Initial commit

1 files changed, 781 insertions, 0 deletions

diff --git a/Marlin/src/pins/ramps/pins_RAMPS.h b/Marlin/src/pins/ramps/pins_RAMPS.h
new file mode 100644
index 0000000..5bcd877
--- /dev/null
+++ b/Marlin/src/pins/ramps/pins_RAMPS.h
@@ -0,0 +1,781 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+/**
+ * Arduino Mega with RAMPS v1.4 (or v1.3) pin assignments
+ *
+ * Applies to the following boards:
+ *
+ *  RAMPS_14_EFB (Hotend, Fan, Bed)
+ *  RAMPS_14_EEB (Hotend0, Hotend1, Bed)
+ *  RAMPS_14_EFF (Hotend, Fan0, Fan1)
+ *  RAMPS_14_EEF (Hotend0, Hotend1, Fan)
+ *  RAMPS_14_SF  (Spindle, Controller Fan)
+ *
+ *  RAMPS_13_EFB (Hotend, Fan, Bed)
+ *  RAMPS_13_EEB (Hotend0, Hotend1, Bed)
+ *  RAMPS_13_EFF (Hotend, Fan0, Fan1)
+ *  RAMPS_13_EEF (Hotend0, Hotend1, Fan)
+ *  RAMPS_13_SF  (Spindle, Controller Fan)
+ *
+ *  Other pins_MYBOARD.h files may override these defaults
+ *
+ *  Differences between
+ *  RAMPS_13 | RAMPS_14
+ *         7 | 11
+ */
+
+#ifdef TARGET_LPC1768
+  #error "Oops! Set MOTHERBOARD to an LPC1768-based board when building for LPC1768."
+#elif defined(__STM32F1__)
+  #error "Oops! Set MOTHERBOARD to an STM32F1-based board when building for STM32F1."
+#endif
+
+#if NOT_TARGET(IS_RAMPS_SMART, IS_RAMPS_DUO, IS_RAMPS4DUE, TARGET_LPC1768, __AVR_ATmega1280__, __AVR_ATmega2560__)
+  #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' (or other appropriate target) in 'Tools > Board.'"
+#endif
+
+// Custom flags and defines for the build
+//#define BOARD_CUSTOM_BUILD_FLAGS -D__FOO__
+
+#ifndef BOARD_INFO_NAME
+  #define BOARD_INFO_NAME "RAMPS 1.4"
+#endif
+
+//
+// Servos
+//
+#ifndef SERVO0_PIN
+  #ifdef IS_RAMPS_13
+    #define SERVO0_PIN                         7
+  #else
+    #define SERVO0_PIN                        11
+  #endif
+#endif
+#ifndef SERVO1_PIN
+  #define SERVO1_PIN                           6
+#endif
+#ifndef SERVO2_PIN
+  #define SERVO2_PIN                           5
+#endif
+#ifndef SERVO3_PIN
+  #define SERVO3_PIN                           4
+#endif
+
+//
+// Limit Switches
+//
+#ifndef X_STOP_PIN
+  #ifndef X_MIN_PIN
+    #define X_MIN_PIN                          3
+  #endif
+  #ifndef X_MAX_PIN
+    #define X_MAX_PIN                          2
+  #endif
+#endif
+#ifndef Y_STOP_PIN
+  #ifndef Y_MIN_PIN
+    #define Y_MIN_PIN                         14
+  #endif
+  #ifndef Y_MAX_PIN
+    #define Y_MAX_PIN                         15
+  #endif
+#endif
+#ifndef Z_STOP_PIN
+  #ifndef Z_MIN_PIN
+    #define Z_MIN_PIN                         18
+  #endif
+  #ifndef Z_MAX_PIN
+    #define Z_MAX_PIN                         19
+  #endif
+#endif
+
+//
+// Z Probe (when not Z_MIN_PIN)
+//
+#ifndef Z_MIN_PROBE_PIN
+  #define Z_MIN_PROBE_PIN                     32
+#endif
+
+//
+// Steppers
+//
+#define X_STEP_PIN                            54
+#define X_DIR_PIN                             55
