diff options
Diffstat (limited to 'Marlin/src/pins/stm32f1/pins_FLY_MINI.h')
| -rw-r--r-- | Marlin/src/pins/stm32f1/pins_FLY_MINI.h | 176 |
1 files changed, 176 insertions, 0 deletions
diff --git a/Marlin/src/pins/stm32f1/pins_FLY_MINI.h b/Marlin/src/pins/stm32f1/pins_FLY_MINI.h new file mode 100644 index 0000000..2278d55 --- /dev/null +++ b/Marlin/src/pins/stm32f1/pins_FLY_MINI.h @@ -0,0 +1,176 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +#if NOT_TARGET(__STM32F1__) + #error "Oops! Select an STM32F1 board in 'Tools > Board.'" +#endif + +#define BOARD_INFO_NAME "FLY_MINI" +#define BOARD_WEBSITE_URL "github.com/FLYmaker" +#define DISABLE_JTAG + +// +// Flash EEPROM Emulation +// +#define FLASH_EEPROM_EMULATION +#define EEPROM_PAGE_SIZE 0x800 // 2KB +#define EEPROM_START_ADDRESS (0x8000000 + 256 * 1024 - 2 * EEPROM_PAGE_SIZE) // 256K firmware space +#define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE + +// +// Servos +// +#define SERVO0_PIN PA8 + +// +// Limit Switches +// +#define X_MIN_PIN PC12 +#define X_MAX_PIN PC11 +#define Y_MIN_PIN PC10 +#define Y_MAX_PIN PA15 +#define Z_MIN_PIN PA14 +#define Z_MAX_PIN PA13 + +// +// Steppers +// +#define X_STEP_PIN PB1 +#define X_DIR_PIN PB2 +#define X_ENABLE_PIN PB10 +#ifndef X_CS_PIN + #define X_CS_PIN PB0 +#endif + +#define Y_STEP_PIN PA2 +#define Y_DIR_PIN PC4 +#define Y_ENABLE_PIN PC5 +#ifndef Y_CS_PIN + #define Y_CS_PIN PA7 +#endif + +#define Z_STEP_PIN PA3 +#define Z_DIR_PIN PA5 +#define Z_ENABLE_PIN PA6 +#ifndef Z_CS_PIN + #define Z_CS_PIN PA4 +#endif + +#define E0_STEP_PIN PA1 +#define E0_DIR_PIN PC3 +#define E0_ENABLE_PIN PA0 +#ifndef E0_CS_PIN + #define E0_CS_PIN PC2 +#endif + +#if ENABLED(TMC_USE_SW_SPI) + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI PB15 + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO PB14 + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK PB13 + #endif +#endif + +#if HAS_TMC_UART + // + // Software serial + // + #define X_SERIAL_TX_PIN PB0 + #define X_SERIAL_RX_PIN PB0 + #define Y_SERIAL_TX_PIN PA7 + #define Y_SERIAL_RX_PIN PA7 + #define Z_SERIAL_TX_PIN PA4 + #define Z_SERIAL_RX_PIN PA4 + #define E0_SERIAL_TX_PIN PC2 + #define E0_SERIAL_RX_PIN PC2 +#endif + +// +// Heaters / Fans +// +#define HEATER_0_PIN PC6 +#define HEATER_BED_PIN PC7 +#ifndef FAN_PIN + #define FAN_PIN PC8 +#endif +#define FAN1_PIN PC9 + +// +// Temperature Sensors +// +#define TEMP_BED_PIN PC0 // Analog Input +#define TEMP_0_PIN PC1 // Analog Input + +// +// LCD Pins +// + +// +// LCD / Controller +// +#define SPI_DEVICE 2 +#define SD_SS_PIN PB12 +#define SD_SCK_PIN PB13 +#define SD_MISO_PIN PB14 +#define SD_MOSI_PIN PB15 + +#define SDSS SD_SS_PIN +#define SD_DETECT_PIN PB11 + +#define BEEPER_PIN PC14 + +#define LCD_PINS_RS PB8 +#define LCD_PINS_ENABLE PB9 +#define LCD_PINS_D4 PB7 +#define LCD_PINS_D5 PB6 +#define LCD_PINS_D6 PB5 +#define LCD_PINS_D7 PB4 + +#define BTN_EN1 PD2 +#define BTN_EN2 PB3 +#define BTN_ENC PC13 + +#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder +#endif + +// +// Filament runout +// + +// +// ST7920 Delays +// +#ifndef ST7920_DELAY_1 + #define ST7920_DELAY_1 DELAY_NS(96) +#endif +#ifndef ST7920_DELAY_2 + #define ST7920_DELAY_2 DELAY_NS(48) +#endif +#ifndef ST7920_DELAY_3 + #define ST7920_DELAY_3 DELAY_NS(715) +#endif |