Initial commit

1 files changed, 318 insertions, 0 deletions

diff --git a/Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h b/Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h
new file mode 100644
index 0000000..c49c31e
--- /dev/null
+++ b/Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h
@@ -0,0 +1,318 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+/**
+ * FLSUN HiSpeed V1 (STM32F103VET6) board pin assignments
+ * FLSun Hispeed (clone MKS_Robin_miniV2) board.
+ *
+ * MKS Robin Mini USB uses UART3 (PB10-TX, PB11-RX)
+ * #define SERIAL_PORT_2 3
+ */
+
+#if NOT_TARGET(__STM32F1__, STM32F1xx)
+  #error "Oops! Select an STM32F1 board in 'Tools > Board.'"
+#elif HOTENDS > 1 || E_STEPPERS > 1
+  #error "FLSUN HiSpeedV1 only supports one hotend / E-stepper. Comment out this line to continue."
+#endif
+
+#define BOARD_INFO_NAME      "FLSun HiSpeedV1"
+#define BOARD_WEBSITE_URL    "github.com/Foxies-CSTL"
+
+#define BOARD_NO_NATIVE_USB
+
+// Avoid conflict with TIMER_SERVO when using the STM32 HAL
+#define TEMP_TIMER 5
+
+//
+// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role
+//
+#define DISABLE_DEBUG
+
+//
+// EEPROM
+//
+#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
+  #define FLASH_EEPROM_EMULATION
+  #define EEPROM_PAGE_SIZE     (0x800U)           // 2KB
+  #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL)
+  #define MARLIN_EEPROM_SIZE    EEPROM_PAGE_SIZE  // 2KB
+#endif
+
+//
+// SPI
+// Note: FLSun Hispeed (clone MKS_Robin_miniV2) board is using SPI2 interface.
+//
+#define SD_SCK_PIN                          PB13  // SPI2
+#define SD_MISO_PIN                         PB14  // SPI2
+#define SD_MOSI_PIN                         PB15  // SPI2
+#define SPI_DEVICE 2
+
+// SPI Flash
+#define HAS_SPI_FLASH                          1
+#define SPI_FLASH_SIZE                 0x1000000  // 16MB
+
+#if HAS_SPI_FLASH
+  // SPI 2
+  #define W25QXX_CS_PIN                     PB12  // SPI2_NSS / Flash chip-select
+  #define W25QXX_MOSI_PIN                   PB15
+  #define W25QXX_MISO_PIN                   PB14
+  #define W25QXX_SCK_PIN                    PB13
+#endif
+
+//
+// Servos
+//
+//#define SERVO0_PIN                        PA8   // use IO0 to enable BLTOUCH support/remove Mks_Wifi
+
+//
+// Limit Switches
+//
+#define X_STOP_PIN                          PA15  // -X
+#define Y_STOP_PIN                          PA12  // -Y
+#define Z_MIN_PIN                           PA11  // -Z
+#define Z_MAX_PIN                           PC4   // +Z
+
+#ifndef FIL_RUNOUT_PIN
+  #define FIL_RUNOUT_PIN            MT_DET_1_PIN
+#endif
+
+//
+// Steppers
+//
+#define X_ENABLE_PIN                        PE4   // X_EN
+#define X_STEP_PIN                          PE3   // X_STEP
+#define X_DIR_PIN                           PE2   // X_DIR
+
+#define Y_ENABLE_PIN                        PE1   // Y_EN
+#define Y_STEP_PIN                          PE0   // Y_STEP
+#define Y_DIR_PIN                           PB9   // Y_DIR
+
+#define Z_ENABLE_PIN                        PB8   // Z_EN
+#define Z_STEP_PIN                          PB5   // Z_STEP
+#define Z_DIR_PIN                           PB4   // Z_DIR
+
+#define E0_ENABLE_PIN                       PB3   // E0_EN
+#define E0_STEP_PIN                         PD6   // E0_STEP
+#define E0_DIR_PIN                          PD3   // E0_DIR
+
+/**
+ * FLSUN Hi-Speed has no hard-wired UART pins for TMC drivers.
+ * Several wiring options are provided below, defaulting to
+ * to the most compatible.
