diff options
Diffstat (limited to 'Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h')
| -rw-r--r-- | Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h | 518 |
1 files changed, 518 insertions, 0 deletions
diff --git a/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h b/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h new file mode 100644 index 0000000..6584030 --- /dev/null +++ b/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h @@ -0,0 +1,518 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Re-ARM with RAMPS v1.4 pin assignments + * + * Applies to the following boards: + * + * RAMPS_14_EFB (Hotend, Fan, Bed) + * RAMPS_14_EEB (Hotend0, Hotend1, Bed) + * RAMPS_14_EFF (Hotend, Fan0, Fan1) + * RAMPS_14_EEF (Hotend0, Hotend1, Fan) + * RAMPS_14_SF (Spindle, Controller Fan) + */ + +// Numbers in parentheses () are the corresponding mega2560 pin numbers + +#if NOT_TARGET(MCU_LPC1768) + #error "Oops! Make sure you have the LPC1768 environment selected in your IDE." +#endif + +#define BOARD_INFO_NAME "Re-ARM RAMPS 1.4" + +// +// Servos +// +#define SERVO0_PIN P1_20 // (11) +#define SERVO1_PIN P1_21 // ( 6) also on J5-1 +#define SERVO2_PIN P1_19 // ( 5) +#define SERVO3_PIN P1_18 // ( 4) 5V output + +// +// Limit Switches +// +#define X_MIN_PIN P1_24 // ( 3) 10k pullup to 3.3V, 1K series +#define X_MAX_PIN P1_25 // ( 2) 10k pullup to 3.3V, 1K series +#define Y_MIN_PIN P1_26 // (14) 10k pullup to 3.3V, 1K series +#define Y_MAX_PIN P1_27 // (15) 10k pullup to 3.3V, 1K series +#define Z_MIN_PIN P1_29 // (18) 10k pullup to 3.3V, 1K series +#define Z_MAX_PIN P1_28 // (19) 10k pullup to 3.3V, 1K series +#define ONBOARD_ENDSTOPPULLUPS // Board has built-in pullups + +// +// Steppers +// +#define X_STEP_PIN P2_01 // (54) +#define X_DIR_PIN P0_11 // (55) +#define X_ENABLE_PIN P0_10 // (38) +#ifndef X_CS_PIN + #define X_CS_PIN P1_01 // ETH +#endif + +#define Y_STEP_PIN P2_02 // (60) +#define Y_DIR_PIN P0_20 // (61) +#define Y_ENABLE_PIN P0_19 // (56) +#ifndef Y_CS_PIN + #define Y_CS_PIN P1_04 // ETH +#endif + +#define Z_STEP_PIN P2_03 // (46) +#define Z_DIR_PIN P0_22 // (48) +#define Z_ENABLE_PIN P0_21 // (62) +#ifndef Z_CS_PIN + #define Z_CS_PIN P1_10 // ETH +#endif + +#define E0_STEP_PIN P2_00 // (26) +#define E0_DIR_PIN P0_05 // (28) +#define E0_ENABLE_PIN P0_04 // (24) +#ifndef E0_CS_PIN + #define E0_CS_PIN P1_14 // ETH +#endif + +#define E1_STEP_PIN P2_08 // (36) +#define E1_DIR_PIN P2_13 // (34) +#define E1_ENABLE_PIN P4_29 // (30) +#ifndef E1_CS_PIN + #define E1_CS_PIN -1 +#endif + +// +// Software SPI pins for TMC2130 stepper drivers +// +#if ENABLED(TMC_USE_SW_SPI) + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI P1_00 // ETH + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO P1_08 // ETH + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK P1_09 // ETH + #endif +#endif + +#if HAS_TMC_UART + /** + * TMC2208/TMC2209 stepper drivers + * + * Hardware serial communication ports. + * If undefined software serial is used according to the pins below + */ + + // + // Software serial + // + + // P2_08 E1-Step + // P2_13 E1-Dir + + #ifndef X_SERIAL_TX_PIN + #define X_SERIAL_TX_PIN P0_01 + #endif + #ifndef X_SERIAL_RX_PIN + #define X_SERIAL_RX_PIN P0_01 + #endif + + #ifndef Y_SERIAL_TX_PIN + #define Y_SERIAL_TX_PIN P0_00 + #endif + #ifndef Y_SERIAL_RX_PIN + #define Y_SERIAL_RX_PIN P0_00 + #endif + + #ifndef Z_SERIAL_TX_PIN + #define Z_SERIAL_TX_PIN P2_13 + #endif + #ifndef Z_SERIAL_RX_PIN + #define Z_SERIAL_RX_PIN P2_13 + #endif + + #ifndef E0_SERIAL_TX_PIN + #define E0_SERIAL_TX_PIN P2_08 + #endif + #ifndef E0_SERIAL_RX_PIN + #define E0_SERIAL_RX_PIN P2_08 + #endif + + // Reduce baud rate to improve software serial