diff options
Diffstat (limited to 'buildroot/share/PlatformIO/variants/STEVAL_F401VE')
6 files changed, 1627 insertions, 0 deletions
diff --git a/buildroot/share/PlatformIO/variants/STEVAL_F401VE/PeripheralPins.c b/buildroot/share/PlatformIO/variants/STEVAL_F401VE/PeripheralPins.c new file mode 100644 index 0000000..5335361 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/STEVAL_F401VE/PeripheralPins.c @@ -0,0 +1,274 @@ + +/* + ******************************************************************************* + * Copyright (c) 2019, STMicroelectronics + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ******************************************************************************* + * Automatically generated from STM32F401V(D-E)Tx.xml + */ +#include "Arduino.h" +#include "PeripheralPins.h" + +/* ===== + * Note: Commented lines are alternative possibilities which are not used per default. + * If you change them, you will have to know what you do + * ===== + */ + +//*** ADC *** + +#ifdef HAL_ADC_MODULE_ENABLED +WEAK const PinMap PinMap_ADC[] = { + {PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 + {PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 + {PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 + {PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 + // {PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4 + // {PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5 + // {PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 + // {PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 + // {PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 + // {PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9 + // {PC_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10 + // {PC_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11 + {PC_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12 + {PC_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13 + // {PC_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14 + // {PC_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15 + {NC, NP, 0} +}; +#endif + +//*** No DAC *** + +//*** I2C *** + +#ifdef HAL_I2C_MODULE_ENABLED +WEAK const PinMap PinMap_I2C_SDA[] = { + // {PB_3, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C2)}, + // {PB_4, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C3)}, + {PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + // {PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + // {PC_9, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_I2C_MODULE_ENABLED +WEAK const PinMap PinMap_I2C_SCL[] = { + // {PA_8, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)}, + {PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + // {PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + // {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)}, + {NC, NP, 0} +}; +#endif + +//*** PWM *** + +#ifdef HAL_TIM_MODULE_ENABLED +WEAK const PinMap PinMap_PWM[] = { + // {PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 + // {PA_0, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 1, 0)}, // TIM5_CH1 + // {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2 + // {PA_1, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 2, 0)}, // TIM5_CH2 + // {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3 + // {PA_2, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 3, 0)}, // TIM5_CH3 + // {PA_2, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1 + // {PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4 + // {PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 4, 0)}, // TIM5_CH4 + // {PA_3, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2 + // {PA_5, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 + // {PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 + // {PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N + // {PA_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 + // {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1 + // {PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 + // {PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 + // {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4 + // {PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 + // {PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N + {PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3 + // {PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N + {PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4 + // {PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2 + // {PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 + // {PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 + // {PB_6, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1 + // {PB_7, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2 + // {PB_8, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3 + // {PB_8, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1 + // {PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4 + // {PB_9, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1 + {PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3 + // {PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N + // {PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N + // {PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N + {PC_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 + {PC_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 + // {PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3 + // {PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4 + {PD_12, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1 + {PD_13, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2 + {PD_14, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3 + {PD_15, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4 + {PE_5, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1 + // {PE_6, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2 + // {PE_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N + // {PE_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1 + // {PE_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N + // {PE_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 + // {PE_12, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N + // {PE_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 + {PE_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4 + {NC, NP, 0} +}; +#endif + +//*** SERIAL *** + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_TX[] = { + // {PA_2, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + // {PA_11, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + // {PB_6, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + // {PC_6, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + {PD_5, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_RX[] = { + // {PA_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PA_10, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + // {PA_12, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + // {PB_7, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + // {PC_7, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + {PD_6, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_RTS[] = { + // {PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + // {PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PD_4, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_CTS[] = { + // {PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + // {PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PD_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {NC, NP, 0} +}; +#endif + +//*** SPI *** + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_MOSI[] = { + {PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PB_5, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + // {PC_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + // {PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + // {PD_6, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PE_6, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)}, + // {PE_14, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_MISO[] = { + {PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PB_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + // {PC_2, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + // {PC_11, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + // {PE_5, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)}, + // {PE_13, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_SCLK[] = { + {PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PB_3, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + // {PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + // {PC_10, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + // {PD_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + // {PE_2, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)}, + // {PE_12, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_SSEL[] = { + {PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PA_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + // {PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PA_15, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + // {PB_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + // {PE_4, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)}, + // {PE_11, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)}, + {NC, NP, 