diff options
Diffstat (limited to 'buildroot/share/PlatformIO/variants/MARLIN_F103Zx')
6 files changed, 1461 insertions, 0 deletions
diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/PeripheralPins.c b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/PeripheralPins.c new file mode 100644 index 0000000..5736e52 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/PeripheralPins.c @@ -0,0 +1,368 @@ +/* + ******************************************************************************* + * Copyright (c) 2019, STMicroelectronics + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ******************************************************************************* + * Automatically generated from STM32F103Z(C-D-E|F-G))Tx.xml + */ +#include "Arduino.h" +#include "PeripheralPins.h" + +/* ===== + * Note: Commented lines are alternative possibilities which are not used per default. + * If you change them, you will have to know what you do + * ===== + */ + +//*** ADC *** + +#ifdef HAL_ADC_MODULE_ENABLED +WEAK const PinMap PinMap_ADC[] = { + {PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 + // {PA_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC2_IN0 + // {PA_0, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC3_IN0 + {PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 + // {PA_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC2_IN1 + // {PA_1, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC3_IN1 + // {PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 + {PA_2, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC2_IN2 + // {PA_2, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC3_IN2 + {PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 + // {PA_3, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN3 + // {PA_3, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC3_IN3 + // {PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4 + {PA_4, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4 + {PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5 + // {PA_5, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5 + // {PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 + {PA_6, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6 + {PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 + // {PA_7, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7 + // {PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 + {PB_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC2_IN8 + {PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9 + // {PB_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC2_IN9 + // {PC_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10 + {PC_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC2_IN10 + // {PC_0, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC3_IN10 + {PC_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11 + // {PC_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC2_IN11 + // {PC_1, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC3_IN11 + // {PC_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12 + {PC_2, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC2_IN12 + // {PC_2, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC3_IN12 + {PC_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13 + // {PC_3, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC2_IN13 + // {PC_3, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC3_IN13 + // {PC_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14 + {PC_4, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC2_IN14 + {PC_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15 + // {PC_5, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC2_IN15 + {PF_6, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC3_IN4 + {PF_7, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC3_IN5 + {PF_8, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC3_IN6 + {PF_9, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC3_IN7 + {PF_10, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC3_IN8 + {NC, NP, 0} +}; +#endif + +//*** DAC *** + +#ifdef HAL_DAC_MODULE_ENABLED +WEAK const PinMap PinMap_DAC[] = { + {PA_4, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // DAC_OUT1 + {PA_5, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // DAC_OUT2 + {NC, NP, 0} +}; +#endif + +//*** I2C *** + +#ifdef HAL_I2C_MODULE_ENABLED +WEAK const PinMap PinMap_I2C_SDA[] = { + {PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_NONE)}, + {PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_I2C1_ENABLE)}, + {PB_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_NONE)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_I2C_MODULE_ENABLED +WEAK const PinMap