+#define X_ENABLE_PIN                          38
+#ifndef X_CS_PIN
+  #define X_CS_PIN                            53
+#endif
+
+#define Y_STEP_PIN                            60
+#define Y_DIR_PIN                             61
+#define Y_ENABLE_PIN                          56
+#ifndef Y_CS_PIN
+  #define Y_CS_PIN                            49
+#endif
+
+#ifndef Z_STEP_PIN
+  #define Z_STEP_PIN                          46
+#endif
+#define Z_DIR_PIN                             48
+#define Z_ENABLE_PIN                          62
+#ifndef Z_CS_PIN
+  #define Z_CS_PIN                            40
+#endif
+
+#define E0_STEP_PIN                           26
+#define E0_DIR_PIN                            28
+#define E0_ENABLE_PIN                         24
+#ifndef E0_CS_PIN
+  #define E0_CS_PIN                           42
+#endif
+
+#define E1_STEP_PIN                           36
+#define E1_DIR_PIN                            34
+#define E1_ENABLE_PIN                         30
+#ifndef E1_CS_PIN
+  #define E1_CS_PIN                           44
+#endif
+
+//
+// Temperature Sensors
+//
+#ifndef TEMP_0_PIN
+  #define TEMP_0_PIN                          13  // Analog Input
+#endif
+#ifndef TEMP_1_PIN
+  #define TEMP_1_PIN                          15  // Analog Input
+#endif
+#ifndef TEMP_BED_PIN
+  #define TEMP_BED_PIN                        14  // Analog Input
+#endif
+
+//
+// SPI for Max6675 or Max31855 Thermocouple
+//
+#ifndef MAX6675_SS_PIN
+  #define MAX6675_SS_PIN                      66  // Don't use 53 if using Display/SD card (SDSS) or 49 (SD_DETECT_PIN)
+#endif
+
+//
+// Augmentation for auto-assigning RAMPS plugs
+//
+#if NONE(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D)
+  #if HAS_MULTI_HOTEND
+    #if TEMP_SENSOR_BED
+      #define IS_RAMPS_EEB
+    #else
+      #define IS_RAMPS_EEF
+    #endif
+  #elif TEMP_SENSOR_BED
+    #define IS_RAMPS_EFB
+  #else
+    #define IS_RAMPS_EFF
+  #endif
+#endif
+
+//
+// Heaters / Fans
+//
+#ifndef MOSFET_D_PIN
+  #define MOSFET_D_PIN                        -1
+#endif
+#ifndef RAMPS_D8_PIN
+  #define RAMPS_D8_PIN                         8
+#endif
+#ifndef RAMPS_D9_PIN
+  #define RAMPS_D9_PIN                         9
+#endif
+#ifndef RAMPS_D10_PIN
+  #define RAMPS_D10_PIN                       10
+#endif
+
+#define HEATER_0_PIN               RAMPS_D10_PIN
+
+#if ENABLED(IS_RAMPS_EFB)                         // Hotend, Fan, Bed
+  #define HEATER_BED_PIN            RAMPS_D8_PIN
+#elif ENABLED(IS_RAMPS_EEF)                       // Hotend, Hotend, Fan
+  #define HEATER_1_PIN              RAMPS_D9_PIN
+#elif ENABLED(IS_RAMPS_EEB)                       // Hotend, Hotend, Bed
+  #define HEATER_1_PIN              RAMPS_D9_PIN
+  #define HEATER_BED_PIN            RAMPS_D8_PIN
+#elif ENABLED(IS_RAMPS_EFF)                       // Hotend, Fan, Fan
