Initial commit

1 files changed, 518 insertions, 0 deletions

diff --git a/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h b/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h
new file mode 100644
index 0000000..6584030
--- /dev/null
+++ b/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h
@@ -0,0 +1,518 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+/**
+ * Re-ARM with RAMPS v1.4 pin assignments
+ *
+ * Applies to the following boards:
+ *
+ *  RAMPS_14_EFB (Hotend, Fan, Bed)
+ *  RAMPS_14_EEB (Hotend0, Hotend1, Bed)
+ *  RAMPS_14_EFF (Hotend, Fan0, Fan1)
+ *  RAMPS_14_EEF (Hotend0, Hotend1, Fan)
+ *  RAMPS_14_SF  (Spindle, Controller Fan)
+ */
+
+// Numbers in parentheses () are the corresponding mega2560 pin numbers
+
+#if NOT_TARGET(MCU_LPC1768)
+  #error "Oops! Make sure you have the LPC1768 environment selected in your IDE."
+#endif
+
+#define BOARD_INFO_NAME "Re-ARM RAMPS 1.4"
+
+//
+// Servos
+//
+#define SERVO0_PIN                         P1_20  // (11)
+#define SERVO1_PIN                         P1_21  // ( 6) also on J5-1
+#define SERVO2_PIN                         P1_19  // ( 5)
+#define SERVO3_PIN                         P1_18  // ( 4) 5V output
+
+//
+// Limit Switches
+//
+#define X_MIN_PIN                          P1_24  // ( 3) 10k pullup to 3.3V, 1K series
+#define X_MAX_PIN                          P1_25  // ( 2) 10k pullup to 3.3V, 1K series
+#define Y_MIN_PIN                          P1_26  // (14) 10k pullup to 3.3V, 1K series
+#define Y_MAX_PIN                          P1_27  // (15) 10k pullup to 3.3V, 1K series
+#define Z_MIN_PIN                          P1_29  // (18) 10k pullup to 3.3V, 1K series
+#define Z_MAX_PIN                          P1_28  // (19) 10k pullup to 3.3V, 1K series
+#define ONBOARD_ENDSTOPPULLUPS                    // Board has built-in pullups
+
+//
+// Steppers
+//
+#define X_STEP_PIN                         P2_01  // (54)
+#define X_DIR_PIN                          P0_11  // (55)
+#define X_ENABLE_PIN                       P0_10  // (38)
+#ifndef X_CS_PIN
+  #define X_CS_PIN                         P1_01  // ETH
+#endif
+
+#define Y_STEP_PIN                         P2_02  // (60)
+#define Y_DIR_PIN                          P0_20  // (61)
+#define Y_ENABLE_PIN                       P0_19  // (56)
+#ifndef Y_CS_PIN
+  #define Y_CS_PIN                         P1_04  // ETH
+#endif
+
+#define Z_STEP_PIN                         P2_03  // (46)
+#define Z_DIR_PIN                          P0_22  // (48)
+#define Z_ENABLE_PIN                       P0_21  // (62)
+#ifndef Z_CS_PIN
+  #define Z_CS_PIN                         P1_10  // ETH
+#endif
+
+#define E0_STEP_PIN                        P2_00  // (26)
+#define E0_DIR_PIN                         P0_05  // (28)
+#define E0_ENABLE_PIN                      P0_04  // (24)
+#ifndef E0_CS_PIN
+  #define E0_CS_PIN                        P1_14  // ETH
+#endif
+
+#define E1_STEP_PIN                        P2_08  // (36)
+#define E1_DIR_PIN                         P2_13  // (34)
+#define E1_ENABLE_PIN                      P4_29  // (30)
+#ifndef E1_CS_PIN
+  #define E1_CS_PIN                        -1
+#endif
+
+//
+// Software SPI pins for TMC2130 stepper drivers
+//
+#if ENABLED(TMC_USE_SW_SPI)
+  #ifndef TMC_SW_MOSI
+    #define TMC_SW_MOSI                    P1_00  // ETH
+  #endif
+  #ifndef TMC_SW_MISO
+    #define TMC_SW_MISO                    P1_08  // ETH
+  #endif
+  #ifndef TMC_SW_SCK
+    #define TMC_SW_SCK                     P1_09  // ETH
+  #endif
+#endif
+
+#if HAS_TMC_UART
+  /**
+   * TMC2208/TMC2209 stepper drivers
+   *
+   * Hardware serial communication ports.
