diff options
Diffstat (limited to 'Marlin/src/pins/stm32f4/pins_ANET_ET4.h')
| -rw-r--r-- | Marlin/src/pins/stm32f4/pins_ANET_ET4.h | 222 |
1 files changed, 222 insertions, 0 deletions
diff --git a/Marlin/src/pins/stm32f4/pins_ANET_ET4.h b/Marlin/src/pins/stm32f4/pins_ANET_ET4.h new file mode 100644 index 0000000..487080f --- /dev/null +++ b/Marlin/src/pins/stm32f4/pins_ANET_ET4.h @@ -0,0 +1,222 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ + +#pragma once + +#if NOT_TARGET(STM32F4) + #error "Oops! Select an STM32F4 board in 'Tools > Board.'" +#elif HOTENDS > 1 || E_STEPPERS > 1 + #error "Anet ET4 only supports one hotend / E-stepper. Comment out this line to continue." +#endif + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "Anet ET4 1.x" +#endif + +// +// EEPROM +// + +// Use one of these or SDCard-based Emulation will be used +#if NO_EEPROM_SELECTED + //#define SRAM_EEPROM_EMULATION // Use BackSRAM-based EEPROM emulation + #define FLASH_EEPROM_EMULATION // Use Flash-based EEPROM emulation + //#define IIC_BL24CXX_EEPROM // Use I2C EEPROM onboard IC (AT24C04C, Size 4KB, PageSize 16B) +#endif + +#if ENABLED(FLASH_EEPROM_EMULATION) + // Decrease delays and flash wear by spreading writes across the + // 128 kB sector allocated for EEPROM emulation. + #define FLASH_EEPROM_LEVELING +#elif ENABLED(IIC_BL24CXX_EEPROM) + #define IIC_EEPROM_SDA PB11 + #define IIC_EEPROM_SCL PB10 + #define EEPROM_DEVICE_ADDRESS 0xA0 + #define MARLIN_EEPROM_SIZE 0x1000 // 4KB +#endif + +// +// Limit Switches +// +#define X_STOP_PIN PC13 +#define Y_STOP_PIN PE12 +#define Z_STOP_PIN PE11 + +// +// Z Probe +// +#if ENABLED(BLTOUCH) + #error "You will need to use 24V to 5V converter and remove one resistor and capacitor from the motherboard. See https://github.com/davidtgbe/Marlin/blob/bugfix-2.0.x/docs/Tutorials/bltouch-en.md for more information. Comment out this line to proceed at your own risk." + #define SERVO0_PIN PC3 +#elif !defined(Z_MIN_PROBE_PIN) + #define Z_MIN_PROBE_PIN PC3 +#endif + +// +// Filament Runout Sensor +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN PA2 +#endif + +// +// Power Loss Detection +// +#ifndef POWER_LOSS_PIN + #define POWER_LOSS_PIN PA8 +#endif + +// +// LED PIN +// +#define LED_PIN PD12 + +// +// Steppers +// +#define X_STEP_PIN PB6 +#define X_DIR_PIN PB5 +#define X_ENABLE_PIN PB7 + +#define Y_STEP_PIN PB3 +#define Y_DIR_PIN PD6 +#define Y_ENABLE_PIN PB4 + +#define Z_STEP_PIN PA12 +#define Z_DIR_PIN PA11 +#define Z_ENABLE_PIN PA15 + +#define E0_STEP_PIN PB9 +#define E0_DIR_PIN PB8 +#define E0_ENABLE_PIN PE0 + +// +// Temperature Sensors +// +#define TEMP_0_PIN PA1 +#define TEMP_BED_PIN PA4 + +// +// Heaters +// +#define HEATER_0_PIN PA0 +#define HEATER_BED_PIN PE2 + +// +// Fans +// +#define FAN_PIN PE3 // Layer fan +#define FAN1_PIN PE1 // Hotend fan + +#ifndef E0_AUTO_FAN_PIN + #define E0_AUTO_FAN_PIN FAN1_PIN +#endif + +// +// LCD / Controller +// +#define TFT_RESET_PIN PE6 +#define TFT_CS_PIN PD7 +#define TFT_RS_PIN PD13 +#define TFT_INTERFACE_FSMC_8BIT + +#define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT +#define FSMC_CS_PIN TFT_CS_PIN +#define FSMC_RS_PIN TFT_RS_PIN + +// +// Touch Screen +// https://ldm-systems.ru/f/doc/catalog/HY-TFT-2,8/XPT2046.pdf +// +#if NEED_TOUCH_PINS + #define TOUCH_CS_PIN PB2 + #define TOUCH_SCK_PIN PB0 + #define TOUCH_MOSI_PIN PE5 + #define TOUCH_MISO_PIN PE4 + #define TOUCH_INT_PIN PB1 +#endif + +#if ENABLED(ANET_ET5_TFT35) + #ifndef TOUCH_CALIBRATION_X + #define TOUCH_CALIBRATION_X 17125 + #endif + #ifndef TOUCH_CALIBRATION_Y + #define TOUCH_CALIBRATION_Y -11307 + #endif + #ifndef TOUCH_OFFSET_X + #define TOUCH_OFFSET_X -26 + #endif + #ifndef TOUCH_OFFSET_Y + #define TOUCH_OFFSET_Y 337 + #endif + #ifndef TOUCH_ORIENTATION + #define TOUCH_ORIENTATION TOUCH_PORTRAIT + #endif +#elif ENABLED(ANET_ET4_TFT28) + #ifndef TOUCH_CALIBRATION_X + #define TOUCH_CALIBRATION_X -11838 + #endif + #ifndef TOUCH_CALIBRATION_Y + #define TOUCH_CALIBRATION_Y 8776 + #endif + #ifndef TOUCH_OFFSET_X + #define TOUCH_OFFSET_X 333 + #endif + #ifndef TOUCH_OFFSET_Y + #define TOUCH_OFFSET_Y -17 + #endif + #ifndef TOUCH_ORIENTATION + #define TOUCH_ORIENTATION TOUCH_PORTRAIT + #endif +#endif + +// +// SD Card +// +//#define SDIO_SUPPORT + +#ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION CUSTOM_CABLE +#endif + +#if ENABLED(SDSUPPORT) + + #define SDIO_D0_PIN PC8 + #define SDIO_D1_PIN PC9 + #define SDIO_D2_PIN PC10 + #define SDIO_D3_PIN PC11 + #define SDIO_CK_PIN PC12 + #define SDIO_CMD_PIN PD2 + + #if DISABLED(SDIO_SUPPORT) + #define SOFTWARE_SPI + #define SDSS SDIO_D3_PIN + #define SD_SCK_PIN SDIO_CK_PIN + #define SD_MISO_PIN SDIO_D0_PIN + #define SD_MOSI_PIN SDIO_CMD_PIN + #endif + + #ifndef SD_DETECT_PIN + #define SD_DETECT_PIN PD3 + #endif + +#endif |