0} +}; +#endif + +//*** No CAN *** + +//*** No ETHERNET *** + +//*** No QUADSPI *** + +//*** USB *** + +#ifdef HAL_PCD_MODULE_ENABLED +WEAK const PinMap PinMap_USB_OTG_FS[] = { + // {PA_8, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_SOF + // {PA_9, USB_OTG_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_OTG_FS_VBUS + // {PA_10, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_ID + {PA_11, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DM + {PA_12, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DP + {NC, NP, 0} +}; +#endif + +//*** No USB_OTG_HS *** +//*** SD *** + +#ifdef HAL_SD_MODULE_ENABLED +WEAK const PinMap PinMap_SD[] = { + // {PB_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D4 + // {PB_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D5 + // {PC_6, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D6 + // {PC_7, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D7 + {PC_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D0 + {PC_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D1 + {PC_10, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D2 + {PC_11, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D3 + {PC_12, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CK + {PD_2, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CMD + {NC, NP, 0} +}; +#endif diff --git a/buildroot/share/PlatformIO/variants/STEVAL_F401VE/PinNamesVar.h b/buildroot/share/PlatformIO/variants/STEVAL_F401VE/PinNamesVar.h new file mode 100644 index 0000000..6a1eb9b --- /dev/null +++ b/buildroot/share/PlatformIO/variants/STEVAL_F401VE/PinNamesVar.h @@ -0,0 +1,33 @@ +/* SYS_WKUP */ +#ifdef PWR_WAKEUP_PIN1 + SYS_WKUP1 = PA_0, +#endif +#ifdef PWR_WAKEUP_PIN2 + SYS_WKUP2 = NC, +#endif +#ifdef PWR_WAKEUP_PIN3 + SYS_WKUP3 = NC, +#endif +#ifdef PWR_WAKEUP_PIN4 + SYS_WKUP4 = NC, +#endif +#ifdef PWR_WAKEUP_PIN5 + SYS_WKUP5 = NC, +#endif +#ifdef PWR_WAKEUP_PIN6 + SYS_WKUP6 = NC, +#endif +#ifdef PWR_WAKEUP_PIN7 + SYS_WKUP7 = NC, +#endif +#ifdef PWR_WAKEUP_PIN8 + SYS_WKUP8 = NC, +#endif +/* USB */ +#ifdef USBCON + USB_OTG_FS_SOF = PA_8, + USB_OTG_FS_VBUS = PA_9, + USB_OTG_FS_ID = PA_10, + USB_OTG_FS_DM = PA_11, + USB_OTG_FS_DP = PA_12, +#endif diff --git a/buildroot/share/PlatformIO/variants/STEVAL_F401VE/hal_conf_custom.h b/buildroot/share/PlatformIO/variants/STEVAL_F401VE/hal_conf_custom.h new file mode 100644 index 0000000..0c77819 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/STEVAL_F401VE/hal_conf_custom.h @@ -0,0 +1,496 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_conf.h + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + * <h2><center>© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.</center></h2> + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F4xx_HAL_CONF_CUSTOM +#define __STM32F4xx_HAL_CONF_CUSTOM + +#ifdef __cplusplus +extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ + /** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +#define HAL_ADC_MODULE_ENABLED +/* #define HAL_CAN_MODULE_ENABLED */ +/* #define HAL_CAN_LEGACY_MODULE_ENABLED */ +#define HAL_CRC_MODULE_ENABLED +/* #define HAL_CEC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +//#define HAL_DAC_MODULE_ENABLED +/* #define HAL_DCMI_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +/* #define HAL_DMA2D_MODULE_ENABLED */ +/* #define HAL_ETH_MODULE_ENABLED */ +#define HAL_FLASH_MODULE_ENABLED +/* #define HAL_NAND_MODULE_ENABLED */ +/* #define HAL_NOR_MODULE_ENABLED */ +/* #define HAL_PCCARD_MODULE_ENABLED */ +/* #define HAL_SRAM_MODULE_ENABLED */ +/* #define HAL_SDRAM_MODULE_ENABLED */ +/* #define HAL_HASH_MODULE_ENABLED */ +#define HAL_GPIO_MODULE_ENABLED +/* #define HAL_EXTI_MODULE_ENABLED */ +#define HAL_I2C_MODULE_ENABLED +/* #define HAL_SMBUS_MODULE_ENABLED */ +/* #define HAL_I2S_MODULE_ENABLED */ +#define HAL_IWDG_MODULE_ENABLED +/* #define HAL_LTDC_MODULE_ENABLED */ +/* #define HAL_DSI_MODULE_ENABLED */ +#define HAL_PWR_MODULE_ENABLED +/* #define HAL_QSPI_MODULE_ENABLED */ +#define HAL_RCC_MODULE_ENABLED +/* #define HAL_RNG_MODULE_ENABLED */ +#define HAL_RTC_MODULE_ENABLED +/* #define HAL_SAI_MODULE_ENABLED */ +#define HAL_SD_MODULE_ENABLED +#define HAL_SPI_MODULE_ENABLED +#define HAL_TIM_MODULE_ENABLED +/* #define HAL_UART_MODULE_ENABLED */ +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +#ifndef HAL_PCD_MODULE_ENABLED + #define HAL_PCD_MODULE_ENABLED //Since STM32 v3.10700.191028 this is automatically added if any type of USB is enabled (as in Arduino IDE) +#endif +/* #define HAL_HCD_MODULE_ENABLED */ +/* #define HAL_FMPI2C_MODULE_ENABLED */ +/* #define HAL_SPDIFRX_MODULE_ENABLED */ +/* #define HAL_DFSDM_MODULE_ENABLED */ +/* #define HAL_LPTIM_MODULE_ENABLED */ +/* #define HAL_MMC_MODULE_ENABLED */ + +/* ########################## HSE/HSI Values adaptation ##################### */ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#ifndef HSE_VALUE +#define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#ifndef HSE_STARTUP_TIMEOUT +#define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#ifndef HSI_VALUE +#define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz */ +#endif /* HSI_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#ifndef LSI_VALUE +#define LSI_VALUE 32000U /*!