+   * If undefined software serial is used according to the pins below
+   */
+
+  //
+  // Software serial
+  //
+
+  // P2_08 E1-Step
+  // P2_13 E1-Dir
+
+  #ifndef X_SERIAL_TX_PIN
+    #define X_SERIAL_TX_PIN                P0_01
+  #endif
+  #ifndef X_SERIAL_RX_PIN
+    #define X_SERIAL_RX_PIN                P0_01
+  #endif
+
+  #ifndef Y_SERIAL_TX_PIN
+    #define Y_SERIAL_TX_PIN                P0_00
+  #endif
+  #ifndef Y_SERIAL_RX_PIN
+    #define Y_SERIAL_RX_PIN                P0_00
+  #endif
+
+  #ifndef Z_SERIAL_TX_PIN
+    #define Z_SERIAL_TX_PIN                P2_13
+  #endif
+  #ifndef Z_SERIAL_RX_PIN
+    #define Z_SERIAL_RX_PIN                P2_13
+  #endif
+
+  #ifndef E0_SERIAL_TX_PIN
+    #define E0_SERIAL_TX_PIN               P2_08
+  #endif
+  #ifndef E0_SERIAL_RX_PIN
+    #define E0_SERIAL_RX_PIN               P2_08
+  #endif
+
+  // Reduce baud rate to improve software serial reliability
+  #define TMC_BAUD_RATE                    19200
+#endif
+
+//
+// Temperature Sensors
+//  3.3V max when defined as an analog input
+//
+#define TEMP_0_PIN                      P0_23_A0  // A0 (T0) - (67) - TEMP_0_PIN
+#define TEMP_BED_PIN                    P0_24_A1  // A1 (T1) - (68) - TEMP_BED_PIN
+#define TEMP_1_PIN                      P0_25_A2  // A2 (T2) - (69) - TEMP_1_PIN
+#define TEMP_2_PIN                      P0_26_A3  // A3 - (63) - J5-3 & AUX-2
+#define TEMP_3_PIN                      P1_30_A4  // A4 - (37) - BUZZER_PIN
+//#define TEMP_4_PIN                    P1_31_A5  // A5 - (49) - SD_DETECT_PIN
+//#define ??                  P0_03_A6            // A6 - ( 0)  - RXD0 - J4-4 & AUX-1
+#define FILWIDTH_PIN                    P0_02_A7  // A7 - ( 1)  - TXD0 - J4-5 & AUX-1
+
+//
+// Augmentation for auto-assigning RAMPS plugs
+//
+#if NONE(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D)
+  #if HAS_MULTI_HOTEND
+    #if TEMP_SENSOR_BED
+      #define IS_RAMPS_EEB
+    #else
+      #define IS_RAMPS_EEF
+    #endif
+  #elif TEMP_SENSOR_BED
+    #define IS_RAMPS_EFB
+  #else
+    #define IS_RAMPS_EFF
+  #endif
+#endif
+
+//
+// Heaters / Fans
+//
+#ifndef MOSFET_D_PIN
+  #define MOSFET_D_PIN                     -1
+#endif
+#ifndef RAMPS_D8_PIN
+  #define RAMPS_D8_PIN                     P2_07  // (8)
+#endif
+#ifndef RAMPS_D9_PIN
+  #define RAMPS_D9_PIN                     P2_04  // (9)
+#endif
+#ifndef RAMPS_D10_PIN
+  #define RAMPS_D10_PIN                    P2_05  // (10)
+#endif
+
+#define HEATER_0_PIN               RAMPS_D10_PIN
+
+#if ENABLED(IS_RAMPS_EFB)                         // Hotend, Fan, Bed
+  #define HEATER_BED_PIN            RAMPS_D8_PIN
+#elif ENABLED(IS_RAMPS_EEF)                       // Hotend, Hotend, Fan
+  #define HEATER_1_PIN              RAMPS_D9_PIN
+#elif ENABLED(IS_RAMPS_EEB)                       // Hotend, Hotend, Bed