PinMap_I2C_SCL[] = { + {PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_NONE)}, + {PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_I2C1_ENABLE)}, + {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_NONE)}, + {NC, NP, 0} +}; +#endif + +//*** PWM *** + +#ifdef HAL_TIM_MODULE_ENABLED +WEAK const PinMap PinMap_PWM[] = { + {PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM2_CH1 + // {PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_2, 1, 0)}, // TIM2_CH1 + // {PA_0, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM5_CH1 + // {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM2_CH2 + // {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_2, 2, 0)}, // TIM2_CH2 + {PA_1, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM5_CH2 + {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM2_CH3 + // {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_1, 3, 0)}, // TIM2_CH3 + // {PA_2, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM5_CH3 +#ifdef STM32F103xG + // {PA_2, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM9_CH1 +#endif + // {PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM2_CH4 + // {PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_1, 4, 0)}, // TIM2_CH4 + {PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM5_CH4 +#ifdef STM32F103xG + // {PA_3, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM9_CH2 +#endif + {PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM3_CH1 +#ifdef STM32F103xG + // {PA_6, TIM13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM13_CH1 +#endif + // {PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 1, 1)}, // TIM1_CH1N + // {PA_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM3_CH2 + {PA_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 1)}, // TIM8_CH1N +#ifdef STM32F103xG + // {PA_7, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM14_CH1 +#endif + {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM1_CH1 + // {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 1, 0)}, // TIM1_CH1 + {PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM1_CH2 + // {PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 2, 0)}, // TIM1_CH2 + {PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM1_CH3 + // {PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 3, 0)}, // TIM1_CH3 + {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM1_CH4 + // {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 4, 0)}, // TIM1_CH4 + {PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_1, 1, 0)}, // TIM2_CH1 + // {PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_ENABLE, 1, 0)}, // TIM2_CH1 + // {PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 2, 1)}, // TIM1_CH2N + {PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM3_CH3 + // {PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_PARTIAL, 3, 0)}, // TIM3_CH3 + {PB_0, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 1)}, // TIM8_CH2N + {PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 3, 1)}, // TIM1_CH3N + // {PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM3_CH4 + // {PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_PARTIAL, 4, 0)}, // TIM3_CH4 + // {PB_1, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 1)}, // TIM8_CH3N + {PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_1, 2, 0)}, // TIM2_CH2 + // {PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_ENABLE, 2, 0)}, // TIM2_CH2 + {PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_PARTIAL, 1, 0)}, // TIM3_CH1 + {PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_PARTIAL, 2, 0)}, // TIM3_CH2 + {PB_6, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM4_CH1 + {PB_7, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM4_CH2 + {PB_8, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM4_CH3 +#ifdef STM32F103xG + // {PB_8, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM10_CH1 +#endif + {PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM4_CH4 +#ifdef STM32F103xG + // {PB_9, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM11_CH1 +#endif + // {PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_2, 3, 0)}, // TIM2_CH3 + {PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_ENABLE, 3, 0)}, // TIM2_CH3 + // {PB_11, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_2, 4, 0)}, // TIM2_CH4 + {PB_11, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_ENABLE, 4, 0)}, // TIM2_CH4 + {PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 1)}, // TIM1_CH1N + {PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 1)}, // TIM1_CH2N +#ifdef STM32F103xG + // {PB_14, TIM12, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM12_CH1 +#endif + {PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 1)}, // TIM1_CH3N +#ifdef STM32F103xG + // {PB_15, TIM12, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM12_CH2 +#endif + // {PC_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_ENABLE, 1, 0)}, // TIM3_CH1 + {PC_6, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM8_CH1 + // {PC_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_ENABLE, 2, 0)}, // TIM3_CH2 + {PC_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM8_CH2 + {PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_ENABLE, 3, 0)}, // TIM3_CH3 + // {PC_8, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM8_CH3 + {PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_ENABLE, 4, 0)}, // TIM3_CH4 + // {PC_9, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM8_CH4 + {PD_12, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM4_ENABLE, 1, 0)}, // TIM4_CH1 + {PD_13, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM4_ENABLE, 2, 0)}, // TIM4_CH2 + {PD_14, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM4_ENABLE, 3, 0)}, // TIM4_CH3 + {PD_15, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM4_ENABLE, 4, 0)}, // TIM4_CH4 +#ifdef STM32F103xG + {PE_5, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM9_ENABLE, 1, 0)}, // TIM9_CH1 + {PE_6, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM9_ENABLE, 2, 0)}, // TIM9_CH2 +#endif + {PE_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 1, 1)}, // TIM1_CH1N + {PE_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 1, 0)}, // TIM1_CH1 + {PE_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 2, 1)}, // TIM1_CH2N + {PE_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 2, 0)}, // TIM1_CH2 + {PE_12, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 3, 1)}, // TIM1_CH3N + {PE_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 3, 0)}, // TIM1_CH3 + {PE_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 4, 0)}, // TIM1_CH4 +#ifdef STM32F103xG + {PF_6, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM10_ENABLE, 1, 0)}, // TIM10_CH1 + {PF_7, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM11_ENABLE, 1, 0)}, // TIM11_CH1 + {PF_8, TIM13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM13_ENABLE, 1, 0)}, // TIM13_CH1 + {PF_9, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM14_ENABLE, 1, 0)}, // TIM14_CH1 +#endif + {NC, NP, 0} +}; +#endif + +//*** SERIAL *** + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_TX[] = { + {PA_2, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PB_6, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART1_ENABLE)}, + {PB_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PC_10, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + // {PC_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART3_PARTIAL)}, + {PC_12, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PD_5, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART2_ENABLE)}, + {PD_8, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART3_ENABLE)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_RX[] = { + {PA_3, USART2, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)}, + {PA_10, USART1, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)}, + {PB_7, USART1, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_USART1_ENABLE)}, + {PB_11, USART3, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)}, + {PC_11, UART4, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)}, + // {PC_11, USART3, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_USART3_PARTIAL)}, + {PD_2, UART5, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)}, + {PD_6, USART2, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_USART2_ENABLE)}, + {PD_9, USART3, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_USART3_ENABLE)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_RTS[] = { + {PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PB_14, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + // {PB_14, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART3_PARTIAL)}, + {PD_4, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART2_ENABLE)}, + {PD_12, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART3_ENABLE)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_CTS[] = { + {PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PB_13, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + // {PB_13, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART3_PARTIAL)}, + {PD_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART2_ENABLE)}, + {PD_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART3_ENABLE)}, + {NC, NP, 0} +}; +#endif + +//*** SPI *** + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_MOSI[] = { + {PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + // {PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_SPI1_ENABLE)}, + {PB_5, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_MISO[] = { + {PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + // {PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_SPI1_ENABLE)}, + {PB_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_SCLK[] = { + {PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + // {PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_SPI1_ENABLE)}, + {PB_3, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_SSEL[] = { + {PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + // {PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_SPI1_ENABLE)}, + {PA_15, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {NC, NP, 0} +}; +#endif + +//*** CAN *** + +#ifdef HAL_CAN_MODULE_ENABLED +WEAK const PinMap PinMap_CAN_RD[] = { + {PA_11, CAN1, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, AFIO_NONE)}, + {PB_8, CAN1, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, AFIO_CAN1_2)}, + {PD_0, CAN1, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, AFIO_CAN1_3)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_CAN_MODULE_ENABLED +WEAK const PinMap PinMap_CAN_TD[] = { + {PA_12, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, AFIO_NONE)}, + {PB_9, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, AFIO_CAN1_2)}, + {PD_1, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, AFIO_CAN1_3)}, + {NC, NP, 0} +}; +#endif + +//*** No ETHERNET *** + +//*** No QUADSPI *** + +//*** USB *** + +#ifdef HAL_PCD_MODULE_ENABLED +WEAK const PinMap PinMap_USB[] = { + {PA_11, USB, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, AFIO_NONE)}, // USB_DM + {PA_12, USB, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, AFIO_NONE)}, // USB_DP + {NC, NP, 0} +}; +#endif + +//*** No USB_OTG_FS *** + +//*** No USB_OTG_HS *** + +//*** SD *** + +#ifdef HAL_SD_MODULE_ENABLED +WEAK const PinMap PinMap_SD[] = { + // {PB_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D4 + // {PB_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D5 + // {PC_6, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D6 + // {PC_7, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D7 + {PC_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D0 + {PC_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D1 + {PC_10, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D2 + {PC_11, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D3 + {PC_12, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, AFIO_NONE)}, // SDIO_CK + {PD_2, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, AFIO_NONE)}, // SDIO_CMD + {NC, NP, 0} +}; +#endif diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/PinNamesVar.h b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/PinNamesVar.h new file mode 100644 index 0000000..d9076b4 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/PinNamesVar.h @@ -0,0 +1,30 @@ +/* SYS_WKUP */ +#ifdef PWR_WAKEUP_PIN1 + SYS_WKUP1 = PA_0, +#endif +#ifdef PWR_WAKEUP_PIN2 + SYS_WKUP2 = NC, +#endif +#ifdef PWR_WAKEUP_PIN3 + SYS_WKUP3 = NC, +#endif +#ifdef PWR_WAKEUP_PIN4 + SYS_WKUP4 = NC, +#endif +#ifdef PWR_WAKEUP_PIN5 + SYS_WKUP5 = NC, +#endif +#ifdef PWR_WAKEUP_PIN6 + SYS_WKUP6 = NC, +#endif +#ifdef PWR_WAKEUP_PIN7 + SYS_WKUP7 = NC, +#endif +#ifdef PWR_WAKEUP_PIN8 + SYS_WKUP8 = NC, +#endif +/* USB */ +#ifdef USBCON + USB_DM = PA_11, + USB_DP = PA_12, +#endif diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/hal_conf_custom.h b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/hal_conf_custom.h new file mode 100644 index 0000000..014943f --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/hal_conf_custom.h @@ -0,0 +1,412 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_conf_default.h + * @brief HAL default configuration file. + ****************************************************************************** + * @attention + * + * <h2><center>© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.</center></h2> + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_CONF_DEFAULT_H +#define __STM32F1xx_HAL_CONF_DEFAULT_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief Include the default list of modules to be used in the HAL driver + * and manage module deactivation + */ +#include "stm32yyxx_hal_conf.h" +#if 0 +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +#define HAL_ADC_MODULE_ENABLED +#define HAL_CAN_MODULE_ENABLED +/*#define HAL_CAN_LEGACY_MODULE_ENABLED*/ +#define HAL_CEC_MODULE_ENABLED +#define HAL_CORTEX_MODULE_ENABLED +#define HAL_CRC_MODULE_ENABLED +#define HAL_DAC_MODULE_ENABLED +#define HAL_DMA_MODULE_ENABLED +#define HAL_ETH_MODULE_ENABLED +#define HAL_EXTI_MODULE_ENABLED +#define HAL_FLASH_MODULE_ENABLED +#define