+  #define FAN1_PIN                  RAMPS_D8_PIN
+#elif DISABLED(IS_RAMPS_SF)                       // Not Spindle, Fan (i.e., "EFBF" or "EFBE")
+  #define HEATER_BED_PIN            RAMPS_D8_PIN
+  #if HOTENDS == 1
+    #define FAN1_PIN                MOSFET_D_PIN
+  #else
+    #define HEATER_1_PIN            MOSFET_D_PIN
+  #endif
+#endif
+
+#ifndef FAN_PIN
+  #if EITHER(IS_RAMPS_EFB, IS_RAMPS_EFF)          // Hotend, Fan, Bed or Hotend, Fan, Fan
+    #define FAN_PIN                 RAMPS_D9_PIN
+  #elif EITHER(IS_RAMPS_EEF, IS_RAMPS_SF)         // Hotend, Hotend, Fan or Spindle, Fan
+    #define FAN_PIN                 RAMPS_D8_PIN
+  #elif ENABLED(IS_RAMPS_EEB)                     // Hotend, Hotend, Bed
+    #define FAN_PIN                            4  // IO pin. Buffer needed
+  #else                                           // Non-specific are "EFB" (i.e., "EFBF" or "EFBE")
+    #define FAN_PIN                 RAMPS_D9_PIN
+  #endif
+#endif
+
+//
+// Misc. Functions
+//
+#define SDSS                                  53
+#define LED_PIN                               13
+
+#ifndef FILWIDTH_PIN
+  #define FILWIDTH_PIN                         5  // Analog Input on AUX2
+#endif
+
+// RAMPS 1.4 DIO 4 on the servos connector
+#ifndef FIL_RUNOUT_PIN
+  #define FIL_RUNOUT_PIN                       4
+#endif
+
+#ifndef PS_ON_PIN
+  #define PS_ON_PIN                           12
+#endif
+
+#if ENABLED(CASE_LIGHT_ENABLE) && !defined(CASE_LIGHT_PIN) && !defined(SPINDLE_LASER_ENA_PIN)
+  #if NUM_SERVOS <= 1                             // Prefer the servo connector
+    #define CASE_LIGHT_PIN                     6  // Hardware PWM
+  #elif HAS_FREE_AUX2_PINS
+    #define CASE_LIGHT_PIN                    44  // Hardware PWM
+  #endif
+#endif
+
+//
+// M3/M4/M5 - Spindle/Laser Control
+//
+#if HAS_CUTTER && !defined(SPINDLE_LASER_ENA_PIN)
+  #if !NUM_SERVOS                                 // Use servo connector if possible
+    #define SPINDLE_LASER_ENA_PIN              4  // Pullup or pulldown!
+    #define SPINDLE_LASER_PWM_PIN              6  // Hardware PWM
+    #define SPINDLE_DIR_PIN                    5
+  #elif HAS_FREE_AUX2_PINS
+    #define SPINDLE_LASER_ENA_PIN             40  // Pullup or pulldown!
+    #define SPINDLE_LASER_PWM_PIN             44  // Hardware PWM
+    #define SPINDLE_DIR_PIN                   65
+  #else
+    #error "No auto-assignable Spindle/Laser pins available."
+  #endif
+#endif
+
+//
+// TMC software SPI
+//
+#if ENABLED(TMC_USE_SW_SPI)
+  #ifndef TMC_SW_MOSI
+    #define TMC_SW_MOSI                       66
+  #endif
+  #ifndef TMC_SW_MISO
+    #define TMC_SW_MISO                       44
+  #endif
+  #ifndef TMC_SW_SCK
+    #define TMC_SW_SCK                        64
+  #endif
+#endif
+
+#if HAS_TMC_UART
+  /**
+   * TMC2208/TMC2209 stepper drivers
+   *
+   * Hardware serial communication ports.
