1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
|
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#ifdef ARDUINO_ARCH_SAM
#include "../../inc/MarlinConfig.h"
#include "../../MarlinCore.h"
#include "watchdog.h"
// Override Arduino runtime to either config or disable the watchdog
//
// We need to configure the watchdog as soon as possible in the boot
// process, because watchdog initialization at hardware reset on SAM3X8E
// is unreliable, and there is risk of unintended resets if we delay
// that initialization to a later time.
void watchdogSetup() {
#if ENABLED(USE_WATCHDOG)
// 4 seconds timeout
uint32_t timeout = TERN(WATCHDOG_DURATION_8S, 8000, 4000);
// Calculate timeout value in WDT counter ticks: This assumes
// the slow clock is running at 32.768 kHz watchdog
// frequency is therefore 32768 / 128 = 256 Hz
timeout = (timeout << 8) / 1000;
if (timeout == 0)
timeout = 1;
else if (timeout > 0xFFF)
timeout = 0xFFF;
// We want to enable the watchdog with the specified timeout
uint32_t value =
WDT_MR_WDV(timeout) | // With the specified timeout
WDT_MR_WDD(timeout) | // and no invalid write window
#if !(SAMV70 || SAMV71 || SAME70 || SAMS70)
WDT_MR_WDRPROC | // WDT fault resets processor only - We want
// to keep PIO controller state
#endif
WDT_MR_WDDBGHLT | // WDT stops in debug state.
WDT_MR_WDIDLEHLT; // WDT stops in idle state.
#if ENABLED(WATCHDOG_RESET_MANUAL)
// We enable the watchdog timer, but only for the interrupt.
// Configure WDT to only trigger an interrupt
value |= WDT_MR_WDFIEN; // Enable WDT fault interrupt.
// Disable WDT interrupt (just in case, to avoid triggering it!)
NVIC_DisableIRQ(WDT_IRQn);
// We NEED memory barriers to ensure Interrupts are actually disabled!
// ( https://dzone.com/articles/nvic-disabling-interrupts-on-arm-cortex-m-and-the )
__DSB();
__ISB();
// Initialize WDT with the given parameters
WDT_Enable(WDT, value);
// Configure and enable WDT interrupt.
NVIC_ClearPendingIRQ(WDT_IRQn);
NVIC_SetPriority(WDT_IRQn, 0); // Use highest priority, so we detect all kinds of lockups
NVIC_EnableIRQ(WDT_IRQn);
#else
// a WDT fault triggers a reset
value |= WDT_MR_WDRSTEN;
// Initialize WDT with the given parameters
WDT_Enable(WDT, value);
#endif
// Reset the watchdog
WDT_Restart(WDT);
#else
// Make sure to completely disable the Watchdog
WDT_Disable(WDT);
#endif
}
#if ENABLED(USE_WATCHDOG)
// Initialize watchdog - On SAM3X, Watchdog was already configured
// and enabled or disabled at startup, so no need to reconfigure it
// here.
void watchdog_init() {
// Reset watchdog to start clean
WDT_Restart(WDT);
}
#endif // USE_WATCHDOG
#endif
|
