blob: 6c7f7f4db63fff81f4ba851e63689f156a440c05 (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
|
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#pragma once
/**
* 3DRAG (and K8200 / K8400) Arduino Mega with RAMPS v1.4 pin assignments
*/
#ifndef BOARD_INFO_NAME
#define BOARD_INFO_NAME "3Drag"
#endif
#ifndef DEFAULT_MACHINE_NAME
#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
#endif
#ifndef DEFAULT_SOURCE_CODE_URL
#define DEFAULT_SOURCE_CODE_URL "3dprint.elettronicain.it"
#endif
//
// Heaters / Fans
//
#define RAMPS_D8_PIN 9
#define RAMPS_D9_PIN 8
#define MOSFET_D_PIN 12
#ifndef CASE_LIGHT_PIN
#define CASE_LIGHT_PIN -1 // Hardware PWM but one is not available on expansion header
#endif
#include "pins_RAMPS.h"
//
// Limit Switches
//
#undef Z_MAX_PIN
//
// Steppers
//
#undef Z_ENABLE_PIN
#define Z_ENABLE_PIN 63
//
// Heaters / Fans
//
#define HEATER_2_PIN 6
//
// Misc. Functions
//
#undef SDSS
#define SDSS 25
#undef SD_DETECT_PIN
#define SD_DETECT_PIN 53
//
// LCD / Controller
//
#if IS_ULTRA_LCD && IS_NEWPANEL
#undef BEEPER_PIN
#undef LCD_PINS_RS
#undef LCD_PINS_ENABLE
#undef LCD_PINS_D4
#undef LCD_PINS_D5
#undef LCD_PINS_D6
#undef LCD_PINS_D7
#define LCD_PINS_RS 27
#define LCD_PINS_ENABLE 29
#define LCD_PINS_D4 37
#define LCD_PINS_D5 35
#define LCD_PINS_D6 33
#define LCD_PINS_D7 31
// Buttons
#undef BTN_EN1
#undef BTN_EN2
#undef BTN_ENC
#define BTN_EN1 16
#define BTN_EN2 17
#define BTN_ENC 23
#else
#define BEEPER_PIN 33
#endif // IS_ULTRA_LCD && IS_NEWPANEL
/**
* M3/M4/M5 - Spindle/Laser Control
*
* If you want to control the speed of your spindle then you'll have
* have to sacrifce the Extruder and pull some signals off the Z stepper
* driver socket.
*
* The following assumes:
* - the Z stepper driver socket is empty
* - the extruder driver socket has a driver board plugged into it
* - the Z stepper wires are attached the the extruder connector
*
* If you want to keep the extruder AND don't have a LCD display then
* you can still control the power on/off and spindle direction.
*
* Where to get spindle signals
*
* stepper signal socket name socket name
* -------
* SPINDLE_LASER_ENA_PIN /ENABLE O| |O VMOT
* MS1 O| |O GND
* MS2 O| |O 2B
* MS3 O| |O 2A
* /RESET O| |O 1A
* /SLEEP O| |O 1B
* SPINDLE_LASER_PWM_PIN STEP O| |O VDD
* SPINDLE_DIR_PIN DIR O| |O GND
* -------
*
* Note: Socket names vary from vendor to vendor
*/
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are not good with 3DRAG
#undef SPINDLE_LASER_ENA_PIN
#undef SPINDLE_DIR_PIN
#if HAS_CUTTER
#if !EXTRUDERS
#undef E0_DIR_PIN
#undef E0_ENABLE_PIN
#undef E0_STEP_PIN
#undef Z_DIR_PIN
#undef Z_ENABLE_PIN
#undef Z_STEP_PIN
#define Z_DIR_PIN 28
#define Z_ENABLE_PIN 24
#define Z_STEP_PIN 26
#define SPINDLE_LASER_PWM_PIN 46 // Hardware PWM
#define SPINDLE_LASER_ENA_PIN 62 // Pullup!
#define SPINDLE_DIR_PIN 48
#elif !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // Use expansion header if no LCD in use
#define SPINDLE_LASER_ENA_PIN 16 // Pullup or pulldown!
#define SPINDLE_DIR_PIN 17
#endif
#endif
|