+   * If undefined software serial is used according to the pins below
+   */
+  //#define X_HARDWARE_SERIAL Serial1
+  //#define X2_HARDWARE_SERIAL Serial1
+  //#define Y_HARDWARE_SERIAL Serial1
+  //#define Y2_HARDWARE_SERIAL Serial1
+  //#define Z_HARDWARE_SERIAL Serial1
+  //#define Z2_HARDWARE_SERIAL Serial1
+  //#define E0_HARDWARE_SERIAL Serial1
+  //#define E1_HARDWARE_SERIAL Serial1
+  //#define E2_HARDWARE_SERIAL Serial1
+  //#define E3_HARDWARE_SERIAL Serial1
+  //#define E4_HARDWARE_SERIAL Serial1
+
+  //
+  // Software serial
+  //
+
+  #ifndef X_SERIAL_TX_PIN
+    #define X_SERIAL_TX_PIN                   40
+  #endif
+  #ifndef X_SERIAL_RX_PIN
+    #define X_SERIAL_RX_PIN                   63
+  #endif
+  #ifndef X2_SERIAL_TX_PIN
+    #define X2_SERIAL_TX_PIN                  -1
+  #endif
+  #ifndef X2_SERIAL_RX_PIN
+    #define X2_SERIAL_RX_PIN                  -1
+  #endif
+
+  #ifndef Y_SERIAL_TX_PIN
+    #define Y_SERIAL_TX_PIN                   59
+  #endif
+  #ifndef Y_SERIAL_RX_PIN
+    #define Y_SERIAL_RX_PIN                   64
+  #endif
+  #ifndef Y2_SERIAL_TX_PIN
+    #define Y2_SERIAL_TX_PIN                  -1
+  #endif
+  #ifndef Y2_SERIAL_RX_PIN
+    #define Y2_SERIAL_RX_PIN                  -1
+  #endif
+
+  #ifndef Z_SERIAL_TX_PIN
+    #define Z_SERIAL_TX_PIN                   42
+  #endif
+  #ifndef Z_SERIAL_RX_PIN
+    #define Z_SERIAL_RX_PIN                   65
+  #endif
+  #ifndef Z2_SERIAL_TX_PIN
+    #define Z2_SERIAL_TX_PIN                  -1
+  #endif
+  #ifndef Z2_SERIAL_RX_PIN
+    #define Z2_SERIAL_RX_PIN                  -1
+  #endif
+
+  #ifndef E0_SERIAL_TX_PIN
+    #define E0_SERIAL_TX_PIN                  44
+  #endif
+  #ifndef E0_SERIAL_RX_PIN
+    #define E0_SERIAL_RX_PIN                  66
+  #endif
+  #ifndef E1_SERIAL_TX_PIN
+    #define E1_SERIAL_TX_PIN                  -1
+  #endif
+  #ifndef E1_SERIAL_RX_PIN
+    #define E1_SERIAL_RX_PIN                  -1
+  #endif
+  #ifndef E2_SERIAL_TX_PIN
+    #define E2_SERIAL_TX_PIN                  -1
+  #endif
+  #ifndef E2_SERIAL_RX_PIN
+    #define E2_SERIAL_RX_PIN                  -1
+  #endif
+  #ifndef E3_SERIAL_TX_PIN
+    #define E3_SERIAL_TX_PIN                  -1
+  #endif
+  #ifndef E3_SERIAL_RX_PIN
+    #define E3_SERIAL_RX_PIN                  -1
+  #endif
+  #ifndef E4_SERIAL_TX_PIN
+    #define E4_SERIAL_TX_PIN                  -1
+  #endif
+  #ifndef E4_SERIAL_RX_PIN
+    #define E4_SERIAL_RX_PIN                  -1
+  #endif
+  #ifndef E5_SERIAL_TX_PIN
+    #define E5_SERIAL_TX_PIN                  -1
+  #endif
+  #ifndef E5_SERIAL_RX_PIN
+    #define E5_SERIAL_RX_PIN                  -1
+  #endif
+  #ifndef E6_SERIAL_TX_PIN
+    #define E6_SERIAL_TX_PIN                  -1
+  #endif
+  #ifndef E6_SERIAL_RX_PIN
+    #define E6_SERIAL_RX_PIN                  -1
+  #endif
+  #ifndef E7_SERIAL_TX_PIN
+    #define E7_SERIAL_TX_PIN                  -1
+  #endif
+  #ifndef E7_SERIAL_RX_PIN
+    #define E7_SERIAL_RX_PIN                  -1
+  #endif
+#endif
+
+//
+// Průša i3 MK2 Multiplexer Support
+//
+#ifndef E_MUX0_PIN
+  #define E_MUX0_PIN                          40  // Z_CS_PIN
+#endif
+#ifndef E_MUX1_PIN
+  #define E_MUX1_PIN                          42  // E0_CS_PIN
+#endif
+#ifndef E_MUX2_PIN
+  #define E_MUX2_PIN                          44  // E1_CS_PIN
+#endif
+
+//////////////////////////
+// LCDs and Controllers //
+//////////////////////////
+
+#if HAS_WIRED_LCD
+
+  //
+  // LCD Display output pins
+  //
+  #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
+
+    #define LCD_PINS_RS                       49  // CS chip select /SS chip slave select
+    #define LCD_PINS_ENABLE                   51  // SID (MOSI)
+    #define LCD_PINS_D4                       52  // SCK (CLK) clock
+
+  #elif BOTH(IS_NEWPANEL, PANEL_ONE)
+
+    #define LCD_PINS_RS                       40
+    #define LCD_PINS_ENABLE                   42
+    #define LCD_PINS_D4                       65
+    #define LCD_PINS_D5                       66
+    #define LCD_PINS_D6                       44
