diff options
Diffstat (limited to 'Marlin/src/pins/sanguino/pins_ZMIB_V2.h')
| -rw-r--r-- | Marlin/src/pins/sanguino/pins_ZMIB_V2.h | 234 |
1 files changed, 234 insertions, 0 deletions
diff --git a/Marlin/src/pins/sanguino/pins_ZMIB_V2.h b/Marlin/src/pins/sanguino/pins_ZMIB_V2.h new file mode 100644 index 0000000..d064d80 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_ZMIB_V2.h @@ -0,0 +1,234 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega1284P__) + #error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644P' or 'ATmega1284P' in 'Tools > Processor.'" +#endif + +#define BOARD_INFO_NAME "Zonestar ZMIB_V2" +#define BOARD_WEBSITE_URL "www.aliexpress.com/item/32957490744.html" + +#define IS_ZMIB_V2 + +/** + * ZMIB pin assignments + * + * The ZMIB board needs a bootloader installed before Marlin can be uploaded. + * If you don't have a chip programmer you can use a spare Arduino plus a few + * electronic components to write the bootloader. + * + * See http://www.instructables.com/id/Burn-Arduino-Bootloader-with-Arduino-MEGA/ + */ + +/** + * PIN: 0 Port: B0 HEATER_0_PIN + * PIN: 1 Port: B1 HEATER_BED_PIN + * PIN: 2 Port: B2 EXP1_4(BTN_EN2) + * PIN: 3 Port: B3 V1: SD_DETECT_PIN + * PIN: 3 Port: B3 V2: EXP1_6 + * PIN: 4 Port: B4 SDSS + * PIN: 4 Port: B4 V1: EXP1_6 + * PIN: 5 Port: B5 AVR_MOSI_PIN + * . SD_MOSI_PIN + * PIN: 6 Port: B6 AVR_MISO_PIN + * . EXP1_9(SD_MISO_PIN) + * PIN: 7 Port: B7 AVR_SCK_PIN + * . EXP1_10(SD_SCK_PIN) + * PIN: 8 Port: D0 RXD + * PIN: 9 Port: D1 TXD + * PIN: 10 Port: D2 EXP1_8 + * PIN: 11 Port: D3 EXP1_7 + * PIN: 12 Port: D4 EXP1_5(BTN_EN1) + * PIN: 13 Port: D5 Z_MIN_PIN + * PIN: 14 Port: D6 E1_DIR_PIN + * PIN: 15 Port: D7 E1_STEP_PIN + * PIN: 16 Port: C0 Z_DIR_PIN + * PIN: 17 Port: C1 Z_STEP_PIN + * PIN: 18 Port: C2 Y_MIN_PIN + * PIN: 19 Port: C3 Y_DIR_PIN + * PIN: 20 Port: C4 Y_STEP_PIN + * PIN: 21 Port: C5 X_MIN_PIN + * PIN: 22 Port: C6 X_DIR_PIN + * PIN: 23 Port: C7 X_STEP_PIN + * PIN: 24 Port: A7 X_ENABLE_PIN + * Y_ENABLE_PIN + * Z_ENABLE_PIN + * E0_ENABLE_PIN + * E1_ENABLE_PIN + * PIN: 25 Port: A6 FIL_RUNOUT_PIN + * PIN: 26 Port: A5 E0_DIR_PIN + * PIN: 27 Port: A4 E0_STEP_PIN + * PIN: 28 Port: A3 FAN_PIN + * PIN: 29 Port: A2 EXP1_3(BTN_ENC) + * ADC_KEY_PIN + * PIN: 30 Port: A1 TEMP_0_PIN + * PIN: 31 Port: A0 TEMP_BED_PIN + */ + +// +// Limit Switches +// +#define X_MIN_PIN 21 +#define Y_MIN_PIN 18 + +#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT) + #define Z_MIN_PIN 25 +#else + #define Z_MIN_PIN 13 +#endif + +// +// Steppers +// +#define X_STEP_PIN 23 +#define X_DIR_PIN 22 +#define X_ENABLE_PIN 24 + +#define Y_STEP_PIN 20 +#define Y_DIR_PIN 19 +#define Y_ENABLE_PIN 24 + +#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT) + #define Z_STEP_PIN 27 + #define Z_DIR_PIN 26 +#else + #define Z_STEP_PIN 17 + #define