Initial commit

1 files changed, 196 insertions, 0 deletions

diff --git a/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h b/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h
new file mode 100644
index 0000000..2ca2cc9
--- /dev/null
+++ b/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h
@@ -0,0 +1,196 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+/**
+ * Einsy-Rambo pin assignments
+ */
+
+#if NOT_TARGET(__AVR_ATmega2560__)
+  #error "Oops! Select 'Arduino Mega 2560 or Rambo' in 'Tools > Board.'"
+#endif
+
+#define BOARD_INFO_NAME "Einsy Rambo"
+
+//
+// TMC2130 Configuration_adv defaults for EinsyRambo
+//
+#if !AXIS_DRIVER_TYPE_X(TMC2130) || !AXIS_DRIVER_TYPE_Y(TMC2130) || !AXIS_DRIVER_TYPE_Z(TMC2130) || !AXIS_DRIVER_TYPE_E0(TMC2130)
+  #error "You must set ([XYZ]|E0)_DRIVER_TYPE to TMC2130 in Configuration.h for EinsyRambo."
+#endif
+
+// TMC2130 Diag Pins (currently just for reference)
+#define X_DIAG_PIN                            64
+#define Y_DIAG_PIN                            69
+#define Z_DIAG_PIN                            68
+#define E0_DIAG_PIN                           65
+
+//
+// Limit Switches
+//
+// Only use Diag Pins when SENSORLESS_HOMING is enabled for the TMC2130 drivers.
+// Otherwise use a physical endstop based configuration.
+//
+// SERVO0_PIN and Z_MIN_PIN configuration for BLTOUCH sensor when combined with SENSORLESS_HOMING.
+//
+
+#if DISABLED(SENSORLESS_HOMING)
+
+  #define X_STOP_PIN                          12
+  #define Y_STOP_PIN                          11
+  #define Z_STOP_PIN                          10
+
+#else
+
+  #define X_STOP_PIN                  X_DIAG_PIN
+  #define Y_STOP_PIN                  Y_DIAG_PIN
+
+  #if ENABLED(BLTOUCH)
+    #define Z_STOP_PIN                        11  // Y-MIN
+    #define SERVO0_PIN                        10  // Z-MIN
+  #else
+    #define Z_STOP_PIN                        10
+  #endif
+
+#endif
+
+//
+// Z Probe (when not Z_MIN_PIN)
+//
+#ifndef Z_MIN_PROBE_PIN
+  #define Z_MIN_PROBE_PIN                     10
+#endif
+
+//
+// Filament Runout Sensor
+//
+#ifndef FIL_RUNOUT_PIN
+  #define FIL_RUNOUT_PIN                      62
+#endif
+
+//
+// Steppers
+//
+#define X_STEP_PIN                            37
+#define X_DIR_PIN                             49
+#define X_ENABLE_PIN                          29
+#define X_CS_PIN                              41
+
+#define Y_STEP_PIN                            36
+#define Y_DIR_PIN                             48
+#define Y_ENABLE_PIN                          28
+#define Y_CS_PIN                              39
+
+#define Z_STEP_PIN                            35
+#define Z_DIR_PIN                             47
+#define Z_ENABLE_PIN                          27
+#define Z_CS_PIN                              67
+
+#define E0_STEP_PIN                           34
+#define E0_DIR_PIN                            43
+#define E0_ENABLE_PIN                         26
+#define E0_CS_PIN                             66
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN                             0  // Analog Input
+#define TEMP_1_PIN                             1  // Analog Input
+#define TEMP_BED_PIN                           2  // Analog Input
+#define TEMP_PROBE_PIN                         3  // Analog Input
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN                           3
+#define HEATER_BED_PIN                         4
+
+#ifndef FAN_PIN
+  #define FAN_PIN                              8
+#endif
+
+#ifndef FAN1_PIN
+  #define FAN1_PIN                             6
+#endif
+
+//
+// Misc. Functions
+//
+#define SDSS                                  77
+#define LED_PIN                               13
+
+#ifndef CASE_LIGHT_PIN
+  #define CASE_LIGHT_PIN                       9
+#endif
+
+//
+// M3/M4/M5 - Spindle/Laser Control
+//
+// use P1 connector for spindle pins
+#define SPINDLE_LASER_PWM_PIN                  9  // Hardware PWM
+#define SPINDLE_LASER_ENA_PIN                 18  // Pullup!
+#define SPINDLE_DIR_PIN                       19
+
+//
+// Průša i3 MK2 Multiplexer Support
+//
+#define E_MUX0_PIN                            17
+#define E_MUX1_PIN                            16
+#define E_MUX2_PIN                            78  // 84 in MK2 Firmware, with BEEPER as 78
+
+//
+// LCD / Controller
+//
+#if HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL
+
+  #define KILL_PIN                            32
+
+  #if IS_ULTIPANEL || TOUCH_UI_ULTIPANEL
+
+    #if ENABLED(CR10_STOCKDISPLAY)
+      #define LCD_PINS_RS                     85
+      #define LCD_PINS_ENABLE                 71
+      #define LCD_PINS_D4                     70
+      #define BTN_EN1                         61
+      #define BTN_EN2                         59
+    #else
+      #define LCD_PINS_RS                     82
+      #define LCD_PINS_ENABLE                 61
+      #define LCD_PINS_D4                     59
+      #define LCD_PINS_D5                     70
+      #define LCD_PINS_D6                     85
+      #define LCD_PINS_D7                     71
+      #define BTN_EN1                         14
+      #define BTN_EN2                         72
+
+      #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
+        #define BTN_ENC_EN           LCD_PINS_D7  // Detect the presence of the encoder
+      #endif
+
+    #endif
+
+    #define BTN_ENC                            9  // AUX-2
+    #define BEEPER_PIN                        84  // AUX-4
+    #define SD_DETECT_PIN                     15
+
+  #endif // IS_ULTIPANEL || TOUCH_UI_ULTIPANEL
+#endif // HAS_WIRED_LCD