diff options
Diffstat (limited to 'Marlin/src/pins/stm32f4/pins_ARMED.h')
| -rw-r--r-- | Marlin/src/pins/stm32f4/pins_ARMED.h | 229 |
1 files changed, 229 insertions, 0 deletions
diff --git a/Marlin/src/pins/stm32f4/pins_ARMED.h b/Marlin/src/pins/stm32f4/pins_ARMED.h new file mode 100644 index 0000000..db57db1 --- /dev/null +++ b/Marlin/src/pins/stm32f4/pins_ARMED.h @@ -0,0 +1,229 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ + +// https://github.com/ktand/Armed + +#pragma once + +#if NOT_TARGET(STM32F4) + #error "Oops! Select an STM32F4 board in 'Tools > Board.'" +#elif HOTENDS > 2 || E_STEPPERS > 2 + #error "Arm'ed supports up to 2 hotends / E-steppers." +#endif + +#ifndef ARMED_V1_0 + #define ARMED_V1_1 +#endif + +#undef BOARD_INFO_NAME // Defined on the command line by Arduino Core STM32 +#define BOARD_INFO_NAME "Arm'ed" +#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME + +#define I2C_EEPROM +#define MARLIN_EEPROM_SIZE 0x1000 // 4KB + +// +// Limit Switches +// +#define X_STOP_PIN PE0 +#define Y_STOP_PIN PE1 +#define Z_STOP_PIN PE14 + +// +// Z Probe (when not Z_MIN_PIN) +// +//#ifndef Z_MIN_PROBE_PIN +// #define Z_MIN_PROBE_PIN PA4 +//#endif + +// +// Filament Runout Sensor +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN PA3 +#endif + +// +// Steppers +// + +#ifdef ARMED_SWAP_X_E1 + #define X_STEP_PIN PE4 + #define X_DIR_PIN PE2 + #define X_ENABLE_PIN PE3 + #define X_CS_PIN PE5 +#else + #define X_STEP_PIN PD3 + #define X_DIR_PIN PD2 + #define X_ENABLE_PIN PD0 + #define X_CS_PIN PD1 +#endif + +#define Y_STEP_PIN PE11 +#define Y_DIR_PIN PE10 +#define Y_ENABLE_PIN PE13 +#define Y_CS_PIN PE12 + +#define Z_STEP_PIN PD6 +#define Z_DIR_PIN PD7 +#define Z_ENABLE_PIN PD4 +#define Z_CS_PIN PD5 + +#define E0_STEP_PIN PB5 +#define E0_DIR_PIN PB6 +#ifdef ARMED_V1_1 + #define E0_ENABLE_PIN PC12 +#else + #define E0_ENABLE_PIN PB3 +#endif +#define E0_CS_PIN PB4 + +#ifdef ARMED_SWAP_X_E1 + #define E1_STEP_PIN PD3 + #define E1_DIR_PIN PD2 + #define E1_ENABLE_PIN PD0 + #define E1_CS_PIN PD1 +#else + #define E1_STEP_PIN PE4 + #define E1_DIR_PIN PE2 + #define E1_ENABLE_PIN PE3 + #define E1_CS_PIN PE5 +#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN PC0 // Analog Input +#define TEMP_1_PIN PC1 // Analog Input +#define TEMP_BED_PIN PC2 // Analog Input + +#if HOTENDS == 1 && TEMP_SENSOR_PROBE + #define TEMP_PROBE_PIN PC1 +#endif + +// +// Heaters / Fans +// +#define HEATER_0_PIN PA1 // Hardware PWM +#define HEATER_1_PIN PA2 // Hardware PWM +#define HEATER_BED_PIN PA0 // Hardware PWM + +#define FAN_PIN PC6 // Hardware PWM, Part cooling fan +#define FAN1_PIN PC7 // Hardware PWM, Extruder fan +#define FAN2_PIN PC8 // Hardware PWM, Controller fan + +// +// Misc functions +// +#define SDSS PE7 +#define LED_PIN PB7 // Heart beat +#define PS_ON_PIN PA10 +#define KILL_PIN PA8 +#define PWR_LOSS PA4 // Power loss / nAC_FAULT + +// +// LCD / Controller +// +#define SD_DETECT_PIN PA15 +#define BEEPER_PIN PC9 + +#if ENABLED(FYSETC_MINI_12864) + // + // See https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8 + // + #define DOGLCD_A0 PE9 + #define DOGLCD_CS PE8 + + #define LCD_BACKLIGHT_PIN -1 + + #define LCD_RESET_PIN PB12 // Must be high or open for LCD to operate normally. + + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN PB13 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN PB14 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN PB15 + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #define NEOPIXEL_PIN PB13 + #endif +#else + #define LCD_PINS_RS PE9 + #define LCD_PINS_ENABLE PE8 + #define LCD_PINS_D4 PB12 + #define LCD_PINS_D5 PB13 + #define LCD_PINS_D6 PB14 + #define LCD_PINS_D7 PB15 + + #if ENABLED(MKS_MINI_12864) + #define DOGLCD_CS PB13 + #define DOGLCD_A0 PB14 + #endif +#endif + +#define BTN_EN1 PC4 +#define BTN_EN2 PC5 +#define BTN_ENC PC3 + +// +// Extension pins +// +#define EXT0_PIN PB0 +#define EXT1_PIN PB1 +#define EXT2_PIN PB2 +#define EXT3_PIN PD8 +#define EXT4_PIN PD9 +#define EXT5_PIN PD10 +#define EXT6_PIN PD11 +#define EXT7_PIN PD12 +#define EXT8_PIN PB10 +#define EXT9_PIN PB11 + +#if HAS_TMC_UART + // TMC2208/TMC2209 stepper drivers + // + // Software serial + // + #define X_SERIAL_TX_PIN EXT0_PIN + #define X_SERIAL_RX_PIN EXT0_PIN + + #define Y_SERIAL_TX_PIN EXT1_PIN + #define Y_SERIAL_RX_PIN EXT1_PIN + + #define Z_SERIAL_TX_PIN EXT2_PIN + #define Z_SERIAL_RX_PIN EXT2_PIN + + #define E0_SERIAL_TX_PIN EXT3_PIN + #define E0_SERIAL_RX_PIN EXT3_PIN + + #define E1_SERIAL_RX_PIN EXT4_PIN + #define E1_SERIAL_TX_PIN EXT4_PIN + + #define Z2_SERIAL_RX_PIN EXT4_PIN + #define Z2_SERIAL_TX_PIN EXT4_PIN + + #define TMC_BAUD_RATE 19200 +#endif |