diff options
Diffstat (limited to 'Marlin/src/pins/ramps/pins_TT_OSCAR.h')
| -rw-r--r-- | Marlin/src/pins/ramps/pins_TT_OSCAR.h | 519 |
1 files changed, 519 insertions, 0 deletions
diff --git a/Marlin/src/pins/ramps/pins_TT_OSCAR.h b/Marlin/src/pins/ramps/pins_TT_OSCAR.h new file mode 100644 index 0000000..ca40255 --- /dev/null +++ b/Marlin/src/pins/ramps/pins_TT_OSCAR.h @@ -0,0 +1,519 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ + +#if NOT_TARGET(__AVR_ATmega1280__, __AVR_ATmega2560__) + #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#endif + +#if HOTENDS > 5 || E_STEPPERS > 5 + #error "TTOSCAR supports up to 5 hotends / E-steppers. Comment out this line to continue." +#endif + +#define BOARD_INFO_NAME "TT OSCAR" +#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME + +// +// Servos +// +#define SERVO0_PIN 11 +#define SERVO1_PIN 12 +#define SERVO2_PIN 5 +#define SERVO3_PIN 4 + +// +// Limit Switches +// +#define X_MIN_PIN 3 +#define X_MAX_PIN 2 +#define Y_MIN_PIN 14 +#define Y_MAX_PIN 15 +#define Z_MIN_PIN 18 +#define Z_MAX_PIN 19 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN SERVO3_PIN +#endif + +// +// Steppers +// +#define X_STEP_PIN 54 +#define X_DIR_PIN 55 +#define X_ENABLE_PIN 38 +#define X_CS_PIN 57 + +#define Y_STEP_PIN 60 +#define Y_DIR_PIN 61 +#define Y_ENABLE_PIN 56 +#define Y_CS_PIN 58 + +#define Z_STEP_PIN 46 +#define Z_DIR_PIN 48 +#define Z_ENABLE_PIN 62 +#define Z_CS_PIN 53 + +#define E0_STEP_PIN 26 +#define E0_DIR_PIN 28 +#define E0_ENABLE_PIN 24 +#define E0_CS_PIN 49 + +#define E1_STEP_PIN 36 +#define E1_DIR_PIN 34 +#define E1_ENABLE_PIN 30 +#define E1_CS_PIN E0_CS_PIN + +#define E2_STEP_PIN 63 +#define E2_DIR_PIN 22 +#define E2_ENABLE_PIN 59 +#define E2_CS_PIN E0_CS_PIN + +#define E3_STEP_PIN 32 +#define E3_DIR_PIN 40 +#define E3_ENABLE_PIN 39 +#define E3_CS_PIN E0_CS_PIN + +#define E4_STEP_PIN 43 +#define E4_DIR_PIN 42 +#define E4_ENABLE_PIN 47 +#define E4_CS_PIN E0_CS_PIN + +#if HAS_TMC_UART + /** + * TMC2208/TMC2209 stepper drivers + * + * Hardware serial communication ports. + * If undefined software serial is used according to the pins below + */ + //#define X_HARDWARE_SERIAL Serial1 + //#define X2_HARDWARE_SERIAL Serial1 + //#define Y_HARDWARE_SERIAL Serial1 + //#define Y2_HARDWARE_SERIAL Serial1 + //#define Z_HARDWARE_SERIAL Serial1 + //#define Z2_HARDWARE_SERIAL Serial1 + //#define E0_HARDWARE_SERIAL Serial1 + //#define E1_HARDWARE_SERIAL Serial1 + //#define E2_HARDWARE_SERIAL Serial1 + //#define E3_HARDWARE_SERIAL Serial1 + //#define E3_HARDWARE_SERIAL Serial1 + + // + // Software serial + // + + #define X_SERIAL_TX_PIN -1 // 59 + #define X_SERIAL_RX_PIN -1 // 63 + #define X2_SERIAL_TX_PIN -1 + #define X2_SERIAL_RX_PIN -1 + + #define Y_SERIAL_TX_PIN -1 // 64 + #define Y_SERIAL_RX_PIN -1 // 40 + #define Y2_SERIAL_TX_PIN -1 + #define Y2_SERIAL_RX_PIN -1 + + #define Z_SERIAL_TX_PIN -1 // 44 + #define Z_SERIAL_RX_PIN -1 // 42 + #define Z2_SERIAL_TX_PIN -1 + #define Z2_SERIAL_RX_PIN -1 + + #define E0_SERIAL_TX_PIN -1 // 66 + #define E0_SERIAL_RX_PIN -1 // 65 + #define E1_SERIAL_TX_PIN -1 + #define E1_SERIAL_RX_PIN -1 + #define E2_SERIAL_TX_PIN -1 + #define E2_SERIAL_RX_PIN -1 + #define E3_SERIAL_TX_PIN -1 + #define E3_SERIAL_RX_PIN -1 + #define E4_SERIAL_TX_PIN -1 + #define E4_SERIAL_RX_PIN -1 + #define E5_SERIAL_RX_PIN -1 + #define E6_SERIAL_RX_PIN -1 + #define E7_SERIAL_RX_PIN -1 +#endif + +// +// Default pins for TMC software SPI +// +//#if ENABLED(TMC_USE_SW_SPI) +// #ifndef TMC_SW_MOSI +// #define TMC_SW_MOSI 66 +// #endif +// #ifndef