+    #define LCD_PINS_D7                       64
+
+  #elif ENABLED(TFTGLCD_PANEL_SPI)
+
+    #define TFTGLCD_CS                        33
+
+  #else
+
+    #if ENABLED(CR10_STOCKDISPLAY)
+
+      #define LCD_PINS_RS                     27
+      #define LCD_PINS_ENABLE                 29
+      #define LCD_PINS_D4                     25
+
+      #if !IS_NEWPANEL
+        #define BEEPER_PIN                    37
+      #endif
+
+    #elif ENABLED(ZONESTAR_LCD)
+
+      #error "CAUTION! ZONESTAR_LCD on RAMPS requires wiring modifications. It plugs into AUX2 but GND and 5V need to be swapped. Comment out this line to continue."
+      #define LCD_PINS_RS                     64
+      #define LCD_PINS_ENABLE                 44
+      #define LCD_PINS_D4                     63
+      #define LCD_PINS_D5                     40
+      #define LCD_PINS_D6                     42
+      #define LCD_PINS_D7                     65
+
+    #else
+
+      #if EITHER(MKS_12864OLED, MKS_12864OLED_SSD1306)
+        #define LCD_PINS_DC                   25  // Set as output on init
+        #define LCD_PINS_RS                   27  // Pull low for 1s to init
+        // DOGM SPI LCD Support
+        #define DOGLCD_A0            LCD_PINS_DC
+        #define DOGLCD_CS                     16
+        #define DOGLCD_MOSI                   17
+        #define DOGLCD_SCK                    23
+      #else
+        #define LCD_PINS_RS                   16
+        #define LCD_PINS_ENABLE               17
+        #define LCD_PINS_D4                   23
+        #define LCD_PINS_D5                   25
+        #define LCD_PINS_D6                   27
+      #endif
+
+      #define LCD_PINS_D7                     29
+
+      #if !IS_NEWPANEL
+        #define BEEPER_PIN                    33
+      #endif
+
+    #endif
+
+    #if !IS_NEWPANEL
+      // Buttons attached to a shift register
+      // Not wired yet
+      //#define SHIFT_CLK_PIN                 38
+      //#define SHIFT_LD_PIN                  42
+      //#define SHIFT_OUT_PIN                 40
+      //#define SHIFT_EN_PIN                  17
+    #endif
+
+  #endif
+
+  #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
+    #define BTN_ENC_EN               LCD_PINS_D7  // Detect the presence of the encoder
+  #endif
+
+  //
+  // LCD Display input pins
+  //
+  #if IS_NEWPANEL
+
+    #if IS_RRD_SC
+
+      #define BEEPER_PIN                      37
+
+      #if ENABLED(CR10_STOCKDISPLAY)
+        #define BTN_EN1                       17
+        #define BTN_EN2                       23
+      #else
+        #define BTN_EN1                       31
+        #define BTN_EN2                       33
+      #endif
+
+      #define BTN_ENC                         35
+      #ifndef SD_DETECT_PIN
+        #define SD_DETECT_PIN                 49
+      #endif
+      #ifndef KILL_PIN
+        #define KILL_PIN                      41
+      #endif
+
+      #if ENABLED(BQ_LCD_SMART_CONTROLLER)
+        #define LCD_BACKLIGHT_PIN             39
+      #endif
+
+    #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
+
+      #define BTN_EN1                         64
+      #define BTN_EN2                         59
+      #define BTN_ENC                         63
+      #define SD_DETECT_PIN                   42
+
+    #elif ENABLED(LCD_I2C_PANELOLU2)
+
+      #define BTN_EN1                         47
+      #define BTN_EN2                         43
+      #define BTN_ENC                         32
+      #define LCD_SDSS                      SDSS
+      #define KILL_PIN                        41
+
+    #elif ENABLED(LCD_I2C_VIKI)
+
+      #define BTN_EN1                         40  // https://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
+      #define BTN_EN2                         42
+      #define BTN_ENC                         -1
+
+      #define LCD_SDSS                      SDSS
+      #define SD_DETECT_PIN                   49
+
+    #elif ANY(VIKI2, miniVIKI)
+
+      #define DOGLCD_CS                       45
+      #define DOGLCD_A0                       44
