diff options
| author | Georgiy Bondarenko <69736697+nehilo@users.noreply.github.com> | 2021-03-04 20:54:23 +0300 |
|---|---|---|
| committer | Georgiy Bondarenko <69736697+nehilo@users.noreply.github.com> | 2021-03-04 20:54:23 +0300 |
| commit | e8701195e66f2d27ffe17fb514eae8173795aaf7 (patch) | |
| tree | 9f519c4abf6556b9ae7190a6210d87ead1dfadde /Marlin/src/pins/sanguino | |
| download | kp3s-lgvl-e8701195e66f2d27ffe17fb514eae8173795aaf7.tar.xz kp3s-lgvl-e8701195e66f2d27ffe17fb514eae8173795aaf7.zip | |
Initial commit
Diffstat (limited to 'Marlin/src/pins/sanguino')
23 files changed, 2577 insertions, 0 deletions
diff --git a/Marlin/src/pins/sanguino/pins_ANET_10.h b/Marlin/src/pins/sanguino/pins_ANET_10.h new file mode 100644 index 0000000..fb1b6db --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_ANET_10.h @@ -0,0 +1,289 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Anet V1.0 board pin assignments + */ + +/** + * Rev B 16 JUN 2017 + * + * 1) no longer uses Sanguino files to define some of the pins + * 2) added pointers to useable Arduino IDE extensions + */ + +/** + * The standard Arduino IDE extension (board manager) for this board + * is located at https://github.com/SkyNet3D/anet-board. + * + * Installation instructions are on that page. + * + * After copying the files to the appropriate location, restart Arduino and + * you'll see "Anet V1.0" and "Anet V1.0 (Optiboot)" in the boards list. + * + * "Anet V1.0" uses the bootloader that was installed on the board when + * it shipped from the factory. + * + * "Anet V1.0 (Optiboot)" frees up another 3K of FLASH. You'll need to burn + * a new bootloader to the board to be able to automatically download a + * compiled image. + */ + +/** + * Another usable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +/** + * To burn a new bootloader: + * + * 1. Connect your programmer to the board. + * 2. In the Arduino IDE select the board and then select the programmer. + * 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. + * 4. The programmer is no longer needed. Remove it. + */ + +/** + * Additional info: + * + * Anet Schematics - https://github.com/ralf-e/ANET-3D-Board-V1.0 + * Wiring RRDFG Smart Controller - https://www.thingiverse.com/thing:2103748 + * SkyNet3D Anet software development - https://github.com/SkyNet3D/Marlin/ + * Anet Users / Skynet SW on Facebook - https://www.facebook.com/skynet3ddevelopment/ + * + * Many thanks to Hans Raaf (@oderwat) for developing the Anet-specific software and supporting the Anet community. + */ + +#if NOT_TARGET(__AVR_ATmega1284P__) + #error "Oops! Select 'Sanguino' in 'Tools > Board' and 'ATmega1284P' in 'Tools > Processor.' (For PlatformIO, use 'melzi' or 'melzi_optiboot.')" +#endif + +#define BOARD_INFO_NAME "Anet 1.0" + +// +// Limit Switches +// +#define X_STOP_PIN 18 +#define Y_STOP_PIN 19 +#define Z_STOP_PIN 20 + +// +// Steppers +// +#define X_STEP_PIN 15 +#define X_DIR_PIN 21 +#define X_ENABLE_PIN 14 + +#define Y_STEP_PIN 22 +#define Y_DIR_PIN 23 +#define Y_ENABLE_PIN 14 + +#define Z_STEP_PIN 3 +#define Z_DIR_PIN 2 +#define Z_ENABLE_PIN 26 + +#define E0_STEP_PIN 1 +#define E0_DIR_PIN 0 +#define E0_ENABLE_PIN 14 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 7 // Analog Input (pin 33 extruder) +#define TEMP_BED_PIN 6 // Analog Input (pin 34 bed) + +// +// Heaters / Fans +// +#define HEATER_0_PIN 13 // (extruder) +#define HEATER_BED_PIN 12 // (bed) + +#ifndef FAN_PIN + #define FAN_PIN 4 +#endif + +// +// Misc. Functions +// +#define SDSS 31 +#define LED_PIN -1 + +/** + * LCD / Controller + * + * Only the following displays are supported: + * ZONESTAR_LCD + * ANET_FULL_GRAPHICS_LCD(_ALT_WIRING)? + * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + */ + +#if HAS_WIRED_LCD + + #define LCD_SDSS 28 + + #if HAS_ADC_BUTTONS + + #define SERVO0_PIN 27 // free for BLTouch/3D-Touch + #define LCD_PINS_RS 28 + #define LCD_PINS_ENABLE 29 + #define LCD_PINS_D4 10 + #define LCD_PINS_D5 11 + #define LCD_PINS_D6 16 + #define LCD_PINS_D7 17 + #define ADC_KEYPAD_PIN 1 + + #elif IS_RRD_FG_SC + + // Pin definitions for the Anet A6 Full Graphics display and the RepRapDiscount Full Graphics + // display using an adapter board // https://go.aisler.net/benlye/anet-lcd-adapter/pcb + // See below for alternative pin definitions for use with https://www.thingiverse.com/thing:2103748 + + #if ENABLED(ANET_FULL_GRAPHICS_LCD_ALT_WIRING) + #define SERVO0_PIN 30 + #define BEEPER_PIN 27 + #define LCD_PINS_RS 29 + #define LCD_PINS_ENABLE 16 + #define LCD_PINS_D4 11 + #define BTN_EN1 28 + #define BTN_EN2 10 + #define BTN_ENC 17 + #define BOARD_ST7920_DELAY_1 DELAY_NS(250) + #define BOARD_ST7920_DELAY_2 DELAY_NS(250) + #define BOARD_ST7920_DELAY_3 DELAY_NS(250) + #else + #define SERVO0_PIN 29 // free for BLTouch/3D-Touch + #define BEEPER_PIN 17 + #define LCD_PINS_RS 27 + #define LCD_PINS_ENABLE 28 + #define LCD_PINS_D4 30 + #define BTN_EN1 11 + #define BTN_EN2 10 + #define BTN_ENC 16 + #define BOARD_ST7920_DELAY_1 DELAY_NS(0) + #define BOARD_ST7920_DELAY_2 DELAY_NS(63) + #define BOARD_ST7920_DELAY_3 DELAY_NS(125) + #endif + + #endif + +#else + #define SERVO0_PIN 27 +#endif + +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN SERVO0_PIN +#endif + +/** + * ==================================================================== + * =============== Alternative RepRapDiscount Wiring ================== + * ==================================================================== + * + * An alternative wiring scheme for the RepRapDiscount Full Graphics Display is + * published by oderwat on Thingiverse at https://www.thingiverse.com/thing:2103748. + * + * Using that adapter requires changing the pin definition as follows: + * #define SERVO0_PIN 27 // free for BLTouch/3D-Touch + * #define BEEPER_PIN 28 + * #define LCD_PINS_RS 30 + * #define LCD_PINS_ENABLE 29 + * #define LCD_PINS_D4 17 + * + * The BLTouch pin becomes LCD:3 + */ + +/** + * ==================================================================== + * ===================== LCD PINOUTS ================================== + * ==================================================================== + * + * Anet V1.0 controller | ZONESTAR_LCD | ANET_FULL_ | RepRapDiscount Full | Thingiverse RepRap wiring + * physical logical alt | | GRAPHICS_LCD | Graphics Display Wiring | https://www.thingiverse + * pin pin functions | | | | .com/thing:2103748 + *------------------------------------------------------------------------------------------------------------------------ + * ANET-J3.1 8 *** | N/A | J3_TX *** | | + * ANET-J3.2 9 *** | N/A | J3_RX *** | | + * ANET-J3.3 6 MISO | N/A | MISO *** | EXP2.1 MISO | EXP2.1 MISO + * ANET-J3.4 +5V | N/A | +5V | | + * ANET-J3.5 7 SCK | N/A | SCK *** | EXP2.2 SCK | EXP2.2 SCK + * ANET-J3.6 5 MOSI | N/A | MOSI *** | EXP2.6 MOSI | EXP2.6 MOSI + * ANET-J3.7 !RESET | N/A | button | EXP2.8 panel button | EXP2.8 panel button + * ANET-J3.8 GND | N/A | GND | EXP2.9 GND | EXP2.9 GND + * ANET-J3.9 4 Don't use | N/A | N/C | | + * ANET-J3.10 +3.3V | N/A | +3.3V *** | | + * | | | | + * | | | | + * ANET-LCD.1 GND | GND | GND | EXP1.9 GND | EXP1.9 GND + * ANET-LCD.2 +5V | +5V | +5V | EXP1.10 +5V | EXP1.10 +5V + * ANET-LCD.3 27 A4 | N/C * | LCD_PINS_RS | EXP1.4 LCD_PINS_RS | EXP2.4 SDSS or N/C * + * ANET-LCD.4 10 | LCD_PINS_D4 | BTN_EN2 | EXP2.3 BTN_EN2 | EXP2.3 BTN_EN2 + * ANET-LCD.5 28 A3 | LCD_PINS_RS | LCD_PINS_ENABLE | EXP1.3 LCD_PINS_ENABLE | EXP1.1 BEEPER_PIN + * ANET-LCD.6 11 | LCD_PINS_D5 | BTN_EN1 | EXP2.5 BTN_EN1 | EXP2.5 BTN_EN1 + * ANET-LCD.7 29 A2 | LCD_PINS_ENABLE | N/C * | EXP2.4 SDSS or N/C * | EXP1.3 LCD_PINS_ENABLE + * ANET-LCD.8 16 SCL | LCD_PINS_D6 | BTN_ENC | EXP1.2 BTN_ENC | EXP1.2 BTN_ENC + * ANET-LCD.9 30 A1 | ADC_KEYPAD_PIN ** | LCD_PINS_D4 | EXP1.5 LCD_PINS_D4 | EXP1.4 LCD_PINS_RS + * ANET-LCD.10 17 SDA | LCD_PINS_D7 | BEEPER_PIN | EXP1.1 BEEPER_PIN | EXP1.5 LCD_PINS_D4 + * + * N/C * - if not connected to the LCD can be used for BLTouch servo input + * ** - analog pin -WITHOUT a pullup + * *** - only connected to something if the Bluetooth module is populated + */ + +/** + * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + * physical pin function + * EXP1.1 BEEPER + * EXP1.2 BTN_ENC + * EXP1.3 LCD_PINS_ENABLE + * EXP1.4 LCD_PINS_RS + * EXP1.5 LCD_PINS_D4 + * EXP1.6 LCD_PINS_D5 (not used) + * EXP1.7 LCD_PINS_D6 (not used) + * EXP1.8 LCD_PINS_D7 (not used) + * EXP1.9 GND + * EXP1.10 VCC + * + * + * EXP2.1 MISO + * EXP2.2 SCK + * EXP2.3 BTN_EN2 + * EXP2.4 SDSS + * EXP2.5 BTN_EN1 + * EXP2.6 MOSI + * EXP2.7 SD_DETECT_PIN + * EXP2.8 button + * EXP2.9 GND + * EXP2.10 NC + */ diff --git a/Marlin/src/pins/sanguino/pins_AZTEEG_X1.h b/Marlin/src/pins/sanguino/pins_AZTEEG_X1.h new file mode 100644 index 0000000..c3c38eb --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_AZTEEG_X1.h @@ -0,0 +1,30 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Azteeg X1 pin assignments + */ + +#define BOARD_INFO_NAME "Azteeg X1" + +#include "pins_SANGUINOLOLU_12.h" diff --git a/Marlin/src/pins/sanguino/pins_GEN3_MONOLITHIC.h b/Marlin/src/pins/sanguino/pins_GEN3_MONOLITHIC.h new file mode 100644 index 0000000..29905c1 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_GEN3_MONOLITHIC.h @@ -0,0 +1,99 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Gen3 Monolithic Electronics pin assignments + */ + +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +#if NOT_TARGET(__AVR_ATmega644P__) + #error "Oops! Select 'Sanguino' in 'Tools > Board.'" +#endif + +#define BOARD_INFO_NAME "Gen3 Monolithic" +#define DEBUG_PIN 0 + +// +// Limit Switches +// +#define X_STOP_PIN 20 +#define Y_STOP_PIN 25 +#define Z_STOP_PIN 30 + +// +// Steppers +// +#define X_STEP_PIN 15 +#define X_DIR_PIN 18 +#define X_ENABLE_PIN 24 // actually uses Y_enable_pin + +#define Y_STEP_PIN 23 +#define Y_DIR_PIN 22 +#define Y_ENABLE_PIN 24 // shared with X_enable_pin + +#define Z_STEP_PIN 27 +#define Z_DIR_PIN 28 +#define Z_ENABLE_PIN 29 + +#define E0_STEP_PIN 12 +#define E0_DIR_PIN 17 +#define E0_ENABLE_PIN 3 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // Analog Input + +// +// Heaters +// +#define HEATER_0_PIN 16 + +// +// Misc. Functions +// +#define PS_ON_PIN 14 // Alex, does this work on the card? + +// Alex extras from Gen3+ diff --git a/Marlin/src/pins/sanguino/pins_GEN3_PLUS.h b/Marlin/src/pins/sanguino/pins_GEN3_PLUS.h new file mode 100644 index 0000000..33fc233 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_GEN3_PLUS.h @@ -0,0 +1,99 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Gen3+ pin assignments + */ + +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the SANGUINO board and then select the CPU. + */ + +#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega1284P__) + #error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644P' or 'ATmega1284P' in 'Tools > Processor.'" +#endif + +#define BOARD_INFO_NAME "Gen3+" + +// +// Limit Switches +// +#define X_STOP_PIN 20 +#define Y_STOP_PIN 25 +#define Z_STOP_PIN 30 + +// +// Steppers +// +#define X_STEP_PIN 15 +#define X_DIR_PIN 18 +#define X_ENABLE_PIN 19 + +#define Y_STEP_PIN 23 +#define Y_DIR_PIN 22 +#define Y_ENABLE_PIN 24 + +#define Z_STEP_PIN 27 +#define Z_DIR_PIN 28 +#define Z_ENABLE_PIN 29 + +#define E0_STEP_PIN 17 +#define E0_DIR_PIN 21 +#define E0_ENABLE_PIN 13 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // Analog Input (pin 33 extruder) +#define TEMP_BED_PIN 5 // Analog Input (pin 34 bed) + +// +// Heaters +// +#define HEATER_0_PIN 12 +#define HEATER_BED_PIN 16 + +// +// Misc. Functions +// +#define SDSS 4 +#define PS_ON_PIN 14 diff --git a/Marlin/src/pins/sanguino/pins_GEN6.h b/Marlin/src/pins/sanguino/pins_GEN6.h new file mode 100644 index 0000000..bfca8e9 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_GEN6.h @@ -0,0 +1,121 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Gen6 pin assignments + */ + + /** + * Rev B 26 DEC 2016 + * + * 1) added pointer to a current Arduino IDE extension + * 2) added support for M3, M4 & M5 spindle control commands + * 3) added case light pin definition + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega1284P__) + #error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644P' or 'ATmega1284P' in 'Tools > Processor.'" +#endif + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "Gen6" +#endif + +// +// Limit Switches +// +#define X_STOP_PIN 20 +#define Y_STOP_PIN 25 +#define Z_STOP_PIN 30 + +// +// Steppers +// +#define X_STEP_PIN 15 +#define X_DIR_PIN 18 +#define X_ENABLE_PIN 19 + +#define Y_STEP_PIN 23 +#define Y_DIR_PIN 22 +#define Y_ENABLE_PIN 24 + +#define Z_STEP_PIN 27 +#define Z_DIR_PIN 28 +#define Z_ENABLE_PIN 29 + +#define E0_STEP_PIN 4 // Edited @ EJE Electronics 20100715 +#define E0_DIR_PIN 2 // Edited @ EJE Electronics 20100715 +#define E0_ENABLE_PIN 3 // Added @ EJE Electronics 20100715 + +// +// Temperature Sensor +// +#define TEMP_0_PIN 5 // Analog Input + +// +// Heaters +// +#define HEATER_0_PIN 14 // changed @ rkoeppl 20110410 + +#if !MB(GEN6) + #define HEATER_BED_PIN 1 // changed @ rkoeppl 20110410 + #define TEMP_BED_PIN 0 // Analog Input +#endif + +// +// Misc. Functions +// +#define SDSS 17 +#define DEBUG_PIN 0 + +#ifndef CASE_LIGHT_PIN + #define CASE_LIGHT_PIN 16 // Hardware PWM +#endif + +// RS485 pins +#define TX_ENABLE_PIN 12 +#define RX_ENABLE_PIN 13 + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENA_PIN 5 // Pullup or pulldown! +#define SPINDLE_LASER_PWM_PIN 16 // Hardware PWM +#define SPINDLE_DIR_PIN 6 diff --git a/Marlin/src/pins/sanguino/pins_GEN6_DELUXE.h b/Marlin/src/pins/sanguino/pins_GEN6_DELUXE.h new file mode 100644 index 0000000..9c63570 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_GEN6_DELUXE.h @@ -0,0 +1,54 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Gen6 Deluxe pin assignments + */ + +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the SANGUINO board and then select the CPU. + */ + + +#define BOARD_INFO_NAME "Gen6 Deluxe" + +#include "pins_GEN6.h" diff --git a/Marlin/src/pins/sanguino/pins_GEN7_12.h b/Marlin/src/pins/sanguino/pins_GEN7_12.h new file mode 100644 index 0000000..9db7d72 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_GEN7_12.h @@ -0,0 +1,147 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Gen7 v1.1, v1.2, v1.3 pin assignments + */ + + /** + * Rev B 26 DEC 2016 + * + * 1) added pointer to a current Arduino IDE extension + * 2) added support for M3, M4 & M5 spindle control commands + * 3) added case light pin definition + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega644__, __AVR_ATmega1284P__) + #error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644', 'ATmega644P', or 'ATmega1284P' in 'Tools > Processor.'" +#endif + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "Gen7 v1.1 / 1.2" +#endif + +#ifndef GEN7_VERSION + #define GEN7_VERSION 12 // v1.x +#endif + +// +// Limit Switches +// +#define X_MIN_PIN 7 +#define Y_MIN_PIN 5 +#define Z_MIN_PIN 1 +#define Z_MAX_PIN 0 +#define Y_MAX_PIN 2 +#define X_MAX_PIN 6 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 0 +#endif + +// +// Steppers +// +#define X_STEP_PIN 19 +#define X_DIR_PIN 18 +#define X_ENABLE_PIN 24 + +#define Y_STEP_PIN 23 +#define Y_DIR_PIN 22 +#define Y_ENABLE_PIN 24 + +#define Z_STEP_PIN 26 +#define Z_DIR_PIN 25 +#define Z_ENABLE_PIN 24 + +#define E0_STEP_PIN 28 +#define E0_DIR_PIN 27 +#define E0_ENABLE_PIN 24 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 1 // Analog Input +#define TEMP_BED_PIN 2 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 4 +#define HEATER_BED_PIN 3 + +#if !defined(FAN_PIN) && GEN7_VERSION < 13 // Gen7 v1.3 removed the fan pin + #define FAN_PIN 31 +#endif + +// +// Misc. Functions +// +#define PS_ON_PIN 15 + +#if GEN7_VERSION < 13 + #define CASE_LIGHT_PIN 16 // Hardware PWM +#else // Gen7 v1.3 removed the I2C connector & signals so need to get PWM off the PC power supply header + #define CASE_LIGHT_PIN 15 // Hardware PWM +#endif + +// All these generations of Gen7 supply thermistor power +// via PS_ON, so ignore bad thermistor readings +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 + +#define DEBUG_PIN 0 + +// RS485 pins +#define TX_ENABLE_PIN 12 +#define RX_ENABLE_PIN 13 + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENA_PIN 10 // Pullup or pulldown! +#define SPINDLE_DIR_PIN 11 +#if GEN7_VERSION < 13 + #define SPINDLE_LASER_PWM_PIN 16 // Hardware PWM +#else // Gen7 v1.3 removed the I2C connector & signals so need to get PWM off the PC power supply header + #define SPINDLE_LASER_PWM_PIN 15 // Hardware PWM +#endif diff --git a/Marlin/src/pins/sanguino/pins_GEN7_13.h b/Marlin/src/pins/sanguino/pins_GEN7_13.h new file mode 100644 index 0000000..55881aa --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_GEN7_13.h @@ -0,0 +1,54 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Gen7 v1.3 pin assignments + */ + +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +#define BOARD_INFO_NAME "Gen7 v1.3" + +#define GEN7_VERSION 13 // v1.3 +#include "pins_GEN7_12.h" diff --git a/Marlin/src/pins/sanguino/pins_GEN7_14.h b/Marlin/src/pins/sanguino/pins_GEN7_14.h new file mode 100644 index 0000000..66dba53 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_GEN7_14.h @@ -0,0 +1,120 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Gen7 v1.4 pin assignments + */ + +/** + * Rev B 26 DEC 2016 + * + * 1) added pointer to a current Arduino IDE extension + * 2) added support for M3, M4 & M5 spindle control commands + * 3) added case light pin definition + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega644__, __AVR_ATmega1284P__) + #error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644', 'ATmega644P', or 'ATmega1284P' in 'Tools > Processor.'" +#endif + +#define BOARD_INFO_NAME "Gen7 v1.4" + +#define GEN7_VERSION 14 // v1.4 + +// +// Limit switches +// +#define X_STOP_PIN 0 +#define Y_STOP_PIN 1 +#define Z_STOP_PIN 2 + +// +// Steppers +// +#define X_STEP_PIN 29 +#define X_DIR_PIN 28 +#define X_ENABLE_PIN 25 + +#define Y_STEP_PIN 27 +#define Y_DIR_PIN 26 +#define Y_ENABLE_PIN 25 + +#define Z_STEP_PIN 23 +#define Z_DIR_PIN 22 +#define Z_ENABLE_PIN 25 + +#define E0_STEP_PIN 19 +#define E0_DIR_PIN 18 +#define E0_ENABLE_PIN 25 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 1 // Analog Input +#define TEMP_BED_PIN 0 // Analog Input + +// +// Heaters +// +#define HEATER_0_PIN 4 +#define HEATER_BED_PIN 3 + +// +// Misc. Functions +// +#define PS_ON_PIN 15 + +#ifndef CASE_LIGHT_PIN + #define CASE_LIGHT_PIN 15 // Hardware PWM +#endif + +// A pin for debugging +#define DEBUG_PIN 0 + +// RS485 pins +#define TX_ENABLE_PIN 12 +#define RX_ENABLE_PIN 13 + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENA_PIN 20 // Pullup or pulldown! +#define SPINDLE_LASER_PWM_PIN 16 // Hardware PWM +#define SPINDLE_DIR_PIN 21 diff --git a/Marlin/src/pins/sanguino/pins_GEN7_CUSTOM.h b/Marlin/src/pins/sanguino/pins_GEN7_CUSTOM.h new file mode 100644 index 0000000..0c4871f --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_GEN7_CUSTOM.h @@ -0,0 +1,140 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Gen7 Alfons3 board pin assignments + * + * These Pins are assigned for the modified GEN7 Board from Alfons3. + * Please review the pins and adjust them for your needs. + */ + +/** + * Rev B 26 DEC 2016 + * + * 1) added pointer to a current Arduino IDE extension + * 2) added support for M3, M4 & M5 spindle control commands + * 3) added case light pin definition + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega644__, __AVR_ATmega1284P__) + #error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644', 'ATmega644P', or 'ATmega1284P' in 'Tools > Processor.'" +#endif + +#define BOARD_INFO_NAME "Gen7 Custom" + +// +// Limit Switches +// +#define X_STOP_PIN 0 +#define Y_STOP_PIN 1 +#define Z_STOP_PIN 2 + +// +// Steppers +// +#define X_STEP_PIN 21 // different from standard GEN7 +#define X_DIR_PIN 20 // different from standard GEN7 +#define X_ENABLE_PIN 24 + +#define Y_STEP_PIN 23 +#define Y_DIR_PIN 22 +#define Y_ENABLE_PIN 24 + +#define Z_STEP_PIN 26 +#define Z_DIR_PIN 25 +#define Z_ENABLE_PIN 24 + +#define E0_STEP_PIN 28 +#define E0_DIR_PIN 27 +#define E0_ENABLE_PIN 24 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 2 // Analog Input +#define TEMP_BED_PIN 1 // Analog Input (pin 34 bed) + +// +// Heaters +// +#define HEATER_0_PIN 4 +#define HEATER_BED_PIN 3 // (bed) + +// +// Misc. Functions +// +#define SDSS 31 // SCL pin of I2C header || CS Pin for SD Card support +#define PS_ON_PIN 19 + +#ifndef CASE_LIGHT_PIN + #define CASE_LIGHT_PIN 15 // Hardware PWM +#endif + +// A pin for debugging +#define DEBUG_PIN -1 + +// +// LCD / Controller +// +#define BEEPER_PIN -1 + +// 4bit LCD Support +#define LCD_PINS_RS 18 +#define LCD_PINS_ENABLE 17 +#define LCD_PINS_D4 16 +#define LCD_PINS_D5 15 +#define LCD_PINS_D6 13 +#define LCD_PINS_D7 14 + +// Buttons are directly attached +#define BTN_EN1 11 +#define BTN_EN2 10 +#define BTN_ENC 12 + +// RS485 pins +//#define TX_ENABLE_PIN 12 +//#define RX_ENABLE_PIN 13 + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENA_PIN 5 // Pullup or pulldown! +#define SPINDLE_LASER_PWM_PIN 16 // Hardware PWM +#define SPINDLE_DIR_PIN 6 diff --git a/Marlin/src/pins/sanguino/pins_MELZI.h b/Marlin/src/pins/sanguino/pins_MELZI.h new file mode 100644 index 0000000..887aae1 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_MELZI.h @@ -0,0 +1,32 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Melzi pin assignments + */ + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "Melzi" +#endif + +#include "pins_SANGUINOLOLU_12.h" diff --git a/Marlin/src/pins/sanguino/pins_MELZI_CREALITY.h b/Marlin/src/pins/sanguino/pins_MELZI_CREALITY.h new file mode 100644 index 0000000..97db36d --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_MELZI_CREALITY.h @@ -0,0 +1,143 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Melzi (Creality) pin assignments + * + * The Creality board needs a bootloader installed before Marlin can be uploaded. + * If you don't have a chip programmer you can use a spare Arduino plus a few + * electronic components to write the bootloader. + * + * See https://www.instructables.com/id/Burn-Arduino-Bootloader-with-Arduino-MEGA/ + * + * Schematic: https://bit.ly/2XOnsWb + */ + +#define BOARD_INFO_NAME "Melzi (Creality)" + +// Alter timing for graphical display +#if HAS_MARLINUI_U8GLIB + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 DELAY_NS(125) + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 DELAY_NS(125) + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 DELAY_NS(125) + #endif +#endif + +#include "pins_MELZI.h" + +// +// For the stock CR-10 enable CR10_STOCKDISPLAY in Configuration.h +// +#undef LCD_SDSS +#undef LED_PIN +#undef LCD_PINS_RS +#undef LCD_PINS_ENABLE +#undef LCD_PINS_D4 +#undef LCD_PINS_D5 +#undef LCD_PINS_D6 +#undef LCD_PINS_D7 + +#define LCD_SDSS 31 // Smart Controller SD card reader (rather than the Melzi) +#define LCD_PINS_RS 28 // ST9720 CS +#define LCD_PINS_ENABLE 17 // ST9720 DAT +#define LCD_PINS_D4 30 // ST9720 CLK + +#if ENABLED(BLTOUCH) + #define SERVO0_PIN 27 + #undef BEEPER_PIN +#elif ENABLED(FILAMENT_RUNOUT_SENSOR) + #ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN 27 + #endif + #if FIL_RUNOUT_PIN == BEEPER_PIN + #undef BEEPER_PIN + #endif +#endif + +#if ENABLED(MINIPANEL) + #undef DOGLCD_CS + #define DOGLCD_CS LCD_PINS_RS +#endif + +/** + PIN: 0 Port: B0 E0_DIR_PIN protected + PIN: 1 Port: B1 E0_STEP_PIN protected + PIN: 2 Port: B2 Z_DIR_PIN protected + PIN: 3 Port: B3 Z_STEP_PIN protected + PIN: 4 Port: B4 AVR_SS_PIN protected + . FAN_PIN protected + . SD_SS_PIN protected + PIN: 5 Port: B5 AVR_MOSI_PIN Output = 1 + . SD_MOSI_PIN Output = 1 + PIN: 6 Port: B6 AVR_MISO_PIN Input = 0 TIMER3A PWM: 0 WGM: 1 COM3A: 0 CS: 3 TCCR3A: 1 TCCR3B: 3 TIMSK3: 0 + . SD_MISO_PIN Input = 0 + PIN: 7 Port: B7 AVR_SCK_PIN Output = 0 TIMER3B PWM: 0 WGM: 1 COM3B: 0 CS: 3 TCCR3A: 1 TCCR3B: 3 TIMSK3: 0 + . SD_SCK_PIN Output = 0 + PIN: 8 Port: D0 RXD Input = 1 + PIN: 9 Port: D1 TXD Input = 0 + PIN: 10 Port: D2 BTN_EN2 Input = 1 + PIN: 11 Port: D3 BTN_EN1 Input = 1 + PIN: 12 Port: D4 HEATER_BED_PIN protected + PIN: 13 Port: D5 HEATER_0_PIN protected + PIN: 14 Port: D6 E0_ENABLE_PIN protected + . X_ENABLE_PIN protected + . Y_ENABLE_PIN protected + PIN: 15 Port: D7 X_STEP_PIN protected + PIN: 16 Port: C0 BTN_ENC Input = 1 + . SCL Input = 1 + PIN: 17 Port: C1 LCD_PINS_ENABLE Output = 0 + . SDA Output = 0 + PIN: 18 Port: C2 X_MIN_PIN protected + . X_STOP_PIN protected + PIN: 19 Port: C3 Y_MIN_PIN protected + . Y_STOP_PIN protected + PIN: 20 Port: C4 Z_MIN_PIN protected + . Z_STOP_PIN protected + PIN: 21 Port: C5 