+ */
+#if HAS_TMC_UART
+  // SoftwareSerial with one pin per driver
+  // Compatible with TMC2208 and TMC2209 drivers
+  #define X_SERIAL_TX_PIN                   PA10  // RXD1
+  #define X_SERIAL_RX_PIN                   PA10  // RXD1
+  #define Y_SERIAL_TX_PIN                   PA9   // TXD1
+  #define Y_SERIAL_RX_PIN                   PA9   // TXD1
+  #define Z_SERIAL_TX_PIN                   PC7   // IO1
+  #define Z_SERIAL_RX_PIN                   PC7   // IO1
+  #define TMC_BAUD_RATE                    19200
+#else
+  // Motor current PWM pins
+  #define MOTOR_CURRENT_PWM_XY_PIN          PA6   // VREF2/3 CONTROL XY
+  #define MOTOR_CURRENT_PWM_Z_PIN           PA7   // VREF4 CONTROL Z
+  #define MOTOR_CURRENT_PWM_RANGE           1500  // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp
+  #ifndef DEFAULT_PWM_MOTOR_CURRENT
+    #define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 }
+  #endif
+
+  /**
+   * MKS Robin_Wifi or another ESP8266 module
+   *
+   *      __ESP(M1)__       -J1-
+   *  GND| 15 | | 08 |+3v3  (22)  RXD1      (PA10)
+   *     | 16 | | 07 |MOSI  (21)  TXD1      (PA9)   Active LOW, probably OK to leave floating
+   *  IO2| 17 | | 06 |MISO  (19)  IO1       (PC7)   Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
+   *  IO0| 18 | | 05 |CLK   (18)  IO0       (PA8)   Must be HIGH (ESP3D software configures this with a pullup so OK to leave as floating)
+   *  IO1| 19 | | 03 |EN    (03)  WIFI_EN           Must be HIGH for module to run
+   *     | nc | | nc |      (01)  WIFI_CTRL (PA5)
+   *   RX| 21 | | nc |
+   *   TX| 22 | | 01 |RST
+   *       ￣￣ AE￣￣
+   */
+  // Module ESP-WIFI
+  #define ESP_WIFI_MODULE_COM                  2  // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
+  #define ESP_WIFI_MODULE_BAUDRATE      BAUDRATE  // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
+  #define ESP_WIFI_MODULE_RESET_PIN         PA5   // WIFI CTRL/RST
+  #define ESP_WIFI_MODULE_ENABLE_PIN        -1
+  #define ESP_WIFI_MODULE_TXD_PIN           PA9   // MKS or ESP WIFI RX PIN
+  #define ESP_WIFI_MODULE_RXD_PIN           PA10  // MKS or ESP WIFI TX PIN
+#endif
+
+//
+// EXTRUDER
+//
+#if AXIS_DRIVER_TYPE_E0(TMC2208) || AXIS_DRIVER_TYPE_E0(TMC2209)
+  #define E0_SERIAL_TX_PIN                  PA8   // IO0
+  #define E0_SERIAL_RX_PIN                  PA8   // IO0
+  #define TMC_BAUD_RATE                    19200
+#else
+  // Motor current PWM pins
+  #define MOTOR_CURRENT_PWM_E_PIN           PB0   // VREF1 CONTROL E
+  #define MOTOR_CURRENT_PWM_RANGE           1500  // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp
+  #ifndef DEFAULT_PWM_MOTOR_CURRENT
+   #define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 }
+  #endif
+#endif
+
+//
+// Temperature Sensors (THM)
+//
+#define TEMP_0_PIN                          PC1   // TEMP_E0
+#define TEMP_BED_PIN                        PC0   // TEMP_BED
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN                        PC3   // HEATER_E0
+#define HEATER_BED_PIN                      PA0   // HEATER_BED-WKUP
+
+#define FAN_PIN                             PB1   // E_FAN
+
+//
+// Misc. Functions
+//
+//#define POWER_LOSS_PIN                    PA1   // PW_SO
+#if ENABLED(BACKUP_POWER_SUPPLY)
+  #define POWER_LOSS_PIN                    PA2   // PW_DET (UPS) MKSPWC
+#endif
+
+/**
+ *    Connector J2
+ *      -------
+ * DIO O|1   2|O  3v3
+ * CSK O|3   5|O  GND
+ * RST O|5   6|O  GND
+ *      -------
+ */
+//#define SW_DIO                            PA13
+//#define SW_CLK                            PA14
+//#define SW_RST                            NRST  // (14)
+
+//
+// Power Supply Control
+//