HAL_GPIO_MODULE_ENABLED +#define HAL_HCD_MODULE_ENABLED +#define HAL_I2C_MODULE_ENABLED +#define HAL_I2S_MODULE_ENABLED +#define HAL_IRDA_MODULE_ENABLED +#define HAL_IWDG_MODULE_ENABLED +#define HAL_NAND_MODULE_ENABLED +#define HAL_NOR_MODULE_ENABLED +#define HAL_PCCARD_MODULE_ENABLED +#define HAL_PCD_MODULE_ENABLED +#define HAL_PWR_MODULE_ENABLED +#define HAL_RCC_MODULE_ENABLED +#define HAL_RTC_MODULE_ENABLED +#define HAL_SD_MODULE_ENABLED +#define HAL_SMARTCARD_MODULE_ENABLED +#define HAL_SPI_MODULE_ENABLED +#define HAL_SRAM_MODULE_ENABLED +#define HAL_TIM_MODULE_ENABLED +#define HAL_UART_MODULE_ENABLED +#define HAL_USART_MODULE_ENABLED +#define HAL_WWDG_MODULE_ENABLED +#define HAL_MMC_MODULE_ENABLED +#endif + +/* ########################## Oscillator Values adaptation ####################*/ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) +#if defined(USE_STM3210C_EVAL) +#define HSE_VALUE 25000000U /*!< Value of the External oscillator in Hz */ +#else +#define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */ +#endif +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) +#define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) +#define HSI_VALUE 8000000U /*!< Value of the Internal oscillator in Hz */ +#endif /* HSI_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) +#define LSI_VALUE 40000U /*!< LSI Typical Value in Hz */ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ +/** + * @brief External Low Speed oscillator (LSE) value. + * This value is used by the UART, RTC HAL module to compute the system frequency + */ +#if !defined (LSE_VALUE) +#define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) +#define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#if !defined(VDD_VALUE) +#define VDD_VALUE 3300U /*!< Value of VDD in mv */ +#endif +#if !defined (TICK_INT_PRIORITY) +#define TICK_INT_PRIORITY 0x00U /*!< tick interrupt priority */ +#endif +#if !defined (USE_RTOS) +#define USE_RTOS 0U +#endif +#if !defined (PREFETCH_ENABLE) +#define PREFETCH_ENABLE 1U +#endif + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1U */ + +/* ################## Ethernet peripheral configuration ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2U +#define MAC_ADDR1 0U +#define MAC_ADDR2 0U +#define MAC_ADDR3 0U +#define MAC_ADDR4 0U +#define MAC_ADDR5 0U + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB 8U /* 8 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ + +/* DP83848 PHY Address*/ +#define DP83848_PHY_ADDRESS 0x01U +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY 0x000000FFU +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY 0x00000FFFU + +#define PHY_READ_TO 0x0000FFFFU +#define PHY_WRITE_TO 0x0000FFFFU + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ + +#define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */ +#define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */ +#define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */ + +#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ +#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ + +#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ +#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ + +#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ +#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ +#if !defined (USE_SPI_CRC) +#define USE_SPI_CRC 0U +#endif + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED +#include "stm32f1xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED +#include "stm32f1xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_EXTI_MODULE_ENABLED +#include "stm32f1xx_hal_exti.h" +#endif /* HAL_EXTI_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED +#include "stm32f1xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED +#include "stm32f1xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED +#include "stm32f1xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED + #include "Legacy/stm32f1xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED +#include "stm32f1xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED +#include "stm32f1xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED +#include "stm32f1xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED +#include "stm32f1xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED +#include "stm32f1xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED +#include "stm32f1xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED +#include "stm32f1xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED +#include "stm32f1xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED +#include "stm32f1xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED +#include "stm32f1xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED +#include "stm32f1xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED +#include "stm32f1xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED +#include "stm32f1xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_PCCARD_MODULE_ENABLED +#include "stm32f1xx_hal_pccard.h" +#endif /* HAL_PCCARD_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED +#include "stm32f1xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED +#include "stm32f1xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED +#include "stm32f1xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED +#include "stm32f1xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED +#include "stm32f1xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED +#include "stm32f1xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED +#include "stm32f1xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED +#include "stm32f1xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED +#include "stm32f1xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED +#include "stm32f1xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED +#include "stm32f1xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_MMC_MODULE_ENABLED +#include "stm32f1xx_hal_mmc.h" +#endif /* HAL_MMC_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ +#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ +void assert_failed(uint8_t *file, uint32_t line); +#else +#define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F1xx_HAL_CONF_DEFAULT_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/ldscript.ld new file mode 100644 index 0000000..09088b6 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/ldscript.ld @@ -0,0 +1,197 @@ +/* +****************************************************************************** +** + +** File : LinkerScript.ld +** +** Author : Auto-generated by STM32CubeIDE +** +** Abstract : Linker script for STM32F103Z(C/D/E/G/GTx Device from STM32F1 series +** 256/386/512K/786/1024bytes FLASH +** 48/64/96Kbytes RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** Distribution: The file is distributed as is without any warranty +** of any kind. +** +***************************************************************************** +** @attention +** +** <h2><center>© COPYRIGHT(c) 2019 STMicroelectronics</center></h2> +** +** Redistribution and use in source and binary forms, with or without modification, +** are permitted provided that the following conditions are met: +** 1. Redistributions of source code must retain the above copyright notice, +** this list of conditions and the following disclaimer. +** 2. Redistributions in binary form must reproduce the above copyright notice, +** this list of conditions and the following disclaimer in the documentation +** and/or other materials provided with the distribution. +** 3. Neither the name of STMicroelectronics nor the names of its contributors +** may be used to endorse or promote products derived from this software +** without specific prior written permission. +** +** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE +** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE +** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL +** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR +** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER +** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, +** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE +** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20000000 + LD_MAX_DATA_SIZE; /* end of "RAM" Ram type memory */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Memories definition */ +MEMORY +{ + RAM (xrw) : ORIGIN = 0x20000000, LENGTH = LD_MAX_DATA_SIZE + FLASH (rx) : ORIGIN = 0x8000000 + LD_FLASH_OFFSET, LENGTH = LD_MAX_SIZE - LD_FLASH_OFFSET +} + +/* Sections */ +SECTIONS +{ + /* The startup code into "FLASH" Rom type memory */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data into "FLASH" Rom type memory */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data into "FLASH" Rom type memory */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { + . = ALIGN(4); + *(.ARM.extab* .gnu.linkonce.armextab.