +// Limit Switches +// +#define X_MIN_PIN 14 +#define X_MAX_PIN 15 +#define Y_MIN_PIN 16 +#define Y_MAX_PIN 17 +#define Z_MIN_PIN 23 +#define Z_MAX_PIN 22 + +// +// Steppers +// +#define X_STEP_PIN 55 +#define X_DIR_PIN 54 +#define X_ENABLE_PIN 60 + +#define Y_STEP_PIN 57 +#define Y_DIR_PIN 56 +#define Y_ENABLE_PIN 61 + +#define Z_STEP_PIN 59 +#define Z_DIR_PIN 58 +#define Z_ENABLE_PIN 62 + +#define E0_STEP_PIN 67 +#define E0_DIR_PIN 24 +#define E0_ENABLE_PIN 26 + +#define E1_STEP_PIN 68 +#define E1_DIR_PIN 28 +#define E1_ENABLE_PIN 27 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 9 // Analog Input +#define TEMP_1_PIN 10 +#define TEMP_BED_PIN 10 +#define TEMP_2_PIN 11 +#define TEMP_3_PIN 12 + +// +// Heaters / Fans +// +#ifndef HEATER_0_PIN + #define HEATER_0_PIN 10 // E0 +#endif +#ifndef HEATER_1_PIN + #define HEATER_1_PIN 2 // E1 +#endif +#define HEATER_BED_PIN 8 // HEAT-BED + +#ifndef FAN_PIN + #define FAN_PIN 9 +#endif +#ifndef FAN_2_PIN + #define FAN_2_PIN 7 +#endif + +#define SDPOWER_PIN -1 +#define LED_PIN -1 +#define PS_ON_PIN -1 +#define KILL_PIN -1 + +#define SSR_PIN 6 + +// SPI for Max6675 or Max31855 Thermocouple +#if DISABLED(SDSUPPORT) + #define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card +#else + #define MAX6675_SS_PIN 66 // Don't use 49 (SD_DETECT_PIN) +#endif + +// +// SD Support +// +#define SD_DETECT_PIN 49 +#define SDSS 53 + +// +// LCD / Controller +// +#define BEEPER_PIN 29 + +#if HAS_WIRED_LCD + #define LCD_PINS_RS 33 + #define LCD_PINS_ENABLE 30 + #define LCD_PINS_D4 35 + #define LCD_PINS_D5 32 + #define LCD_PINS_D6 37 + #define LCD_PINS_D7 36 + + #define BTN_EN1 47 + #define BTN_EN2 48 + #define BTN_ENC 31 + + #define LCD_SDSS 53 +#endif |