diff options
Diffstat (limited to 'Marlin/src/pins/sanguino/pins_OMCA.h')
| -rw-r--r-- | Marlin/src/pins/sanguino/pins_OMCA.h | 149 |
1 files changed, 149 insertions, 0 deletions
diff --git a/Marlin/src/pins/sanguino/pins_OMCA.h b/Marlin/src/pins/sanguino/pins_OMCA.h new file mode 100644 index 0000000..7f18283 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_OMCA.h @@ -0,0 +1,149 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Open Motion controller with enable based extruders (Final!) + * + * ATmega644 + * + * +---\/---+ + * (D 0) PB0 1| |40 PA0 (AI 0 / D31) + * (D 1) PB1 2| |39 PA1 (AI 1 / D30) + * INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29) + * PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28) + * PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27) + * MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26) + * MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25) + * SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24) + * RST 9| |32 AREF + * VCC 10| |31 GND + * GND 11| |30 AVCC + * XTAL2 12| |29 PC7 (D 23) + * XTAL1 13| |28 PC6 (D 22) + * RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI + * TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO + * INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS + * INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK + * PWM (D 12) PD4 18| |23 PC1 (D 17) SDA + * PWM (D 13) PD5 19| |22 PC0 (D 16) SCL + * PWM (D 14) PD6 20| |21 PD7 (D 15) PWM + * +--------+ + * + * REF http://sanguino.wikidot.com/hardware + */ + +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at http://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega644__) + #error "Oops! Select 'Sanguino' in 'Tools > Board' and 'ATmega644' or 'ATmega644P' in 'Tools > Processor.'" +#endif + +#define BOARD_INFO_NAME "Final OMCA" + +// +// Limit Switches +// +#define X_STOP_PIN 0 +#define Y_STOP_PIN 1 +#define Z_STOP_PIN 2 + +// +// Steppers +// +#define X_STEP_PIN 26 +#define X_DIR_PIN 25 +#define X_ENABLE_PIN 10 + +#define Y_STEP_PIN 28 +#define Y_DIR_PIN 27 +#define Y_ENABLE_PIN 10 + +#define Z_STEP_PIN 23 +#define Z_DIR_PIN 22 +#define Z_ENABLE_PIN 10 + +#define E0_STEP_PIN 24 +#define E0_DIR_PIN 21 +#define E0_ENABLE_PIN 10 + +#define E1_STEP_PIN -1 // 21 +#define E1_DIR_PIN -1 // 20 +#define E1_ENABLE_PIN -1 // 19 + +#define E2_STEP_PIN -1 // 21 +#define E2_DIR_PIN -1 // 20 +#define E2_ENABLE_PIN -1 // 18 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // Analog Input +#define TEMP_1_PIN 1 // Analog Input +#define TEMP_BED_PIN 2 // Analog Input (1,2 or I2C) + +// +// Heaters / Fans +// +#define HEATER_0_PIN 3 // DONE PWM on RIGHT connector +#define HEATER_BED_PIN 4 + +#ifndef FAN_PIN + #define FAN_PIN 14 // PWM on MIDDLE connector +#endif + +// +// Misc. Functions +// +#define SDSS 11 + +#define I2C_SCL_PIN 16 +#define I2C_SDA_PIN 17 + +// future proofing +#define __FS 20 +#define __FD 19 +#define __GS 18 +#define __GD 13 + +#define UNUSED_PWM 14 // PWM on LEFT connector |