+  #define HEATER_1_PIN              RAMPS_D9_PIN
+  #define HEATER_BED_PIN            RAMPS_D8_PIN
+#elif ENABLED(IS_RAMPS_EFF)                       // Hotend, Fan, Fan
+  #define FAN1_PIN                  RAMPS_D8_PIN
+#elif DISABLED(IS_RAMPS_SF)                       // Not Spindle, Fan (i.e., "EFBF" or "EFBE")
+  #define HEATER_BED_PIN            RAMPS_D8_PIN
+  #if HOTENDS == 1
+    #define FAN1_PIN                MOSFET_D_PIN
+  #else
+    #define HEATER_1_PIN            MOSFET_D_PIN
+  #endif
+#endif
+
+#ifndef FAN_PIN
+  #if EITHER(IS_RAMPS_EFB, IS_RAMPS_EFF)          // Hotend, Fan, Bed or Hotend, Fan, Fan
+    #define FAN_PIN                 RAMPS_D9_PIN
+  #elif EITHER(IS_RAMPS_EEF, IS_RAMPS_SF)         // Hotend, Hotend, Fan or Spindle, Fan
+    #define FAN_PIN                 RAMPS_D8_PIN
+  #elif ENABLED(IS_RAMPS_EEB)                     // Hotend, Hotend, Bed
+    #define FAN_PIN                        P1_18  // (4) IO pin. Buffer needed
+  #else                                           // Non-specific are "EFB" (i.e., "EFBF" or "EFBE")
+    #define FAN_PIN                 RAMPS_D9_PIN
+  #endif
+#endif
+
+//
+// Misc. Functions
+//
+#define LED_PIN                            P4_28  // (13)
+
+// define digital pin 5 for the filament runout sensor. Use the RAMPS 1.4 digital input 5 on the servos connector
+#ifndef FIL_RUNOUT_PIN
+  #define FIL_RUNOUT_PIN                   P1_19  // (5)
+#endif
+
+#define PS_ON_PIN                          P2_12  // (12)
+
+#if !defined(MAX6675_SS_PIN) && DISABLED(USE_ZMAX_PLUG)
+  #define MAX6675_SS_PIN                   P1_28
+#endif
+
+#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENA_PIN)
+  #if !defined(NUM_SERVOS) || NUM_SERVOS < 4      // Try to use servo connector
+    #define CASE_LIGHT_PIN                 P1_18  // (4) MUST BE HARDWARE PWM
+  #endif
+#endif
+
+//
+// M3/M4/M5 - Spindle/Laser Control
+//            Use servo pins, if available
+//
+#if HAS_CUTTER && !PIN_EXISTS(SPINDLE_LASER_ENA)
+  #if NUM_SERVOS > 1
+    #if ENABLED(SPINDLE_FEATURE)
+      #error "SPINDLE_FEATURE requires 3 free servo pins."
+    #else
+      #error "LASER_FEATURE requires 3 free servo pins."
+    #endif
+  #endif
+  #define SPINDLE_LASER_ENA_PIN       SERVO1_PIN  // (6) Pin should have a pullup/pulldown!
+  #define SPINDLE_LASER_PWM_PIN       SERVO3_PIN  // (4) MUST BE HARDWARE PWM
+  #define SPINDLE_DIR_PIN             SERVO2_PIN  // (5)
+#endif
+
+//
+// Průša i3 MK2 Multiplexer Support
+//
+#if SERIAL_PORT != 0 && SERIAL_PORT_2 != 0
+  #define E_MUX0_PIN                       P0_03  // ( 0) Z_CS_PIN
+  #define E_MUX1_PIN                       P0_02  // ( 1) E0_CS_PIN
+#endif
+#define E_MUX2_PIN                         P0_26  // (63) E1_CS_PIN
+
+/**
+ * LCD / Controller
+ *
+ * All controllers can use J3 and J5 on the Re-ARM board. Custom cabling will be required.
