diff options
Diffstat (limited to 'Marlin/src/pins/rambo')
| -rw-r--r-- | Marlin/src/pins/rambo/pins_EINSY_RAMBO.h | 196 | ||||
| -rw-r--r-- | Marlin/src/pins/rambo/pins_EINSY_RETRO.h | 203 | ||||
| -rw-r--r-- | Marlin/src/pins/rambo/pins_MINIRAMBO.h | 196 | ||||
| -rw-r--r-- | Marlin/src/pins/rambo/pins_RAMBO.h | 256 | ||||
| -rw-r--r-- | Marlin/src/pins/rambo/pins_SCOOVO_X9H.h | 159 |
5 files changed, 1010 insertions, 0 deletions
diff --git a/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h b/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h new file mode 100644 index 0000000..2ca2cc9 --- /dev/null +++ b/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h @@ -0,0 +1,196 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Einsy-Rambo pin assignments + */ + +#if NOT_TARGET(__AVR_ATmega2560__) + #error "Oops! Select 'Arduino Mega 2560 or Rambo' in 'Tools > Board.'" +#endif + +#define BOARD_INFO_NAME "Einsy Rambo" + +// +// TMC2130 Configuration_adv defaults for EinsyRambo +// +#if !AXIS_DRIVER_TYPE_X(TMC2130) || !AXIS_DRIVER_TYPE_Y(TMC2130) || !AXIS_DRIVER_TYPE_Z(TMC2130) || !AXIS_DRIVER_TYPE_E0(TMC2130) + #error "You must set ([XYZ]|E0)_DRIVER_TYPE to TMC2130 in Configuration.h for EinsyRambo." +#endif + +// TMC2130 Diag Pins (currently just for reference) +#define X_DIAG_PIN 64 +#define Y_DIAG_PIN 69 +#define Z_DIAG_PIN 68 +#define E0_DIAG_PIN 65 + +// +// Limit Switches +// +// Only use Diag Pins when SENSORLESS_HOMING is enabled for the TMC2130 drivers. +// Otherwise use a physical endstop based configuration. +// +// SERVO0_PIN and Z_MIN_PIN configuration for BLTOUCH sensor when combined with SENSORLESS_HOMING. +// + +#if DISABLED(SENSORLESS_HOMING) + + #define X_STOP_PIN 12 + #define Y_STOP_PIN 11 + #define Z_STOP_PIN 10 + +#else + + #define X_STOP_PIN X_DIAG_PIN + #define Y_STOP_PIN Y_DIAG_PIN + + #if ENABLED(BLTOUCH) + #define Z_STOP_PIN 11 // Y-MIN + #define SERVO0_PIN 10 // Z-MIN + #else + #define Z_STOP_PIN 10 + #endif + +#endif + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 10 +#endif + +// +// Filament Runout Sensor +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN 62 +#endif + +// +// Steppers +// +#define X_STEP_PIN 37 +#define X_DIR_PIN 49 +#define X_ENABLE_PIN 29 +#define X_CS_PIN 41 + +#define Y_STEP_PIN 36 +#define Y_DIR_PIN 48 +#define Y_ENABLE_PIN 28 +#define Y_CS_PIN 39 + +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 47 +#define Z_ENABLE_PIN 27 +#define Z_CS_PIN 67 + +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 26 +#define E0_CS_PIN 66 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // Analog Input +#define TEMP_1_PIN 1 // Analog Input +#define TEMP_BED_PIN 2 // Analog Input +#define TEMP_PROBE_PIN 3 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 3 +#define HEATER_BED_PIN 4 + +#ifndef FAN_PIN + #define FAN_PIN 8 +#endif + +#ifndef FAN1_PIN + #define FAN1_PIN 6 +#endif + +// +// Misc. Functions +// +#define SDSS 77 +#define LED_PIN 13 + +#ifndef CASE_LIGHT_PIN + #define CASE_LIGHT_PIN 9 +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +// use P1 connector for spindle pins +#define SPINDLE_LASER_PWM_PIN 9 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 18 // Pullup! +#define SPINDLE_DIR_PIN 19 + +// +// Průša i3 MK2 Multiplexer Support +// +#define E_MUX0_PIN 