diff options
Diffstat (limited to 'Marlin/src/pins/ramps/pins_ULTIMAKER_OLD.h')
| -rw-r--r-- | Marlin/src/pins/ramps/pins_ULTIMAKER_OLD.h | 274 |
1 files changed, 274 insertions, 0 deletions
diff --git a/Marlin/src/pins/ramps/pins_ULTIMAKER_OLD.h b/Marlin/src/pins/ramps/pins_ULTIMAKER_OLD.h new file mode 100644 index 0000000..37c28ec --- /dev/null +++ b/Marlin/src/pins/ramps/pins_ULTIMAKER_OLD.h @@ -0,0 +1,274 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Ultimaker pin assignments (Old electronics) + */ + +/** + * Rev B 3 JAN 2017 + * + * Details on pin definitions for M3, M4 & M5 spindle control commands and for + * the CASE_LIGHT_PIN are at the end of this file. + * + * This started out as an attempt to add pin definitions for M3, M4 & M5 spindle + * control commands but quickly turned into a head scratcher as the sources for + * the revisions provided inconsistent information. + * + * As best I can determine: + * 1.5.3 boards should use the pins_ULTIMAKER.h file which means the BOARD_INFO_NAME + * define in this file should say 1.5.3 rather than 1.5.4 + * This file is meant for 1.1 - 1.3 boards. + * The endstops for the 1.0 boards use different definitions than on the 1.1 - 1.3 + * boards. + * + * I've added sections that have the 1.0 and 1.5.3 + endstop definitions so you can + * easily switch if needed. I've also copied over the 1.5.3 + LCD definitions. + * + * To be 100% sure of the board you have: + * 1. In Configuration_adv.h enable "PINS_DEBUGGING" + * 2. Compile & uploade + * 3. Enter the command "M43 W1 I1". This command will report that pin nmumber and + * name of any pin that changes state. + * 4. Using a 1k (approximately) resistor pull the endstops and some of the LCD pins + * to ground and see what is reported. + * 5. If the reported pin doesn't match the file then try a different board revision + * and repeat steps 2 - 5 + */ + +#define BOARD_REV_1_1_TO_1_3 +//#define BOARD_REV_1_0 +//#define BOARD_REV_1_5 + +#if NOT_TARGET(__AVR_ATmega1280__, __AVR_ATmega2560__) + #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#endif + +#ifdef BOARD_REV_1_1_TO_1_3 + #define BOARD_INFO_NAME "Ultimaker 1.1-1.3" +#elif defined(BOARD_REV_1_0) + #define BOARD_INFO_NAME "Ultimaker 1.0" +#elif defined(BOARD_REV_1_5) + #define BOARD_INFO_NAME "Ultimaker 1.5" +#else + #define BOARD_INFO_NAME "Ultimaker 1.5.4+" +#endif +#define DEFAULT_MACHINE_NAME "Ultimaker" +#define DEFAULT_SOURCE_CODE_URL "github.com/Ultimaker/Marlin" + +// +// Limit Switches +// +#if ENABLED(BOARD_REV_1_1_TO_1_3) + #define X_MIN_PIN 15 // SW1 + #define X_MAX_PIN 14 // SW2 + #define Y_MIN_PIN 17 // SW3 + #define Y_MAX_PIN 16 // SW4 + #define Z_MIN_PIN 19 // SW5 + #define Z_MAX_PIN 18 // SW6 +#endif + +#if ENABLED(BOARD_REV_1_0) + #if HAS_CUTTER + #define X_STOP_PIN 13 // SW1 (didn't change) - also has a useable hardware PWM + #define Y_STOP_PIN 12 // SW2 + #define Z_STOP_PIN 11 // SW3 + #else + #define X_MIN_PIN 13 // SW1 + #define X_MAX_PIN 12 // SW2 + #define Y_MIN_PIN 11 // SW3 + #define Y_MAX_PIN 10 // SW4 + #define Z_MIN_PIN 9 // SW5 + #define Z_MAX_PIN 8 // SW6 + #endif +#endif + +#if ENABLED(BOARD_REV_1_5) + #define X_MIN_PIN 22 + #define X_MAX_PIN 24 + #define Y_MIN_PIN 26 + #define Y_MAX_PIN 28 + #define Z_MIN_PIN 30 + #define Z_MAX_PIN 32 +#endif + +// +// Z Probe (when not Z_MIN_PIN) +// +#if !defined(Z_MIN_PROBE_PIN) && !BOTH(HAS_CUTTER, BOARD_REV_1_0) + #define Z_MIN_PROBE_PIN Z_MAX_PIN +#endif + +// +// Steppers +// +#define X_STEP_PIN 25 +#define X_DIR_PIN 23 +#define X_ENABLE_PIN 27 + +#define Y_STEP_PIN 31 +#define Y_DIR_PIN 33 +#define Y_ENABLE_PIN 29 + +#define Z_STEP_PIN 37 +#define Z_DIR_PIN 39 +#define Z_ENABLE_PIN 35 + +#if BOTH(HAS_CUTTER, BOARD_REV_1_1_TO_1_3) && EXTRUDERS == 1 + // Move E0 to the spare and get Spindle/Laser signals from E0 + #define E0_STEP_PIN 49 + #define E0_DIR_PIN 47 + #define E0_ENABLE_PIN 48 +#else + #define E0_STEP_PIN 43 + #define E0_DIR_PIN 45 + #define E0_ENABLE_PIN 41 + + #define E1_STEP_PIN 49 + #define E1_DIR_PIN 47 + #define E1_ENABLE_PIN 48 +#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN 8 // Analog Input +#define TEMP_1_PIN 1 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 2 +//#define HEATER_1_PIN 3 // used for case light Rev A said "1" +#define HEATER_BED_PIN 4 + +// +// LCD / Controller +// +#if ANY(BOARD_REV_1_0, BOARD_REV_1_1_TO_1_3) + + #define LCD_PINS_RS 24 + #define LCD_PINS_ENABLE 22 + #define LCD_PINS_D4 36 + #define LCD_PINS_D5 34 + #define LCD_PINS_D6 32 + #define LCD_PINS_D7 30 + +#elif BOTH(BOARD_REV_1_5, IS_ULTRA_LCD) + + #define BEEPER_PIN 18 + + #if IS_NEWPANEL + + #define LCD_PINS_RS 20 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 16 + #define LCD_PINS_D5 21 + #define LCD_PINS_D6 5 + #define LCD_PINS_D7 6 + + // Buttons directly attached + #define BTN_EN1 40 + #define BTN_EN2 42 + #define BTN_ENC 19 + + #define SD_DETECT_PIN 38 + + #else // !IS_NEWPANEL - Old style panel with shift register + + // Buttons attached to a shift register + #define SHIFT_CLK_PIN 38 + #define SHIFT_LD_PIN 42 + #define SHIFT_OUT_PIN 40 + #define SHIFT_EN_PIN 17 + + #define LCD_PINS_RS 16 + #define LCD_PINS_ENABLE 5 + #define LCD_PINS_D4 6 + #define LCD_PINS_D5 21 + #define LCD_PINS_D6 20 + #define LCD_PINS_D7 19 + + #endif // !IS_NEWPANEL + +#endif + +// +// case light - see spindle section for more info on available hardware PWMs +// +#if !PIN_EXISTS(CASE_LIGHT) && ENABLED(BOARD_REV_1_5) + #define CASE_LIGHT_PIN 7 // use PWM - MUST BE HARDWARE PWM +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if HAS_CUTTER + #if EITHER(BOARD_REV_1_0, BOARD_REV_1_5) // Use the last three SW positions + #define SPINDLE_DIR_PIN 10 // 1.0: SW4 1.5: EXP3-6 ("10") + #define SPINDLE_LASER_PWM_PIN 9 // 1.0: SW5 1.5: EXP3-7 ( "9") .. MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENA_PIN 8 // 1.0: SW6 1.5: EXP3-8 ( "8") .. Pin should have a pullup! + #elif ENABLED(BOARD_REV_1_1_TO_1_3) + /** + * Only four hardware PWMs physically connected to anything on these boards: + * + * HEATER_0_PIN 2 silkscreen varies - usually "PWM 1" or "HEATER1" + * HEATER_1_PIN 3 silkscreen varies - usually "PWM 2" or "HEATER2" + * HEATER_BED_PIN 4 silkscreen varies - usually "PWM 3" or "HEATED BED" + * E0_DIR_PIN 45 + * + * If one of the heaters is used then special precautions will usually be needed. + * They have an LED and resistor pullup to +24V which could damage 3.3V-5V ICs. + */ + #if EXTRUDERS == 1 + #define SPINDLE_DIR_PIN 43 + #define SPINDLE_LASER_PWM_PIN 45 // Hardware PWM + #define SPINDLE_LASER_ENA_PIN 41 // Pullup! + #elif TEMP_SENSOR_BED == 0 // Can't use E0 so see if HEATER_BED_PIN is available + #undef HEATER_BED_PIN + #define SPINDLE_DIR_PIN 38 // Probably pin 4 on 10 pin connector closest to the E0 socket + #define SPINDLE_LASER_PWM_PIN 4 // Hardware PWM - Special precautions usually needed. + #define SPINDLE_LASER_ENA_PIN 40 // Pullup! (Probably pin 6 on the 10-pin + // connector closest to the E0 socket) + #endif + #endif +#endif + +/** + * Where to get the spindle signals on the E0 socket + * + * spindle signal socket name socket name + * ------- + * SPINDLE_LASER_ENA_PIN /ENABLE *| |O VMOT + * MS1 O| |O GND + * MS2 O| |O 2B + * MS3 O| |O 2A + * /RESET O| |O 1A + * /SLEEP O| |O 1B + * SPINDLE_DIR_PIN STEP O| |O VDD + * SPINDLE_LASER_PWM_PIN DIR O| |O GND + * ------- + * * - pin closest to MS1, MS2 & MS3 jumpers on the board + * + * Note: Socket names vary from vendor to vendor. + */ |