+ *
+ * - https://github.com/wolfmanjm/universal-panel-adapter
+ * - https://panucattdevices.freshdesk.com/support/solutions/articles/1000243195-lcd-display-installation
+ */
+
+/**
+ * Smart LCD adapter
+ *
+ * The Smart LCD adapter can be used for the two 10 pin LCD controllers such as
+ * REPRAP_DISCOUNT_SMART_CONTROLLER. It can't be used for controllers that use
+ * DOGLCD_A0, DOGLCD_CS, LCD_PINS_D5, LCD_PINS_D6 or LCD_PINS_D7. A custom cable
+ * is needed to pick up 5V for the EXP1 connection.
+ *
+ * SD card on the LCD uses the same SPI signals as the LCD. This results in garbage/lines
+ * on the LCD display during accesses of the SD card. The menus/code has been arranged so
+ * that the garbage/lines are erased immediately after the SD card accesses are completed.
+ */
+
+#if ENABLED(CR10_STOCKDISPLAY)
+
+  // Re-Arm can support Creality stock display without SD card reader and single cable on EXP3.
+  // Re-Arm J3 pins 1 (p1.31) & 2 (P3.26) are not used. Stock cable will need to have one
+  // 10-pin IDC connector trimmed or replaced with a 12-pin IDC connector to fit J3.
+  // Requires REVERSE_ENCODER_DIRECTION in Configuration.h
+
+  #define BEEPER_PIN                       P2_11  // J3-3 & AUX-4
+
+  #define BTN_EN1                          P0_16  // J3-7 & AUX-4
+  #define BTN_EN2                          P1_23  // J3-5 & AUX-4
+  #define BTN_ENC                          P3_25  // J3-4 & AUX-4
+
+  #define LCD_PINS_RS                      P0_15  // J3-9 & AUX-4 (CS)
+  #define LCD_PINS_ENABLE                  P0_18  // J3-10 & AUX-3 (SID, MOSI)
+  #define LCD_PINS_D4                      P2_06  // J3-8 & AUX-3 (SCK, CLK)
+
+#elif ENABLED(ZONESTAR_LCD)
+
+  #error "CAUTION! ZONESTAR_LCD on REARM requires wiring modifications. NB. ADCs are not 5V tolerant. Comment out this line to continue."
+
+#elif IS_TFTGLCD_PANEL
+
+  #if ENABLED(TFTGLCD_PANEL_SPI)
+    #define TFTGLCD_CS                     P3_26  // (31) J3-2 & AUX-4
+  #endif
+
+  #define SD_DETECT_PIN                    P1_31  // (49) J3-1 & AUX-3 (NOT 5V tolerant)
+  #define KILL_PIN                         P1_22  // (41) J5-4 & AUX-4
+
+#elif HAS_WIRED_LCD
+
+  #if ENABLED(FYSETC_MINI_12864)
+    #define BEEPER_PIN                     P1_01
+    #define BTN_ENC                        P1_04
+  #else
+    #define BEEPER_PIN                     P1_30  // (37) not 5V tolerant
+    #define BTN_ENC                        P2_11  // (35) J3-3 & AUX-4
+  #endif
+
+  #define BTN_EN1                          P3_26  // (31) J3-2 & AUX-4
+  #define BTN_EN2                          P3_25  // (33) J3-4 & AUX-4
+
+  #define SD_DETECT_PIN                    P1_31  // (49) J3-1 & AUX-3 (NOT 5V tolerant)
+  #define KILL_PIN                         P1_22  // (41) J5-4 & AUX-4
+  #define LCD_PINS_RS                      P0_16  // (16) J3-7 & AUX-4
+  #define LCD_SDSS                         P1_23  // (53) J3-5 & AUX-3
+
+  #if IS_NEWPANEL
+    #if IS_RRW_KEYPAD
+      #define SHIFT_OUT_PIN                P0_18  // (51) (MOSI) J3-10 & AUX-3
+      #define SHIFT_CLK_PIN                P0_15  // (52) (SCK)  J3-9 & AUX-3
