blob: 40441ac08d1638868a40ae77d7d2ccc5a8c606d2 (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
|
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#include "../../inc/MarlinConfig.h"
#if ENABLED(BACKLASH_GCODE)
#include "../../feature/backlash.h"
#include "../../module/planner.h"
#include "../gcode.h"
/**
* M425: Enable and tune backlash correction.
*
* F<fraction> Enable/disable/fade-out backlash correction (0.0 to 1.0)
* S<smoothing_mm> Distance over which backlash correction is spread
* X<distance_mm> Set the backlash distance on X (0 to disable)
* Y<distance_mm> ... on Y
* Z<distance_mm> ... on Z
* X If a backlash measurement was done on X, copy that value
* Y ... on Y
* Z ... on Z
*
* Type M425 without any arguments to show active values.
*/
void GcodeSuite::M425() {
bool noArgs = true;
auto axis_can_calibrate = [](const uint8_t a) {
switch (a) {
default:
case X_AXIS: return AXIS_CAN_CALIBRATE(X);
case Y_AXIS: return AXIS_CAN_CALIBRATE(Y);
case Z_AXIS: return AXIS_CAN_CALIBRATE(Z);
}
};
LOOP_XYZ(a) {
if (axis_can_calibrate(a) && parser.seen(XYZ_CHAR(a))) {
planner.synchronize();
backlash.distance_mm[a] = parser.has_value() ? parser.value_linear_units() : backlash.get_measurement(AxisEnum(a));
noArgs = false;
}
}
if (parser.seen('F')) {
planner.synchronize();
backlash.set_correction(parser.value_float());
noArgs = false;
}
#ifdef BACKLASH_SMOOTHING_MM
if (parser.seen('S')) {
planner.synchronize();
backlash.smoothing_mm = parser.value_linear_units();
noArgs = false;
}
#endif
if (noArgs) {
SERIAL_ECHOPGM("Backlash Correction ");
if (!backlash.correction) SERIAL_ECHOPGM("in");
SERIAL_ECHOLNPGM("active:");
SERIAL_ECHOLNPAIR(" Correction Amount/Fade-out: F", backlash.get_correction(), " (F1.0 = full, F0.0 = none)");
SERIAL_ECHOPGM(" Backlash Distance (mm): ");
LOOP_XYZ(a) if (axis_can_calibrate(a)) {
SERIAL_CHAR(' ', XYZ_CHAR(a));
SERIAL_ECHO(backlash.distance_mm[a]);
SERIAL_EOL();
}
#ifdef BACKLASH_SMOOTHING_MM
SERIAL_ECHOLNPAIR(" Smoothing (mm): S", backlash.smoothing_mm);
#endif
#if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
SERIAL_ECHOPGM(" Average measured backlash (mm):");
if (backlash.has_any_measurement()) {
LOOP_XYZ(a) if (axis_can_calibrate(a) && backlash.has_measurement(AxisEnum(a))) {
SERIAL_CHAR(' ', XYZ_CHAR(a));
SERIAL_ECHO(backlash.get_measurement(AxisEnum(a)));
}
}
else
SERIAL_ECHOPGM(" (Not yet measured)");
SERIAL_EOL();
#endif
}
}
#endif // BACKLASH_GCODE
|
