blob: d064d801329d1ad98b16686777bb50096524e8c7 (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
|
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#pragma once
#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega1284P__)
#error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644P' or 'ATmega1284P' in 'Tools > Processor.'"
#endif
#define BOARD_INFO_NAME "Zonestar ZMIB_V2"
#define BOARD_WEBSITE_URL "www.aliexpress.com/item/32957490744.html"
#define IS_ZMIB_V2
/**
* ZMIB pin assignments
*
* The ZMIB board needs a bootloader installed before Marlin can be uploaded.
* If you don't have a chip programmer you can use a spare Arduino plus a few
* electronic components to write the bootloader.
*
* See http://www.instructables.com/id/Burn-Arduino-Bootloader-with-Arduino-MEGA/
*/
/**
* PIN: 0 Port: B0 HEATER_0_PIN
* PIN: 1 Port: B1 HEATER_BED_PIN
* PIN: 2 Port: B2 EXP1_4(BTN_EN2)
* PIN: 3 Port: B3 V1: SD_DETECT_PIN
* PIN: 3 Port: B3 V2: EXP1_6
* PIN: 4 Port: B4 SDSS
* PIN: 4 Port: B4 V1: EXP1_6
* PIN: 5 Port: B5 AVR_MOSI_PIN
* . SD_MOSI_PIN
* PIN: 6 Port: B6 AVR_MISO_PIN
* . EXP1_9(SD_MISO_PIN)
* PIN: 7 Port: B7 AVR_SCK_PIN
* . EXP1_10(SD_SCK_PIN)
* PIN: 8 Port: D0 RXD
* PIN: 9 Port: D1 TXD
* PIN: 10 Port: D2 EXP1_8
* PIN: 11 Port: D3 EXP1_7
* PIN: 12 Port: D4 EXP1_5(BTN_EN1)
* PIN: 13 Port: D5 Z_MIN_PIN
* PIN: 14 Port: D6 E1_DIR_PIN
* PIN: 15 Port: D7 E1_STEP_PIN
* PIN: 16 Port: C0 Z_DIR_PIN
* PIN: 17 Port: C1 Z_STEP_PIN
* PIN: 18 Port: C2 Y_MIN_PIN
* PIN: 19 Port: C3 Y_DIR_PIN
* PIN: 20 Port: C4 Y_STEP_PIN
* PIN: 21 Port: C5 X_MIN_PIN
* PIN: 22 Port: C6 X_DIR_PIN
* PIN: 23 Port: C7 X_STEP_PIN
* PIN: 24 Port: A7 X_ENABLE_PIN
* Y_ENABLE_PIN
* Z_ENABLE_PIN
* E0_ENABLE_PIN
* E1_ENABLE_PIN
* PIN: 25 Port: A6 FIL_RUNOUT_PIN
* PIN: 26 Port: A5 E0_DIR_PIN
* PIN: 27 Port: A4 E0_STEP_PIN
* PIN: 28 Port: A3 FAN_PIN
* PIN: 29 Port: A2 EXP1_3(BTN_ENC)
* ADC_KEY_PIN
* PIN: 30 Port: A1 TEMP_0_PIN
* PIN: 31 Port: A0 TEMP_BED_PIN
*/
//
// Limit Switches
//
#define X_MIN_PIN 21
#define Y_MIN_PIN 18
#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT)
#define Z_MIN_PIN 25
#else
#define Z_MIN_PIN 13
#endif
//
// Steppers
//
#define X_STEP_PIN 23
#define X_DIR_PIN 22
#define X_ENABLE_PIN 24
#define Y_STEP_PIN 20
#define Y_DIR_PIN 19
#define Y_ENABLE_PIN 24
#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT)
#define Z_STEP_PIN 27
#define Z_DIR_PIN 26
#else
#define Z_STEP_PIN 17
#define Z_DIR_PIN 16
#endif
#define Z_ENABLE_PIN 24
#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT)
#define E0_STEP_PIN 15
#define E0_DIR_PIN 14
#else
#define E0_STEP_PIN 27
#define E0_DIR_PIN 26
#endif
#define E0_ENABLE_PIN 24
#define E1_STEP_PIN 15
#define E1_DIR_PIN 14
#define E1_ENABLE_PIN 24
//
// Temperature Sensors
//
#define TEMP_0_PIN 1 // Analog Input
#define TEMP_BED_PIN 0 // Analog Input
//
// Heaters / Fans
//
#define HEATER_0_PIN 0
#define HEATER_BED_PIN 1
#define FAN_PIN 28
#define FAN1_PIN -1
//
//filament run out sensor
//
#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT)
#define FIL_RUNOUT_PIN 13
#else
#define FIL_RUNOUT_PIN 25 // Z-MIN
#endif
//
// SD card
//
#if ENABLED(SDSUPPORT)
#define SDSS 4
#endif
#define SD_DETECT_PIN -1
/*===================================================
* ZMIB Version 1 - EXP1 Connector
* MOSI(D5) TX1(D11) ENA(D12) ENC(D29/A2) 5V
* SCK(D7) RX1(D10) SCS(D4) ENB(D2) GND
*===================================================
* ZMIB Version 2 - EXP1 Connector
* MOSI(D5) TX1(D11) ENA(D12) ENC(D29/A2) 5V
* SCK(D7) RX1(D10) SCS(D3) ENB(D2) GND
*===================================================
* LCD 128x64
*==================================================*/
#if ENABLED(ZONESTAR_12864LCD)
//
// LCD 128x64
//
#define LCDSCREEN_NAME "ZONESTAR_12864LCD"
#define FORCE_SOFT_SPI
//#define LCD_SDSS 11
#define LCD_PINS_RS 11 // ST7920_CS_PIN LCD_PIN_RS (PIN4 of LCD module)
#ifdef IS_ZMIB_V2
#define LCD_PINS_ENABLE 3 // ST7920_DAT_PIN LCD_PIN_R/W (PIN5 of LCD module)
#else
#define LCD_PINS_ENABLE 4 // ST7920_DAT_PIN LCD_PIN_R/W (PIN5 of LCD module)
#endif
#define LCD_PINS_D4 10 // ST7920_CLK_PIN LCD_PIN_ENABLE (PIN6 of LCD module)
// Alter timing for graphical display
#define ST7920_DELAY_1 DELAY_2_NOP
#define ST7920_DELAY_2 DELAY_2_NOP
#define ST7920_DELAY_3 DELAY_2_NOP
#elif EITHER(ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306)
//
// OLED 128x64
//
#define LCDSCREEN_NAME "ZONESTAR 12864OLED"
#define FORCE_SOFT_SPI
#ifdef IS_ZMIB_V2
#define LCD_PINS_RS 3 // RESET
#else
#define LCD_PINS_RS 4 // RESET
#endif
#define LCD_PINS_DC 10 // DC
#define DOGLCD_CS 11 // CS
#if ENABLED(OLED_HW_IIC)
#error "Oops! can't choose HW IIC for ZMIB board!!"
#elif ENABLED(OLED_HW_SPI)
// HW SPI
#define DOGLCD_A0 LCD_PINS_DC // A0 = DC
#else
// SW SPI
#define DOGLCD_A0 LCD_PINS_DC // A0 = DC
#define DOGLCD_MOSI AVR_MOSI_PIN // SDA
#define DOGLCD_SCK AVR_SCK_PIN // SCK
#endif
#endif
//
// All the above are also RRDSC with rotary encoder
//
#if IS_RRD_SC
#define BTN_EN1 2
#define BTN_EN2 12
#define BTN_ENC 29
#define BEEPER_PIN -1
#define KILL_PIN -1
#endif
|