+      #define SHIFT_LD_PIN                 P1_31  // (49)        J3-1 & AUX-3 (NOT 5V tolerant)
+    #endif
+  #else
+    //#define SHIFT_CLK_PIN                P3_26  // (31)  J3-2 & AUX-4
+    //#define SHIFT_LD_PIN                 P3_25  // (33)  J3-4 & AUX-4
+    //#define SHIFT_OUT_PIN                P2_11  // (35)  J3-3 & AUX-4
+    //#define SHIFT_EN_PIN                 P1_22  // (41)  J5-4 & AUX-4
+  #endif
+
+  #if ANY(VIKI2, miniVIKI)
+    //#define LCD_SCREEN_ROT_180
+
+    #define DOGLCD_CS                      P0_16  // (16)
+    #define DOGLCD_A0                      P2_06  // (59) J3-8 & AUX-2
+    #define DOGLCD_SCK                SD_SCK_PIN
+    #define DOGLCD_MOSI              SD_MOSI_PIN
+
+    #define STAT_LED_BLUE_PIN              P0_26  // (63)  may change if cable changes
+    #define STAT_LED_RED_PIN               P1_21  // ( 6)  may change if cable changes
+
+  #else
+
+    #if ENABLED(FYSETC_MINI_12864)
+      #define DOGLCD_SCK                   P0_15
+      #define DOGLCD_MOSI                  P0_18
+
+      // EXP1 on LCD adapter is not usable - using Ethernet connector instead
+      #define DOGLCD_CS                    P1_09
+      #define DOGLCD_A0                    P1_14
+      //#define FORCE_SOFT_SPI                    // Use this if default of hardware SPI causes display problems
+                                                  //   results in LCD soft SPI mode 3, SD soft SPI mode 0
+
+      #define LCD_RESET_PIN                P0_16  // Must be high or open for LCD to operate normally.
+
+      #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
+        #ifndef RGB_LED_R_PIN
+          #define RGB_LED_R_PIN            P1_00
+        #endif
+        #ifndef RGB_LED_G_PIN
+          #define RGB_LED_G_PIN            P1_01
+        #endif
+        #ifndef RGB_LED_B_PIN
+          #define RGB_LED_B_PIN            P1_08
+        #endif
+      #elif ENABLED(FYSETC_MINI_12864_2_1)
+        #define NEOPIXEL_PIN               P1_00
+      #endif
+    #else
+      #define DOGLCD_CS                    P0_26  // (63) J5-3 & AUX-2
+      #define DOGLCD_A0                    P2_06  // (59) J3-8 & AUX-2
+    #endif
+
+    #define LCD_BACKLIGHT_PIN              P0_16  //(16) J3-7 & AUX-4 - only used on DOGLCD controllers
+    #define LCD_PINS_ENABLE                P0_18  // (51) (MOSI) J3-10 & AUX-3
+    #define LCD_PINS_D4                    P0_15  // (52) (SCK)  J3-9 & AUX-3
+    #if IS_ULTIPANEL
+      #define LCD_PINS_D5                  P1_17  // (71) ENET_MDIO
+      #define LCD_PINS_D6                  P1_14  // (73) ENET_RX_ER
+      #define LCD_PINS_D7                  P1_10  // (75) ENET_RXD1
+
+      #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
+        #define BTN_ENC_EN           LCD_PINS_D7  // Detect the presence of the encoder
+      #endif
+
+    #endif
+  #endif
+
+  #if ENABLED(MINIPANEL)
+    // GLCD features
+    // Uncomment screen orientation
+    //#define LCD_SCREEN_ROT_90
+    //#define LCD_SCREEN_ROT_180
+    //#define LCD_SCREEN_ROT_270