X_DIR_PIN protected + PIN: 22 Port: C6 Y_STEP_PIN protected + PIN: 23 Port: C7 Y_DIR_PIN protected + PIN: 24 Port: A7 TEMP_0_PIN protected + PIN: 25 Port: A6 TEMP_BED_PIN protected + PIN: 26 Port: A5 Z_ENABLE_PIN protected + PIN: 27 Port: A4 BEEPER_PIN Output = 0 + PIN: 28 Port: A3 LCD_PINS_RS Output = 0 + PIN: 29 Port: A2 <unused/unknown> Input = 0 + PIN: 30 Port: A1 LCD_PINS_D4 Output = 1 + PIN: 31 Port: A0 SDSS Output = 1 +*/ + +/** + * EXP1 Connector EXP1 as CR10 STOCKDISPLAY + * _____ _____ + * PA4 | 6 5 | PC0 BEEPER_PIN | 6 5 | BTN_ENC + * PD3 | 7 4 | RESET BTN_EN1 | 7 4 | RESET + * PD2 8 3 | PA1 BTN_EN2 8 3 | LCD_PINS_D4 (ST9720 CLK) + * PA3 | 9 2 | PC1 (ST9720 CS) LCD_PINS_RS | 9 2 | LCD_PINS_ENABLE (ST9720 DAT) + * GND |10 1 | 5V GND |10 1 | 5V + * ----- ----- + */ diff --git a/Marlin/src/pins/sanguino/pins_MELZI_MAKR3D.h b/Marlin/src/pins/sanguino/pins_MELZI_MAKR3D.h new file mode 100644 index 0000000..0e09c1f --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_MELZI_MAKR3D.h @@ -0,0 +1,29 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Melzi with ATmega1284 (MaKr3d version) pin assignments + */ + +#define BOARD_INFO_NAME "Melzi (ATmega1284)" +#include "pins_MELZI.h" diff --git a/Marlin/src/pins/sanguino/pins_MELZI_MALYAN.h b/Marlin/src/pins/sanguino/pins_MELZI_MALYAN.h new file mode 100644 index 0000000..8b4faee --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_MELZI_MALYAN.h @@ -0,0 +1,58 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Melzi (Malyan M150) pin assignments + */ + +#define BOARD_INFO_NAME "Melzi (Malyan)" + +// Alter timing for graphical display +#if HAS_MARLINUI_U8GLIB + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 DELAY_NS(125) + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 DELAY_NS(125) + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 DELAY_NS(125) + #endif +#endif + +#include "pins_MELZI.h" + +#undef LCD_SDSS +#undef LCD_PINS_RS +#undef LCD_PINS_ENABLE +#undef LCD_PINS_D4 +#undef BTN_EN1 +#undef BTN_EN2 +#undef BTN_ENC + +#define LCD_PINS_RS 17 // ST9720 CS +#define LCD_PINS_ENABLE 16 // ST9720 DAT +#define LCD_PINS_D4 11 // ST9720 CLK +#define BTN_EN1 30 +#define BTN_EN2 29 +#define BTN_ENC 28 diff --git a/Marlin/src/pins/sanguino/pins_MELZI_TRONXY.h b/Marlin/src/pins/sanguino/pins_MELZI_TRONXY.h new file mode 100644 index 0000000..f878941 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_MELZI_TRONXY.h @@ -0,0 +1,65 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Melzi pin assignments + */ + +#define BOARD_INFO_NAME "Melzi (Tronxy)" + +#if HAS_MARLINUI_U8GLIB + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 DELAY_NS(0) + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 DELAY_NS(125) + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 DELAY_NS(0) + #endif +#endif + +#include "pins_MELZI.h" + +#undef Z_ENABLE_PIN +#undef LCD_PINS_RS +#undef LCD_PINS_ENABLE +#undef LCD_PINS_D4 +#undef LCD_PINS_D5 +#undef LCD_PINS_D6 +#undef LCD_PINS_D7 +#undef BTN_EN1 +#undef BTN_EN2 +#undef BTN_ENC +#undef LCD_SDSS + +#define Z_ENABLE_PIN 14 +#define LCD_PINS_RS 30 +#define LCD_PINS_ENABLE 28 +#define LCD_PINS_D4 16 +#define LCD_PINS_D5 17 +#define LCD_PINS_D6 27 +#define LCD_PINS_D7 29 +#define BTN_EN1 10 +#define BTN_EN2 11 +#define BTN_ENC 26 diff --git a/Marlin/src/pins/sanguino/pins_MELZI_V2.h b/Marlin/src/pins/sanguino/pins_MELZI_V2.h new file mode 100644 index 0000000..275498d --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_MELZI_V2.h @@ -0,0 +1,39 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Melzi V2.0 as found at https://www.reprap.org/wiki/Melzi + */ + +#define BOARD_INFO_NAME "Melzi V2" + +#if HAS_MARLINUI_U8GLIB + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 DELAY_NS(0) + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 DELAY_NS(188) + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 DELAY_NS(0) + #endif +#endif + +#include "pins_MELZI.h" diff --git a/Marlin/src/pins/sanguino/pins_OMCA.h b/Marlin/src/pins/sanguino/pins_OMCA.h new file mode 100644 index 0000000..7f18283 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_OMCA.h @@ -0,0 +1,149 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Open Motion controller with enable based extruders (Final!) + * + * ATmega644 + * + * +---\/---+ + * (D 0) PB0 1| |40 PA0 (AI 0 / D31) + * (D 1) PB1 2| |39 PA1 (AI 1 / D30) + * INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29) + * PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28) + * PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27) + * MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26) + * MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25) + * SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24) + * RST 9| |32 AREF + * VCC 10| |31 GND + * GND 11| |30 AVCC + * XTAL2 12| |29 PC7 (D 23) + * XTAL1 13| |28 PC6 (D 22) + * RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI + * TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO + * INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS + * INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK + * PWM (D 12) PD4 18| |23 PC1 (D 17) SDA + * PWM (D 13) PD5 19| |22 PC0 (D 16) SCL + * PWM (D 14) PD6 20| |21 PD7 (D 15) PWM + * +--------+ + * + * REF http://sanguino.wikidot.com/hardware + */ + +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at http://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega644__) + #error "Oops! Select 'Sanguino' in 'Tools > Board' and 'ATmega644' or 'ATmega644P' in 'Tools > Processor.'" +#endif + +#define BOARD_INFO_NAME "Final OMCA" + +// +// Limit Switches +// +#define X_STOP_PIN 0 +#define Y_STOP_PIN 1 +#define Z_STOP_PIN 2 + +// +// Steppers +// +#define X_STEP_PIN 26 +#define X_DIR_PIN 25 +#define X_ENABLE_PIN 10 + +#define Y_STEP_PIN 28 +#define Y_DIR_PIN 27 +#define Y_ENABLE_PIN 10 + +#define Z_STEP_PIN 23 +#define Z_DIR_PIN 22 +#define Z_ENABLE_PIN 10 + +#define E0_STEP_PIN 24 +#define E0_DIR_PIN 21 +#define E0_ENABLE_PIN 10 + +#define E1_STEP_PIN -1 // 21 +#define E1_DIR_PIN -1 // 20 +#define E1_ENABLE_PIN -1 // 19 + +#define E2_STEP_PIN -1 // 21 +#define E2_DIR_PIN -1 // 20 +#define E2_ENABLE_PIN -1 // 18 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // Analog Input +#define TEMP_1_PIN 1 // Analog Input +#define TEMP_BED_PIN 2 // Analog Input (1,2 or I2C) + +// +// Heaters / Fans +// +#define HEATER_0_PIN 3 // DONE PWM on RIGHT connector +#define HEATER_BED_PIN 4 + +#ifndef FAN_PIN + #define FAN_PIN 14 // PWM on MIDDLE connector +#endif + +// +// Misc. Functions +// +#define SDSS 11 + +#define I2C_SCL_PIN 16 +#define I2C_SDA_PIN 17 + +// future proofing +#define __FS 20 +#define __FD 19 +#define __GS 18 +#define __GD 13 + +#define UNUSED_PWM 14 // PWM on LEFT connector diff --git a/Marlin/src/pins/sanguino/pins_OMCA_A.h b/Marlin/src/pins/sanguino/pins_OMCA_A.h new file mode 100644 index 0000000..7707320 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_OMCA_A.h @@ -0,0 +1,135 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Open Motion controller with enable based extruders (Alpha!) + * + * ATmega644 + * + * +---\/---+ + * (D 0) PB0 1| |40 PA0 (AI 0 / D31) + * (D 1) PB1 2| |39 PA1 (AI 1 / D30) + * INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29) + * PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28) + * PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27) + * MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26) + * MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25) + * SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24) + * RST 9| |32 AREF + * VCC 10| |31 GND + * GND 11| |30 AVCC + * XTAL2 12| |29 PC7 (D 23) + * XTAL1 13| |28 PC6 (D 22) + * RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI + * TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO + * INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS + * INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK + * PWM (D 12) PD4 18| |23 PC1 (D 17) SDA + * PWM (D 13) PD5 19| |22 PC0 (D 16) SCL + * PWM (D 14) PD6 20| |21 PD7 (D 15) PWM + * +--------+ + */ + +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +#if NOT_TARGET(__AVR_ATmega644__) + #error "Oops! Select 'Sanguino' in 'Tools > Board' and ATmega644 in 'Tools > Processor.'" +#endif + +#define BOARD_INFO_NAME "Alpha OMCA" + +// +// Limit Switches +// +#define X_STOP_PIN 0 +#define Y_STOP_PIN 1 +#define Z_STOP_PIN 2 + +// +// Steppers +// +#define X_STEP_PIN 21 +#define X_DIR_PIN 20 +#define X_ENABLE_PIN 24 + +#define Y_STEP_PIN 23 +#define Y_DIR_PIN 22 +#define Y_ENABLE_PIN 24 + +#define Z_STEP_PIN 26 +#define Z_DIR_PIN 25 +#define Z_ENABLE_PIN 24 + +#define E0_STEP_PIN 28 +#define E0_DIR_PIN 27 +#define E0_ENABLE_PIN 24 + +#define E1_STEP_PIN -1 // 19 +#define E1_DIR_PIN -1 // 18 +#define E1_ENABLE_PIN 24 + +#define E2_STEP_PIN -1 // 17 +#define E2_DIR_PIN -1 // 16 +#define E2_ENABLE_PIN 24 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // Analog Input (D27) + +// +// Heaters / Fans +// +#define HEATER_0_PIN 4 + +#ifndef FAN_PIN + #define FAN_PIN 3 +#endif + +// +// Misc. Functions +// +#define SDSS 11 + +/* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */ diff --git a/Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h b/Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h new file mode 100644 index 0000000..af27159 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h @@ -0,0 +1,344 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Sanguinololu board pin assignments + */ + +/** + * Rev B 26 DEC 2016 + * + * 1) added pointer to a current Arduino IDE extension + * 2) added support for M3, M4 & M5 spindle control commands + * 3) added case light pin definition + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega1284P__) + #error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644P' or 'ATmega1284P' in 'Tools > Processor.'" +#endif + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "Sanguinololu <1.2" +#endif + +// +// Limit Switches +// +#define X_STOP_PIN 18 +#define Y_STOP_PIN 19 +#define Z_STOP_PIN 20 + +// +// Steppers +// +#define X_STEP_PIN 15 +#define X_DIR_PIN 21 + +#define Y_STEP_PIN 22 +#define Y_DIR_PIN 23 + +#define Z_STEP_PIN 3 +#define Z_DIR_PIN 2 + +#define E0_STEP_PIN 1 +#define E0_DIR_PIN 0 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 7 // Analog Input (pin 33 extruder) +#define TEMP_BED_PIN 6 // Analog Input (pin 34 bed) + +// +// Heaters / Fans +// +#define HEATER_0_PIN 13 // (extruder) + +#if ENABLED(SANGUINOLOLU_V_1_2) + + #define HEATER_BED_PIN 12 // (bed) + #define X_ENABLE_PIN 14 + #define Y_ENABLE_PIN 14 + #define Z_ENABLE_PIN 26 + #define E0_ENABLE_PIN 14 + + #if !defined(FAN_PIN) && ENABLED(LCD_I2C_PANELOLU2) + #define FAN_PIN 4 // Uses Transistor1 (PWM) on Panelolu2's Sanguino Adapter Board to drive the fan + #endif + +#else + + #define HEATER_BED_PIN 14 // (bed) + #define X_ENABLE_PIN 4 + #define Y_ENABLE_PIN 4 + #define Z_ENABLE_PIN 4 + #define E0_ENABLE_PIN 4 + +#endif + +#if !defined(FAN_PIN) && (MB(AZTEEG_X1, STB_11) || IS_MELZI) + #define FAN_PIN 4 // Works for Panelolu2 too +#endif + +// +// Misc. Functions +// + +/** + * In some versions of the Sanguino libraries the pin + * definitions are wrong, with SDSS = 24 and LED_PIN = 28 (Melzi). + * If you encounter issues with these pins, upgrade your + * Sanguino libraries! See #368. + */ +//#define SDSS 24 +#define SDSS 31 + +#if IS_MELZI + #define LED_PIN 27 +#elif MB(STB_11) + #define LCD_BACKLIGHT_PIN 17 // LCD backlight LED +#endif + +#if NONE(SPINDLE_FEATURE, LASER_FEATURE) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // try to use IO Header + #define CASE_LIGHT_PIN 4 // Hardware PWM - see if IO Header is available +#endif + +/** + * Sanguinololu 1.4 AUX pins: + * + * PWM TX1 RX1 SDA SCL + * 12V 5V D12 D11 D10 D17 D16 + * GND GND D31 D30 D29 D28 D27 + * A4 A3 A2 A1 A0 + */ + +// +// LCD / Controller +// +#if HAS_WIRED_LCD + + #define SD_DETECT_PIN -1 + + #if HAS_MARLINUI_U8GLIB + + #if ENABLED(LCD_FOR_MELZI) + + #define LCD_PINS_RS 17 + #define LCD_PINS_ENABLE 16 + #define LCD_PINS_D4 11 + #define KILL_PIN 10 + #define BEEPER_PIN 27 + + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 DELAY_NS(0) + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 DELAY_NS(188) + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 DELAY_NS(0) + #endif + + #elif ENABLED(U8GLIB_ST7920) // SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0 + + #if IS_MELZI + #define LCD_PINS_RS 30 // CS chip select /SS chip slave select + #define LCD_PINS_ENABLE 29 // SID (MOSI) + #define LCD_PINS_D4 17 // SCK (CLK) clock + // Pin 27 is taken by LED_PIN, but Melzi LED does nothing with + // Marlin so this can be used for BEEPER_PIN. You can use this pin + // with M42 instead of BEEPER_PIN. + #define BEEPER_PIN 27 + + #if IS_RRD_FG_SC + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 DELAY_NS(0) + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 DELAY_NS(188) + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 DELAY_NS(0) + #endif + #endif + + #else // Sanguinololu >=1.3 + #define LCD_PINS_RS 4 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 30 + #define LCD_PINS_D5 29 + #define LCD_PINS_D6 28 + #define LCD_PINS_D7 27 + #endif + + #else + + #define DOGLCD_A0 30 + + #if ENABLED(MAKRPANEL) + + #define BEEPER_PIN 29 + #define DOGLCD_CS 17 + #define LCD_BACKLIGHT_PIN 28 // PA3 + + #elif IS_MELZI + + #define BEEPER_PIN 27 + #define DOGLCD_CS 28 + + #else // !MAKRPANEL + + #define DOGLCD_CS 29 + + #endif + + #endif + + // Uncomment screen orientation + //#define LCD_SCREEN_ROT_0 + //#define LCD_SCREEN_ROT_90 + //#define LCD_SCREEN_ROT_180 + //#define LCD_SCREEN_ROT_270 + + #elif ENABLED(ZONESTAR_LCD) // For the Tronxy Melzi boards + + #define LCD_PINS_RS 28 + #define LCD_PINS_ENABLE 29 + #define LCD_PINS_D4 10 + #define LCD_PINS_D5 11 + #define LCD_PINS_D6 16 + #define LCD_PINS_D7 17 + + #else + + #define LCD_PINS_RS 4 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 30 + #define LCD_PINS_D5 29 + #define LCD_PINS_D6 28 + #define LCD_PINS_D7 27 + + #endif + + #if ENABLED(LCD_FOR_MELZI) + + #define BTN_ENC 28 + #define BTN_EN1 29 + #define BTN_EN2 30 + + #elif ENABLED(ZONESTAR_LCD) // For the Tronxy Melzi boards + + #define ADC_KEYPAD_PIN 1 + #define BTN_EN1 -1 + #define BTN_EN2 -1 + + #elif ENABLED(LCD_I2C_PANELOLU2) + + #if IS_MELZI + #define BTN_ENC 29 + #define LCD_SDSS 30 // Panelolu2 SD card reader rather than the Melzi + #else + #define BTN_ENC 30 + #endif + + #else // !LCD_FOR_MELZI && !ZONESTAR_LCD && !LCD_I2C_PANELOLU2 + + #define BTN_ENC 16 + #define LCD_SDSS 28 // Smart Controller SD card reader rather than the Melzi + + #endif + + #if IS_NEWPANEL && !defined(BTN_EN1) + #define BTN_EN1 11 + #define BTN_EN2 10 + #endif + +#endif // HAS_WIRED_LCD + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if HAS_CUTTER + #if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // try to use IO Header + + #define SPINDLE_LASER_ENA_PIN 10 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 4 // Hardware PWM + #define SPINDLE_DIR_PIN 11 + + #elif !MB(MELZI) // use X stepper motor socket + + /** + * To control the spindle speed and have an LCD you must sacrifice + * the Extruder and pull some signals off the X stepper driver socket. + * + * The following assumes: + * - The X stepper driver socket is empty + * - The extruder driver socket has a driver board plugged into it + * - The X stepper wires are attached the the extruder connector + */ + + /** + * Where to get the spindle signals + * + * spindle signal socket name socket name + * ------- + * /ENABLE O| |O VMOT + * MS1 O| |O GND + * MS2 O| |O 2B + * MS3 O| |O 2A + * /RESET O| |O 1A + * /SLEEP O| |O 1B + * SPINDLE_LASER_PWM_PIN STEP O| |O VDD + * SPINDLE_LASER_ENA_PIN DIR O| |O GND + * ------- + * + * Note: Socket names vary from vendor to vendor. + */ + #undef X_DIR_PIN + #undef X_ENABLE_PIN + #undef X_STEP_PIN + #define X_DIR_PIN 0 + #define X_ENABLE_PIN 14 + #define X_STEP_PIN 1 + #define SPINDLE_LASER_PWM_PIN 15 // Hardware PWM + #define SPINDLE_LASER_ENA_PIN 21 // Pullup! + #define SPINDLE_DIR_PIN -1 // No pin available on the socket for the direction pin + #endif +#endif diff --git a/Marlin/src/pins/sanguino/pins_SANGUINOLOLU_12.h b/Marlin/src/pins/sanguino/pins_SANGUINOLOLU_12.h new file mode 100644 index 0000000..c5c8b4f --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_SANGUINOLOLU_12.h @@ -0,0 +1,42 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Sanguinololu V1.2 pin assignments + * + * Applies to the following boards: + * + * AZTEEG_X1 + * MELZI + * MELZI_CREALITY + * MELZI_MAKR3D + * SANGUINOLOLU_12 + * STB_11 + */ + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "Sanguinololu 1.2" +#endif + +#define SANGUINOLOLU_V_1_2 +#include "pins_SANGUINOLOLU_11.h" diff --git a/Marlin/src/pins/sanguino/pins_SETHI.h b/Marlin/src/pins/sanguino/pins_SETHI.h new file mode 100644 index 0000000..dc2133e --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_SETHI.h @@ -0,0 +1,124 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * Sethi 3D_1 pin assignments - www.sethi3d.com.br + */ + +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + * this assumes that this board uses the Sanguino pin map + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + */ + +#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega644__, __AVR_ATmega1284P__) + #error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644', 'ATmega644P', or 'ATmega1284P' in 'Tools > Processor.'" +#endif + +#define BOARD_INFO_NAME "Sethi 3D_1" + +#ifndef GEN7_VERSION + #define GEN7_VERSION 12 // v1.x +#endif + +// +// Limit Switches +// +#define X_STOP_PIN 2 +#define Y_STOP_PIN 0 +#define Z_MIN_PIN 1 +#define Z_MAX_PIN 0 + +// +// Steppers +// +#define X_STEP_PIN 19 +#define X_DIR_PIN 18 +#define X_ENABLE_PIN 24 + +#define Y_STEP_PIN 23 +#define Y_DIR_PIN 22 +#define Y_ENABLE_PIN 24 + +#define Z_STEP_PIN 26 +#define Z_DIR_PIN 25 +#define Z_ENABLE_PIN 24 + +#define E0_STEP_PIN 28 +#define E0_DIR_PIN 27 +#define E0_ENABLE_PIN 24 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 1 // Analog Input +#define TEMP_BED_PIN 2 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 4 +#define HEATER_BED_PIN 3 + +#ifndef FAN_PIN + #if GEN7_VERSION >= 13 + // Gen7 v1.3 removed the fan pin + #define FAN_PIN -1 + #else + #define FAN_PIN 31 + #endif +#endif + +// +// Misc. Functions +// +#define PS_ON_PIN 15 + +// All these generations of Gen7 supply thermistor power +// via PS_ON, so ignore bad thermistor readings +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 + +// our pin for debugging. +#define DEBUG_PIN 0 + +// our RS485 pins +#define TX_ENABLE_PIN 12 +#define RX_ENABLE_PIN 13 diff --git a/Marlin/src/pins/sanguino/pins_STB_11.h b/Marlin/src/pins/sanguino/pins_STB_11.h new file mode 100644 index 0000000..b10a098 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_STB_11.h @@ -0,0 +1,30 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +/** + * STB V1.1 pin assignments + */ + +#define BOARD_INFO_NAME "STB V1.1" + +#include "pins_SANGUINOLOLU_12.h" diff --git a/Marlin/src/pins/sanguino/pins_ZMIB_V2.h b/Marlin/src/pins/sanguino/pins_ZMIB_V2.h new file mode 100644 index 0000000..d064d80 --- /dev/null +++ b/Marlin/src/pins/sanguino/pins_ZMIB_V2.h @@ -0,0 +1,234 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <https://www.gnu.org/licenses/>. + * + */ +#pragma once + +#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega1284P__) + #error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644P' or 'ATmega1284P' in 'Tools > Processor.'" +#endif + +#define BOARD_INFO_NAME "Zonestar ZMIB_V2" +#define BOARD_WEBSITE_URL "www.aliexpress.com/item/32957490744.html" + +#define IS_ZMIB_V2 + +/** + * ZMIB pin assignments + * + * The ZMIB board needs a bootloader installed before Marlin can be uploaded. + * If you don't have a chip programmer you can use a spare Arduino plus a few + * electronic components to write the bootloader. + * + * See http://www.instructables.com/id/Burn-Arduino-Bootloader-with-Arduino-MEGA/ + */ + +/** + * PIN: 0 Port: B0 HEATER_0_PIN + * PIN: 1 Port: B1 HEATER_BED_PIN + * PIN: 2 Port: B2 EXP1_4(BTN_EN2) + * PIN: 3 Port: B3 V1: SD_DETECT_PIN + * PIN: 3 Port: B3 V2: EXP1_6 + * PIN: 4 Port: B4 SDSS + * PIN: 4 Port: B4 V1: EXP1_6 + * PIN: 5 Port: B5 AVR_MOSI_PIN + * . SD_MOSI_PIN + * PIN: 6 Port: B6 AVR_MISO_PIN + * . EXP1_9(SD_MISO_PIN) + * PIN: 7 Port: B7 AVR_SCK_PIN + * . EXP1_10(SD_SCK_PIN) + * PIN: 8 Port: D0 RXD + * PIN: 9 Port: D1 TXD + * PIN: 10 Port: D2 EXP1_8 + * PIN: 11 Port: D3 EXP1_7 + * PIN: 12 Port: D4 EXP1_5(BTN_EN1) + * PIN: 13 Port: D5 Z_MIN_PIN + * PIN: 14 Port: D6 E1_DIR_PIN + * PIN: 15 Port: D7 E1_STEP_PIN + * PIN: 16 Port: C0 Z_DIR_PIN + * PIN: 17 Port: C1 Z_STEP_PIN + * PIN: 18 Port: C2 Y_MIN_PIN + * PIN: 19 Port: C3 Y_DIR_PIN + * PIN: 20 Port: C4 Y_STEP_PIN + * PIN: 21 Port: C5 X_MIN_PIN + * PIN: 22 Port: C6 X_DIR_PIN + * PIN: 23 Port: C7 X_STEP_PIN + * PIN: 24 Port: A7 X_ENABLE_PIN + * Y_ENABLE_PIN + * Z_ENABLE_PIN + * E0_ENABLE_PIN + * E1_ENABLE_PIN + * PIN: 25 Port: A6 FIL_RUNOUT_PIN + * PIN: 26 Port: A5 E0_DIR_PIN + * PIN: 27 Port: A4 E0_STEP_PIN + * PIN: 28 Port: A3 FAN_PIN + * PIN: 29 Port: A2 EXP1_3(BTN_ENC) + * ADC_KEY_PIN + * PIN: 30 Port: A1 TEMP_0_PIN + * PIN: 31 Port: A0 TEMP_BED_PIN + */ + +// +// Limit Switches +// +#define X_MIN_PIN 21 +#define Y_MIN_PIN 18 + +#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT) + #define Z_MIN_PIN 25 +#else + #define Z_MIN_PIN 13 +#endif + +// +// Steppers +// +#define X_STEP_PIN 23 +#define X_DIR_PIN 22 +#define X_ENABLE_PIN 24 + +#define Y_STEP_PIN 20 +#define Y_DIR_PIN 19 +#define Y_ENABLE_PIN 24 + +#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT) + #define Z_STEP_PIN 27 + #define Z_DIR_PIN 26 +#else + #define Z_STEP_PIN 17 + #define Z_DIR_PIN 16 +#endif + +#define Z_ENABLE_PIN 24 + +#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT) + #define E0_STEP_PIN 15 + #define E0_DIR_PIN 14 +#else + #define E0_STEP_PIN 27 + #define E0_DIR_PIN 26 +#endif + +#define E0_ENABLE_PIN 24 + +#define E1_STEP_PIN 15 +#define E1_DIR_PIN 14 +#define E1_ENABLE_PIN 24 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 1 // Analog Input +#define TEMP_BED_PIN 0 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 0 +#define HEATER_BED_PIN 1 +#define FAN_PIN 28 +#define FAN1_PIN -1 + +// +//filament run out sensor +// +#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT) + #define FIL_RUNOUT_PIN 13 +#else + #define FIL_RUNOUT_PIN 25 // Z-MIN +#endif + +// +// SD card +// +#if ENABLED(SDSUPPORT) + #define SDSS 4 +#endif +#define SD_DETECT_PIN -1 + +/*=================================================== + * ZMIB Version 1 - EXP1 Connector + * MOSI(D5) TX1(D11) ENA(D12) ENC(D29/A2) 5V + * SCK(D7) RX1(D10) SCS(D4) ENB(D2) GND + *=================================================== + * ZMIB Version 2 - EXP1 Connector + * MOSI(D5) TX1(D11) ENA(D12) ENC(D29/A2) 5V + * SCK(D7) RX1(D10) SCS(D3) ENB(D2) GND + *=================================================== + * LCD 128x64 + *==================================================*/ + +#if ENABLED(ZONESTAR_12864LCD) + // + // LCD 128x64 + // + #define LCDSCREEN_NAME "ZONESTAR_12864LCD" + #define FORCE_SOFT_SPI + //#define LCD_SDSS 11 + #define LCD_PINS_RS 11 // ST7920_CS_PIN LCD_PIN_RS (PIN4 of LCD module) + #ifdef IS_ZMIB_V2 + #define LCD_PINS_ENABLE 3 // ST7920_DAT_PIN LCD_PIN_R/W (PIN5 of LCD module) + #else + #define LCD_PINS_ENABLE 4 // ST7920_DAT_PIN LCD_PIN_R/W (PIN5 of LCD module) + #endif + #define LCD_PINS_D4 10 // ST7920_CLK_PIN LCD_PIN_ENABLE (PIN6 of LCD module) + + // Alter timing for graphical display + #define ST7920_DELAY_1 DELAY_2_NOP + #define ST7920_DELAY_2 DELAY_2_NOP + #define ST7920_DELAY_3 DELAY_2_NOP + +#elif EITHER(ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306) + // + // OLED 128x64 + // + #define LCDSCREEN_NAME "ZONESTAR 12864OLED" + #define FORCE_SOFT_SPI + #ifdef IS_ZMIB_V2 + #define LCD_PINS_RS 3 // RESET + #else + #define LCD_PINS_RS 4 // RESET + #endif + #define LCD_PINS_DC 10 // DC + #define DOGLCD_CS 11 // CS + #if ENABLED(OLED_HW_IIC) + #error "Oops! can't choose HW IIC for ZMIB board!!" + #elif ENABLED(OLED_HW_SPI) + // HW SPI + #define DOGLCD_A0 LCD_PINS_DC // A0 = DC + #else + // SW SPI + #define DOGLCD_A0 LCD_PINS_DC // A0 = DC + #define DOGLCD_MOSI AVR_MOSI_PIN // SDA + #define DOGLCD_SCK AVR_SCK_PIN // SCK + #endif + +#endif + +// +// All the above are also RRDSC with rotary encoder +// +#if IS_RRD_SC + #define BTN_EN1 2 + #define BTN_EN2 12 + #define BTN_ENC 29 + #define BEEPER_PIN -1 + #define KILL_PIN -1 +#endif |