diff options
Diffstat (limited to 'Marlin/src/pins/sam/pins_RAMPS_FD_V1.h')
| -rw-r--r-- | Marlin/src/pins/sam/pins_RAMPS_FD_V1.h | 239 |
1 files changed, 239 insertions, 0 deletions
diff --git a/Marlin/src/pins/sam/pins_RAMPS_FD_V1.h b/Marlin/src/pins/sam/pins_RAMPS_FD_V1.h new file mode 100644 index 0000000..80e8f0d --- /dev/null +++ b/Marlin/src/pins/sam/pins_RAMPS_FD_V1.h @@ -0,0 +1,239 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * RAMPS-FD + * + * No EEPROM + * Use 4k7 thermistor tables + */ + +#if NOT_TARGET(__SAM3X8E__) + #error "Oops! Select 'Arduino Due' in 'Tools > Board.'" +#endif + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "RAMPS-FD v1" +#endif + +#define INVERTED_HEATER_PINS +#define INVERTED_BED_PINS +#define INVERTED_FAN_PINS + +// +// Servos +// +#define SERVO0_PIN 7 +#define SERVO1_PIN 6 +#define SERVO2_PIN 5 +#define SERVO3_PIN 3 + +// +// Limit Switches +// +#define X_MIN_PIN 22 +#define X_MAX_PIN 30 +#define Y_MIN_PIN 24 +#define Y_MAX_PIN 38 +#define Z_MIN_PIN 26 +#define Z_MAX_PIN 34 + +// +// Steppers +// +#define X_STEP_PIN 63 +#define X_DIR_PIN 62 +#define X_ENABLE_PIN 48 +#ifndef X_CS_PIN + #define X_CS_PIN 68 +#endif + +#define Y_STEP_PIN 65 +#define Y_DIR_PIN 64 +#define Y_ENABLE_PIN 46 +#ifndef Y_CS_PIN + #define Y_CS_PIN 60 +#endif + +#define Z_STEP_PIN 67 +#define Z_DIR_PIN 66 +#define Z_ENABLE_PIN 44 +#ifndef Z_CS_PIN + #define Z_CS_PIN 58 +#endif + +#define E0_STEP_PIN 36 +#define E0_DIR_PIN 28 +#define E0_ENABLE_PIN 42 +#ifndef E0_CS_PIN + #define E0_CS_PIN 67 +#endif + +#define E1_STEP_PIN 43 +#define E1_DIR_PIN 41 +#define E1_ENABLE_PIN 39 +#ifndef E1_CS_PIN + #define E1_CS_PIN 61 +#endif + +#define E2_STEP_PIN 32 +#define E2_DIR_PIN 47 +#define E2_ENABLE_PIN 45 +#ifndef E2_CS_PIN + #define E2_CS_PIN 59 +#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN 1 // Analog Input +#define TEMP_1_PIN 2 // Analog Input +#define TEMP_2_PIN 3 // Analog Input +#define TEMP_BED_PIN 0 // Analog Input + +// SPI for Max6675 or Max31855 Thermocouple +#if DISABLED(SDSUPPORT) + #define MAX6675_SS_PIN 53 +#else + #define MAX6675_SS_PIN 49 +#endif + +// +// Heaters / Fans +// +#define HEATER_0_PIN 9 +#define HEATER_1_PIN 10 +#define HEATER_2_PIN 11 +#define HEATER_BED_PIN 8 + +#ifndef FAN_PIN + #define FAN_PIN 12 +#endif + +// +// Misc. Functions +// +#define SDSS 4 +#define LED_PIN 13 + +// +// LCD / Controller +// +#if HAS_WIRED_LCD + // ramps-fd lcd adaptor + + #define BEEPER_PIN 37 + #define BTN_EN1 33 + #define BTN_EN2 31 + #define BTN_ENC 35 + #define SD_DETECT_PIN 49 + + #if IS_NEWPANEL + #define LCD_PINS_RS 16 + #define LCD_PINS_ENABLE 17 + #endif + + #if ENABLED(FYSETC_MINI_12864) + #define DOGLCD_CS LCD_PINS_ENABLE + #define DOGLCD_A0 LCD_PINS_RS + #define DOGLCD_SCK 76 + #define DOGLCD_MOSI 75 + + //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems + // results in LCD soft SPI mode 3, SD soft SPI mode 0 + + #define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally. + + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 25 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 27 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 29 + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #define NEOPIXEL_PIN 25 + #endif + + #elif IS_NEWPANEL + + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #define LCD_PINS_D7 29 + + #if ENABLED(MINIPANEL) + #define DOGLCD_CS 25 + #define DOGLCD_A0 27 + #endif + + #endif + + #if ANY(VIKI2, miniVIKI) + #define DOGLCD_A0 16 + #define KILL_PIN 51 + #define STAT_LED_BLUE_PIN 29 + #define STAT_LED_RED_PIN 23 + #define DOGLCD_CS 17 + #define DOGLCD_SCK 76 // SCK_PIN - Required for DUE Hardware SPI + #define DOGLCD_MOSI 75 // MOSI_PIN + #define DOGLCD_MISO 74 // MISO_PIN + #endif + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + +#endif // HAS_WIRED_LCD + +#if HAS_TMC_UART + /** + * TMC2208/TMC2209 stepper drivers + * + * Hardware serial communication ports. + * If undefined software serial is used according to the pins below + */ + //#define X_HARDWARE_SERIAL Serial1 + //#define X2_HARDWARE_SERIAL Serial1 + //#define Y_HARDWARE_SERIAL Serial1 + //#define Y2_HARDWARE_SERIAL Serial1 + //#define Z_HARDWARE_SERIAL Serial1 + //#define Z2_HARDWARE_SERIAL Serial1 + //#define E0_HARDWARE_SERIAL Serial1 + //#define E1_HARDWARE_SERIAL Serial1 + //#define E2_HARDWARE_SERIAL Serial1 + //#define E3_HARDWARE_SERIAL Serial1 + //#define E4_HARDWARE_SERIAL Serial1 +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if HOTENDS < 3 && HAS_CUTTER && !PIN_EXISTS(SPINDLE_LASER_ENA) + #define SPINDLE_LASER_ENA_PIN 45 // Use E2 ENA + #define SPINDLE_LASER_PWM_PIN 12 // Hardware PWM + #define SPINDLE_DIR_PIN 47 // Use E2 DIR +#endif |