1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
|
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#pragma once
/**
* Arduino Mega with RAMPS v1.4 adjusted pin assignments
*
* MKS GEN v1.3 (Extruder, Fan, Bed)
* MKS GEN v1.3 (Extruder, Extruder, Fan, Bed)
* MKS GEN v1.4 (Extruder, Fan, Bed)
* MKS GEN v1.4 (Extruder, Extruder, Fan, Bed)
*/
#if HOTENDS > 2 || E_STEPPERS > 2
#error "MKS GEN 1.3/1.4 supports up to 2 hotends / E-steppers. Comment out this line to continue."
#endif
#define BOARD_INFO_NAME "MKS GEN >= v1.3"
//
// Heaters / Fans
//
// Power outputs EFBF or EFBE
#define MOSFET_D_PIN 7
//
// PSU / SERVO
//
// If PSU_CONTROL is specified, always hijack Servo 3
//
#if ENABLED(PSU_CONTROL)
#define SERVO3_PIN -1
#define PS_ON_PIN 4
#endif
#include "pins_RAMPS.h"
//
// LCD / Controller
//
#if ANY(VIKI2, miniVIKI)
/**
* VIKI2 Has two groups of wires with...
*
* +Vin + Input supply, requires 120ma for LCD and mSD card
* GND Ground Pin
* MOSI Data input for LCD and SD
* MISO Data output for SD
* SCK Clock for LCD and SD
* AO Reg. Sel for LCD
* LCS Chip Select for LCD
* SDCS Chip Select for SD
* SDCD Card Detect pin for SD
* ENCA Encoder output A
* ENCB Encoder output B
* ENCBTN Encoder button switch
*
* BTN Panel mounted button switch
* BUZZER Piezo buzzer
* BLUE-LED Blue LED ring pin (3 to 5v, mosfet buffered)
* RED-LED Red LED ring pin (3 to 5v, mosfet buffered)
*
* This configuration uses the following arrangement:
*
* EXP1 D37 = EN2 D35 = EN1 EXP2 D50 = MISO D52 = SCK
* D17 = BLUE D16 = RED D31 = ENC D53 = SDCS
* D23 = KILL D25 = BUZZ D33 = --- D51 = MOSI
* D27 = A0 D29 = LCS D49 = SDCD RST = ---
* GND = GND 5V = 5V GND = --- D41 = ---
*/
#undef BTN_EN1
#undef BTN_EN2
#undef BTN_ENC
#undef DOGLCD_A0
#undef DOGLCD_CS
#undef SD_DETECT_PIN
#undef BEEPER_PIN
#undef KILL_PIN
#undef STAT_LED_RED_PIN
#undef STAT_LED_BLUE_PIN
//
// VIKI2 12-wire lead
//
// orange/white SDCD
#define SD_DETECT_PIN 49
// white ENCA
#define BTN_EN1 35
// green ENCB
#define BTN_EN2 37
// purple ENCBTN
#define BTN_ENC 31
// brown A0
#define DOGLCD_A0 27
// green/white LCS
#define DOGLCD_CS 29
// 50 gray MISO
// 51 yellow MOSI
// 52 orange SCK
// blue SDCS
//#define SDSS 53
//
// VIKI2 4-wire lead
//
// blue BTN
#define KILL_PIN 23
// green BUZZER
#define BEEPER_PIN 25
// yellow RED-LED
#define STAT_LED_RED_PIN 16
// white BLUE-LED
#define STAT_LED_BLUE_PIN 17
#endif
|
