diff options
Diffstat (limited to 'Marlin/src/pins/sanguino/pins_ANET_10.h')
| -rw-r--r-- | Marlin/src/pins/sanguino/pins_ANET_10.h | 289 |
1 files changed, 289 insertions, 0 deletions
diff --git a/Marlin/src/pins/sanguino/pins_ANET_10.h b/Marlin/src/pins/sanguino/pins_ANET_10.h new file mode 100644 index 0000000..fb1b6db --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_ANET_10.h @@ -0,0 +1,289 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Anet V1.0 board pin assignments + */ + +/** + * Rev B 16 JUN 2017 + * + * 1) no longer uses Sanguino files to define some of the pins + * 2) added pointers to useable Arduino IDE extensions + */ + +/** + * The standard Arduino IDE extension (board manager) for this board + * is located at https://github.com/SkyNet3D/anet-board. + * + * Installation instructions are on that page. + * + * After copying the files to the appropriate location, restart Arduino and + * you'll see "Anet V1.0" and "Anet V1.0 (Optiboot)" in the boards list. + * + * "Anet V1.0" uses the bootloader that was installed on the board when + * it shipped from the factory. + * + * "Anet V1.0 (Optiboot)" frees up another 3K of FLASH. You'll need to burn + * a new bootloader to the board to be able to automatically download a + * compiled image. + */ + +/** + * Another usable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +/** + * To burn a new bootloader: + * + * 1. Connect your programmer to the board. + * 2. In the Arduino IDE select the board and then select the programmer. + * 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. + * 4. The programmer is no longer needed. Remove it. + */ + +/** + * Additional info: + * + * Anet Schematics - https://github.com/ralf-e/ANET-3D-Board-V1.0 + * Wiring RRDFG Smart Controller - https://www.thingiverse.com/thing:2103748 + * SkyNet3D Anet software development - https://github.com/SkyNet3D/Marlin/ + * Anet Users / Skynet SW on Facebook - https://www.facebook.com/skynet3ddevelopment/ + * + * Many thanks to Hans Raaf (@oderwat) for developing the Anet-specific software and supporting the Anet community. + */ + +#if NOT_TARGET(__AVR_ATmega1284P__) + #error "Oops! Select 'Sanguino' in 'Tools > Board' and 'ATmega1284P' in 'Tools > Processor.' (For PlatformIO, use 'melzi' or 'melzi_optiboot.')" +#endif + +#define BOARD_INFO_NAME "Anet 1.0" + +// +// Limit Switches +// +#define X_STOP_PIN 18 +#define Y_STOP_PIN 19 +#define Z_STOP_PIN 20 + +// +// Steppers +// +#define X_STEP_PIN 15 +#define X_DIR_PIN 21 +#define X_ENABLE_PIN 14 + +#define Y_STEP_PIN 22 +#define Y_DIR_PIN 23 +#define Y_ENABLE_PIN 14 + +#define Z_STEP_PIN 3 +#define Z_DIR_PIN 2 +#define Z_ENABLE_PIN 26 + +#define E0_STEP_PIN 1 +#define E0_DIR_PIN 0 +#define E0_ENABLE_PIN 14 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 7 // Analog Input (pin 33 extruder) +#define TEMP_BED_PIN 6 // Analog Input (pin 34 bed) + +// +// Heaters / Fans +// +#define HEATER_0_PIN 13 // (extruder) +#define HEATER_BED_PIN 12 // (bed) + +#ifndef FAN_PIN + #define FAN_PIN 4 +#endif + +// +// Misc. Functions +// +#define SDSS 31 +#define LED_PIN -1 + +/** + * LCD / Controller + * + * Only the following displays are supported: + * ZONESTAR_LCD + * ANET_FULL_GRAPHICS_LCD(_ALT_WIRING)? + * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + */ + +#if HAS_WIRED_LCD + + #define LCD_SDSS 28 + + #if HAS_ADC_BUTTONS + + #define SERVO0_PIN 27 // free for BLTouch/3D-Touch + #define LCD_PINS_RS 28 + #define LCD_PINS_ENABLE 29 + #define LCD_PINS_D4 10 + #define LCD_PINS_D5 11 + #define LCD_PINS_D6 16 + #define LCD_PINS_D7 17 + #define ADC_KEYPAD_PIN 1 + + #elif IS_RRD_FG_SC + + // Pin definitions for the Anet A6 Full Graphics display and the RepRapDiscount Full Graphics + // display using an adapter board // https://go.aisler.net/benlye/anet-lcd-adapter/pcb + // See below for alternative pin definitions for use with https://www.thingiverse.com/thing:2103748 + + #if ENABLED(ANET_FULL_GRAPHICS_LCD_ALT_WIRING) + #define SERVO0_PIN 30 + #define BEEPER_PIN 27 + #define LCD_PINS_RS 29 + #define LCD_PINS_ENABLE 16 + #define