+#if ENABLED(PSU_CONTROL)
+  #define KILL_PIN                          PA2   // PW_DET
+  #define KILL_PIN_INVERTING                true
+  //#define PS_ON_PIN                       PA3   // PW_CN /PW_OFF
+#endif
+
+#define MT_DET_1_PIN                        PA4   // MT_DET
+#define MT_DET_2_PIN                        PE6   // FALA_CRTL
+#define MT_DET_PIN_INVERTING               false
+
+//
+// LED / NEOPixel
+//
+//#define LED_PIN                           PB2   // BOOT1
+
+#if ENABLED(NEOPIXEL_LED)
+  #define LED_PWM                           PC7   // IO1
+  #ifndef NEOPIXEL_PIN
+    #define NEOPIXEL_PIN                 LED_PWM  // USED WIFI IO0/IO1 PIN
+  #endif
+#endif
+
+//
+// SD Card
+//
+#ifndef SDCARD_CONNECTION
+  #define SDCARD_CONNECTION              ONBOARD
+#endif
+
+// Use the on-board card socket labeled SD_Extender
+#if SD_CONNECTION_IS(CUSTOM_CABLE)
+  #define SD_SCK_PIN                        PC12
+  #define SD_MISO_PIN                       PC8
+  #define SD_MOSI_PIN                       PD2
+  #define SD_SS_PIN                         -1
+  #define SD_DETECT_PIN                     PD12  // SD_CD (if -1 no detection)
+#else
+  #define SDIO_SUPPORT
+  #define SDIO_CLOCK                     4500000  // 4.5 MHz
+  #define SDIO_READ_RETRIES                   16
+  #define ONBOARD_SPI_DEVICE                   1  // SPI1
+  #define ONBOARD_SD_CS_PIN                 PC11
+  #define SD_DETECT_PIN                     -1    // SD_CD (-1 active refresh)
+#endif
+
+//
+// LCD / Controller
+//
+#ifndef BEEPER_PIN
+  #define BEEPER_PIN                        PC5
+#endif
+
+#if ENABLED(SPEAKER) && BEEPER_PIN == PC5
+  #error "FLSun HiSpeed default BEEPER_PIN is not a SPEAKER."
+#endif
+
+#if HAS_FSMC_TFT || HAS_GRAPHICAL_TFT
+  #define TFT_CS_PIN                        PD7   // NE4
+  #define TFT_RS_PIN                        PD11  // A0
+#endif
+
+#if HAS_FSMC_TFT
+  /**
+   * Note: MKS Robin TFT screens use various TFT controllers
+   * Supported screens are based on the ILI9341, ST7789V and ILI9328 (320x240)
+   * ILI9488 is not supported
+   * Define init sequences for other screens in u8g_dev_tft_320x240_upscale_from_128x64.cpp
+   *
+   * If the screen stays white, disable 'LCD_RESET_PIN'
+   * to let the bootloader init the screen.
+   *
+   * Setting an 'LCD_RESET_PIN' may cause a flicker when entering the LCD menu
+   * because Marlin uses the reset as a failsafe to revive a glitchy LCD.
+   */
+  //#define TFT_RESET_PIN                   PC6   // FSMC_RST
+  #define TFT_BACKLIGHT_PIN                 PD13
+  #define FSMC_CS_PIN                 TFT_CS_PIN  // NE4
+  #define FSMC_RS_PIN                 TFT_RS_PIN  // A0
+
+  #define LCD_USE_DMA_FSMC                        // Use DMA transfers to send data to the TFT
+  #define FSMC_DMA_DEV                      DMA2
+  #define FSMC_DMA_CHANNEL               DMA_CH5
+  #ifdef TFT_CLASSIC_UI
+    #define TFT_MARLINBG_COLOR            0x3186  // Grey
+    #define TFT_MARLINUI_COLOR            0xC7B6  // Green
+    #define TFT_BTARROWS_COLOR            0xDEE6  // Yellow
+    #define TFT_BTOKMENU_COLOR            0x145F  // Cyan
+  #endif
+  #define TFT_BUFFER_SIZE                  14400
+#elif HAS_GRAPHICAL_TFT
+  #define TFT_RESET_PIN                     PC6
+  #define TFT_BACKLIGHT_PIN                 PD13
+#endif
+
+#if NEED_TOUCH_PINS
+  #define TOUCH_CS_PIN                      PC2   // SPI2_NSS
+  #define TOUCH_SCK_PIN                     PB13  // SPI2_SCK
+  #define TOUCH_MISO_PIN                    PB14  // SPI2_MISO
+  #define TOUCH_MOSI_PIN                    PB15  // SPI2_MOSI
+  #define TOUCH_INT_PIN                     -1
+#endif