diff options
Diffstat (limited to 'Marlin/src/pins/sam/pins_RAMPS_SMART.h')
| -rw-r--r-- | Marlin/src/pins/sam/pins_RAMPS_SMART.h | 110 |
1 files changed, 110 insertions, 0 deletions
diff --git a/Marlin/src/pins/sam/pins_RAMPS_SMART.h b/Marlin/src/pins/sam/pins_RAMPS_SMART.h new file mode 100644 index 0000000..9b76ee2 --- /dev/null +++ b/Marlin/src/pins/sam/pins_RAMPS_SMART.h @@ -0,0 +1,110 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Arduino Due with RAMPS-SMART pin assignments + * + * Applies to the following boards: + * + * RAMPS_SMART_EFB (Hotend, Fan, Bed) + * RAMPS_SMART_EEB (Hotend0, Hotend1, Bed) + * RAMPS_SMART_EFF (Hotend, Fan0, Fan1) + * RAMPS_SMART_EEF (Hotend0, Hotend1, Fan) + * RAMPS_SMART_SF (Spindle, Controller Fan) + * + * Differences between + * RAMPS_14 | RAMPS-SMART + * NONE | D16 (Additional AUX-3 pin(AUX3_2PIN), shares the same pin with AUX4_18PIN) + * NONE | D17 (Additional AUX-3 pin(AUX3_1PIN), shares the same pin with AUX4_17PIN) + * D0 | NONE + * D1 | NONE + * A3/D57 | NONE + * A4/D58 | NONE + * A5/D59 | A3/D57 + * A9/D63 | A4/D58 + * A10/D64 | A5/D59 + * A11/D65 | D66 + * A12/D66 | D67 + * A13 | A9 + * A14 | A10 + * A15 | A11 + * + * + * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER works fine connected to AUX-4 with + * Smart Adapter, but requires removing the AUX3 pin header on the adapter to fit. + * To use the SD card reader, wire its pins to AUX-3 (and use Software SPI). + * + * To use Hardware SPI for SD, the SDSS pin must be set to 52 instead of 53. + * Hardware SPI also requires additional wiring because the board doesn't pass + * the 6-pin SPI header from the DUE board. + * (Search the web for "Arduino DUE Board Pinout" to see the correct header.) + */ + +#if NOT_TARGET(__SAM3X8E__) + #error "Oops! Select 'Arduino Due' in 'Tools > Board.'" +#endif + +#define BOARD_INFO_NAME "RAMPS-SMART" +#define IS_RAMPS_SMART +#include "../ramps/pins_RAMPS.h" + +// I2C EEPROM with 4K of space +#define I2C_EEPROM +#define MARLIN_EEPROM_SIZE 0x1000 + +#define RESET_PIN 42 // Resets the board if the jumper is attached + +// +// Temperature Sensors +// +#undef TEMP_0_PIN +#define TEMP_0_PIN 9 // Analog Input + +#undef TEMP_1_PIN +#define TEMP_1_PIN 10 // Analog Input + +#undef TEMP_BED_PIN +#define TEMP_BED_PIN 11 // Analog Input + +// SPI for Max6675 or Max31855 Thermocouple +#undef MAX6675_SS_PIN +#if DISABLED(SDSUPPORT) + #define MAX6675_SS_PIN 67 // Don't use 53 if using Display/SD card +#else + #define MAX6675_SS_PIN 67 // Don't use 49 (SD_DETECT_PIN) +#endif + +// +// LCD / Controller +// +// Support for AZSMZ 12864 LCD with SD Card 3D printer smart controller control panel +#if ENABLED(AZSMZ_12864) + #define BEEPER_PIN 66 // Smart RAMPS 1.42 pinout diagram on RepRap WIKI erroneously says this should be pin 65 + #define DOGLCD_A0 59 + #define DOGLCD_CS 44 + #define BTN_EN1 58 + #define BTN_EN2 40 + #define BTN_ENC 67 // Smart RAMPS 1.42 pinout diagram on RepRap WIKI erroneously says this should be pin 66 + #define SD_DETECT_PIN 49 // Pin 49 for display sd interface, 72 for easy adapter board + #define KILL_PIN 42 +#endif |