+ #endif
+
+#endif // HAS_WIRED_LCD
+
+//
+// Ethernet pins
+//
+#if !IS_ULTIPANEL
+  #define ENET_MDIO                        P1_17  // (71)  J12-4
+  #define ENET_RX_ER                       P1_14  // (73)  J12-6
+  #define ENET_RXD1                        P1_10  // (75)  J12-8
+#endif
+#define ENET_MOC                           P1_16  // (70)  J12-3
+#define REF_CLK                            P1_15  // (72)  J12-5
+#define ENET_RXD0                          P1_09  // (74)  J12-7
+#define ENET_CRS                           P1_08  // (76)  J12-9
+#define ENET_TX_EN                         P1_04  // (77)  J12-10
+#define ENET_TXD0                          P1_00  // (78)  J12-11
+#define ENET_TXD1                          P1_01  // (79)  J12-12
+
+//
+// SD Support
+//
+#ifndef SDCARD_CONNECTION
+  #define SDCARD_CONNECTION              ONBOARD
+#endif
+
+#define ONBOARD_SD_CS_PIN                  P0_06  // Chip select for "System" SD card
+
+#if SD_CONNECTION_IS(LCD)
+  #define SD_SCK_PIN                       P0_15  // (52)  system defined J3-9 & AUX-3
+  #define SD_MISO_PIN                      P0_17  // (50)  system defined J3-10 & AUX-3
+  #define SD_MOSI_PIN                      P0_18  // (51)  system defined J3-10 & AUX-3
+  #define SD_SS_PIN                        P1_23  // (53)  system defined J3-5 & AUX-3 (Sometimes called SDSS) - CS used by Marlin
+#elif SD_CONNECTION_IS(ONBOARD)
+  #undef SD_DETECT_PIN
+  #define SD_SCK_PIN                       P0_07
+  #define SD_MISO_PIN                      P0_08
+  #define SD_MOSI_PIN                      P0_09
+  #define SD_SS_PIN            ONBOARD_SD_CS_PIN
+#elif SD_CONNECTION_IS(CUSTOM_CABLE)
+  #error "No custom SD drive cable defined for this board."
+#endif
+
+/**
+ *  Fast PWMs
+ *
+ *  The LPC1768's hardware PWM controller has 6 channels. Each channel
+ *  can be setup to either control a dedicated pin directly or to generate
+ *  an interrupt. The direct method's duty cycle is accurate to within a
+ *  a microsecond. The interrupt method's average duty cycle has the
+ *  the same accuracy but the individual cycles can vary because of higher
+ *  priority interrupts.
+ *
+ *  All Fast PWMs have a 50Hz rate.
+ *
+ *  The following pins/signals use the direct method. All other pins use the
+ *  the interrupt method. Note that SERVO2_PIN and RAMPS_D8_PIN use the
+ *  interrupt method.
+ *
+ *     P1_20 (11)   SERVO0_PIN
+ *     P1_21 ( 6)   SERVO1_PIN       J5-1
+ *     P0_18 ( 4)   SERVO3_PIN       5V output
+ *    *P2_04 ( 9)   RAMPS_D9_PIN
+ *    *P2_05 (10)   RAMPS_D10_PIN
+ *
+ *    * - If used as a heater driver then a Fast PWM is NOT assigned. If used as
+ *        a fan driver then enabling FAST_PWM_FAN assigns a Fast PWM to it.
+ */
+
+ /**
+  * Special pins
+  *   P1_30  (37) (NOT 5V tolerant)
+  *   P1_31  (49) (NOT 5V tolerant)
+  *   P0_27  (57) (Open collector)
+  *   P0_28  (58) (Open collector)
+  */
+
+/**
+ *  The following mega2560 pins are NOT available in a Re-ARM system:
+ *
+ *  7, 17, 22, 23, 25, 27, 29, 32, 39, 40, 42, 43, 44, 45, 47, 64, 65, 66
+ */