+      #define LCD_SCREEN_ROT_180
+
+      #define BEEPER_PIN                      33
+      #define STAT_LED_RED_PIN                32
+      #define STAT_LED_BLUE_PIN               35
+
+      #define BTN_EN1                         22
+      #define BTN_EN2                          7
+      #define BTN_ENC                         39
+
+      #define SD_DETECT_PIN                   -1  // Pin 49 for display SD interface, 72 for easy adapter board
+      #define KILL_PIN                        31
+
+    #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
+
+      #define DOGLCD_CS                       29
+      #define DOGLCD_A0                       27
+
+      #define BEEPER_PIN                      23
+      #define LCD_BACKLIGHT_PIN               33
+
+      #define BTN_EN1                         35
+      #define BTN_EN2                         37
+      #define BTN_ENC                         31
+
+      #define LCD_SDSS                      SDSS
+      #define SD_DETECT_PIN                   49
+      #define KILL_PIN                        41
+
+    #elif EITHER(MKS_MINI_12864, FYSETC_MINI_12864)
+
+      #define BEEPER_PIN                      37
+      #define BTN_ENC                         35
+      #define SD_DETECT_PIN                   49
+
+      #ifndef KILL_PIN
+        #define KILL_PIN                      41
+      #endif
+
+      #if ENABLED(MKS_MINI_12864)
+
+        #define DOGLCD_A0                     27
+        #define DOGLCD_CS                     25
+
+        // GLCD features
+        // Uncomment screen orientation
+        //#define LCD_SCREEN_ROT_90
+        //#define LCD_SCREEN_ROT_180
+        //#define LCD_SCREEN_ROT_270
+
+        // not connected to a pin
+        #define LCD_BACKLIGHT_PIN             -1  // 65 (MKS mini12864 can't adjust backlight by software!)
+
+        #define BTN_EN1                       31
+        #define BTN_EN2                       33
+
+      #elif ENABLED(FYSETC_MINI_12864)
+
+        // From https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8
+
+        #define DOGLCD_A0                     16
+        #define DOGLCD_CS                     17
+
+        #define BTN_EN1                       33
+        #define BTN_EN2                       31
+
+        //#define FORCE_SOFT_SPI                  // Use this if default of hardware SPI causes display problems
+                                                  //   results in LCD soft SPI mode 3, SD soft SPI mode 0
+
+        #define LCD_RESET_PIN                 23  // Must be high or open for LCD to operate normally.
+
+        #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
+          #ifndef RGB_LED_R_PIN
+            #define RGB_LED_R_PIN             25
+          #endif
+          #ifndef RGB_LED_G_PIN
+            #define RGB_LED_G_PIN             27
+          #endif
+          #ifndef RGB_LED_B_PIN
+            #define RGB_LED_B_PIN             29
+          #endif
+        #elif ENABLED(FYSETC_MINI_12864_2_1)
+          #define NEOPIXEL_PIN                25
+        #endif
+
+      #endif
+
+    #elif ENABLED(MINIPANEL)
+
+      #define BEEPER_PIN                      42
+      // not connected to a pin
+      #define LCD_BACKLIGHT_PIN               65  // backlight LED on A11/D65
+
+      #define DOGLCD_A0                       44
+      #define DOGLCD_CS                       66
+
+      // GLCD features
+      // Uncomment screen orientation
+      //#define LCD_SCREEN_ROT_90
+      //#define LCD_SCREEN_ROT_180
+      //#define LCD_SCREEN_ROT_270
+
+      #define BTN_EN1                         40
+      #define BTN_EN2                         63
+      #define BTN_ENC                         59
+
+      #define SD_DETECT_PIN                   49
+      #define KILL_PIN                        64
+
+    #elif ENABLED(ZONESTAR_LCD)
+
+      #define ADC_KEYPAD_PIN                  12
+
+    #elif ENABLED(AZSMZ_12864)
+
+      // Pins only defined for RAMPS_SMART currently
+      #error "No pins defined for RAMPS with AZSMZ_12864."
