diff options
Diffstat (limited to 'Marlin/src/pins/ramps/pins_MKS_GEN_13.h')
| -rw-r--r-- | Marlin/src/pins/ramps/pins_MKS_GEN_13.h | 147 |
1 files changed, 147 insertions, 0 deletions
diff --git a/Marlin/src/pins/ramps/pins_MKS_GEN_13.h b/Marlin/src/pins/ramps/pins_MKS_GEN_13.h new file mode 100644 index 0000000..08dd0f4 --- /dev/null +++ b/Marlin/src/pins/ramps/pins_MKS_GEN_13.h @@ -0,0 +1,147 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Arduino Mega with RAMPS v1.4 adjusted pin assignments + * + * MKS GEN v1.3 (Extruder, Fan, Bed) + * MKS GEN v1.3 (Extruder, Extruder, Fan, Bed) + * MKS GEN v1.4 (Extruder, Fan, Bed) + * MKS GEN v1.4 (Extruder, Extruder, Fan, Bed) + */ + +#if HOTENDS > 2 || E_STEPPERS > 2 + #error "MKS GEN 1.3/1.4 supports up to 2 hotends / E-steppers. Comment out this line to continue." +#endif + +#define BOARD_INFO_NAME "MKS GEN >= v1.3" + +// +// Heaters / Fans +// +// Power outputs EFBF or EFBE +#define MOSFET_D_PIN 7 + +// +// PSU / SERVO +// +// If PSU_CONTROL is specified, always hijack Servo 3 +// +#if ENABLED(PSU_CONTROL) + #define SERVO3_PIN -1 + #define PS_ON_PIN 4 +#endif + +#include "pins_RAMPS.h" + +// +// LCD / Controller +// +#if ANY(VIKI2, miniVIKI) + /** + * VIKI2 Has two groups of wires with... + * + * +Vin + Input supply, requires 120ma for LCD and mSD card + * GND Ground Pin + * MOSI Data input for LCD and SD + * MISO Data output for SD + * SCK Clock for LCD and SD + * AO Reg. Sel for LCD + * LCS Chip Select for LCD + * SDCS Chip Select for SD + * SDCD Card Detect pin for SD + * ENCA Encoder output A + * ENCB Encoder output B + * ENCBTN Encoder button switch + * + * BTN Panel mounted button switch + * BUZZER Piezo buzzer + * BLUE-LED Blue LED ring pin (3 to 5v, mosfet buffered) + * RED-LED Red LED ring pin (3 to 5v, mosfet buffered) + * + * This configuration uses the following arrangement: + * + * EXP1 D37 = EN2 D35 = EN1 EXP2 D50 = MISO D52 = SCK + * D17 = BLUE D16 = RED D31 = ENC D53 = SDCS + * D23 = KILL D25 = BUZZ D33 = --- D51 = MOSI + * D27 = A0 D29 = LCS D49 = SDCD RST = --- + * GND = GND 5V = 5V GND = --- D41 = --- + */ + + #undef BTN_EN1 + #undef BTN_EN2 + #undef BTN_ENC + #undef DOGLCD_A0 + #undef DOGLCD_CS + #undef SD_DETECT_PIN + #undef BEEPER_PIN + #undef KILL_PIN + #undef STAT_LED_RED_PIN + #undef STAT_LED_BLUE_PIN + + // + // VIKI2 12-wire lead + // + + // orange/white SDCD + #define SD_DETECT_PIN 49 + + // white ENCA + #define BTN_EN1 35 + + // green ENCB + #define BTN_EN2 37 + + // purple ENCBTN + #define BTN_ENC 31 + + // brown A0 + #define DOGLCD_A0 27 + + // green/white LCS + #define DOGLCD_CS 29 + + // 50 gray MISO + // 51 yellow MOSI + // 52 orange SCK + + // blue SDCS + //#define SDSS 53 + + // + // VIKI2 4-wire lead + // + + // blue BTN + #define KILL_PIN 23 + + // green BUZZER + #define BEEPER_PIN 25 + + // yellow RED-LED + #define STAT_LED_RED_PIN 16 + + // white BLUE-LED + #define STAT_LED_BLUE_PIN 17 + +#endif |