diff options
Diffstat (limited to 'Marlin/src/pins/sam/pins_RURAMPS4D_11.h')
| -rw-r--r-- | Marlin/src/pins/sam/pins_RURAMPS4D_11.h | 278 |
1 files changed, 278 insertions, 0 deletions
diff --git a/Marlin/src/pins/sam/pins_RURAMPS4D_11.h b/Marlin/src/pins/sam/pins_RURAMPS4D_11.h new file mode 100644 index 0000000..6a28340 --- /dev/null +++ b/Marlin/src/pins/sam/pins_RURAMPS4D_11.h @@ -0,0 +1,278 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + * Ported sys0724 & Vynt + */ + +/** + * Arduino Mega? or Due with RuRAMPS4DUE pin assignments + * + * Applies to the following boards: + * RURAMPS4DUE (Hotend0, Hotend1, Hotend2, Fan0, Fan1, Bed) + * + * Differences between + * RADDS | RuRAMPS4DUE + * | + */ + +#if NOT_TARGET(__SAM3X8E__) + #error "Oops! Select 'Arduino Due' in 'Tools > Board.'" +#endif + +#define BOARD_INFO_NAME "RuRAMPS4Due v1.1" + +// +// Servos +// +#define SERVO0_PIN 5 +#define SERVO1_PIN 3 + +// +// Limit Switches +// +#define X_MIN_PIN 45 +#define X_MAX_PIN 39 +#define Y_MIN_PIN 46 +#define Y_MAX_PIN 41 +#define Z_MIN_PIN 47 +#define Z_MAX_PIN 43 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 43 +#endif + +// +// Steppers +// +#define X_STEP_PIN 37 // Support Extension Board +#define X_DIR_PIN 36 +#define X_ENABLE_PIN 38 +#ifndef X_CS_PIN + #define X_CS_PIN -1 +#endif + +#define Y_STEP_PIN 32 // Support Extension Board +#define Y_DIR_PIN 35 +#define Y_ENABLE_PIN 34 +#ifndef Y_CS_PIN + #define Y_CS_PIN -1 +#endif + +#define Z_STEP_PIN 30 // Support Extension Board +#define Z_DIR_PIN 2 +#define Z_ENABLE_PIN 33 +#ifndef Z_CS_PIN + #define Z_CS_PIN -1 +#endif + +#define E0_STEP_PIN 29 +#define E0_DIR_PIN 28 +#define E0_ENABLE_PIN 31 +#ifndef E0_CS_PIN + #define E0_CS_PIN -1 +#endif + +#define E1_STEP_PIN 22 +#define E1_DIR_PIN 24 +#define E1_ENABLE_PIN 26 +#ifndef E1_CS_PIN + #define E1_CS_PIN -1 +#endif + +#define E2_STEP_PIN 25 +#define E2_DIR_PIN 23 +#define E2_ENABLE_PIN 27 +#ifndef E2_CS_PIN + #define E2_CS_PIN -1 +#endif + +#define E3_STEP_PIN 15 // Only For Extension Board +#define E3_DIR_PIN 14 +#define E3_ENABLE_PIN 61 +#ifndef E3_CS_PIN + #define E3_CS_PIN -1 +#endif + +// For Future: Microstepping pins - Mapping not from fastio.h (?) +//#define E3_MS1_PIN ? +//#define E3_MS2_PIN ? +//#define E3_MS3_PIN ? + +#if HAS_CUSTOM_PROBE_PIN + #define Z_MIN_PROBE_PIN 49 +#endif + +#if HAS_FILAMENT_SENSOR + #ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN Y_MIN_PIN + #endif +#endif + +// +// Heaters / Fans +// +#define HEATER_0_PIN 13 +#define HEATER_1_PIN 12 +#define HEATER_2_PIN 11 +#define HEATER_BED_PIN 7 // BED H1 + +#ifndef FAN_PIN + #define FAN_PIN 9 +#endif +#define FAN1_PIN 8 +#define CONTROLLER_FAN_PIN -1 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // ANALOG A0 +#define TEMP_1_PIN 1 // ANALOG A1 +#define TEMP_2_PIN 2 // ANALOG A2 +#define TEMP_3_PIN 3 // ANALOG A3 +#define TEMP_BED_PIN 4 // ANALOG A4 + +// The thermocouple uses Analog pins +#if ENABLED(VER_WITH_THERMOCOUPLE) // Defined in Configuration.h + #define TEMP_4_PIN 5 // A5 + #define TEMP_5_PIN 6 // A6 (Marlin 2.0 not support) +#endif + +// SPI for Max6675 or Max31855 Thermocouple +/* +#if DISABLED(SDSUPPORT) + #define MAX6675_SS_PIN 53 +#else + #define MAX6675_SS_PIN 49 +#endif +*/ + +// +// Misc. Functions +// +#define SDSS 4 // 4,10,52 if using HW SPI. +#define LED_PIN -1 // 13 - HEATER_0_PIN +#define PS_ON_PIN -1 // 65 + +// MKS TFT / Nextion Use internal USART-1 +#define TFT_LCD_MODULE_COM 1 +#define TFT_LCD_MODULE_BAUDRATE 115600 + +// ESP WiFi Use internal USART-2 +#define ESP_WIFI_MODULE_COM 2 +#define ESP_WIFI_MODULE_BAUDRATE 115600 +#define ESP_WIFI_MODULE_RESET_PIN -1 +#define PIGGY_GPIO_PIN -1 + +// +// EEPROM +// +#define MARLIN_EEPROM_SIZE 0x8000 // 32Kb (24lc256) +#define I2C_EEPROM // EEPROM on I2C-0 +//#define EEPROM_SD // EEPROM on SDCARD +//#define SPI_EEPROM // EEPROM on SPI-0 +//#define SPI_CHAN_EEPROM1 ? +//#define SPI_EEPROM1_CS ? +// 2K EEPROM +//#define SPI_EEPROM2_CS ? +// 32Mb FLASH +//#define SPI_FLASH_CS ? + +// +// LCD / Controller +// +#if HAS_WIRED_LCD + + #if ANY(RADDS_DISPLAY, IS_RRD_SC, IS_RRD_FG_SC) + #define BEEPER_PIN 62 + #define LCD_PINS_D4 48 + #define LCD_PINS_D5 50 + #define LCD_PINS_D6 52 + #define LCD_PINS_D7 53 + #define SD_DETECT_PIN 51 + #endif + + #if EITHER(RADDS_DISPLAY, IS_RRD_SC) + + #define LCD_PINS_RS 63 + #define LCD_PINS_ENABLE 64 + + #elif IS_RRD_FG_SC + + #define LCD_PINS_RS 52 + #define LCD_PINS_ENABLE 53 + + #elif HAS_U8GLIB_I2C_OLED + + #define BEEPER_PIN 62 + #define LCD_SDSS 10 + #define SD_DETECT_PIN 51 + + #elif ENABLED(FYSETC_MINI_12864) + + #define BEEPER_PIN 62 + #define DOGLCD_CS 64 + #define DOGLCD_A0 63 + + //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems + // results in LCD soft SPI mode 3, SD soft SPI mode 0 + + #define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally. + + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 50 // D5 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 52 // D6 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 53 // D7 + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #define NEOPIXEL_PIN 50 // D5 + #endif + + #elif ENABLED(SPARK_FULL_GRAPHICS) + + //http://doku.radds.org/dokumentation/other-electronics/sparklcd/ + #error "Oops! SPARK_FULL_GRAPHICS not supported with RURAMPS4D." + //#define LCD_PINS_D4 29 //? + //#define LCD_PINS_ENABLE 27 //? + //#define LCD_PINS_RS 25 //? + //#define BTN_EN1 35 //? + //#define BTN_EN2 33 //? + //#define BTN_ENC 37 //? + + #endif // SPARK_FULL_GRAPHICS + + #if IS_NEWPANEL + #define BTN_EN1 44 + #define BTN_EN2 42 + #define BTN_ENC 40 + #endif + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + +#endif // HAS_WIRED_LCD |