+
+    #elif IS_TFTGLCD_PANEL
+
+      #define SD_DETECT_PIN                   49
+
+    #else
+
+      // Beeper on AUX-4
+      #define BEEPER_PIN                      33
+
+      // Buttons are directly attached to AUX-2
+      #if ENABLED(PANEL_ONE)
+        #define BTN_EN1                       59  // AUX2 PIN 3
+        #define BTN_EN2                       63  // AUX2 PIN 4
+        #define BTN_ENC                       49  // AUX3 PIN 7
+      #else
+        #define BTN_EN1                       37
+        #define BTN_EN2                       35
+        #define BTN_ENC                       31
+      #endif
+
+      #if ENABLED(G3D_PANEL)
+        #define SD_DETECT_PIN                 49
+        #define KILL_PIN                      41
+      #endif
+
+    #endif
+  #endif // IS_NEWPANEL
+
+#endif // HAS_WIRED_LCD
+
+#if IS_RRW_KEYPAD && !HAS_ADC_BUTTONS
+  #define SHIFT_OUT_PIN                       40
+  #define SHIFT_CLK_PIN                       44
+  #define SHIFT_LD_PIN                        42
+  #ifndef BTN_EN1
+    #define BTN_EN1                           64
+  #endif
+  #ifndef BTN_EN2
+    #define BTN_EN2                           59
+  #endif
+  #ifndef BTN_ENC
+    #define BTN_ENC                           63
+  #endif
+#endif
+
+#if BOTH(TOUCH_UI_FTDI_EVE, LCD_FYSETC_TFT81050)
+
+  #error "CAUTION! LCD_FYSETC_TFT81050 requires wiring modifications. See 'pins_RAMPS.h' for details. Comment out this line to continue."
+
+  /** FYSETC TFT TFT81050 display pinout
+   *
+   *               Board                                     Display
+   *               _____                                     _____
+   *  (SCK)   D52 | 1 2 | D50    (MISO)                MISO | 1 2 | SCK
+   *  (SD_CS) D53 | 3 4 | D33 (BNT_EN2) (BNT_EN2) MOD_RESET | 3 4 | SD_CS
+   *  (MOSI)  D51 | 5 6   D31 (BNT_EN1) (BNT_EN1)    LCD_CS | 5 6   MOSI
+   *        RESET | 7 8 | D49  (SD_DET)              SD_DET | 7 8 | RESET
+   *           NC | 9 10| GND                           GND | 9 10| 5V
+   *               -----                                     -----
+   *                EXP2                                      EXP1
+   *
+   * Needs custom cable:
+   *
+   *    Board   Adapter   Display
+   *           _________
+   *   EXP2-1 ----------- EXP1-10
+   *   EXP2-2 ----------- EXP1-9
+   *   EXP2-4 ----------- EXP1-8
+   *   EXP2-4 ----------- EXP1-7
+   *   EXP2-3 ----------- EXP1-6
+   *   EXP2-6 ----------- EXP1-5
+   *   EXP2-7 ----------- EXP1-4
+   *   EXP2-8 ----------- EXP1-3
+   *   EXP2-1 ----------- EXP1-2
+   *  EXP1-10 ----------- EXP1-1
+   *
+   *  NOTE: The MISO pin should not get a 5V signal.
+   *        To fix, insert a 1N4148 diode in the MISO line.
+   */
+
+  #define BEEPER_PIN                          37
+
+  #define SD_DETECT_PIN                       49
+
+  #define CLCD_MOD_RESET                      31
+  #define CLCD_SPI_CS                         33
+#endif // TOUCH_UI_FTDI_EVE && LCD_FYSETC_TFT81050