diff options
Diffstat (limited to 'Marlin/src/pins/rambo/pins_EINSY_RAMBO.h')
| -rw-r--r-- | Marlin/src/pins/rambo/pins_EINSY_RAMBO.h | 196 |
1 files changed, 196 insertions, 0 deletions
diff --git a/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h b/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h new file mode 100644 index 0000000..2ca2cc9 --- /dev/null +++ b/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h @@ -0,0 +1,196 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Einsy-Rambo pin assignments + */ + +#if NOT_TARGET(__AVR_ATmega2560__) + #error "Oops! Select 'Arduino Mega 2560 or Rambo' in 'Tools > Board.'" +#endif + +#define BOARD_INFO_NAME "Einsy Rambo" + +// +// TMC2130 Configuration_adv defaults for EinsyRambo +// +#if !AXIS_DRIVER_TYPE_X(TMC2130) || !AXIS_DRIVER_TYPE_Y(TMC2130) || !AXIS_DRIVER_TYPE_Z(TMC2130) || !AXIS_DRIVER_TYPE_E0(TMC2130) + #error "You must set ([XYZ]|E0)_DRIVER_TYPE to TMC2130 in Configuration.h for EinsyRambo." +#endif + +// TMC2130 Diag Pins (currently just for reference) +#define X_DIAG_PIN 64 +#define Y_DIAG_PIN 69 +#define Z_DIAG_PIN 68 +#define E0_DIAG_PIN 65 + +// +// Limit Switches +// +// Only use Diag Pins when SENSORLESS_HOMING is enabled for the TMC2130 drivers. +// Otherwise use a physical endstop based configuration. +// +// SERVO0_PIN and Z_MIN_PIN configuration for BLTOUCH sensor when combined with SENSORLESS_HOMING. +// + +#if DISABLED(SENSORLESS_HOMING) + + #define X_STOP_PIN 12 + #define Y_STOP_PIN 11 + #define Z_STOP_PIN 10 + +#else + + #define X_STOP_PIN X_DIAG_PIN + #define Y_STOP_PIN Y_DIAG_PIN + + #if ENABLED(BLTOUCH) + #define Z_STOP_PIN 11 // Y-MIN + #define SERVO0_PIN 10 // Z-MIN + #else + #define Z_STOP_PIN 10 + #endif + +#endif + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 10 +#endif + +// +// Filament Runout Sensor +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN 62 +#endif + +// +// Steppers +// +#define X_STEP_PIN 37 +#define X_DIR_PIN 49 +#define X_ENABLE_PIN 29 +#define X_CS_PIN 41 + +#define Y_STEP_PIN 36 +#define Y_DIR_PIN 48 +#define Y_ENABLE_PIN 28 +#define Y_CS_PIN 39 + +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 47 +#define Z_ENABLE_PIN 27 +#define Z_CS_PIN 67 + +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 26 +#define E0_CS_PIN 66 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // Analog Input +#define TEMP_1_PIN 1 // Analog Input +#define TEMP_BED_PIN 2 // Analog Input +#define TEMP_PROBE_PIN 3 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 3 +#define HEATER_BED_PIN 4 + +#ifndef FAN_PIN + #define FAN_PIN 8 +#endif + +#ifndef FAN1_PIN + #define FAN1_PIN 6 +#endif + +// +// Misc. Functions +// +#define SDSS 77 +#define LED_PIN 13 + +#ifndef CASE_LIGHT_PIN + #define CASE_LIGHT_PIN 9 +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +// use P1 connector for spindle pins +#define SPINDLE_LASER_PWM_PIN 9 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 18 // Pullup! +#define SPINDLE_DIR_PIN 19 + +// +// Průša i3 MK2 Multiplexer Support +// +#define E_MUX0_PIN 17 +#define E_MUX1_PIN 16 +#define E_MUX2_PIN 78 // 84 in MK2 Firmware, with BEEPER as 78 + +// +// LCD / Controller +// +#if HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL + + #define KILL_PIN 32 + + #if IS_ULTIPANEL || TOUCH_UI_ULTIPANEL + + #if ENABLED(CR10_STOCKDISPLAY) + #define LCD_PINS_RS 85 + #define LCD_PINS_ENABLE 71 + #define LCD_PINS_D4 70 + #define BTN_EN1 61 + #define BTN_EN2 59 + #else + #define LCD_PINS_RS 82 + #define LCD_PINS_ENABLE 61 + #define LCD_PINS_D4 59 + #define LCD_PINS_D5 70 + #define LCD_PINS_D6 85 + #define LCD_PINS_D7 71 + #define BTN_EN1 14 + #define BTN_EN2 72 + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + + #endif + + #define BTN_ENC 9 // AUX-2 + #define BEEPER_PIN 84 // AUX-4 + #define SD_DETECT_PIN 15 + + #endif // IS_ULTIPANEL || TOUCH_UI_ULTIPANEL +#endif // HAS_WIRED_LCD |