17 +#define E_MUX1_PIN 16 +#define E_MUX2_PIN 78 // 84 in MK2 Firmware, with BEEPER as 78 + +// +// LCD / Controller +// +#if HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL + + #define KILL_PIN 32 + + #if IS_ULTIPANEL || TOUCH_UI_ULTIPANEL + + #if ENABLED(CR10_STOCKDISPLAY) + #define LCD_PINS_RS 85 + #define LCD_PINS_ENABLE 71 + #define LCD_PINS_D4 70 + #define BTN_EN1 61 + #define BTN_EN2 59 + #else + #define LCD_PINS_RS 82 + #define LCD_PINS_ENABLE 61 + #define LCD_PINS_D4 59 + #define LCD_PINS_D5 70 + #define LCD_PINS_D6 85 + #define LCD_PINS_D7 71 + #define BTN_EN1 14 + #define BTN_EN2 72 + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + + #endif + + #define BTN_ENC 9 // AUX-2 + #define BEEPER_PIN 84 // AUX-4 + #define SD_DETECT_PIN 15 + + #endif // IS_ULTIPANEL || TOUCH_UI_ULTIPANEL +#endif // HAS_WIRED_LCD diff --git a/Marlin/src/pins/rambo/pins_EINSY_RETRO.h b/Marlin/src/pins/rambo/pins_EINSY_RETRO.h new file mode 100644 index 0000000..a6a4b65 --- /dev/null +++ b/Marlin/src/pins/rambo/pins_EINSY_RETRO.h @@ -0,0 +1,203 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Einsy-Retro pin assignments + */ + +#if NOT_TARGET(__AVR_ATmega2560__) + #error "Oops! Select 'Arduino Mega 2560 or Rambo' in 'Tools > Board.'" +#endif + +#define BOARD_INFO_NAME "Einsy Retro" + +// +// TMC2130 Configuration_adv defaults for EinsyRetro +// +#if !AXIS_DRIVER_TYPE_X(TMC2130) || !AXIS_DRIVER_TYPE_Y(TMC2130) || !AXIS_DRIVER_TYPE_Z(TMC2130) || !AXIS_DRIVER_TYPE_E0(TMC2130) + #error "You must set ([XYZ]|E0)_DRIVER_TYPE to TMC2130 in Configuration.h for EinsyRetro." +#endif + +// TMC2130 Diag Pins +#define X_DIAG_PIN 64 +#define Y_DIAG_PIN 69 +#define Z_DIAG_PIN 68 +#define E0_DIAG_PIN 65 + +// +// Limit Switches +// +// Only use Diag Pins when SENSORLESS_HOMING is enabled for the TMC2130 drivers. +// Otherwise use a physical endstop based configuration. +// +// SERVO0_PIN and Z_MIN_PIN configuration for BLTOUCH sensor when combined with SENSORLESS_HOMING. +// + +#if DISABLED(SENSORLESS_HOMING) + + #define X_MIN_PIN 12 // X- + #define Y_MIN_PIN 11 // Y- + #define Z_MIN_PIN 10 // Z- + #define X_MAX_PIN 81 // X+ + #define Y_MAX_PIN 57 // Y+ + +#else + + #if X_HOME_DIR < 0 + #define X_MIN_PIN X_DIAG_PIN + #define X_MAX_PIN 81 // X+ + #else + #define X_MIN_PIN 12 // X- + #define X_MAX_PIN X_DIAG_PIN + #endif + + #if Y_HOME_DIR < 0 + #define Y_MIN_PIN Y_DIAG_PIN + #define Y_MAX_PIN 57 // Y+ + #else + #define Y_MIN_PIN 11 // Y- + #define Y_MAX_PIN Y_DIAG_PIN + #endif + + #if ENABLED(BLTOUCH) + #define Z_MIN_PIN 11 // Y-MIN + #define SERVO0_PIN 10 // Z-MIN + #else + #define Z_MIN_PIN 10 + #endif + +#endif + +#define Z_MAX_PIN 7 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 10 +#endif + +// +// Steppers +// +#define X_STEP_PIN 37 +#define X_DIR_PIN 49 +#define X_ENABLE_PIN 29 +#define X_CS_PIN 41 + +#define Y_STEP_PIN 36 +#define Y_DIR_PIN 48 +#define Y_ENABLE_PIN 28 +#define Y_CS_PIN 39 + +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 47 +#define Z_ENABLE_PIN 27 +#define Z_CS_PIN 67 + +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 26 +#define E0_CS_PIN 66 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // Analog Input +#define TEMP_1_PIN 1 // Analog Input +#define TEMP_BED_PIN 2 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 