blob: 2278d558702ecb2102547077457f9020feb2cd34 (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
|
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#pragma once
#if NOT_TARGET(__STM32F1__)
#error "Oops! Select an STM32F1 board in 'Tools > Board.'"
#endif
#define BOARD_INFO_NAME "FLY_MINI"
#define BOARD_WEBSITE_URL "github.com/FLYmaker"
#define DISABLE_JTAG
//
// Flash EEPROM Emulation
//
#define FLASH_EEPROM_EMULATION
#define EEPROM_PAGE_SIZE 0x800 // 2KB
#define EEPROM_START_ADDRESS (0x8000000 + 256 * 1024 - 2 * EEPROM_PAGE_SIZE) // 256K firmware space
#define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE
//
// Servos
//
#define SERVO0_PIN PA8
//
// Limit Switches
//
#define X_MIN_PIN PC12
#define X_MAX_PIN PC11
#define Y_MIN_PIN PC10
#define Y_MAX_PIN PA15
#define Z_MIN_PIN PA14
#define Z_MAX_PIN PA13
//
// Steppers
//
#define X_STEP_PIN PB1
#define X_DIR_PIN PB2
#define X_ENABLE_PIN PB10
#ifndef X_CS_PIN
#define X_CS_PIN PB0
#endif
#define Y_STEP_PIN PA2
#define Y_DIR_PIN PC4
#define Y_ENABLE_PIN PC5
#ifndef Y_CS_PIN
#define Y_CS_PIN PA7
#endif
#define Z_STEP_PIN PA3
#define Z_DIR_PIN PA5
#define Z_ENABLE_PIN PA6
#ifndef Z_CS_PIN
#define Z_CS_PIN PA4
#endif
#define E0_STEP_PIN PA1
#define E0_DIR_PIN PC3
#define E0_ENABLE_PIN PA0
#ifndef E0_CS_PIN
#define E0_CS_PIN PC2
#endif
#if ENABLED(TMC_USE_SW_SPI)
#ifndef TMC_SW_MOSI
#define TMC_SW_MOSI PB15
#endif
#ifndef TMC_SW_MISO
#define TMC_SW_MISO PB14
#endif
#ifndef TMC_SW_SCK
#define TMC_SW_SCK PB13
#endif
#endif
#if HAS_TMC_UART
//
// Software serial
//
#define X_SERIAL_TX_PIN PB0
#define X_SERIAL_RX_PIN PB0
#define Y_SERIAL_TX_PIN PA7
#define Y_SERIAL_RX_PIN PA7
#define Z_SERIAL_TX_PIN PA4
#define Z_SERIAL_RX_PIN PA4
#define E0_SERIAL_TX_PIN PC2
#define E0_SERIAL_RX_PIN PC2
#endif
//
// Heaters / Fans
//
#define HEATER_0_PIN PC6
#define HEATER_BED_PIN PC7
#ifndef FAN_PIN
#define FAN_PIN PC8
#endif
#define FAN1_PIN PC9
//
// Temperature Sensors
//
#define TEMP_BED_PIN PC0 // Analog Input
#define TEMP_0_PIN PC1 // Analog Input
//
// LCD Pins
//
//
// LCD / Controller
//
#define SPI_DEVICE 2
#define SD_SS_PIN PB12
#define SD_SCK_PIN PB13
#define SD_MISO_PIN PB14
#define SD_MOSI_PIN PB15
#define SDSS SD_SS_PIN
#define SD_DETECT_PIN PB11
#define BEEPER_PIN PC14
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PB9
#define LCD_PINS_D4 PB7
#define LCD_PINS_D5 PB6
#define LCD_PINS_D6 PB5
#define LCD_PINS_D7 PB4
#define BTN_EN1 PD2
#define BTN_EN2 PB3
#define BTN_ENC PC13
#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
#define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder
#endif
//
// Filament runout
//
//
// ST7920 Delays
//
#ifndef ST7920_DELAY_1
#define ST7920_DELAY_1 DELAY_NS(96)
#endif
#ifndef ST7920_DELAY_2
#define ST7920_DELAY_2 DELAY_NS(48)
#endif
#ifndef ST7920_DELAY_3
#define ST7920_DELAY_3 DELAY_NS(715)
#endif
|