Z_DIR_PIN 16 +#endif + +#define Z_ENABLE_PIN 24 + +#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT) + #define E0_STEP_PIN 15 + #define E0_DIR_PIN 14 +#else + #define E0_STEP_PIN 27 + #define E0_DIR_PIN 26 +#endif + +#define E0_ENABLE_PIN 24 + +#define E1_STEP_PIN 15 +#define E1_DIR_PIN 14 +#define E1_ENABLE_PIN 24 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 1 // Analog Input +#define TEMP_BED_PIN 0 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 0 +#define HEATER_BED_PIN 1 +#define FAN_PIN 28 +#define FAN1_PIN -1 + +// +//filament run out sensor +// +#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT) + #define FIL_RUNOUT_PIN 13 +#else + #define FIL_RUNOUT_PIN 25 // Z-MIN +#endif + +// +// SD card +// +#if ENABLED(SDSUPPORT) + #define SDSS 4 +#endif +#define SD_DETECT_PIN -1 + +/*=================================================== + * ZMIB Version 1 - EXP1 Connector + * MOSI(D5) TX1(D11) ENA(D12) ENC(D29/A2) 5V + * SCK(D7) RX1(D10) SCS(D4) ENB(D2) GND + *=================================================== + * ZMIB Version 2 - EXP1 Connector + * MOSI(D5) TX1(D11) ENA(D12) ENC(D29/A2) 5V + * SCK(D7) RX1(D10) SCS(D3) ENB(D2) GND + *=================================================== + * LCD 128x64 + *==================================================*/ + +#if ENABLED(ZONESTAR_12864LCD) + // + // LCD 128x64 + // + #define LCDSCREEN_NAME "ZONESTAR_12864LCD" + #define FORCE_SOFT_SPI + //#define LCD_SDSS 11 + #define LCD_PINS_RS 11 // ST7920_CS_PIN LCD_PIN_RS (PIN4 of LCD module) + #ifdef IS_ZMIB_V2 + #define LCD_PINS_ENABLE 3 // ST7920_DAT_PIN LCD_PIN_R/W (PIN5 of LCD module) + #else + #define LCD_PINS_ENABLE 4 // ST7920_DAT_PIN LCD_PIN_R/W (PIN5 of LCD module) + #endif + #define LCD_PINS_D4 10 // ST7920_CLK_PIN LCD_PIN_ENABLE (PIN6 of LCD module) + + // Alter timing for graphical display + #define ST7920_DELAY_1 DELAY_2_NOP + #define ST7920_DELAY_2 DELAY_2_NOP + #define ST7920_DELAY_3 DELAY_2_NOP + +#elif EITHER(ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306) + // + // OLED 128x64 + // + #define LCDSCREEN_NAME "ZONESTAR 12864OLED" + #define FORCE_SOFT_SPI + #ifdef IS_ZMIB_V2 + #define LCD_PINS_RS 3 // RESET + #else + #define LCD_PINS_RS 4 // RESET + #endif + #define LCD_PINS_DC 10 // DC + #define DOGLCD_CS 11 // CS + #if ENABLED(OLED_HW_IIC) + #error "Oops! can't choose HW IIC for ZMIB board!!" + #elif ENABLED(OLED_HW_SPI) + // HW SPI + #define DOGLCD_A0 LCD_PINS_DC // A0 = DC + #else + // SW SPI + #define DOGLCD_A0 LCD_PINS_DC // A0 = DC + #define DOGLCD_MOSI AVR_MOSI_PIN // SDA + #define DOGLCD_SCK AVR_SCK_PIN // SCK + #endif + +#endif + +// +// All the above are also RRDSC with rotary encoder +// +#if IS_RRD_SC + #define BTN_EN1 2 + #define BTN_EN2 12 + #define BTN_ENC 29 + #define BEEPER_PIN -1 + #define KILL_PIN -1 +#endif |