diff options
Diffstat (limited to 'Marlin/src/pins/mega/pins_LEAPFROG_XEED2015.h')
| -rw-r--r-- | Marlin/src/pins/mega/pins_LEAPFROG_XEED2015.h | 115 |
1 files changed, 115 insertions, 0 deletions
diff --git a/Marlin/src/pins/mega/pins_LEAPFROG_XEED2015.h b/Marlin/src/pins/mega/pins_LEAPFROG_XEED2015.h new file mode 100644 index 0000000..9c316aa --- /dev/null +++ b/Marlin/src/pins/mega/pins_LEAPFROG_XEED2015.h @@ -0,0 +1,115 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Leapfrog Xeed Driver board pin assignments + * + * This board is used by other Leapfrog printers in addition to the Xeed, + * such as the Creatr HS and Bolt. The pin assignments vary wildly between + * printer models. As such this file is currently specific to the Xeed. + */ + +#if NOT_TARGET(__AVR_ATmega2560__) + #error "Oops! Select 'Mega 2560' in 'Tools > Board.'" +#endif + +#define BOARD_INFO_NAME "Leapfrog Xeed 2015" + +// +// Limit Switches +// +#define X_STOP_PIN 47 // 'X Min' +#define Y_STOP_PIN 48 // 'Y Min' +#define Z_STOP_PIN 49 // 'Z Min' + +// +// Steppers +// The Xeed utilizes three Z-axis motors, which use the X, Y, and Z stepper connectors +// on the board. The X and Y steppers use external drivers, attached to signal-level +// Y-axis and X-axis connectors on the board, which map to distinct CPU pins from +// the on-board X/Y stepper drivers. +// + +// X-axis signal-level connector +#define X_STEP_PIN 65 +#define X_DIR_PIN 64 +#define X_ENABLE_PIN 66 // Not actually used on Xeed, could be repurposed + +// Y-axis signal-level connector +#define Y_STEP_PIN 23 +#define Y_DIR_PIN 22 +#define Y_ENABLE_PIN 24 // Not actually used on Xeed, could be repurposed + +// ZMOT connector (Front Right Z Motor) +#define Z_STEP_PIN 31 +#define Z_DIR_PIN 32 +#define Z_ENABLE_PIN 30 + +// XMOT connector (Rear Z Motor) +#define Z2_STEP_PIN 28 +#define Z2_DIR_PIN 63 +#define Z2_ENABLE_PIN 29 + +// YMOT connector (Front Left Z Motor) +#define Z3_STEP_PIN 14 +#define Z3_DIR_PIN 15 +#define Z3_ENABLE_PIN 39 + +// EMOT2 connector +#define E0_STEP_PIN 37 +#define E0_DIR_PIN 40 +#define E0_ENABLE_PIN 36 + +// EMOT connector +#define E1_STEP_PIN 34 +#define E1_DIR_PIN 35 +#define E1_ENABLE_PIN 33 + +// +// Filament runout +// +#define FIL_RUNOUT_PIN 42 // ROT2 Connector +#define FIL_RUNOUT2_PIN 44 // ROT1 Connector + +// +// Temperature Sensors +// +#define TEMP_0_PIN 15 // T3 Connector +#define TEMP_1_PIN 13 // T1 Connector +#define TEMP_BED_PIN 14 // BED Connector (Between T1 and T3) + +// +// Heaters / Fans +// +#define HEATER_0_PIN 8 // Misc Connector, pins 3 and 4 (Out2) +#define HEATER_1_PIN 9 // Misc Connector, pins 5 and 6 (Out3) +#define HEATER_BED_PIN 6 // Misc Connector, pins 9(-) and 10(+) (OutA) + +#define FAN_PIN 10 // Misc Connector, pins 7(-) and 8 (+) (Out4) + +#define LED_PIN 13 + +#define SOL1_PIN 7 // Misc Connector, pins 1(-) and 2(+) (Out1) + +// Door Closed Sensor +//#define DOOR_PIN 45 // HM1 Connector |