*) + . = ALIGN(4); + } >FLASH + .ARM : { + . = ALIGN(4); + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + . = ALIGN(4); + } >FLASH + + .preinit_array : + { + . = ALIGN(4); + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + . = ALIGN(4); + } >FLASH + .init_array : + { + . = ALIGN(4); + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + . = ALIGN(4); + } >FLASH + .fini_array : + { + . = ALIGN(4); + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + . = ALIGN(4); + } >FLASH + + /* Used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections into "RAM" Ram type memory */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section into "RAM" Ram type memory */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + /* Remove information from the compiler libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/variant.cpp b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/variant.cpp new file mode 100644 index 0000000..ff7ab77 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/variant.cpp @@ -0,0 +1,222 @@ +/* + ******************************************************************************* + * Copyright (c) 2019, STMicroelectronics + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ******************************************************************************* + */ + +#include "pins_arduino.h" + +#ifdef __cplusplus +extern "C" { +#endif + +// Digital PinName array +const PinName digitalPin[] = { + PA_0, //D0 + PA_1, //D1 + PA_2, //D2 + PA_3, //D3 + PA_4, //D4 + PA_5, //D5 + PA_6, //D6 + PA_7, //D7 + PA_8, //D8 + PA_9, //D9 + PA_10, //D10 + PA_11, //D11 + PA_12, //D12 + PA_13, //D13 + PA_14, //D14 + PA_15, //D15 + + PB_0, //D16 + PB_1, //D17 + PB_2, //D18 + PB_3, //D19 + PB_4, //D20 + PB_5, //D21 + PB_6, //D22 + PB_7, //D23 + PB_8, //D24 + PB_9, //D25 + PB_10, //D26 + PB_11, //D27 + PB_12, //D28 + PB_13, //D29 + PB_14, //D30 + PB_15, //D31 + + PC_0, //D32 + PC_1, //D33 + PC_2, //D34 + PC_3, //D35 + PC_4, //D36 + PC_5, //D37 + PC_6, //D38 + PC_7, //D39 + PC_8, //D40 + PC_9, //D41 + PC_10, //D42 + PC_11, //D43 + PC_12, //D44 + PC_13, //D45 + PC_14, //D46 + PC_15, //D47 + + PD_0, //D48 + PD_1, //D49 + PD_2, //D50 + PD_3, //D51 + PD_4, //D52 + PD_5, //D53 + PD_6, //D54 + PD_7, //D55 + PD_8, //D56 + PD_9, //D57 + PD_10, //D58 + PD_11, //D59 + PD_12, //D60 + PD_13, //D61 + PD_14, //D62 + PD_15, //D63 + + PE_0, //D64 + PE_1, //D65 + PE_2, //D66 + PE_3, //D67 + PE_4, //D68 + PE_5, //D69 + PE_6, //D70 + PE_7, //D71 + PE_8, //D72 + PE_9, //D73 + PE_10, //D74 + PE_11, //D75 + PE_12, //D76 + PE_13, //D77 + PE_14, //D78 + PE_15, //D79 + + PF_0, //D80 + PF_1, //D81 + PF_2, //D82 + PF_3, //D83 + PF_4, //D84 + PF_5, //D85 + PF_6, //D86 + PF_7, //D87 + PF_8, //D88 + PF_9, //D89 + PF_10, //D90 + PF_11, //D91 + PF_12, //D92 + PF_13, //D93 + PF_14, //D94 + PF_15, //D95 + + PG_0, //D96 + PG_1, //D97 + PG_2, //D98 + PG_3, //D99 + PG_4, //D100 + PG_5, //D101 + PG_6, //D102 + PG_7, //D103 + PG_8, //D104 + PG_9, //D105 + PG_10, //D106 + PG_11, //D107 + PG_12, //D108 + PG_13, //D109 + PG_14, //D110 + PG_15 //D111 +}; + +// Analog (Ax) pin number array +const uint32_t analogInputPin[] = { + 0, // A0, PA0 + 1, // A1, PA1 + 2, // A2, PA2 + 3, // A3, PA3 + 4, // A4, PA4 + 5, // A5, PA5 + 6, // A6, PA6 + 7, // A7, PA7 + 16, // A8, PB0 + 17, // A9, PB1 + 32, // A10, PC0 + 33, // A11, PC1 + 34, // A12, PC2 + 35, // A13, PC3 + 36, // A14, PC4 + 37, // A15, PC5 + 86, // A16, PF6 + 87, // A17, PF7 + 88, // A18, PF8 + 89, // A19, PF9 + 90 // A20, PF10 +}; + +#ifdef __cplusplus +} +#endif + +// ---------------------------------------------------------------------------- + +#ifdef __cplusplus +extern "C" { +#endif + +/** + * @brief System Clock Configuration + * @param None + * @retval None + */ +WEAK void SystemClock_Config(void) +{ + RCC_OscInitTypeDef RCC_OscInitStruct = {}; + RCC_ClkInitTypeDef RCC_ClkInitStruct = {}; + RCC_PeriphCLKInitTypeDef PeriphClkInit = {}; + + /* Initializes the CPU, AHB and APB busses clocks */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1; + RCC_OscInitStruct.HSIState = RCC_HSI_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9; + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { + Error_Handler(); + } + /* Initializes the CPU, AHB and APB busses clocks */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK + | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; + + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) { + Error_Handler(); + } + + PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC | RCC_PERIPHCLK_USB; + PeriphClkInit.AdcClockSelection = RCC_ADCPCLK2_DIV6; + PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_PLL_DIV1_5; + if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK) { + Error_Handler(); + } +} + + +#ifdef __cplusplus +} +#endif diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/variant.h b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/variant.h new file mode 100644 index 0000000..fb878f8 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/variant.h @@ -0,0 +1,232 @@ +/* + ******************************************************************************* + * Copyright (c) 2019, STMicroelectronics + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ******************************************************************************* + */ + +#ifndef _VARIANT_ARDUINO_STM32_ +#define _VARIANT_ARDUINO_STM32_ + +#ifdef __cplusplus +extern "C" { +#endif // __cplusplus + +/*---------------------------------------------------------------------------- + * Pins + *----------------------------------------------------------------------------*/ +#define PA0 0 +#define PA1 1 +#define PA2 2 +#define PA3 3 +#define PA4 4 +#define PA5 5 +#define PA6 6 +#define PA7 7 +#define PA8 8 +#define PA9 9 +#define PA10 10 +#define PA11 11 +#define PA12 12 +#define PA13 13 +#define PA14 14 +#define PA15 15 + +#define PB0 16 +#define PB1 17 +#define PB2 18 +#define PB3 19 +#define PB4 20 +#define PB5 21 +#define PB6 22 +#define PB7 23 +#define PB8 24 +#define PB9 25 +#define PB10 26 +#define PB11 27 +#define PB12 28 +#define PB13 29 +#define PB14 30 +#define PB15 31 + +#define PC0 32 +#define PC1 33 +#define PC2 34 +#define PC3 35 +#define PC4 36 +#define PC5 37 +#define PC6 38 +#define PC7 39 +#define PC8 40 +#define PC9 41 +#define PC10 42 +#define PC11 43 +#define PC12 44 +#define PC13 45 +#define PC14 46 +#define PC15 47 + +#define PD0 48 +#define PD1 49 +#define PD2 50 +#define PD3 51 +#define PD4 52 +#define PD5 53 +#define PD6 54 +#define PD7 55 +#define PD8 56 +#define PD9 57 +#define PD10 58 +#define PD11 59 +#define PD12 60 +#define PD13 61 +#define PD14 62 +#define PD15 63 + +#define PE0 64 +#define PE1 65 +#define PE2 66 +#define PE3 67 +#define PE4 68 +#define PE5 69 +#define PE6 70 +#define PE7 71 +#define PE8 72 +#define PE9 73 +#define PE10 74 +#define PE11 75 +#define PE12 76 +#define PE13 77 +#define PE14 78 +#define PE15 79 + +#define PF0 80 +#define PF1 81 +#define PF2 82 +#define PF3 83 +#define PF4 84 +#define PF5 85 +#define PF6 86 +#define PF7 87 +#define PF8 88 +#define PF9 89 +#define PF10 90 +#define PF11 91 +#define PF12 92 +#define PF13 93 +#define PF14 94 +#define PF15 95 + +#define PG0 96 +#define PG1 97 +#define PG2 98 +#define PG3 99 +#define PG4 100 +#define PG5 101 +#define PG6 102 +#define PG7 103 +#define PG8 104 +#define PG9 105 +#define PG10 106 +#define PG11 107 +#define PG12 108 +#define PG13 109 +#define PG14 110 +#define PG15 111 + +// This must be a literal +#define NUM_DIGITAL_PINS 112 +#define NUM_ANALOG_INPUTS 21 + +// On-board LED pin number +#ifdef ARDUINO_VCCGND_F103ZET6_MINI +#define LED_BUILTIN PG15 +#elif defined(ARDUINO_VCCGND_F103ZET6) +#define LED_BUILTIN PC13 +#elif !defined(LED_BUILTIN) +#define LED_BUILTIN PC13 +#endif + +// On-board user button +#ifndef USER_BTN +#define USER_BTN PB1 +#endif + +// SPI Definitions +#ifdef ARDUINO_VCCGND_F103ZET6 +#define PIN_SPI_SS PA15 +#define PIN_SPI_MOSI PB5 +#define PIN_SPI_MISO PB4 +#define PIN_SPI_SCK PB3 +#else +#define PIN_SPI_SS PC4 +#define PIN_SPI_MOSI PA7 +#define PIN_SPI_MISO PA6 +#define PIN_SPI_SCK PA5 +#endif + +// I2C Definitions +#define PIN_WIRE_SDA PB7 +#define PIN_WIRE_SCL PB6 + +// Timer Definitions (optional) +// Use TIM6/TIM7 when possible as servo and tone don't need GPIO output pin +#define TIMER_TONE TIM6 +#define TIMER_SERVO TIM7 + +// UART Definitions +// Define here Serial instance number to map on Serial generic name +#define SERIAL_UART_INSTANCE 1 + +// Default pin used for 'Serial' instance (ex: ST-Link) +// Mandatory for Firmata +#define PIN_SERIAL_RX PA10 +#define PIN_SERIAL_TX PA9 + +// Default pin used for 'Serial2' instance +#define PIN_SERIAL2_RX PA3 +#define PIN_SERIAL2_TX PA2 + +// Default pin used for 'Serial3' instance +#define PIN_SERIAL3_RX PB11 +#define PIN_SERIAL3_TX PB10 + +/* Extra HAL modules */ +#define HAL_DAC_MODULE_ENABLED +#define HAL_SD_MODULE_ENABLED +#define HAL_SRAM_MODULE_ENABLED + +#ifdef __cplusplus +} // extern "C" +#endif +/*---------------------------------------------------------------------------- + * Arduino objects - C++ only + *----------------------------------------------------------------------------*/ + +#ifdef __cplusplus + // These serial port names are intended to allow libraries and architecture-neutral + // sketches to automatically default to the correct port name for a particular type + // of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN, + // the first hardware serial port whose RX/TX pins are not dedicated to another use. + // + // SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor + // + // SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial + // + // SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library + // + // SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins. + // + // SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX + // pins are NOT connected to anything by default. + #define SERIAL_PORT_MONITOR Serial + #define SERIAL_PORT_HARDWARE Serial1 +#endif + +#endif /* _VARIANT_ARDUINO_STM32_ */ |