3 +#define HEATER_BED_PIN 4 + +#ifndef FAN_PIN + #define FAN_PIN 8 +#endif +#define FAN1_PIN 6 + +// +// Misc. Functions +// +#define SDSS 53 +#define LED_PIN 13 + +#ifndef CASE_LIGHT_PIN + #define CASE_LIGHT_PIN 9 +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +// use P1 connector for spindle pins +#define SPINDLE_LASER_PWM_PIN 9 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 18 // Pullup! +#define SPINDLE_DIR_PIN 19 + +// +// Průša i3 MK2 Multiplexer Support +// +#define E_MUX0_PIN 17 +#define E_MUX1_PIN 16 +#define E_MUX2_PIN 78 // 84 in MK2 Firmware, with BEEPER as 78 + +// +// LCD / Controller +// +#if ANY(HAS_WIRED_LCD, TOUCH_UI_ULTIPANEL, TOUCH_UI_FTDI_EVE) + + #define KILL_PIN 32 + + #if ANY(IS_ULTIPANEL, TOUCH_UI_ULTIPANEL, TOUCH_UI_FTDI_EVE) + + #if ENABLED(CR10_STOCKDISPLAY) + #define LCD_PINS_RS 85 + #define LCD_PINS_ENABLE 71 + #define LCD_PINS_D4 70 + #define BTN_EN1 18 + #define BTN_EN2 19 + #else + #define LCD_PINS_RS 82 + #define LCD_PINS_ENABLE 18 // On 0.6b, use 61 + #define LCD_PINS_D4 19 // On 0.6b, use 59 + #define LCD_PINS_D5 70 + #define LCD_PINS_D6 85 + #define LCD_PINS_D7 71 + #define BTN_EN1 14 + #define BTN_EN2 72 + #endif + + #define BTN_ENC 9 // AUX-2 + #define BEEPER_PIN 84 // AUX-4 + + #define SD_DETECT_PIN 15 + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + + #endif // IS_ULTIPANEL || TOUCH_UI_ULTIPANEL || TOUCH_UI_FTDI_EVE + +#endif // HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL || TOUCH_UI_FTDI_EVE diff --git a/Marlin/src/pins/rambo/pins_MINIRAMBO.h b/Marlin/src/pins/rambo/pins_MINIRAMBO.h new file mode 100644 index 0000000..4dcf358 --- /dev/null +++ b/Marlin/src/pins/rambo/pins_MINIRAMBO.h @@ -0,0 +1,196 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Mini-RAMBo pin assignments + */ + +#if NOT_TARGET(__AVR_ATmega2560__) + #error "Oops! Select 'RAMBo' in 'Tools > Board' or the Mega2560 environment in PlatformIO." +#endif + +#if MB(MINIRAMBO_10A) + #define BOARD_INFO_NAME "Mini RAMBo 1.0a" +#else + #define BOARD_INFO_NAME "Mini RAMBo" +#endif + +// +// Limit Switches +// +#define X_MIN_PIN 12 +#define X_MAX_PIN 30 +#define Y_MIN_PIN 11 +#define Y_MAX_PIN 24 +#define Z_MIN_PIN 10 +#define Z_MAX_PIN 23 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 23 +#endif + +// +// Steppers +// +#define X_STEP_PIN 37 +#define X_DIR_PIN 48 +#define X_ENABLE_PIN 29 + +#define Y_STEP_PIN 36 +#define Y_DIR_PIN 49 +#define Y_ENABLE_PIN 28 + +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 47 +#define Z_ENABLE_PIN 27 + +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 26 + +// Microstepping pins - Mapping not from fastio.h (?) +#define X_MS1_PIN 40 +#define X_MS2_PIN 41 +#define Y_MS1_PIN 69 +#define Y_MS2_PIN 39 +#define Z_MS1_PIN 68 +#define Z_MS2_PIN 67 +#define E0_MS1_PIN 65 +#define E0_MS2_PIN 66 + +#define MOTOR_CURRENT_PWM_XY_PIN 46 +#define MOTOR_CURRENT_PWM_Z_PIN 45 +#define MOTOR_CURRENT_PWM_E_PIN 44 +// Motor current PWM conversion, PWM value = MotorCurrentSetting * 255 / range +#ifndef MOTOR_CURRENT_PWM_RANGE + #define MOTOR_CURRENT_PWM_RANGE 2000 +#endif +#define DEFAULT_PWM_MOTOR_CURRENT {1300, 1300, 1250} + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // Analog Input +#define TEMP_1_PIN 1 // Analog Input +#define TEMP_BED_PIN 2 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 