TMC_SW_MISO +// #define TMC_SW_MISO 44 +// #endif +// #ifndef TMC_SW_SCK +// #define TMC_SW_SCK 64 +// #endif +//#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN 13 +#define TEMP_1_PIN 15 +#define TEMP_2_PIN 10 +#define TEMP_3_PIN 11 +#define TEMP_BED_PIN 14 + +#if TEMP_SENSOR_CHAMBER > 0 + #define TEMP_CHAMBER_PIN 12 +#else + #define TEMP_4_PIN 12 +#endif + +// SPI for Max6675 or Max31855 Thermocouple +//#if DISABLED(SDSUPPORT) +// #define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card +//#else +// #define MAX6675_SS_PIN 66 // Don't use 49 (SD_DETECT_PIN) +//#endif + +// +// Heaters / Fans +// +#define HEATER_0_PIN 10 +#define HEATER_1_PIN 7 +#define HEATER_2_PIN 44 +#define HEATER_BED_PIN 8 + +#define FAN_PIN 9 + +#if EXTRUDERS >= 5 + #define HEATER_4_PIN 6 +#else + #define FAN1_PIN 6 +#endif + +#if EXTRUDERS >= 4 + #define HEATER_3_PIN 45 +#else + #define FAN2_PIN 45 +#endif + +// +// Misc. Functions +// +#define SDSS 53 +#define LED_PIN 13 + +//#ifndef FILWIDTH_PIN +// #define FILWIDTH_PIN 5 // Analog Input +//#endif + +// DIO 4 (Servos plug) for the runout sensor. +//#define FIL_RUNOUT_PIN SERVO3_PIN + +#ifndef PS_ON_PIN + #define PS_ON_PIN 12 +#endif + +// +// Case Light +// +#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN) + #if !NUM_SERVOS // Prefer the servo connector + #define CASE_LIGHT_PIN 6 // Hardware PWM + #elif HAS_FREE_AUX2_PINS // Try to use AUX 2 + #define CASE_LIGHT_PIN 44 // Hardware PWM + #endif +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE) + #if !NUM_SERVOS // Prefer the servo connector + #define SPINDLE_LASER_ENABLE_PIN 4 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 6 // Hardware PWM + #define SPINDLE_DIR_PIN 5 + #elif HAS_FREE_AUX2_PINS // Try to use AUX 2 + #define SPINDLE_LASER_ENABLE_PIN 40 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM + #define SPINDLE_DIR_PIN 65 + #endif +#endif + +// +// Průša i3 MK2 Multiplexer Support +// +//#ifndef E_MUX0_PIN +// #define E_MUX0_PIN 58 // Y_CS_PIN +//#endif +//#ifndef E_MUX1_PIN +// #define E_MUX1_PIN 53 // Z_CS_PIN +//#endif +//#ifndef E_MUX2_PIN +// #define E_MUX2_PIN 49 // En_CS_PIN +//#endif + +////////////////////////// +// LCDs and Controllers // +////////////////////////// + +#if HAS_WIRED_LCD + + // + // LCD Display output pins + // + #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) + + #define LCD_PINS_RS 49 // CS chip select /SS chip slave select + #define LCD_PINS_ENABLE 51 // SID (MOSI) + #define LCD_PINS_D4 52 // SCK (CLK) clock + + #elif BOTH(IS_NEWPANEL, PANEL_ONE) + + #define LCD_PINS_RS 40 + #define LCD_PINS_ENABLE 42 + #define LCD_PINS_D4 65 + #define LCD_PINS_D5 66 + #define LCD_PINS_D6 44 + #define LCD_PINS_D7 64 + + #elif ENABLED(ZONESTAR_LCD) + + #define LCD_PINS_RS 64 + #define LCD_PINS_ENABLE 44 + #define LCD_PINS_D4 63 + #define LCD_PINS_D5 40 + #define LCD_PINS_D6 42 + #define LCD_PINS_D7 65 + #define ADC_KEYPAD_PIN 12 + + #else + + #if ENABLED(CR10_STOCKDISPLAY) + + #define LCD_PINS_RS 27 + #define LCD_PINS_ENABLE 29 + #define LCD_PINS_D4 25 + + #if !IS_NEWPANEL + #define BEEPER_PIN 37 + #endif + + #else + + #if EITHER(MKS_12864OLED, MKS_12864OLED_SSD1306) + #define LCD_PINS_DC 25 // Set as output on init + #define LCD_PINS_RS 27 // Pull low for 1s to init + // DOGM SPI LCD Support + #define DOGLCD_CS 16 + #define DOGLCD_MOSI 17 + #define DOGLCD_SCK 23 + #define DOGLCD_A0 LCD_PINS_DC + #else + #define LCD_PINS_RS 16 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #endif + + #define LCD_PINS_D7 29 + + #if !IS_NEWPANEL + #define BEEPER_PIN 33 + #endif + + #endif + + #if !IS_NEWPANEL + // Buttons attached to a shift register + // Not wired yet + //#define SHIFT_CLK_PIN 38 + //#define SHIFT_LD_PIN 42 + //#define SHIFT_OUT_PIN 40 + //#define SHIFT_EN_PIN 17 + #endif + + #endif + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + + // + // LCD Display input pins + // + #if IS_NEWPANEL + + #if IS_RRD_SC + + #define BEEPER_PIN 37 + + #if ENABLED(CR10_STOCKDISPLAY) + #define BTN_EN1 17 + #define BTN_EN2 23 + #else + #define BTN_EN1 31 + #define BTN_EN2 33 + #endif + + #define BTN_ENC 35 + #define SD_DETECT_PIN 49 + //#define KILL_PIN 41 + + #if ENABLED(BQ_LCD_SMART_CONTROLLER) + #define LCD_BACKLIGHT_PIN 39 + #endif + + #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) + + #define BTN_EN1 64 + #define BTN_EN2 59 + #define BTN_ENC 63 + #define SD_DETECT_PIN 42 + + #elif ENABLED(LCD_I2C_PANELOLU2) + + #define BTN_EN1 47 + #define BTN_EN2 43 + #define BTN_ENC 32 + #define LCD_SDSS 53 + //#define KILL_PIN 41 + + #elif ENABLED(LCD_I2C_VIKI) + + #define BTN_EN1 22 // https://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42. + #define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13. + #define BTN_ENC -1 + + #define LCD_SDSS 53 + #define SD_DETECT_PIN 49 + + #elif EITHER(VIKI2, miniVIKI) + + #define DOGLCD_CS 45 + #define DOGLCD_A0 44 + #define LCD_SCREEN_ROT_180 + + #define BEEPER_PIN 33 + #define STAT_LED_RED_PIN 32 + #define STAT_LED_BLUE_PIN 35 + + #define BTN_EN1 22 + #define BTN_EN2 7 + #define BTN_ENC 39 + + #define SDSS 53 + #define SD_DETECT_PIN -1 // Pin 49 for display SD interface, 72 for easy adapter board + //#define KILL_PIN 31 + + #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) + + #define DOGLCD_CS 29 + #define DOGLCD_A0 27 + + #define BEEPER_PIN 23 + #define LCD_BACKLIGHT_PIN 33 + + #define BTN_EN1 35 + #define BTN_EN2 37 + #define BTN_ENC 31 + + #define LCD_SDSS 53 + #define SD_DETECT_PIN 49 + //#define KILL_PIN 41 + + #elif ENABLED(MKS_MINI_12864) + + #define DOGLCD_A0 27 + #define DOGLCD_CS 25 + + // GLCD features + //#define LCD_CONTRAST_INIT 190 + // Uncomment screen orientation + //#define LCD_SCREEN_ROT_90 + //#define LCD_SCREEN_ROT_180 + //#define LCD_SCREEN_ROT_270 + + #define BEEPER_PIN 37 + + #define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65 + + #define BTN_EN1 31 + #define BTN_EN2 33 + #define BTN_ENC 35 + //#define SDSS 53 + #define SD_DETECT_PIN 49 + //#define KILL_PIN 64 + + #elif ENABLED(MINIPANEL) + + #define BEEPER_PIN 42 + // not connected to a pin + #define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65 + + #define DOGLCD_A0 44 + #define DOGLCD_CS 66 + + // GLCD features + //#define LCD_CONTRAST_INIT 190 + // Uncomment screen orientation + //#define LCD_SCREEN_ROT_90 + //#define LCD_SCREEN_ROT_180 + //#define LCD_SCREEN_ROT_270 + + #define BTN_EN1 40 + #define BTN_EN2 63 + #define BTN_ENC 59 + + #define SDSS 53 + #define SD_DETECT_PIN 49 + //#define KILL_PIN 64 + + #else + + // Beeper on AUX-4 + #define BEEPER_PIN 33 + + // Buttons are directly attached to AUX-2 + #if IS_RRW_KEYPAD + #define SHIFT_OUT_PIN 40 + #define SHIFT_CLK_PIN 44 + #define SHIFT_LD_PIN 42 + #define BTN_EN1 64 + #define BTN_EN2 59 + #define BTN_ENC 63 + #elif ENABLED(PANEL_ONE) + #define BTN_EN1 59 // AUX2 PIN 3 + #define BTN_EN2 63 // AUX2 PIN 4 + #define BTN_ENC 49 // AUX3 PIN 7 + #else + #define BTN_EN1 37 + #define BTN_EN2 35 + #define BTN_ENC 31 + #endif + + #if ENABLED(G3D_PANEL) + #define SD_DETECT_PIN 49 + //#define KILL_PIN 41 + #endif + + #endif + + #endif // IS_NEWPANEL + +#endif |