reliability + #define TMC_BAUD_RATE 19200 +#endif + +// +// Temperature Sensors +// 3.3V max when defined as an analog input +// +#define TEMP_0_PIN P0_23_A0 // A0 (T0) - (67) - TEMP_0_PIN +#define TEMP_BED_PIN P0_24_A1 // A1 (T1) - (68) - TEMP_BED_PIN +#define TEMP_1_PIN P0_25_A2 // A2 (T2) - (69) - TEMP_1_PIN +#define TEMP_2_PIN P0_26_A3 // A3 - (63) - J5-3 & AUX-2 +#define TEMP_3_PIN P1_30_A4 // A4 - (37) - BUZZER_PIN +//#define TEMP_4_PIN P1_31_A5 // A5 - (49) - SD_DETECT_PIN +//#define ?? P0_03_A6 // A6 - ( 0) - RXD0 - J4-4 & AUX-1 +#define FILWIDTH_PIN P0_02_A7 // A7 - ( 1) - TXD0 - J4-5 & AUX-1 + +// +// Augmentation for auto-assigning RAMPS plugs +// +#if NONE(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) + #if HAS_MULTI_HOTEND + #if TEMP_SENSOR_BED + #define IS_RAMPS_EEB + #else + #define IS_RAMPS_EEF + #endif + #elif TEMP_SENSOR_BED + #define IS_RAMPS_EFB + #else + #define IS_RAMPS_EFF + #endif +#endif + +// +// Heaters / Fans +// +#ifndef MOSFET_D_PIN + #define MOSFET_D_PIN -1 +#endif +#ifndef RAMPS_D8_PIN + #define RAMPS_D8_PIN P2_07 // (8) +#endif +#ifndef RAMPS_D9_PIN + #define RAMPS_D9_PIN P2_04 // (9) +#endif +#ifndef RAMPS_D10_PIN + #define RAMPS_D10_PIN P2_05 // (10) +#endif + +#define HEATER_0_PIN RAMPS_D10_PIN + +#if ENABLED(IS_RAMPS_EFB) // Hotend, Fan, Bed + #define HEATER_BED_PIN RAMPS_D8_PIN +#elif ENABLED(IS_RAMPS_EEF) // Hotend, Hotend, Fan + #define HEATER_1_PIN RAMPS_D9_PIN +#elif ENABLED(IS_RAMPS_EEB) // Hotend, Hotend, Bed + #define HEATER_1_PIN RAMPS_D9_PIN + #define HEATER_BED_PIN RAMPS_D8_PIN +#elif ENABLED(IS_RAMPS_EFF) // Hotend, Fan, Fan + #define FAN1_PIN RAMPS_D8_PIN +#elif DISABLED(IS_RAMPS_SF) // Not Spindle, Fan (i.e., "EFBF" or "EFBE") + #define HEATER_BED_PIN RAMPS_D8_PIN + #if HOTENDS == 1 + #define FAN1_PIN MOSFET_D_PIN + #else + #define HEATER_1_PIN MOSFET_D_PIN + #endif +#endif + +#ifndef FAN_PIN + #if EITHER(IS_RAMPS_EFB, IS_RAMPS_EFF) // Hotend, Fan, Bed or Hotend, Fan, Fan + #define FAN_PIN RAMPS_D9_PIN + #elif EITHER(IS_RAMPS_EEF, IS_RAMPS_SF) // Hotend, Hotend, Fan or Spindle, Fan + #define FAN_PIN RAMPS_D8_PIN + #elif ENABLED(IS_RAMPS_EEB) // Hotend, Hotend, Bed + #define FAN_PIN P1_18 // (4) IO pin. Buffer needed + #else // Non-specific are "EFB" (i.e., "EFBF" or "EFBE") + #define FAN_PIN RAMPS_D9_PIN + #endif +#endif + +// +// Misc. Functions +// +#define LED_PIN P4_28 // (13) + +// define digital pin 5 for the filament runout sensor. Use the RAMPS 1.4 digital input 5 on the servos connector +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN P1_19 // (5) +#endif + +#define PS_ON_PIN P2_12 // (12) + +#if !defined(MAX6675_SS_PIN) && DISABLED(USE_ZMAX_PLUG) + #define MAX6675_SS_PIN P1_28 +#endif + +#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENA_PIN) + #if !defined(NUM_SERVOS) || NUM_SERVOS < 4 // Try to use servo connector + #define CASE_LIGHT_PIN P1_18 // (4) MUST BE HARDWARE PWM + #endif +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// Use servo pins, if available +// +#if HAS_CUTTER && !PIN_EXISTS(SPINDLE_LASER_ENA) + #if NUM_SERVOS > 1 + #if ENABLED(SPINDLE_FEATURE) + #error "SPINDLE_FEATURE requires 3 free servo pins." + #else + #error "LASER_FEATURE requires 3 free servo pins." + #endif + #endif + #define SPINDLE_LASER_ENA_PIN SERVO1_PIN // (6) Pin should have a pullup/pulldown! + #define SPINDLE_LASER_PWM_PIN SERVO3_PIN // (4) MUST BE HARDWARE PWM + #define SPINDLE_DIR_PIN SERVO2_PIN // (5) +#endif + +// +// Průša i3 MK2 Multiplexer Support +// +#if SERIAL_PORT != 0 && SERIAL_PORT_2 != 0 + #define E_MUX0_PIN P0_03 // ( 0) Z_CS_PIN + #define E_MUX1_PIN P0_02 // ( 1) E0_CS_PIN +#endif +#define E_MUX2_PIN P0_26 // (63) E1_CS_PIN + +/** + * LCD / Controller + * + * All controllers can use J3 and J5 on the Re-ARM board. Custom cabling will be required. + * + * - https://github.com/wolfmanjm/universal-panel-adapter + * - https://panucattdevices.freshdesk.com/support/solutions/articles/1000243195-lcd-display-installation + */ + +/** + * Smart LCD adapter + * + * The Smart LCD adapter can be used for the two 10 pin LCD controllers such as + * REPRAP_DISCOUNT_SMART_CONTROLLER. It can't be used for controllers that use + * DOGLCD_A0, DOGLCD_CS, LCD_PINS_D5, LCD_PINS_D6 or LCD_PINS_D7. A custom cable + * is needed to pick up 5V for the EXP1 connection. + * + * SD card on the LCD uses the same SPI signals as the LCD. This results in garbage/lines + * on the LCD display during accesses of the SD card. The menus/code has been arranged so + * that the garbage/lines are erased immediately after the SD card accesses are completed. + */ + +#if ENABLED(CR10_STOCKDISPLAY) + + // Re-Arm can support Creality stock display without SD card reader and single cable on EXP3. + // Re-Arm J3 pins 1 (p1.31) & 2 (P3.26) are not used. Stock cable will need to have one + // 10-pin IDC connector trimmed or replaced with a 12-pin IDC connector to fit J3. + // Requires REVERSE_ENCODER_DIRECTION in Configuration.h + + #define BEEPER_PIN P2_11 // J3-3 & AUX-4 + + #define BTN_EN1 P0_16 // J3-7 & AUX-4 + #define BTN_EN2 P1_23 // J3-5 & AUX-4 + #define BTN_ENC P3_25 // J3-4 & AUX-4 + + #define LCD_PINS_RS P0_15 // J3-9 & AUX-4 (CS) + #define LCD_PINS_ENABLE P0_18 // J3-10 & AUX-3 (SID, MOSI) + #define LCD_PINS_D4 P2_06 // J3-8 & AUX-3 (SCK, CLK) + +#elif ENABLED(ZONESTAR_LCD) + + #error "CAUTION! ZONESTAR_LCD on REARM requires wiring modifications. NB. ADCs are not 5V tolerant. Comment out this line to continue." + +#elif IS_TFTGLCD_PANEL + + #if ENABLED(TFTGLCD_PANEL_SPI) + #define TFTGLCD_CS P3_26 // (31) J3-2 & AUX-4 + #endif + + #define SD_DETECT_PIN P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant) + #define KILL_PIN P1_22 // (41) J5-4 & AUX-4 + +#elif HAS_WIRED_LCD + + #if ENABLED(FYSETC_MINI_12864) + #define BEEPER_PIN P1_01 + #define BTN_ENC P1_04 + #else + #define BEEPER_PIN P1_30 // (37) not 5V tolerant + #define BTN_ENC P2_11 // (35) J3-3 & AUX-4 + #endif + + #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4 + #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 + + #define SD_DETECT_PIN P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant) + #define KILL_PIN P1_22 // (41) J5-4 & AUX-4 + #define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4 + #define LCD_SDSS P1_23 // (53) J3-5 & AUX-3 + + #if IS_NEWPANEL + #if IS_RRW_KEYPAD + #define SHIFT_OUT_PIN P0_18 // (51) (MOSI) J3-10 & AUX-3 + #define SHIFT_CLK_PIN P0_15 // (52) (SCK) J3-9 & AUX-3 + #define SHIFT_LD_PIN P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant) + #endif + #else + //#define SHIFT_CLK_PIN P3_26 // (31) J3-2 & AUX-4 + //#define SHIFT_LD_PIN P3_25 // (33) J3-4 & AUX-4 + //#define SHIFT_OUT_PIN P2_11 // (35) J3-3 & AUX-4 + //#define SHIFT_EN_PIN P1_22 // (41) J5-4 & AUX-4 + #endif + + #if ANY(VIKI2, miniVIKI) + //#define LCD_SCREEN_ROT_180 + + #define DOGLCD_CS P0_16 // (16) + #define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2 + #define DOGLCD_SCK SD_SCK_PIN + #define DOGLCD_MOSI SD_MOSI_PIN + + #define STAT_LED_BLUE_PIN P0_26 // (63) may change if cable changes + #define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes + + #else + + #if ENABLED(FYSETC_MINI_12864) + #define DOGLCD_SCK P0_15 + #define DOGLCD_MOSI P0_18 + + // EXP1 on LCD adapter is not usable - using Ethernet connector instead + #define DOGLCD_CS P1_09 + #define DOGLCD_A0 P1_14 + //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems + // results in LCD soft SPI mode 3, SD soft SPI mode 0 + + #define LCD_RESET_PIN P0_16 // Must be high or open for LCD to operate normally. + + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN P1_00 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN P1_01 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN P1_08 + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #define NEOPIXEL_PIN P1_00 + #endif + #else + #define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2 + #define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2 + #endif + + #define LCD_BACKLIGHT_PIN P0_16 //(16) J3-7 & AUX-4 - only used on DOGLCD controllers + #define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3 + #define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3 + #if IS_ULTIPANEL + #define LCD_PINS_D5 P1_17 // (71) ENET_MDIO + #define LCD_PINS_D6 P1_14 // (73) ENET_RX_ER + #define LCD_PINS_D7 P1_10 // (75) ENET_RXD1 + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + + #endif + #endif + + #if ENABLED(MINIPANEL) + // GLCD features + // Uncomment screen orientation + //#define LCD_SCREEN_ROT_90 + //#define LCD_SCREEN_ROT_180 + //#define LCD_SCREEN_ROT_270 + #endif + +#endif // HAS_WIRED_LCD + +// +// Ethernet pins +// +#if !IS_ULTIPANEL + #define ENET_MDIO P1_17 // (71) J12-4 + #define ENET_RX_ER P1_14 // (73) J12-6 + #define ENET_RXD1 P1_10 // (75) J12-8 +#endif +#define ENET_MOC P1_16 // (70) J12-3 +#define REF_CLK P1_15 // (72) J12-5 +#define ENET_RXD0 P1_09 // (74) J12-7 +#define ENET_CRS P1_08 // (76) J12-9 +#define ENET_TX_EN P1_04 // (77) J12-10 +#define ENET_TXD0 P1_00 // (78) J12-11 +#define ENET_TXD1 P1_01 // (79) J12-12 + +// +// SD Support +// +#ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION ONBOARD +#endif + +#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card + +#if SD_CONNECTION_IS(LCD) + #define SD_SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3 + #define SD_MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3 + #define SD_MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3 + #define SD_SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS) - CS used by Marlin +#elif SD_CONNECTION_IS(ONBOARD) + #undef SD_DETECT_PIN + #define SD_SCK_PIN P0_07 + #define SD_MISO_PIN P0_08 + #define SD_MOSI_PIN P0_09 + #define SD_SS_PIN ONBOARD_SD_CS_PIN +#elif SD_CONNECTION_IS(CUSTOM_CABLE) + #error "No custom SD drive cable defined for this board." +#endif + +/** + * Fast PWMs + * + * The LPC1768's hardware PWM controller has 6 channels. Each channel + * can be setup to either control a dedicated pin directly or to generate + * an interrupt. The direct method's duty cycle is accurate to within a + * a microsecond. The interrupt method's average duty cycle has the + * the same accuracy but the individual cycles can vary because of higher + * priority interrupts. + * + * All Fast PWMs have a 50Hz rate. + * + * The following pins/signals use the direct method. All other pins use the + * the interrupt method. Note that SERVO2_PIN and RAMPS_D8_PIN use the + * interrupt method. + * + * P1_20 (11) SERVO0_PIN + * P1_21 ( 6) SERVO1_PIN J5-1 + * P0_18 ( 4) SERVO3_PIN 5V output + * *P2_04 ( 9) RAMPS_D9_PIN + * *P2_05 (10) RAMPS_D10_PIN + * + * * - If used as a heater driver then a Fast PWM is NOT assigned. If used as + * a fan driver then enabling FAST_PWM_FAN assigns a Fast PWM to it. + */ + + /** + * Special pins + * P1_30 (37) (NOT 5V tolerant) + * P1_31 (49) (NOT 5V tolerant) + * P0_27 (57) (Open collector) + * P0_28 (58) (Open collector) + */ + +/** + * The following mega2560 pins are NOT available in a Re-ARM system: + * + * 7, 17, 22, 23, 25, 27, 29, 32, 39, 40, 42, 43, 44, 45, 47, 64, 65, 66 + */ |