3 +#define HEATER_1_PIN 7 +#if !MB(MINIRAMBO_10A) + #define HEATER_2_PIN 6 +#endif +#define HEATER_BED_PIN 4 + +#ifndef FAN_PIN + #define FAN_PIN 8 +#endif +#define FAN1_PIN 6 + +// +// Misc. Functions +// +#define SDSS 53 +#define LED_PIN 13 +#if !MB(MINIRAMBO_10A) + #define CASE_LIGHT_PIN 9 +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +// use P1 connector for spindle pins +#define SPINDLE_LASER_PWM_PIN 9 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 18 // Pullup! +#define SPINDLE_DIR_PIN 19 + +// +// Průša i3 MK2 Multiplexer Support +// +#define E_MUX0_PIN 17 +#define E_MUX1_PIN 16 +#if !MB(MINIRAMBO_10A) + #define E_MUX2_PIN 78 // 84 in MK2 Firmware, with BEEPER as 78 +#endif + +// +// LCD / Controller +// +#if HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL + + #if !MB(MINIRAMBO_10A) + #define KILL_PIN 32 + #endif + + #if IS_ULTIPANEL || TOUCH_UI_ULTIPANEL + + #if MB(MINIRAMBO_10A) + + #define BEEPER_PIN 78 + + #define BTN_EN1 80 + #define BTN_EN2 73 + #define BTN_ENC 21 + + #define LCD_PINS_RS 38 + #define LCD_PINS_ENABLE 5 + #define LCD_PINS_D4 14 + #define LCD_PINS_D5 15 + #define LCD_PINS_D6 32 + #define LCD_PINS_D7 31 + + #define SD_DETECT_PIN 72 + + #else // !MINIRAMBO_10A + + // AUX-4 + #define BEEPER_PIN 84 + + // AUX-2 + #define BTN_EN1 14 + #define BTN_EN2 72 + #define BTN_ENC 9 + + #define LCD_PINS_RS 82 + #define LCD_PINS_ENABLE 18 + #define LCD_PINS_D4 19 + #define LCD_PINS_D5 70 + #define LCD_PINS_D6 85 + #define LCD_PINS_D7 71 + + #define SD_DETECT_PIN 15 + + #endif // !MINIRAMBO_10A + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + + #endif // IS_ULTIPANEL || TOUCH_UI_ULTIPANEL + +#endif // HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL diff --git a/Marlin/src/pins/rambo/pins_RAMBO.h b/Marlin/src/pins/rambo/pins_RAMBO.h new file mode 100644 index 0000000..be2317b --- /dev/null +++ b/Marlin/src/pins/rambo/pins_RAMBO.h @@ -0,0 +1,256 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * IMPORTANT NOTE: + * Rambo users should be sure to compile Marlin using either the RAMBo + * board type if using the Arduino IDE - available via the link below - or + * the 'rambo' environment if using platformio, by specifying '-e rambo' on + * the command line or by changing the value of the 'env_default' variable to + * 'rambo' in the supplied platformio.ini. + * + * If you don't compile using the proper board type, the RAMBo's extended + * pins will likely be unavailable and accessories/addons may not work. + * + * Instructions for installing the Arduino RAMBo board type for the + * Arduino IDE are available at: + * https://reprap.org/wiki/Rambo_firmware + */ + +/** + * Rambo pin assignments + */ + +#if NOT_TARGET(__AVR_ATmega2560__) + #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#endif + +#define BOARD_INFO_NAME "Rambo" + +// +// Servos +// +#define SERVO0_PIN 22 // Motor header MX1 +#define SERVO1_PIN 23 // Motor header MX2 +#define SERVO2_PIN 24 // Motor header MX3 +#define SERVO3_PIN 5 // PWM header pin 5 + +// +// Limit Switches +// +#define X_MIN_PIN 12 +#define X_MAX_PIN 24 +#define Y_MIN_PIN 11 +#define Y_MAX_PIN 23 +#define Z_MIN_PIN 10 +#define Z_MAX_PIN 30 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 30 +#endif + +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN 5 +#endif + +// +// Steppers +// +#define X_STEP_PIN 37 +#define X_DIR_PIN 48 +#define X_ENABLE_PIN 29 + +#define Y_STEP_PIN 36 +#define Y_DIR_PIN 49 +#define Y_ENABLE_PIN 28 + +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 47 +#define Z_ENABLE_PIN 27 + +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 26 + +#define E1_STEP_PIN 33 +#define E1_DIR_PIN 42 +#define E1_ENABLE_PIN 25 + +// Microstepping pins - Mapping not from fastio.h (?) +#define X_MS1_PIN 40 +#define X_MS2_PIN 41 +#define Y_MS1_PIN 69 +#define Y_MS2_PIN 39 +#define Z_MS1_PIN 68 +#define Z_MS2_PIN 67 +#define E0_MS1_PIN 65 +#define E0_MS2_PIN 66 +#define E1_MS1_PIN 63 +#define E1_MS2_PIN 64 + +#define DIGIPOTSS_PIN 38 +#define DIGIPOT_CHANNELS { 4, 5, 3, 0, 1 } // X Y Z E0 E1 digipot channels to stepper driver mapping +#ifndef DIGIPOT_MOTOR_CURRENT + #define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // Analog Input +#define TEMP_1_PIN 1 // Analog Input +#define TEMP_BED_PIN 2 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 9 +#define HEATER_1_PIN 7 +#define HEATER_2_PIN 6 +#define HEATER_BED_PIN 3 + +#ifndef FAN_PIN + #define FAN_PIN 8 +#endif +#define FAN1_PIN 6 +#define FAN2_PIN 2 + +// +// Misc. Functions +// +#define SDSS 53 +#define LED_PIN 13 +#define PS_ON_PIN 4 + +#ifndef CASE_LIGHT_PIN + #define CASE_LIGHT_PIN 46 +#endif + +#ifndef FILWIDTH_PIN + #define FILWIDTH_PIN 3 // Analog Input +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_PWM_PIN 45 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 31 // Pullup! +#define SPINDLE_DIR_PIN 32 + +// +// SPI for Max6675 or Max31855 Thermocouple +// +#ifndef MAX6675_SS_PIN + #define MAX6675_SS_PIN 32 // SPINDLE_DIR_PIN / STAT_LED_BLUE_PIN +#endif + +// +// M7/M8/M9 - Coolant Control +// +#define COOLANT_MIST_PIN 22 +#define COOLANT_FLOOD_PIN 44 + +// +// Průša i3 MK2 Multiplexer Support +// +#define E_MUX0_PIN 17 +#define E_MUX1_PIN 16 +#define E_MUX2_PIN 84 // 84 in MK2 Firmware + +// +// LCD / Controller +// +#if HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL + + #define KILL_PIN 80 + + #if IS_ULTIPANEL || TOUCH_UI_ULTIPANEL + + #define LCD_PINS_RS 70 + #define LCD_PINS_ENABLE 71 + #define LCD_PINS_D4 72 + #define LCD_PINS_D5 73 + #define LCD_PINS_D6 74 + #define LCD_PINS_D7 75 + + #if ANY(VIKI2, miniVIKI) + #define BEEPER_PIN 44 + // NB: Panucatt's Viki 2.0 wiring diagram (v1.2) indicates that the + // beeper/buzzer is connected to pin 33; however, the pin used in the + // diagram is actually pin 44, so this is correct. + + #define DOGLCD_A0 70 + #define DOGLCD_CS 71 + #define LCD_SCREEN_ROT_180 + + #define BTN_EN1 85 + #define BTN_EN2 84 + #define BTN_ENC 83 + + #define SD_DETECT_PIN -1 // Pin 72 if using easy adapter board + + #define STAT_LED_RED_PIN 22 + #define STAT_LED_BLUE_PIN 32 + + #else // !VIKI2 && !miniVIKI + + #define BEEPER_PIN 79 // AUX-4 + + // AUX-2 + #define BTN_EN1 76 + #define BTN_EN2 77 + #define BTN_ENC 78 + + #define SD_DETECT_PIN 81 + + #endif // !VIKI2 && !miniVIKI + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + + #else // !IS_NEWPANEL - old style panel with shift register + + // No Beeper added + #define BEEPER_PIN 33 + + // Buttons attached to a shift register + // Not wired yet + //#define SHIFT_CLK_PIN 38 + //#define SHIFT_LD_PIN 42 + //#define SHIFT_OUT_PIN 40 + //#define SHIFT_EN_PIN 17 + + #define LCD_PINS_RS 75 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #define LCD_PINS_D7 29 + + #endif // !IS_NEWPANEL + +#endif // HAS_WIRED_LCD diff --git a/Marlin/src/pins/rambo/pins_SCOOVO_X9H.h b/Marlin/src/pins/rambo/pins_SCOOVO_X9H.h new file mode 100644 index 0000000..5680b00 --- /dev/null +++ b/Marlin/src/pins/rambo/pins_SCOOVO_X9H.h @@ -0,0 +1,159 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/************************************************ + * Rambo pin assignments MODIFIED FOR Scoovo X9H + ************************************************/ + +#if NOT_TARGET(__AVR_ATmega2560__) + #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#endif + +#define BOARD_INFO_NAME "Scoovo X9H" + +// +// Servos +// +#define SERVO0_PIN 22 // Motor header MX1 +#define SERVO1_PIN 23 // Motor header MX2 +#define SERVO2_PIN 24 // Motor header MX3 +#define SERVO3_PIN 5 // PWM header pin 5 + +// +// Limit Switches +// +#define X_MIN_PIN 12 +#define X_MAX_PIN 24 +#define Y_MIN_PIN 11 +#define Y_MAX_PIN 23 +#define Z_MIN_PIN 10 +#define Z_MAX_PIN 30 + +// +// Z Probe (when not Z_MIN_IN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 30 +#endif + +// +// Steppers +// +#define X_STEP_PIN 37 +#define X_DIR_PIN 48 +#define X_ENABLE_PIN 29 + +#define Y_STEP_PIN 36 +#define Y_DIR_PIN 49 +#define Y_ENABLE_PIN 28 + +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 47 +#define Z_ENABLE_PIN 27 + +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 26 + +#define E1_STEP_PIN 33 +#define E1_DIR_PIN 42 +#define E1_ENABLE_PIN 25 + +// Microstepping pins - Mapping not from fastio.h (?) +#define X_MS1_PIN 40 +#define X_MS2_PIN 41 +#define Y_MS1_PIN 69 +#define Y_MS2_PIN 39 +#define Z_MS1_PIN 68 +#define Z_MS2_PIN 67 +#define E0_MS1_PIN 65 +#define E0_MS2_PIN 66 +#define E1_MS1_PIN 63 +#define E1_MS2_PIN 64 + +#define DIGIPOTSS_PIN 38 +#define DIGIPOT_CHANNELS { 4, 5, 3, 0, 1 } // X Y Z E0 E1 digipot channels to stepper driver mapping + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // Analog Input +#define TEMP_BED_PIN 7 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 9 +#define HEATER_1_PIN 7 +#define HEATER_BED_PIN 3 + +#ifndef FAN_PIN + #define FAN_PIN 8 +#endif +#define FAN1_PIN 6 +#define FAN2_PIN 2 + +// +// Misc. Functions +// +#define SDSS 53 +#define LED_PIN 13 +#define PS_ON_PIN 4 + +#ifndef FILWIDTH_PIN + #define FILWIDTH_PIN 3 // Analog Input +#endif + +// +// LCD / Controller +// +#define LCD_PINS_RS 70 // Ext2_5 +#define LCD_PINS_ENABLE 71 // Ext2_7 +#define LCD_PINS_D4 72 // Ext2_9 ? +#define LCD_PINS_D5 73 // Ext2_11 ? +#define LCD_PINS_D6 74 // Ext2_13 +#define LCD_PINS_D7 75 // Ext2_15 ? +#define BEEPER_PIN -1 + +#define BTN_HOME 80 // Ext_16 +#define BTN_CENTER 81 // Ext_14 +#define BTN_ENC BTN_CENTER +#define BTN_RIGHT 82 // Ext_12 +#define BTN_LEFT 83 // Ext_10 +#define BTN_UP 84 // Ext2_8 +#define BTN_DOWN 85 // Ext2_6 + +#define HOME_PIN BTN_HOME + +#if ANY(VIKI2, miniVIKI) + #define BEEPER_PIN 44 + // Pins for DOGM SPI LCD Support + #define DOGLCD_A0 70 + #define DOGLCD_CS 71 + #define LCD_SCREEN_ROT_180 + + #define SD_DETECT_PIN -1 // Pin 72 if using easy adapter board + + #define STAT_LED_RED_PIN 22 + #define STAT_LED_BLUE_PIN 32 +#endif // VIKI2/miniVIKI |