< LSI Typical Value in Hz */ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz +The real value may vary depending on the variations +in voltage and temperature. */ +/** + * @brief External Low Speed oscillator (LSE) value. + */ +#ifndef LSE_VALUE +#define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +#ifndef LSE_STARTUP_TIMEOUT +#define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#ifndef EXTERNAL_CLOCK_VALUE +#define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External oscillator in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#if !defined (VDD_VALUE) +#define VDD_VALUE 3300U /*!< Value of VDD in mv */ +#endif +#if !defined (TICK_INT_PRIORITY) +#define TICK_INT_PRIORITY 0x00U /*!< tick interrupt priority */ +#endif +#if !defined (USE_RTOS) +#define USE_RTOS 0U +#endif +#if !defined (PREFETCH_ENABLE) +#define PREFETCH_ENABLE 1U +#endif +#if !defined (INSTRUCTION_CACHE_ENABLE) +#define INSTRUCTION_CACHE_ENABLE 1U +#endif +#if !defined (DATA_CACHE_ENABLE) +#define DATA_CACHE_ENABLE 1U +#endif + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ +#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ +#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ +#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U /* FMPI2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ +#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ +#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ +#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ +#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1U */ + +/* ################## Ethernet peripheral configuration ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2U +#define MAC_ADDR1 0U +#define MAC_ADDR2 0U +#define MAC_ADDR3 0U +#define MAC_ADDR4 0U +#define MAC_ADDR5 0U + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ + +/* DP83848_PHY_ADDRESS Address*/ +#define DP83848_PHY_ADDRESS 0x01U +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY 0x000000FFU +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY 0x00000FFFU + +#define PHY_READ_TO 0x0000FFFFU +#define PHY_WRITE_TO 0x0000FFFFU + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ +#define PHY_SR ((uint16_t)0x10U) /*!< PHY status register Offset */ + +#define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver + * Activated: CRC code is present inside driver + * Deactivated: CRC code cleaned from driver + */ +#ifndef USE_SPI_CRC +#define USE_SPI_CRC 0U +#endif + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED +#include "stm32f4xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED +#include "stm32f4xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_EXTI_MODULE_ENABLED +#include "stm32f4xx_hal_exti.h" +#endif /* HAL_EXTI_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED +#include "stm32f4xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED +#include "stm32f4xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED +#include "stm32f4xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED +#include "stm32f4xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED +#include "stm32f4xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED +#include "stm32f4xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED +#include "stm32f4xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED +#include "stm32f4xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED +#include "stm32f4xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED +#include "stm32f4xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED +#include "stm32f4xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED +#include "stm32f4xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED +#include "stm32f4xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED +#include "stm32f4xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED +#include "stm32f4xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_PCCARD_MODULE_ENABLED +#include "stm32f4xx_hal_pccard.h" +#endif /* HAL_PCCARD_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED +#include "stm32f4xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED +#include "stm32f4xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED +#include "stm32f4xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED +#include "stm32f4xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED +#include "stm32f4xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED +#include "stm32f4xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED +#include "stm32f4xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED +#include "stm32f4xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED +#include "stm32f4xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED +#include "stm32f4xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED +#include "stm32f4xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED +#include "stm32f4xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED +#include "stm32f4xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED +#include "stm32f4xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED +#include "stm32f4xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED +#include "stm32f4xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED +#include "stm32f4xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED +#include "stm32f4xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED +#include "stm32f4xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED +#include "stm32f4xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED +#include "stm32f4xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED +#include "stm32f4xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED +#include "stm32f4xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED +#include "stm32f4xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_FMPI2C_MODULE_ENABLED +#include "stm32f4xx_hal_fmpi2c.h" +#endif /* HAL_FMPI2C_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED +#include "stm32f4xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED +#include "stm32f4xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED +#include "stm32f4xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_MMC_MODULE_ENABLED +#include "stm32f4xx_hal_mmc.h" +#endif /* HAL_MMC_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ +#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ +void assert_failed(uint8_t *file, uint32_t line); +#else +#define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F4xx_HAL_CONF_CUSTOM_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/buildroot/share/PlatformIO/variants/STEVAL_F401VE/ldscript.ld b/buildroot/share/PlatformIO/variants/STEVAL_F401VE/ldscript.ld new file mode 100644 index 0000000..f20a047 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/STEVAL_F401VE/ldscript.ld @@ -0,0 +1,187 @@ +/* +***************************************************************************** +** +** File : ldscript.ld +** +** Abstract : Linker script for STM32F401RETx Device with +** 512KByte FLASH, 96KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +***************************************************************************** +** @attention +** +** <h2><center>© COPYRIGHT(c) 2014 Ac6</center></h2> +** +** Redistribution and use in source and binary forms, with or without modification, +** are permitted provided that the following conditions are met: +** 1. Redistributions of source code must retain the above copyright notice, +** this list of conditions and the following disclaimer. +** 2. Redistributions in binary form must reproduce the above copyright notice, +** this list of conditions and the following disclaimer in the documentation +** and/or other materials provided with the distribution. +** 3. Neither the name of Ac6 nor the names of its contributors +** may be used to endorse or promote products derived from this software +** without specific prior written permission. +** +** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE +** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE +** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL +** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR +** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER +** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, +** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE +** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20018000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 512K +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 96K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(4); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(4); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} + + diff --git a/buildroot/share/PlatformIO/variants/STEVAL_F401VE/variant.cpp b/buildroot/share/PlatformIO/variants/STEVAL_F401VE/variant.cpp new file mode 100644 index 0000000..4ecbff0 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/STEVAL_F401VE/variant.cpp @@ -0,0 +1,310 @@ +/* + ******************************************************************************* + * Copyright (c) 2017, STMicroelectronics + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + ******************************************************************************* + */ + +#include "pins_arduino.h" + +#ifdef __cplusplus +extern "C" { +#endif + +#ifdef ARDUINO_STEVAL +// Pin number +// This array allows to wrap Arduino pin number(Dx or x) +// to STM32 PinName (PX_n) +const PinName digitalPin[] = { + PA_9, // TX + PA_10, // RX + + // WIFI + PD_3, // CTS + PD_4, // RTS + PD_5, // TX + PD_6, // RX + PB_5, // WIFI_WAKEUP + PE_11, // WIFI_RESET + PE_12, // WIFI_BOOT + + // STATUS_LED + PE_1, //STATUS_LED + + // SPI USER + PB_12, // SPI_CS + PB_15, // SPI_MOSI + PB_14, // SPI_MISO + PB_13, // SPI_SCK + + // I2C USER + PB_7, // SDA + PB_6, // SCL + + // SPI + PA_4, // SPI_CS + PA_5, // SPI_SCK + PA_6, // SPI_MISO + PA_7, // SPI_MOSI + + // JTAG + PA_13, // JTAG_TMS/SWDIO + PA_14, // JTAG_TCK/SWCLK + PB_3, // JTAG_TDO/SWO + + // SDCARD + PC_8, // SDIO_D0 + PC_9, // SDIO_D1 + PA_15, // SD_CARD_DETECT + PC_10, // SDIO_D2 + PC_11, // SDIO_D3 + PC_12, // SDIO_CK + PD_2, // SDIO_CMD + + // OTG + PA_11, // OTG_DM + PA_12, // OTG_DP + + // IR/PROBE + PD_1, // IR_OUT + PC_1, // IR_ON + + // USER_PINS + PD_7, // USER3 + PB_9, // USER1 + PE_0, // USER2 + PB_4, // USER4 + + // USERKET + PE_7, // USER_BUTTON + + // ENDSTOPS + PD_8, // X_STOP + PD_9, // Y_STOP + PD_10, // Z_STOP + PD_11, // U_STOP + PA_8, // V_STOP + PD_0, // W_STOP + + // HEATERS + PD_13, // BED_HEAT_2 + PD_14, // BED_HEAT_1 + PD_15, // BED_HEAT_3 + PC_7, // E1_HEAT_PWM + PB_0, // E2_HEAT_PWM + PB_1, // E3_HEAT_PWM + + // THERMISTOR + PC_2, // BED_THERMISTOR_1 + PC_3, // BED_THERMISTOR_2 + PA_3, // BED_THERMISTOR_3 + PA_0, // E1_THERMISTOR + PA_1, // E2_THERMISTOR + PA_2, // E3_THERMISTOR + + // FANS + PC_4, // E1_FAN + PC_5, // E2_FAN + PE_8, // E3_FAN + + // X_MOTOR + PE_13, // X_RESET + PE_14, // X_PWM + PE_15, // X_DIR + + // Y_MOTOR + PE_10, // Y_RESET + PB_10, // Y_PWM + PE_9, // Y_DIR + + // Z_MOTOR + PC_15, // Z_RESET + PC_6, // Z_PWM + PC_0, // Z_DIR + + // E1_MOTOR + PC_14, // E1_RESET + PC_13, // E1_DIR + PD_12, // E1_PWM + + // E2_MOTOR + PE_4, // E2_RESET + PE_5, // E2_PWM + PE_6, // E2_DIR + + // E3_MOTOR + PE_3, // E3_RESET + PE_2, // E3_DIR + PB_8 // E3_PWM +}; +#endif + +#ifdef __cplusplus +} +#endif + +// ---------------------------------------------------------------------------- + +#ifdef __cplusplus +extern "C" { +#endif +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (HSI) + * SYSCLK(Hz) = 84000000 + * HCLK(Hz) = 84000000 + * AHB Prescaler = 1 + * APB1 Prescaler = 2 + * APB2 Prescaler = 1 + * HSI Frequency(Hz) = 16000000 + * PLL_M = 16 + * PLL_N = 336 + * PLL_P = 4 + * PLL_Q = 7 + * VDD(V) = 3.3 + * Main regulator output voltage = Scale2 mode + * Flash Latency(WS) = 2 + * @param None + * @retval None + */ +WEAK void SystemClock_Config(void) +{ + RCC_OscInitTypeDef RCC_OscInitStruct = {}; + RCC_ClkInitTypeDef RCC_ClkInitStruct = {}; + + /* Configure the main internal regulator output voltage */ + __HAL_RCC_PWR_CLK_ENABLE(); + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2); + + /* Initializes the CPU, AHB and APB busses clocks */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = 15; + RCC_OscInitStruct.PLL.PLLN = 144; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; + RCC_OscInitStruct.PLL.PLLQ = 5; + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { + Error_Handler(); + } + /* Initializes the CPU, AHB and APB busses clocks */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK + | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; + + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK) { + Error_Handler(); + } +} + +#ifdef __cplusplus +} +#endif + + +// PA_0 54 // E1_THERMISTOR +// PA_1 55 // E2_THERMISTOR +// PA_2 56 // E3_THERMISTOR +// PA_3 53 // BED_THERMISTOR_3 +// PA_4 16 // SPI_CS +// PA_5 17 // SPI_SCK +// PA_6 18 // SPI_MISO +// PA_7 19 // SPI_MOSI +// PA_8 43 // V_STOP +// PA_9 0 //TX +// PA_10 1 //RX +// PA_11 30 //OTG_DM +// PA_12 31 //OTG_DP +// PA_13 20 // JTAG_TMS/SWDIO +// PA_14 21 // JTAG_TCK/SWCLK +// PA_15 25 // SD_CARD_DETECT +// PB_0 49 // E2_HEAT_PWM +// PB_1 50 // E3_HEAT_PWM +// PB_3 