LCD_PINS_D4 11 + #define BTN_EN1 28 + #define BTN_EN2 10 + #define BTN_ENC 17 + #define BOARD_ST7920_DELAY_1 DELAY_NS(250) + #define BOARD_ST7920_DELAY_2 DELAY_NS(250) + #define BOARD_ST7920_DELAY_3 DELAY_NS(250) + #else + #define SERVO0_PIN 29 // free for BLTouch/3D-Touch + #define BEEPER_PIN 17 + #define LCD_PINS_RS 27 + #define LCD_PINS_ENABLE 28 + #define LCD_PINS_D4 30 + #define BTN_EN1 11 + #define BTN_EN2 10 + #define BTN_ENC 16 + #define BOARD_ST7920_DELAY_1 DELAY_NS(0) + #define BOARD_ST7920_DELAY_2 DELAY_NS(63) + #define BOARD_ST7920_DELAY_3 DELAY_NS(125) + #endif + + #endif + +#else + #define SERVO0_PIN 27 +#endif + +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN SERVO0_PIN +#endif + +/** + * ==================================================================== + * =============== Alternative RepRapDiscount Wiring ================== + * ==================================================================== + * + * An alternative wiring scheme for the RepRapDiscount Full Graphics Display is + * published by oderwat on Thingiverse at https://www.thingiverse.com/thing:2103748. + * + * Using that adapter requires changing the pin definition as follows: + * #define SERVO0_PIN 27 // free for BLTouch/3D-Touch + * #define BEEPER_PIN 28 + * #define LCD_PINS_RS 30 + * #define LCD_PINS_ENABLE 29 + * #define LCD_PINS_D4 17 + * + * The BLTouch pin becomes LCD:3 + */ + +/** + * ==================================================================== + * ===================== LCD PINOUTS ================================== + * ==================================================================== + * + * Anet V1.0 controller | ZONESTAR_LCD | ANET_FULL_ | RepRapDiscount Full | Thingiverse RepRap wiring + * physical logical alt | | GRAPHICS_LCD | Graphics Display Wiring | https://www.thingiverse + * pin pin functions | | | | .com/thing:2103748 + *------------------------------------------------------------------------------------------------------------------------ + * ANET-J3.1 8 *** | N/A | J3_TX *** | | + * ANET-J3.2 9 *** | N/A | J3_RX *** | | + * ANET-J3.3 6 MISO | N/A | MISO *** | EXP2.1 MISO | EXP2.1 MISO + * ANET-J3.4 +5V | N/A | +5V | | + * ANET-J3.5 7 SCK | N/A | SCK *** | EXP2.2 SCK | EXP2.2 SCK + * ANET-J3.6 5 MOSI | N/A | MOSI *** | EXP2.6 MOSI | EXP2.6 MOSI + * ANET-J3.7 !RESET | N/A | button | EXP2.8 panel button | EXP2.8 panel button + * ANET-J3.8 GND | N/A | GND | EXP2.9 GND | EXP2.9 GND + * ANET-J3.9 4 Don't use | N/A | N/C | | + * ANET-J3.10 +3.3V | N/A | +3.3V *** | | + * | | | | + * | | | | + * ANET-LCD.1 GND | GND | GND | EXP1.9 GND | EXP1.9 GND + * ANET-LCD.2 +5V | +5V | +5V | EXP1.10 +5V | EXP1.10 +5V + * ANET-LCD.3 27 A4 | N/C * | LCD_PINS_RS | EXP1.4 LCD_PINS_RS | EXP2.4 SDSS or N/C * + * ANET-LCD.4 10 | LCD_PINS_D4 | BTN_EN2 | EXP2.3 BTN_EN2 | EXP2.3 BTN_EN2 + * ANET-LCD.5 28 A3 | LCD_PINS_RS | LCD_PINS_ENABLE | EXP1.3 LCD_PINS_ENABLE | EXP1.1 BEEPER_PIN + * ANET-LCD.6 11 | LCD_PINS_D5 | BTN_EN1 | EXP2.5 BTN_EN1 | EXP2.5 BTN_EN1 + * ANET-LCD.7 29 A2 | LCD_PINS_ENABLE | N/C * | EXP2.4 SDSS or N/C * | EXP1.3 LCD_PINS_ENABLE + * ANET-LCD.8 16 SCL | LCD_PINS_D6 | BTN_ENC | EXP1.2 BTN_ENC | EXP1.2 BTN_ENC + * ANET-LCD.9 30 A1 | ADC_KEYPAD_PIN ** | LCD_PINS_D4 | EXP1.5 LCD_PINS_D4 | EXP1.4 LCD_PINS_RS + * ANET-LCD.10 17 SDA | LCD_PINS_D7 | BEEPER_PIN | EXP1.1 BEEPER_PIN | EXP1.5 LCD_PINS_D4 + * + * N/C * - if not connected to the LCD can be used for BLTouch servo input + * ** - analog pin -WITHOUT a pullup + * *** - only connected to something if the Bluetooth module is populated + */ + +/** + * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + * physical pin function + * EXP1.1 BEEPER + * EXP1.2 BTN_ENC + * EXP1.3 LCD_PINS_ENABLE + * EXP1.4 LCD_PINS_RS + * EXP1.5 LCD_PINS_D4 + * EXP1.6 LCD_PINS_D5 (not used) + * EXP1.7 LCD_PINS_D6 (not used) + * EXP1.8 LCD_PINS_D7 (not used) + * EXP1.9 GND + * EXP1.10 VCC + * + * + * EXP2.1 MISO + * EXP2.2 SCK + * EXP2.3 BTN_EN2 + * EXP2.4 SDSS + * EXP2.5 BTN_EN1 + * EXP2.6 MOSI + * EXP2.7 SD_DETECT_PIN + * EXP2.8 button + * EXP2.9 GND + * EXP2.10 NC + */ |