22 // JTAG_TDO/SWO +// PB_4 37 // USER4 +// PB_5 6 // WIFI_WAKEUP +// PB_6 15 // SCL +// PB_7 14 // SDA +// PB_8 77 // E3_PWM +// PB_9 35 // USER1 +// PB_10 64 // Y_PWM +// PB_12 10 // SPI_CS +// PB_13 13 // SPI_SCK +// PB_14 12 // SPI_MISO +// PB_15 11 // SPI_MOSI +// PC_0 68 // Z_DIR +// PC_1 33 //IR_ON +// PC_2 51 // BED_THERMISTOR_1 +// PC_3 52 // BED_THERMISTOR_2 +// PC_4 57 // E1_FAN +// PC_5 58 // E2_FAN +// PC_6 67 // Z_PWM +// PC_7 48 // E1_HEAT_PWM +// PC_8 23 // SDIO_D0 +// PC_9 24 // SDIO_D1 +// PC_10 26 // SDIO_D2 +// PC_11 27 // SDIO_D3 +// PC_12 28 // SDIO_CK +// PC_13 70 // E1_DIR +// PC_14 69 // E1_RESET +// PC_15 66 // Z_RESET +// PD_0 44 // W_STOP +// PD_1 32 //IR_OUT +// PD_2 29 // SDIO_CMD +// PD_3 2 // CTS +// PD_4 3 // RTS +// PD_5 4 // TX +// PD_6 5 // RX +// PD_7 34 // USER3 +// PD_8 39 // X_STOP +// PD_9 40 // Y_STOP +// PD_10 41 // Z_STOP +// PD_11 42 // U_STOP +// PD_12 71 // E1_PWM +// PD_13 45 // BED_HEAT_2 +// PD_14 46 // BED_HEAT_1 +// PD_15 47 // BED_HEAT_3 +// PE_0 36 // USER2 +// PE_1 9 // STATUS_LED +// PE_2 76 // E3_DIR +// PE_3 75 // E3_RESET +// PE_4 72 // E2_RESET +// PE_5 73 // E2_PWM +// PE_6 74 // E2_DIR +// PE_7 38 // USER_BUTTON +// PE_8 59 // E3_FAN +// PE_9 65 // Y_DIR +// PE_10 63 // Y_RESET +// PE_11 7 // WIFI_RESET +// PE_12 8 // WIFI_BOOT +// PE_13 60 // X_RESET +// PE_14 61 // X_PWM +// PE_15 62 // X_DIR diff --git a/buildroot/share/PlatformIO/variants/STEVAL_F401VE/variant.h b/buildroot/share/PlatformIO/variants/STEVAL_F401VE/variant.h new file mode 100644 index 0000000..df7295a --- /dev/null +++ b/buildroot/share/PlatformIO/variants/STEVAL_F401VE/variant.h @@ -0,0 +1,327 @@ +/* + ******************************************************************************* + * Copyright (c) 2017, STMicroelectronics + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + ******************************************************************************* + */ + +#ifndef _VARIANT_ARDUINO_STM32_ +#define _VARIANT_ARDUINO_STM32_ +/*---------------------------------------------------------------------------- + * Headers + *----------------------------------------------------------------------------*/ + +#ifdef __cplusplus +extern "C" { +#endif // __cplusplus + +/*---------------------------------------------------------------------------- + * Pins + *----------------------------------------------------------------------------*/ +#ifdef ARDUINO_STEVAL + + +/*---------------------------------------------------------------------------- + * Pins + *----------------------------------------------------------------------------*/ +// USART1_MAIN +#define PA9 0 //TX +#define PA10 1 //RX + +// WIFI (USART2) +#define PD3 2 // CTS +#define PD4 3 // RTS +#define PD5 4 // TX +#define PD6 5 // RX +#define PB5 6 // WIFI_WAKEUP +#define PE11 7 // WIFI_RESET +#define PE12 8 // WIFI_BOOT + +// STATUS_LED +#define PE1 9 // STATUS_LED + +// SPI USER +#define PB12 10 // SPI_CS +#define PB15 11 // SPI_MOSI +#define PB14 12 // SPI_MISO +#define PB13 13 // SPI_SCK + +// I2C USER +#define PB7 14 // SDA +#define PB6 15 // SCL + +// SPI +#define PA4 16 // SPI_CS +#define PA5 17 // SPI_SCK +#define PA6 18 // SPI_MISO +#define PA7 19 // SPI_MOSI + +// JTAG +#define PA13 20 // JTAG_TMS/SWDIO +#define PA14 21 // JTAG_TCK/SWCLK +#define PB3 22 // JTAG_TDO/SWO + +// SDCARD +#define PC8 23 // SDIO_D0 +#define PC9 24 // SDIO_D1 +#define PA15 25 // SD_CARD_DETECT +#define PC10 26 // SDIO_D2 +#define PC11 27 // SDIO_D3 +#define PC12 28 // SDIO_CK +#define PD2 29 // SDIO_CMD + +// OTG +#define PA11 30 //OTG_DM +#define PA12 31 //OTG_DP + +// IR/PROBE +#define PD1 32 //IR_OUT +#define PC1 33 //IR_ON + +// USER_PINS +#define PD7 34 // USER3 +#define PB9 35 // USER1 +#define PE0 36 // USER2 +#define PB4 37 // USER4 + +// USERKET +#define PE7 38 // USER_BUTTON + +// ENDSTOPS +#define PD8 39 // X_STOP +#define PD9 40 // Y_STOP +#define PD10 41 // Z_STOP +#define PD11 42 // U_STOP +#define PA8 43 // V_STOP +#define PD0 44 // W_STOP + +// HEATERS +#define PD13 45 // BED_HEAT_2 +#define PD14 46 // BED_HEAT_1 +#define PD15 47 // BED_HEAT_3 +#define PC7 48 // E1_HEAT_PWM +#define PB0 49 // E2_HEAT_PWM +#define PB1 50 // E3_HEAT_PWM + +// THERMISTOR +#define PC2 51 // BED_THERMISTOR_1 +#define PC3 52 // BED_THERMISTOR_2 +#define PA3 53 // BED_THERMISTOR_3 +#define PA0 54 // E1_THERMISTOR +#define PA1 55 // E2_THERMISTOR +#define PA2 56 // E3_THERMISTOR + +// FANS +#define PC4 57 // E1_FAN +#define PC5 58 // E2_FAN +#define PE8 59 // E3_FAN + +// X_MOTOR +#define PE13 60 // X_RESET +#define PE14 61 // X_PWM +#define PE15 62 // X_DIR + +// Y_MOTOR +#define PE10 63 // Y_RESET +#define PB10 64 // Y_PWM +#define PE9 65 // Y_DIR + +// Z_MOTOR +#define PC15 66 // Z_RESET +#define PC6 67 // Z_PWM +#define PC0 68 // Z_DIR + +// E1_MOTOR +#define PC14 69 // E1_RESET +#define PC13 70 // E1_DIR +#define PD12 71 // E1_PWM + +// E2_MOTOR +#define PE4 72 // E2_RESET +#define PE5 73 // E2_PWM +#define PE6 74 // E2_DIR + +// E3_MOTOR +#define PE3 75 // E3_RESET +#define PE2 76 // E3_DIR +#define PB8 77 // E3_PWM + +// This must be a literal +#define NUM_DIGITAL_PINS 78 +// This must be a literal with a value less than or equal to to MAX_ANALOG_INPUTS +#define NUM_ANALOG_INPUTS 6 +#define NUM_ANALOG_FIRST 51 + +// On-board LED pin number +#define LED_BUILTIN PE1 +#define LED_GREEN LED_BUILTIN + +// On-board user button +#define USER_BTN PE7 + +// UART Definitions +#define SERIAL_UART_INSTANCE 1 // Connected to ST-Link +//#define SERIAL_UART_INSTANCE 2 // Connected to WIFI + +// Default pin used for 'Serial' instance (ex: ST-Link) +// Mandatory for Firmata +#if SERIAL_UART_INSTANCE == 1 // ST-Link & J23 + #define PIN_SERIAL_RX PA10 + #define PIN_SERIAL_TX PA9 +#elif SERIAL_UART_INSTANCE == 2 // WIFI interface + #define PIN_SERIAL2_RX PD6 + #define PIN_SERIAL2_TX PD5 +#else + #error "Invalid setting for SERIAL_UART_INSTANCE." +#endif + +// Timer Definitions +#define TIMER_SERVO TIM4 // TIMER_SERVO must be defined in this file +#define TIMER_TONE TIM5 // TIMER_TONE must be defined in this file + +/* SD detect signal */ +/* + * By default, R67 is not provided, so SD card detect is not used. + * Note: SD CD (pin 16 of expansion connector J23) can be connected + * to GND in order to be able to use SD_DETECT_PIN + */ +/*#define SD_DETECT_PIN PA15*/ + +/* HAL configuration */ +#define HSE_VALUE 25000000U + +/* Extra HAL modules */ +#define HAL_SD_MODULE_ENABLED + +#endif + +#ifdef __cplusplus +} // extern "C" +#endif +/*---------------------------------------------------------------------------- + * Arduino objects - C++ only + *----------------------------------------------------------------------------*/ + +#ifdef __cplusplus +// These serial port names are intended to allow libraries and architecture-neutral +// sketches to automatically default to the correct port name for a particular type +// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN, +// the first hardware serial port whose RX/TX pins are not dedicated to another use. +// +// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor +// +// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial +// +// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library +// +// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins. +// +// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX +// pins are NOT connected to anything by default. +#define SERIAL_PORT_MONITOR Serial +#define SERIAL_PORT_HARDWARE Serial1 +#endif + +#endif // _VARIANT_ARDUINO_STM32_ + +// PA0 54 // E1_THERMISTOR +// PA1 55 // E2_THERMISTOR +// PA2 56 // E3_THERMISTOR +// PA3 53 // BED_THERMISTOR_3 +// PA4 16 // SPI_CS +// PA5 17 // SPI_SCK +// PA6 18 // SPI_MISO +// PA7 19 // SPI_MOSI +// PA8 43 // V_STOP +// PA9 0 //TX +// PA10 1 //RX +// PA11 30 //OTG_DM +// PA12 31 //OTG_DP +// PA13 20 // JTAG_TMS/SWDIO +// PA14 21 // JTAG_TCK/SWCLK +// PA15 25 // SD_CARD_DETECT +// PB0 49 // E2_HEAT_PWM +// PB1 50 // E3_HEAT_PWM +// PB3 22 // JTAG_TDO/SWO +// PB4 37 // USER4 +// PB5 6 // WIFI_WAKEUP +// PB6 15 // SCL +// PB7 14 // SDA +// PB8 77 // E3_PWM +// PB9 35 // USER1 +// PB10 64 // Y_PWM +// PB12 10 // SPI_CS +// PB13 13 // SPI_SCK +// PB14 12 // SPI_MISO +// PB15 11 // SPI_MOSI +// PC0 68 // Z_DIR +// PC1 33 //IR_ON +// PC2 51 // BED_THERMISTOR_1 +// PC3 52 // BED_THERMISTOR_2 +// PC4 57 // E1_FAN +// PC5 58 // E2_FAN +// PC6 67 // Z_PWM +// PC7 48 // E1_HEAT_PWM +// PC8 23 // SDIO_D0 +// PC9 24 // SDIO_D1 +// PC10 26 // SDIO_D2 +// PC11 27 // SDIO_D3 +// PC12 28 // SDIO_CK +// PC13 70 // E1_DIR +// PC14 69 // E1_RESET +// PC15 66 // Z_RESET +// PD0 44 // W_STOP +// PD1 32 //IR_OUT +// PD2 29 // SDIO_CMD +// PD3 2 // CTS +// PD4 3 // RTS +// PD5 4 // TX +// PD6 5 // RX +// PD7 34 // USER3 +// PD8 39 // X_STOP +// PD9 40 // Y_STOP +// PD10 41 // Z_STOP +// PD11 42 // U_STOP +// PD12 71 // E1_PWM +// PD13 45 // BED_HEAT_2 +// PD14 46 // BED_HEAT_1 +// PD15 47 // BED_HEAT_3 +// PE0 36 // USER2 +// PE1 9 // STATUS_LED +// PE2 76 // E3_DIR +// PE3 75 // E3_RESET +// PE4 72 // E2_RESET +// PE5 73 // E2_PWM +// PE6 74 // E2_DIR +// PE7 38 // USER_BUTTON +// PE8 59 // E3_FAN +// PE9 65 // Y_DIR +// PE10 63 // Y_RESET +// PE11 7 // WIFI_RESET +// PE12 8 // WIFI_BOOT +// PE13 60 // X_RESET +// PE14 61 // X_PWM +// PE15 62 // X_DIR |